Search Documents

By P. B. Altringer

The Bureau of Mines, U.S. Department of the Interior, is investigating biodegradation of cyanide as a means of decommissioning heap leach operations. Biological oxidation decreased weak acid dissociable (WAD) cyanide in process solutions1from 50 to 170 ppm down to 0.1 ppm. The tests were conducted both in trickling column reactors, using quartz as the growth surface, and in upflow columns, using activated carbon as the growth surface. In addition, exploratory tests indicated that bacteria will destroy residual cyanide in leached ore. A flowsheet has been proposed for closure of heap leach operations in which the metals processing portion of the plant, possibly the carbon adsorption columns, or a collection pond is used as a bioreactor. The cyanide in the process solution is destroyed in the bioreactor and the treated water is used to rinse residual cyanide from the spent heaps. The water is recycled until the effluent WAD cyanide concentration meets discharge standards.

Jan 1, 1992

By Éder Domingos Oliveira, Carlos Antonio Morais, Ruberlan Gomes Silva

The objective of this study is to assess the impact of different reagents, such as limestone, lime, magnesium oxide, and sodium hydroxide, in experiments carried out in the single purification step and in two consecutive purification steps by raising the pH of a rare earth sulfuric liquor with the aim to remove or reduce the impurity concentrations in the rare earth sulfuric liquor. The choice for the best purification condition was made based on the minimum loss of rare earth elements (REEs), reagent consumption, and residue generation. The exploratory experiments show that it takes place in the two consecutive purification steps, the first one consists in dosing the limestone pulp until it reaches a pH of 3.5 followed by an addition of a lime pulp reaching a pH of 5.0. Under this condition, the results were a total removal of Fe3+, PO4 3− , and Th4+ ions and a reduction of 99%, 87%, and 37% w/w in the Al3+, UO2 2+, and SO4 2− concentrations, respectively, in the purified rare earth liquor. Furthermore, the lowest REE losses (8.3% w/w) and reagent consumption (4.3 kg/m3 ) and also a low residue generation (7.5 kg/m3 ) were observed in this condition. Despite reaching similar results regarding impurity removal, the experiments done with the addition of limestone, lime, magnesium oxide pulps, and sodium hydroxide solution in the single purification step, where the pH was raised to 5.0, presented higher REE losses (64.9%, 42.5%, 44.8%, and 60.9% w/w, respectively) and a higher residue generation (43.2, 25.1, 11.1, and 13.6 kg/m3 , respectively). This occurred due to the co-precipitation of salts containing rare earth elements in their composition. The experiments conducted with limestone, lime, and MgO resulted in a higher consumption of reagents, while the same result was observed when NaOH was used (4.3 kg/m3 ). In the experiments carried out with the addition of magnesium oxide and sodium hydroxide, the respective purified rare earth liquors presented a high concentration of magnesium, sulfate, or sodium, which could impact the quality of the marketable rare earth salts, whereas the salts obtained under the best condition observed in this study seem to be amenable for use as raw material in an attempt to obtain rare earth products with an acceptable chemical quality.

By H. C. Harrell

The Tennessee Valley Authority began employing geophysical well logging for foundation investigations in October 1973. Since that time more than 3,000 holes have been evaluated for engineering purposes. The Tennessee Valley Authority has not actively used geo-physical well logging for exploration of construction materials, but we feel that much of the information derived from geophysical logs for foundation exploration is applicable to the construction materials industry. This paper will then discuss geophysical logging as applied to foundation engineering and, by implication, the feasibility of use in construction materials exploration. The use of geophysical logging and percussion drilling instead of coring has greatly expanded TVA's data acquisition capabilities and has also resulted in substantial savings in time and money. Economical boreholes are obtained through the use of large percussion track drills (Figure 1). This equipment is capable of drilling through the overburden, setting steel casing on the top of rock, and drilling the rock beneath the casing. Holes as deep as 400 feet (121.9 m) have been drilled by this method.

Jan 1, 1977

By T. W. Camm

The Bureau of Mines conducts studies of the economic impacts of regulations on federal lands. These studies are part of the Bureau Potential Supply Analysis (PSA) program. To meet the needs of these studies, a methodology was developed to estimate operating and capital costs for a mineral deposit given its tonnage, grade, and depth. The format for the cost models in this study was developed at the Bureau's Western Field Operations Center (WFOC), Spokane, W. A., for studies of known and undiscovered resources on Federal lands. These cost models are described in a Bureau publication by Camm (1991).

Jan 1, 1993

By Xiaohong He, Qing Yu, Kaixiang Zhang, Rui Guo, Minghua Lin, Haoyu Miao

With the increasing depth of coal mining, the coal mine shaft traverses’ strata conditions become more and more complex. Shafts are often located in deep thick strata with unstable aquifers, and coal mining requires short-term rapid drainage of aquifers; the additional stress caused by aquifer water drainage is the direct cause of the shaft-lining failure. Over the years, many experts have conducted research on the shaft-lining damage caused by the consolidation and subsidence of the soil layer induced by the long-term drainage of the aquifer. On this basis, this paper conducts an in-depth study of the dynamic change of the pore water pressure of the aquifer in the short-term drainage and its influence on the response of shaft-lining strain and surface subsidence. The result shows that the Mandel effect of pore water pressure around the shaft-lining is obvious at the beginning of drainage, and the pore water pressure suddenly increases; the increase is independent of the drainage rate, which leads to the sudden increase of the shaft-lining strain value unrelated to the drainage rate. The result also shows that with the gradual dissipation of pore water pressure, the increase of shaft-lining strain is positively related to the drainage rate and negatively related to the drainage distance, and the variation trend of horizontal strain is greater than that of vertical strain, which appoints the main cause of shaft-lining damage.

Mar 16, 2023

By Gordon M. Pugh, David G. Rasmussen

INTRODUCTION Sublevel long-hole stoping is a large tonnage stoping method that may be used when there is a fairly com¬petent straight vein and the walls will stand with little support. It is a method that lends itself to a high degree of mechanization. Two variations of the method are illustrated in Figs. 1 and 2. Fig. 1 illustrates development typical for a 3-m (10-ft) wide vein. Initial development is by a lower haulageway, which may be either track or trackless. A two-compartment raise is driven in the footwall of the vein. At about 12 m (40 ft) above the main head¬ing, a footwall scram is driven and pockets through the vein are cut on 7.6-m (25-ft) centers. Each of the sub¬level blocks selected in this example is 45.7 m (150 ft) long by 12 m (40 ft) high. Stoping starts at the slot raises at stope endlines and retreats to the timbered raise. This retreat sequence starts on the lowest sublevel and the opening cut is blasted into the slot raise. This retreating system is used in order to provide a good safe back over the miners working in any given sublevel. A crawler-mounted down-the-hole or conventional pneumatic drill puts the holes down from one sublevel to the next on any desired drill pattern. Gravity flow brings the broken ore down to the scram level. The illustration shows a large slusher mounted at the timbered raise and slushing from the pockets back to the raise chute. Development of the ore block in Fig. 2 is typical for a 5.5-m (18-ft) wide vein. Initial development is by a trackless heading driven in the footwall of the vein. Pockets are then put into and through the vein on 7.6-m (25-ft) centers. For ease in using trackless rubber tired mucking equipment, these pockets are crosscut to the vein at approximately 1.04 rad (60°) rather than per¬pendicular. A two-compartment timbered raise is driven down from one level to the next. Endline slot raises are again put through from level to level. Each of the sub¬level blocks selected in this example is 40-m (130 ft) long by 33.5 m (110 ft) high. Stoping starts at the slot raises and retreats back to the timbered raise. Long holes are drilled from one sub¬level down to the next by starting between the lowest pair of sublevels and then working up the ore block. Mucking out of the pocket drawpoints is accomplished by rubber-tired load-haul-dump (LHD) units which then dump into a centrally located orepass.

Jan 1, 1982

By M. C. Rockwell

There are about 1.8 Mt (2 million st) of discarded dolomitic-limestone tailings from the Gays River lead/zinc mining operation in Nova Scotia currently stockpiled in a tailings pond at the mill site. Neutralization effectiveness similar to an agricultural grade limestone and low contents of residual metals make the tailings a potential source of soil conditioner material for the local market. However, the fine particle size, 98% passing 147 pm (about 100 mesh), and a moisture content of 20% make their handling, shipping, and application to soils difficult. The tailings were agglomerated into small hard pellets with various amounts of soil nutrients, moisture content less than 13%, and pH values ranging from 6.5 to 8.7.

Jan 1, 1987

By Yi Luo, FENGLIANG WU

Explosions and fires originated from longwall gob due to the formation of methane-air mixture have been a severe threat to coal miner’s lives.Many numerical studies on coalmine fire and explosion hazards have focused on the airflow in roadways and mine gobs. However, most of these studies isolate the gob from its surrounding roadways, and the network analysis and the CFD method are applied independently tomodel the two classes of airflows. This approach greatly limits the ability of simulatingmine ventilation flow, especially unable to consider the effects of gob boundary conditions on air exchange between the gob and the surrounding airways. An innovative finite tube method (FTM) is developed to couple the one-dimensional mine ventilation network (MVN) and the 2D/3D gob flow field (GFF). In FTM, GFF is discretized into a finite number of flow tubes each of which is formed by any two adjacent stream lines. These tubes, representing the gob’s field flow, connect the MVN into a new coupling network. To solve the coupling model betweenMVN and GFF, an iterative solution technique is developed inwhich the MVN analysis is used to evaluate the boundary pressures for GFF simulation and in turn the FTM feeds the GFF results back to the coupling network. Based on the FTM approach, a model for gas migration in gob has been established for delineating the hazard zones of explosive methane concentration and spontaneous combustion. A computer program is developed to implement the FTM simulation. An illustrative example with five flow tubes representing the GFF is created to verify the stability and convergence of the FTM solution process. A simulation example also indicates that the accuracy of FTM is improved by 12% compared with previous method. Results of an application case show that the program is capable of quantitatively evaluating the gob’s risk zones prone for spontaneous combustion and gas explosion as well as performing risk analysis for various ventilation scenarios.

Jul 10, 2020

By Earle Faig

Earle Faig Along with other transportation modes, the barge industry will be greatly affected by trends in domestic coal production. Traditionally, coal has been one of the major commodities moved by barge. Now, because of events in the international energy market, coal is finally getting the recognition it deserves as a major component of the country's energy program. Perhaps even more significantly, a series of events has caused other countries to turn to the United States as a source of coal. Although the outlook for coal demand is optimistic, it will be greatly influenced by the ability of the transportation sector to handle the additional traffic. Because of its long experience in moving large quantities of coal, the barging industry is in an excellent position to capitalize on coal's increased popularity. A brief description of the barging industry should facilitate the discussion of coal as it relates to that industry. Barge companies operate on a river system that is over 40 Mm (25,000 miles) long. It includes the East and West Coasts and the Mississippi River System comprised by the Allegheny, Monongahela, Kanawha, Ohio, Illinois, Missouri, Tennessee, Cumberland, Arkansas, Warrior-Tombigbee, and Mobile Rivers, and some smaller tributaries. The Gulf Intracoastal Waterway stretching along the Gulf Coast from Brownsville, TX, to Apalachicola, FL, also is considered part of the inland waterway system. Approximately 1,800 companies operate on the inland river system and have a combined fleet of about 4,400 towboats and 28,000 barges. The fleet of towboats represents 4.8 GW (6.4 million hp) of power. The towboats comprising this fleet vary in size from a small harbor boat to a large line haul boat with 7.5 MW (10,000 hp) of power. The choice of size and power of the boat depends on a number of factors, including the size of the river and operational constraints, such as lock size, river-current rate, and water level. The choice also depends on the tow size. A single tow on a river capable of locking through 15 barges at a time handles up to almost 20 kt (22,000 st), whereas a tow on the lower Mississippi, which has no locks, can accommodate up to 41 kt (45,000 st) of cargo. Because the quality of coal is not typically damaged by exposure to the elements, it is usually moved in open hopper barges, although covered barges are used occasionally. The most frequently used size is the jumbo barge that measures 59 m (195 ft) long by 11 m (35 ft) wide by 4 m (12 ft) deep and can handle up to 1.4 kt (1,500 st) of coal. Advantages of Barge Transportation Barging offers several inherent advantages in transportation of bulk commodities like coal. First, barges can carry large quantities of product. A single jumbo hopper barge can handle 1.4 kt (1,500 st) of cargo while it takes 15 91-t (100-st) capacity rail cars or 57 trucks hauling 24 t (26 st) each to move an equivalent amount of cargo. Thus, barges can move more tonnage with less equipment than competing forms of transportation. Second, barging offers the most fuel efficient means of transportation. Less energy is required to push a load over water than to pull a similar load over land. The amount of pollution attributable to barge traffic is minimal because barges consume less fuel. Third, barging is an inexpensive form of transportation. The inland waterway industry transports about 12% of the nation's freight for about 2% of the total freight bill. This can be attributed to competition between the large number of companies on the river system and competition with other transportation modes. Fourth, barging is an environmentally safe method of transportation. Inland river routes expose fewer urban areas to hazardous substances than rail or truck. And barge spills occur less frequently than rail or truck spills. The industry does pose some disadvantages. The waterway system is constrained by the natural river network, so barges cannot travel on the most direct straight-line route. This means that barging is usually an incomplete form of transportation requiring interface with truck or rail. The industry's market is limited to those geographical areas that are located on or near the rivers. In addition, it is a time-consuming transportation mode, making it impractical for many types of commodities.

Jan 10, 1982

By Peter Zhang, Mark Van Dyke, Ted Klemetti, Morgan Sears

Room-and-pillar mining is a mining method used in the United States to extract coal from underground, and pillar recovery is widely practiced for maximizing coal recovery and mining economics. Under certain conditions, room-and-pillar mining can create high stresses in coal pillars resulting in a coal outburst. These outbursts represent one of the more severe safety hazards in underground coal mines, potentially causing injuries and fatalities. Over the past ten years, coal outbursts have resulted in three fatalities in U.S. room-and-pillar mines. Though coal outbursts generally occur under deep cover, they are more likely to occur during pillar recovery and under multiple-seam mining conditions. Coal outbursts are generally associated with strong roof and floor and heavy loading of coal pillars, but it is difficult to predict whether, where, and when they will occur. In this respect, risk management provides a proactive tool to prevent coal outbursts in room-and-pillar mining by identifying mining areas with high risk of outburst and mitigating the risk accordingly.

Apr 26, 2022

By D. Tahija

"Carbonic acid prepared on-site from carbon dioxide gas is widely used in water treatment and increasingly in some industrial applications. It has not seen extensive use in mineral processing but is an attractive alternative to sulphuric acid for pH control, with the need to counteract high pH levels caused by cemented backfill of particular interest. The fundamental chemistry of carbonate solutions as applied to flotation and flocculation circuits is described as well as plant-scale application. A project to introduce use of carbon dioxide for pH control at the Hecla Greens Creek lead-zinc-silver-gold operation is planned to begin operation in the first half of 2015. INTRODUCTION Flotation pH Control and Backfill Most sulphide flotation circuits are run at pH values ranging from slightly acid to strongly basic, with slightly basic pH the most common. Lead sulphide circuits are typically run at values from 7.5 to 9, with zinc circuits running at higher values of 9.5 to 10.5. This has been the case with ores that produce a natural pH in the circumneutral range, so that the pH needs to be raised. Although lime [Ca(OH)2] is the cheapest reagent in use to raise pH, soda ash (Na2CO3) or caustic soda (NaOH) are also employed where sodium ions in solution are preferred to dissolved calcium, or, in the case of soda ash, the presence of carbonate is desired. The use of soda ash for pH control in lead circuits has been widely recommended for many decades (1). The situation is necessarily different at operations where cemented backfill is used in underground mines (2). Backfill, whether emplaced as rammed paste or pumped slurry, is composed of mill tailings mixed with around 10% Portland or similar cement. When later mining occurs near or adjacent to previously backfilled areas, a considerable amount of old backfill is inevitably mixed with new ore and shipped to the mill. Depending on orebody geometry, mining methods etc., the amount of backfill in mill feed can easily approach 20%, with periods of higher content not unheard of. The presence of so much backfill, with its high cement content, produces results largely indistinguishable from adding a large amount of lime to run-of-mine feed: mill pH in the grinding circuits can range above 11 and high concentrations of calcium ions are present. The need to raise pH disappears; the problem becomes to lower it."

Jan 1, 2015

By N. S. Margaris

The vegetation of Mediterranean ecosystems is distinguished by its resistance to adverse environmental conditions, and that is the reason for examining the possibility of growing species of this flora in waste disposal sites (WDSs). The survival and growth of vegetation established at a waste disposal site is dependent to a large extent on the qualitative and quantitative characteristics of the material used in the final soil cover. In the Ano Liossia WDS, where extensive remediation work is under way, three areas were examined, which met certain criteria in relation to the age of the underlying waste and the existence of impermeable material in the final soil cover. Laboratory analyses have determined soil parameters and nutrient and heavy metal content. Alongside this, at all three sites a network has been installed to monitor the qualitative characteristics of the gaseous phase of the soil cover material. The results showed the existence of a soil material containing few nutrients and the prevalence of oxygen-poor conditions, accompanied by large concentrations of CH4, CO2 and H2S, at depths of up to about one meter.

Jan 1, 2002

By Ali Ekrem Aritan

Exposure to hand-arm vibration (HAV) among the labor force in the mining industry can result in permanent vibration diseases such as behavioral disorders, visual impairment, osteoporosis, pain (mostly in the hands, wrists, and shoulders), circulatory system disorders, and malnutrition. In this study, the vibration exposure of excavator operators working regularly in 25 different natural stone quarries was measured. In addition, the relationship between vibration exposure and rock properties was investigated. Gloved and ungloved vibration measurements were performed and revealed that antivibration gloves reduce excavator operators’ vibration exposure by 7.10–25.95%. Samples from each quarry were characterized with rock mechanics tests. The correlations between the hand-arm vibration measurements and the natural stone physical–mechanical properties (uniaxial compressive strength, Shore hardness, Knoop hardness, apparent density and total porosity) were determined to be over 70%. One finding of the study was that the health risk in excavators cannot be reduced sufficiently by the sole use of antivibration gloves. Furthermore, the excavation of any rock with a Knoop hardness above 121 is associated with an 81% risk of HAV. To increase awareness of the danger of vibration exposure for natural stone miners, training programs should be provided, and technical and operational changes should be implemented.

By J. V. Thompson

The Powderhorn complex as a source of perovskite (calcium titanate) containing about 1.5% rare earths has been examined in several recent feasibility studies. Much promising exploration and process research has been done in recent years. This paper is presented with cautious optimism and with the acknowledgment that there may be some technical and economic areas yet to be explored. The Powderhorn carbonatite and alkalic stock in Gunnison County, Colorado, lies about 203 airlines km southwest of Denver at an elevation of 2450 to 2750 m (see Figures land 2). All of the mineable ore bodies are owned by Buttes Resources Company of Houston, Texas.

Jan 1, 1990

By Joseph P. Nugent

The new combination gypsum plaster and gypsum wallboard plant of Compania Industrial Kaiser S.A., the first of its kind in Mexico went into production in April of 1969. This was approximately fourteen months from the signing of the formal order for the plant and equipment. Compania Industrial Kaiser S.A. is an affiliate of the Kaiser Gypsum Company in the United States and will market practically the same line of products and to the same standards as those produced in American plants. Located in the City of Puebla, the plant will readily service the major Mexican sales areas. It is approximately 85 miles away from Mexico City on a modern, four-lane, divided highway and distribution to other major consumer areas can be readily effected by the use of a good highway system, as well as, by rail. This, plant is the, sixteenth Gypsum Wallboard Mill supplied abroad by my company, United States Wallboard Machinery Company. Other installations are in Australia, New Zealand, Chile, England, Scotland, Ireland, Finland, South Africa, Latvia and Germany. Two new mills are on order; a small unit for Brazil and a comparatively large unit for New Zealand. All these mills have one thing in common with plants in the United States and Canada; they are equipped with standard, time-proven and tested equipment and they are designed in accor¬dance with the latest engineering thinking in order to produce efficiently, the highest quality product at lowest cost. They differ generally in the size of plant, the factors that brought them into being and in the market that they supply. I believe that these differences will be of interest to you.

Jan 1, 1969

By B. Li

"Sepiolite is a magnesium-rich, porous, and fibrous clay mineral with broad applications. These applications take advantage of sepiolite’s high specific surface area and unique nano-sized channel structure. Over the past years, numerous materials and techniques based on the structure and property of sepiolite have been developed. This article reviewed the recent achievements in developments and applications of sepiolite in environmental protection, catalysis area, and nanocomposites. The prospectives of sepiolite applications is also discussed. INTRODUCTION Sepiolite is a magnesium-rich, porous, and fibrous clay mineral. The typical chemical formula of sepiolite is Si12Mg8O30[OH]4[OH2]4·8H2O [1]. Sepiolite has a high specific surface area and nano-sized channels because of its special structure [2]. This unusual crystal structure projected onto the [001] plane is shown in Fig.1 [3]. As it can be seen, silicon and oxygen atoms make up for the tetrahedral structure and magnesium and oxygen atoms form octahedral structure, respectively. Those tetrahedral-octahedral-tetrahedral ribbons expand boundlessly in one direction, leading to the special fibrous structure of the sepiolite. Every tetrahedral-octahedral-tetrahedral ribbon is combined to the next by an inverted Si–O–Si bond, which causes an interlaced layer with a continuous tetrahedral sheet and a discontinuous octahedral sheet. Terminal MgO at the edges of the ribbons is coordinated with two structural water molecules, which can form hydrogen bonds with zeolitic water molecules that are located in the channels running parallel to the fiber axis [3,4]. The Mg2+ ions inside the channels can be exchanged with other cations in solution. Therefore, sepiolite can be used to remove metal cations from aqueous solutions [5,6].It can be seen from Figure. 1 and Table 1 [7], the unique structure endows sepiolite with a substantial surface area and nanoscale channels. Its specific surface area reaches 320 m2/g and channel dimensions up to 3.7×10.6 Å. There are three active adsorption sites on the surface of sepiolite: one is oxygen atoms of the Si-O tetrahedron. The second is the structural water molecules paired with magnesium ions at the edges of the ribbons, which can form hydrogen bond with adsorbent. The last one is the Si-OH groups due to the breaks of the Si-O-Si bonds on the surface of Si-O tetrahedron. Thus, sepiolite has strong adsorption ability which has been widely used in environmental protection. Moreover, sepiolite has many significant features such as good mechanical and thermal stability, rheological property, porous, and easily modification, making it be a hotspot in chemical and biological researches. However, with the development of technology, broader and more advanced applications of sepiolite have been carried out in recent years. In this study, the recent achievement in sepiolite applications is summarized, the further tendency is also discussed."

Jan 1, 2018

By J. Paraszczak

Water-powered jackleg rock drills, introduced recently in South African mines are reported to be more efficient, faster and more comfortable to operate than conventional pneumatic drills. A comparative testing of both drill types was performed in Quebec. Based on its results and time studies done in the mines, water-powered drilling has been reviewed with regards to drilling rates achieved, infrastructure needed, side effects, health and safety considerations. This study shows that the application of water-powered drills may help increase footage drilled and improve working environment, but under specific conditions. The examples of such applications are given in the conclusions.

Jan 1, 1995

By G. M. L. Robinson

Mineral Processing Wastes, as defined by the Environmental Protection Agency (EPA), has determined that most of the mine wastes will be regulated pursuant to subtitle D (Solid Waste Regulations) of the Solid Waste Disposal Act while specific mine waste categories will be regulated within the framework of the Toxic Substance Control Act. Though EPA's determination currently relieves the industry of the regulatory constraints mandated by the Resource Conservation and Recovery Act (Hazardous Waste Regulations) Subtitle C regulatory framework; the industry is not granted immunity from historical or current environmental regulations related to listed or characteristically hazardous or solid wastes. Because of the current regulatory trends and the need to implement cost effective remediation alternatives; advanced currently available on-site remediation technologies are available to minimize, reduce, contain or prevent environmental impacts related to mining and processing activities. In light of industry technical needs, an overview of the research and commercially available remediation technologies will be discussed and a brief discussion of the strengths and weakness of each technology will be presented. Technologies to be discussed includes stabilization, solidification, soil wash, soil flush, thermal distillation, pump and treat, metal extraction, centrifuges, filter presses, bioremediation, and incineration.

Jan 1, 1992

By Richard L. Sanford

The generalized rail haulage simulator described in this paper is an outgrowth of the need to expand a previously developed single level simulator to permit analysis of production problems where intermediate car storage is used. Many of the ideas of the former single level simulator, which is an integral part of an Underground Generalized Materials Handling Simulator (UGMHS), have been used in model development. In addition, experience gained in applying the earlier model to a variety of operating conditions has been heavily relied on. The generalized rail haulage simulation model can operate as an independent system and, as such, can be used to analyze rail haulage systems using production distributions as data input. In addition, this model is designed to replace the present rail haulage sub-assembly in the UGMHS model and the linking procedure has been integrated into the model. The flow of coal from production sections in UGMHS, for example, fill the mine cars and a condition of no empty cars at a loading station will shut down in by production systems.

Jan 1, 1974

By Valeh Aghazadeh, Shima Barakan, Mina Soleymani, Ehsan Bidari, Morovvat Faridazad

Molybdenite is the most important molybdenum concentrate, which is mainly recovered as a by-product from porphyry copper deposits. Due to the low efficiency of purification processes such as flotation in the reduction of copper content of molybdenum concentrate to a standard level (i.e., less than 0.5 wt.%), further purification by a hydrometallurgical method is required. Although different types of chemical reagents were found to be effective in the leaching of copper minerals from molybdenum concentrate, the mechanisms of these processes remain largely unexplored. In this study, optimal conditions for maximum copper leaching (> 99%) were obtained at the concentration of HCl = 1 M, FeCl3 = 0.5 M, CuCl2 = 0.05 M, CaCl2 = 0.5 M at 75 °C, 500 rpm, and S:L = 1:10 during 60 min. CuCl2 was identified as the most effective leaching reagent for copper dissolution in agreement with Visual MINTEQ model results due to the formation of various types of copper chloride complexes. Furthermore, the electrochemical behaviors of FeCl3, CuCl2, and CaCl2 reagents before and after the leaching process were investigated by the cyclic voltammetry technique. The results of cyclic voltammograms at different scan rates verified the presence of copper chloride complexes, and ferric ions as the oxidizing reagents for better dissolution of copper sulfides. Based on kinetic study results of shrinking core models, both chemical and diffusion reactions controlled the copper leaching process with an obtained activation energy of 33.56 kJ/mol. For recovery of the leached copper, the precipitation process was done by the addition of Na2S at 45 °C, S/Cu = 1, and pH = 9.

Dec 26, 2022