Search Documents

By Lynn B. Hales

Unfortunately, the term "control" has a negative connotation in the minds of many of our operating plant personnel. Whereas the opposite is true of those associated with research and technical centers in our industry. The magnitude of this difference in opinion and actual experience has often proved to be a major factor influencing the success or failure of process control applications. Through the years, many plant people have endured a number of unsuccessful attempts by "outside" people to "optimize" their plants; and these experiences have proved to have had quite a callousing effect on them. On the other hand, in many plants, successful process control efforts have made firm allies of the operating personnel, and have increased the number of metallurgical people who are well qualified and experienced in process control. The instrumentation industry, computer industry, and the mining industry's ability to quantify what is really happening in our processes have grown and developed rapidly since the first control efforts were made in the 1930's (1). Because of this-,: new control opportunities are becoming increasingly more feasible and older well established ones are becoming even more practical and necessary with regard to the economic s of our industry.

Jan 1, 1979

By R. L. Taylor, S. D. Abbott

"INTRODUCTION Mines are filled with a mixture of gases, some of which are toxic, flammable, explosive. Others can be early reporters of potential problems. It has previously been shown that analysis by gas chromatograph can the most accurate conventional analytical tool for common mine gas mixtures when used correctly. There are some other detection methods (e.g hand held sensors), but they do not detect many situations which are immediately dangerous to life or health (IDLH). Examples include explosive hydrogen mixtures, toxic carbon dioxide levels, and some explosive mixtures of methane with oxygen. (Reference our previous paper). There are several reasons for mines to consider onsite GC analysis. (1) Timeliness of results. Samples can be taken and analyzed immediately. Samples do not have to be shipped to a lab and wait for results. (2) Ability to run greater number of samples a lower for the same cost. This allows mine to increase the number of samples taken to be more informed about the gases/conditions of the mine without the worry of financial constraints. (3) Fewer sample media needed, and there is no wear and tear or cost from shipping them offsite. When samples are shipped offsite, those sample media cannot be used to take until the lab returns them when the analysis is done onsite, the sample media can be used again almost immediately. However there are several challenges associated with using GC to analyze mine gas samples onsite. To date there has been a clash of the requirements for a successful analysis, the capabilities of the technology, and the practicalities of implementation. The purpose of this paper is to discuss some of the difficulties in getting accurate reliable data and doing so in an economic way. This whole measurement activity is a cost center for a mine, so there are economic concerns for the mine to address. These concerns are mainly staffing costs, capital costs, maintenance, and consumables costs. A properly staffed and equipped analysis lab, including burdened overhead, costs about $500K per year. At a sampling rate of 10 per day, this is about $140 per measurement for a proper onsite lab."

Jan 1, 2016

By Mortimer J. Richardson, Earl H. Malmstrom

INTRODUCTION The art of placer gold mine evaluation and mining has had an interesting evolution beginning in earliest times. DE RE METALLICA (c.1556), documents the use of rockers, circular sieves(jigs) and riff lest for classifying, concentrating and recovering placer gold, respectively. During the late 1800's in the heat of the international gold rush, a bucket ladder mining dredge containing its own processing plant was developed that enabled digging of placers to bedrock that were inaccessible to the hand miner. The power driven churn drill was developed at about the same tie that facilitated more rapid and larger scale sampling of placers to bedrock. The mineral jig was applied in the early part of the 1900,s to begin the replacement of riffles on placer dredges. Mining dredges proliferated in California and New Zealand to mine the deeper placers and spread throughout the world. The companies that were leaders in dredge mining technology conducted experimental work that advanced the state of the art by processing of gravels with jigs and amalgam systems to recover gold on board dredges in a continuous process. This paper will synthesize the technology of placer gold exploration, mine development and operation into guidelines for evaluation and development of small-scale prospects. Prospect Reconnaissance The location of a prospect usual1 y results from some physical evidence of the presence of gold and/or past mining activity. Any earlier activity that may have produced gold from the prospect, should be investigated before making the trip. The initial reconnaissance should attempt to verify a near-surface presence and then make observations concerning the geomorphic characteristics that relate to placer gold accumulation. Estimates of the probable depth, breadth and length of mineable gravels can be made from the surf ace by the experienced placer mining engineer. With this information, he can speculate on whether there is a viable prospect to be pursued. The placer mining engineer should be experienced in panning samples found in shallow diggings or from existing pits. This will give him immediate indications of gold presence without fear of "salting" by an over-ambitious promoter of the project. The same capability of panning is important during the other sampling phases. A thorough knowledge of logging and calculating the results is essential to proper evaluation of the deposit' s tenor. Evaluation Methods Depending upon the character of the prospect such as river, benches, terraces, jungle, the type of equipment to conduct sampling of the deposit must be determined. In most cases, the drill has replaced bulk sampling. The churn drill has had the greatest amount of accumulated experience but is slow. The reverse circulation drill (RC), is limited by its lack of verification in subsequent mining in order to prove its reliability. However, in the hands of knowledgeable placer mining engineers experienced with its use and calibration, it may be used. The RC Hammer drill (such as the Becker), can be as much as ten times faster than the churn drill and compress the time necessary to prove a prospect, or, to disprove it. All costs in balance, it is often cost effective over the churn drill.

Jan 1, 1987

By L. Andrews, G. Smits, M. D. Adams, E. A. Viljoen

A new approach has been developed that is capable of ascertaining the ore component that is responsible for the preg­robbing of pregnant pulps. Many gold mines are currently treating ores containing a component that is detrimental to the recovery of gold, in that they "preg-rob" the pregnant pulp by adsorption of some of the dissolved gold. The identity of the preg-robbing component in this type of ore has been the subject of considerable debate over a lengthy period, th various suggestions including amorphous carbon, chlonte, chalcopyrite and layered silicates, such as the phyllosilicate minerals pyrophyllite, kaolinite, phlogopite and illite. A means is now available to identify and characterize the preg-robber in gold ores. This new approach consists of contacting the ore with a synthetic aurocyanide solution, identifying the mineral grains by optical microscopy and analysing each grain individually using high-sensitivity electron microprobe analysis. The approach is exemplified in this initial study by identifying the preg-robbing component in an active sample of gold-bearing shale to be an amorphous carbonaceous phase consisting of discrete particles of about 5 µm diameter interspersed with shale particles and agglomerated into grains of up to 100 µm diameter. Microanalysis of these grains as well as other mineral particles revealed that the gold content of some of the carbonaceous grains was close to 7000 g,lt, with no gold being detected in any of the other mineral phases that were found to be present (e.g. quartz, chlorite, muscovite, pyrophyllite, etc). Bulk analysis of the sample for carbon and gold confirmed that gold loadings of around 7000 g,/t would be expected if all of the gold were adsorbed onto the carbonaceous component. The carbonaceous constituent is probably also responsible for the anomalously high surface area measured for the material. It probably acts in a similar fashion to activated carbon, and the correct choice of organic blinding agent will decrease the extent of preg-robbing by lowering the activity of the material for gold, without causing any downstream problems such as fouling of the activated carbon used for gold recovery

Jan 1, 1993

By J. Douglas

The past year has been a strange one for the fertilizer industry of the world and the United States. Listening to news stories, you would think the sky is falling on the world's agriculture and probably conclude that we should have had an exceptionally poor fertilizer season. In some respects, we did. Prices were low, profits were low, and in some cases nonexistent, but volume was good. We heard much in the press about the farmers' credit crunch. The truth of the matter is that only 6.6 percent of the U.S. farmers have debt-equity ratios of 70 percent or more, and a large percentage of our farmers have absolutely no debt but operate entirely on their own cash assets.

Jan 1, 1985

By Frank C. Stevens

The availability, cost and use of fuel and electricity for the cement industry is difficult to predict with a great degree of accuracy because the historical pattern of factors affecting energy was disrupted during the years 1972, 1973 and 1974. Forecasting is both an art and science and is based on .the premise that the best indicator of the future is the past. Statistical data is used to guide economists and businessmen in their predictions of the future. Even though the energy picture is changing, it is believed that electricity and fuel will be available for the cement industry in the foreseeable future, and this energy will be more costly in relation to the other items that are part of the manufacturing costs for portland cement.

Jan 1, 1977

By L. A. Alcorn, H. E. Camargo, G. Gwaltney

"One of the most pervasive diseases in the mining industry is noise-induced hearing loss. The exposure of miners to noise levels above the permissible exposure level results in hearing loss in approximately 80% of coal miners by retirement age. In this context, the U.S. National Institute for Occupational Safety and Health (NIOSH) is conducting research to develop noise controls for longwall mining systems, which are used to extract half of the national underground coal production.From field measurements, previous research determined that the dominant sound-radiating components at the shearer of a longwall system are the two cutting drums used to remove coal. Due to the dimensions and complexity of longwall mining systems, the NIOSH project developed a validated finite element model of the cutting drum to use in predicting the sound radiated by the drum due to the excitation forces experienced in underground operations. This same model will be used to develop engineering noise controls for the drum. The excitation forces arise from the interaction of the cutting bits and the coal and are transmitted to the cutting drum through the bit holders. Due to the adverse conditions at the face, and a lack of instrumentation approved for underground use, the operational coal cutting forces have not been assessed before. To this end, NIOSH, in collaboration with Michigan Technological University, developed a self-contained, intrinsically safe instrumented bit to measure these forces.This paper describes the development of the instrumented bit and the measuring of operational coal cutting forces at three working coal mines. The measurements revealed that the forces have a flat spectrum, representative of the impact nature of these forces, up to around 100 Hz. Above this cutoff frequency, the force magnitude decreases at a rate proportional to the inverse of frequency squared."

Jan 1, 2014

By C. B. Queja

Flexible synthetic membrane liners have become a standard facet to copper and gold heap leach pad design. While gold heap leach operations have utilized most types of synthetic liners, copper leach operations have commonly only been lined with polyethylene. The objective of this study was to determine if there are any chemical reasons why other synthetic membrane types could not be used to line a copper heap leach facility. With engineered consideration, the flexible membrane liner under the ore pile serves two purposes. The first provides a near impermeable boundary which aides greatly in the collection of the metal laden process solution. The second advantage to the flexible membrane is the almost non-permeable barrier to benefit increased environmental awareness that has led to an increase in solution containment technology. The Environmental Protection Agency (EPA) has developed a compatibility test for solutions and membrane liners. The EPA Method 9090 is intended for use in determining the chemical effects of a solution on the physical properties of the flexible membrane liner material intended to contain them. Data from these tests would assist in deciding whether a given liner material is acceptable for the intended application.

Jan 1, 1995

By Richard M. Crowell

"As thorough sampling is usually expensive, the cost of a complete job is often unwarranted, and a cheaper approximation must be substituted. The engineer should, however, weigh the situation thoroughly before subscribing to an alternative other than an accurate assay basis on which to build his conclusion." Examination and Valuation of Mineral Property. R. Parks, 1949

Jan 1, 1994

By MARK J. VANARELLI

Estimating groundwater inflows in rock deep tunnels is critical to the safety of personnel constructing the tunnel and the cost of construction. This paper presents two case studies for estimating steady-state groundwater inflows into deep rock tunnels. The case studies included the Chattahoochee and Nancy Creek tunnels. In this paper, statistical methods were applied to packer test data obtained from exploratory borings during geotechnical site investigations. A semi-empirical procedure was utilized for estimating groundwater inflows into these deep rock tunnels. The Chattahoochee and Nancy Creek tunnels are deep rock tunnels which exhibit radial flow conditions. For the radial flow condition, a statistical analysis presented in this paper indicates that the semi-empirical procedure works well; however, variations in the procedure and/or an insufficient amount of testing could lead to underestimations of the inflow quantities. Packer test data plotted in histograms were observed in all cases to be log-normally distributed for the radial flow condition. Modeling using Monte Carlo simulations was observed to be an effective tool for removing irregularities in the distribution of the data and incorporating high-end permeability data to derive reasonable groundwater inflow estimates.

Jun 13, 2021

By Greg Struble

The Homestake Gold Mine is one of the deepest and most extensively developed hardrock mines in North America. The mine is divided into five divisions which produce a total of 1.7 million metric tons of ore per year. In the past, labor intensive mining methods such as open cut-and-fill, shrinkage, and timber stoping were utilized. In recent years there has been an extensive change to the more productive methods including Vertical Crater Retreat and Mechanized Cut-and-Fill. Also, the percentage of production from the lower divisions below the 4850 level is increasing while upper level reserves are beginning to decline. Combined, these factors have strained the ventilation resources to the limit. By early 1984 it became clear that future production trends would require a detailed study of future ventilation resources. By November of 1984 the Ventilation Department completed a study to project these future requirements. This paper will detail the first phase of a scheduled two phase upgrade: the installation of a new surface fan.

Jan 1, 1987

By Eugie Kabwe

The increase in depth of mines due to the depletion of surface deposits leads to unsafe tunnel construction and overall ore extraction. This is due to tunnel instability associated with the surrounding rock mass’s ability to exhibit creep that occurs over time. However, the explicit description of this mechanism using conventional constitutive models has proven to be difficult and inadequate. Hence, this paper presents an integrated viscoelastic viscoplastic visco-damage model with the Duvaut-Lions function. The presented model is calibrated by experimental data to determine the viscoelastic viscoplastic and visco-damage parameters. It is further implemented in a finite volume numerical code and verified on an experimental scale by numerical modeling of a cylindrical specimen. It describes the 3-phase creep mechanism perfectly as compared to the inbuilt conventional integer-order derivative model. Results from the conducted verification show that it can successfully be employed to describe the long-term behavior associated with the creep mechanism.

May 16, 2021

The ability to track miners and communicate with them while they work in underground coal mines is important during normal daily operations, and critical in emergency conditions. As was evident during recent incidents at underground coal mines worldwide, communication with miners and the knowledge of their location is of great importance for rescue efforts and the preservation of life. Numerous technologies have been developed, adapted, and deployed to meet tracking requirements of the Mine Improvement and New Emergency Response (MINER) Act. Evaluating the performance of these systems has proven to be difficult for mine operators, system manufacturers, and regulatory agencies. The MINER Act of 2006 requires operators to improve accident preparedness by developing an emergency response plan specific to each mine. With the recent implementation of the provisions of the MINER Act of 2006, all underground coal mines in the United States are subject to the mandates of legislation concerning communication and tracking system installation. As of June 2011, 203 new or revised tracking and/or communication systems had been approved by the Mine Safety and Health Administration (MSHA), with nearly 50 other systems or revisions in the approval process (MSHA, 2011). At that time, the available approved systems for underground coal mine use included these types: ? Leaky Feeder Communication Systems ? Fixed Node-Based Communications and/or Tracking Systems ? Wireless Node-Based Communications and/or Tracking Systems ? Medium Frequency (MF) Communication Systems ? Communication System Peripherals Other types of tracking systems have since been developed and some manufacturers are seeking approval for use in this application. Some of the new products include Through-the-Earth (TTE) systems and various radio frequency (RF) adaptations. New technologies that are currently being developed and deployed in other industrial applications should also be considered, including acoustical, optical, inertial, and hybrid technologies To date, no uniform method has been employed in the industry to effectively compare and evaluate the performance of installed systems. Neither industry operators nor regulatory agencies can accurately assess the capabilities of installed systems in the continuously changing mine environment. There is need for a uniform evaluation method that provides the ability to assess how different systems and technologies perform in various mining applications, and whether they can satisfy the regulatory requirements.

Feb 23, 2014

By V. O. Tenorio, J. Puell

"Dump design is critical to effective mine planning in large scale open pit mines. Capital and haulage costs are considerable from early stages and through the life-of-mine as these dumps gradually become immense structures. Delivered mining rates, as well as certain spatial and physical constraints, provide a set of parameters of mathematical and economic relationship that creates opportunities for modeling and thus facilitates the measuring and optimization of ultimate dump design by using programming and empirical techniques while achieving economic objectives. This paper presents a methodology to optimize the ultimate dump design by minimizing its total dumping costs. The methodology consists of the formulation of a generalized model based on the relationship of the main dump parameters, followed by the use of linear programming to find the solution that minimizes the haulage total cost, and finally through a series of iterations, modifies the preliminary solution by projecting it to the topography and creating the ultimate dump design. A case study applied to a waste dump exemplifies this methodology. INTRODUCTION Open pit mine operations move large amounts of material on a daily basis from the shovel faces to the appropriate destination points. Hustrulid et al. identified three major destination places where the material receives downstream treatment after its delivery: mill processing, leaching dumps, and waste rock dumps [1]. The corresponding destination is given by a cut-off grade criteria, ore type, and the possibility of obtaining the maximum metal recovery. Dump leaching technologies have developed substantially since 1975 [2], and have enabled mining facilities to beneficiate low grade sulfide and oxide ores. As a consequence, the number of active dumps have increased since then and the entire mine configuration, which is limited in itself, has changed. The proper location, design, and construction of a mine dump must serve the safety, environmental and economic goals of the long-range mine plans. Therefore, an optimized use of the available surface area in the mine is highly desired."

Jan 1, 2018

By J. Mark Richardson

Modern mining operations are increasingly affected by complex economic factors. Broad and rapid fluctuations in metal prices, rising operating costs, socio-political trends and the inherent technical difficulties encountered in most operations, all can combine to quickly change once-profitable ventures into money-losing propositions. Accurate knowledge of metal inventories during all phases of an operation has become essential to wise management decision-making. This paper reviews key elements of metallurgical accounting: sampling theory, measurement technology and computerized data adjustment. Application of current technology to the reconciliation of a hypothetical operation is discussed.

Jan 1, 1991

By Arash Nikvar-Hassani, Lianyang Zhang

To address the drawbacks of the conventional portland cement/fly ash (PC/FA)–based cementitious material currently used in practice to construct pumpable roof supports (PRSs), a novel cementitious material has been developed based on geopolymerization technology. The novel cementitious material is comprised of two pumpable grout streams: Stream 1 is a slurry composed of pozzolanic material and high-calcium additive and stream 2 is an alkaline solution comprised of a gelling agent. Biopolymer has been added to the second stream to provide ductility to the geopolymer cementitious material. In the laboratory scale, systematic experiments have been carried out to investigate the viscosity, setting time, and uniaxial compressive strength (UCS) of the new cementitious material and develop the right recipe for field applications. By collaborating with industry and the National Institute for Occupational Safety and Health (NIOSH), full-scale PRSs have been constructed and tested. The results show that (1) the novel cementitious material based PRSs has much higher peak UCS and similar or higher residual strength than the conventional PC/FA-based PRSs; and (2) unlike the PC/FAbased cementitious material, the novel cementitious material shows good long-term durability with nocracking/disintegration when exposed to air.

Jul 1, 2023

By A. Navarra, F. Mucciardi, H. Marambio, R. Parra, F. Oyarzún

"Discrete event simulation (DES) is an appropriate framework for the plant-wide analysis of copper smelters. These smelters apply a common set of chemical reactions: copper-iron sulfides are blasted with oxygen-enriched air, sending the iron into a slag phase and the sulfur into the offgas. Moreover, conventional copper smelters exhibit similar operational dynamics: a smelting furnace operates continually, feeding into an alternating set of converters that produce batches of blister copper. The thermochemical and operational commonalities of copper smelters are integrated within the DES framework. This serves as a common basis to begin evaluating the system dynamics of individual smelters. For complex problems, the simulation framework should be developed in phases, incorporating feedback from different personnel who have complementary perspectives. Sample computations are provided in this paper based on the Hernán Videla Lira smelter, whose production is constrained by meteorological conditions. IntroductionWorld copper production is approximately 18.5 million t/y (Brininstool, 2015), worth $80 billion a year. Out of this total, 75 percent comes from the pyrometallurgical processing of sulfide minerals (Fig. 1), which occurs in copper smelters. The remaining 25 percent is from the hydrometallurgical treatment of oxides and complex ores (Rotuska and Chmielewski, 2008), which uses solvent extraction and electrowinning.The current paper describes the pyrometallurgical processing, recognizing that the underlying thermodynamics and kinetics are well known (Degterov and Pelton, 1999), with the notable exception of minor element transport, such as arsenic (As), antimony (Sb), bismuth (Bi), silver (Ag), gold (Au). The latter is an ongoing area of research, as smelters are faced with increasingly complex ores (Devia, Wilkomirsky and Parra, 2012; Swinbourne and Kho, 2012). This paper focuses on the system dynamics of copper smelter operations, which has received considerably less attention than the chemical thermodynamics and kinetics.Smelter engineers and managers may contribute to the sustainability of their plant by improving their understanding of operational system dynamics. Indeed, we have prompted smelter improvement projects (Navarra, 2016; Navarra et al., 2016; Navarra and Mendoza, 2013) simply by adapting methodologies that are commonly used in other sectors. These previous works incorporate principles from computer-integrated manufacturing (Groover, 2000) and theory of constraints (Dettmer, 2007), featuring the use of discrete event simulation (DES)."

Jan 1, 2017

By M. Polat

Variations in flotation rate by particle size and specific gravity have been investigated for three different bituminous coals. The flotation rates for various components were determined by separating the products of bulk flotation into size-specific gravity fractions. The effects of feed size and reagent addition on the flotation response of individual size-specific gravity fractions were evaluated.

Jan 1, 1994

By Edwin R. Phelps

Good morning ladies and gentlemen - today I am in an enviable position for two basic reasons - No. 1, since I am first on the program, the audience should start out awake because those that partied too much last night are still asleep, but in their room, not here. No. 2, since copper, iron, and mining technology are not competitive, the veracity of my statements will not be questioned. Most such meetings I attend are based on the subject of energy and the coal industry does have competition from oil, gas, hydro, and nuclear. However, to counteract this advantage I am the usual engineer with a limited vocabulary by schooling, and the remaining vocabulary almost completely eliminated due to the presence of ladies. In relation to the past of the coal industry, we have not only suffered the competition of other energy sources mentioned before, but in addition have in the last 25 to 30 years been required to meet the demands of a vastly changing market. To explain this statement, I am sure many of you can remember 30 to 40 years back when most homes were heated by coal furnaces or stoves and shudder to recall the shoveling of coal into the fire and the carrying out of ashes with the attendent manual labor dust. Now this space heating portion of our sales has almost become non-existant due to an almost universal switch from coal to natural gas, oil, and electric heating. Actual figures show a decrease from 119 million to less than 28 million tons per year in less than a twenty year span. Also, most of you can remember the coal burning steam locomotives and the tremendous volume of coal they consumed and then the very rapid change to the diesel-electric locomotives, incorporating improved large diesel engines driving D C generators and electric drive motors, which resulted in cheaper motive power. This change over was so complete that the annual tonnage of coal dropped from 125 million to less than 2 million tons in 15 years. 'Actually, now it requires some considerable interrogation and traveling to find a locomotive still operating on steam.

Jan 1, 1968

By G. R. Luster

In most current practice, the methods that are employed in technical evaluations of cement raw materials are deterministic; i.e., decisions among alternative raw mixes and alternative plant designs are reached with the aid of only "average" compositions and "representative" samples of the available raw materials. Nevertheless, cement plants are sensitive to raw-material variability, and uniformly high-quality raw materials are not so abundant as they once were. Some simple examples will illustrate how geological techniques can be combined with geostatistical and operations-research approaches to customize mining and processing systems to deal with variable raw-material compositions.

Jan 1, 1987