Search Documents

By Keith A. Heasley

At this point in time, approximately 800 M tonnes (880 M tons) of coal are mined each year in the United States. Forty percent of this coal or approximately 320 M tonnes (350 M tons) is taken from underground coal mines, and from this subtotal 16% or 50 M tonnes (55 M tons) is from longwall panels (1). If, for the sake of argument, an aver- age extraction thickness of 1.5 m (5 ft), an aver- age extraction ratio of 50 percent and an in situ density of 1360 kg/ms (85 lb/ft3) for this coal are assumed, then the 320 M tonnes (350 M tons) of underground coal translates to over 310 km2 (76,000 acres) that is undermined each year. Con- sidering that the total U.S. production of under- ground longwall coal to date is approximately 345 M tonnes (380 M tons), then a total of approximately 165 km2 (41,000 acres) (considering 100% extraction) has been directly undermined by longwall coal production in the United States. If the angle-of- draw is considered, the total area affected by longwall subsidence in the United States is probably twice the above value or 330 km2 (82,000 acres) . In the future, a number of other miscellaneous factors seem likely to multiply the number of potentially damaging situations that occur due to longwall coal mining. First, the overall production of coal in the United States is expected to gradually increase. This factor is further com- pounded by both the fact that the percentage of the overall production due to underground mining is bound to increase, since the vast majority of U.S. reserves (68%) are only recoverable by underground methods, and the fact that the percentage of the underground production of coal that is recovered by longwall mining is drastically increasing (1). Finally, as the nicest underground reserves are depleted, the remaining reserves will tend to be deeper, which increases the affected surface area, and under denser population concentrations, which increases the likelihood and severity of possible damages. Overall, considering the number of factor which are biased towards increasing the amount of undermined acreage, it appears that there must certainly be a corresponding increase in the number of possible damaging situations due to longwall-induced, ground subsidence.

Jan 1, 1986

By Perry M. Jones

An important operational and environ-mental concern associated with in situ leaching activity is the balance between solution injection and recovery. Solution balance is an important indicator of the capability of a particular in situ hydrologic design to efficiently and effectively control and distribute leach solution within the target ore zone. The Bureau of Mines is investigating the factors that affect solution balance in an unsaturated ore deposit, as part of ongoing in situ leaching hydrologic investigations at the Cyprus Casa Grande Mine. Flow conditions in 58 injection and recovery wells at the Casa Grande In Situ Leaching Test Facility were monitored daily over an 18 month period. Changes in the balance between injection and recovery occurring during this period were evaluated using analytical and statistical methods. The results permit estimation of solution distribution and the volume of solution stored in microfractures and interstitial pore spaces within the deposit following 18 months of leaching. Approximately half of the difference between well injection and well recovery can be accounted for by solution movement through macrofractures into nearby drifts. Estimates of solution storage within the ore deposit at the end of 18 months of leaching range from 3.5 to 6.9 pet. of injected solution. These results also suggest that 13 to 26 pet. of the fracture/interstitial pore space in the deposit was saturated with solution after 18 months of leaching.

Jan 1, 1991

By A. D. MacPhail

The Highland Valley Copper partnership was formed in July 1986 and was the logical result of a mine with a large ore reserve but no adequate mill, and a mine with a large, modem mill but dwindling ore reserves. The original partners -Cominco and Lornex -were joined in January 1988 by Highmont Mining Co. which contributed a two-line concentrator. During 1988/1989, the Highmont mill was moved 7.5 km to adjoin the Lornex mill, forming what is now called the Highland mill, with a current nominal capacity of 130 000 tonnes per day. The mine is located 220 km northeast of Vancouver, British Columbia and is close to four communities in which personnel make their home: Logan Lake, Merritt, Ashcroft, and Kamloops. The map in Figure 1 2.2 shows the general area. Kamloops is a major service centre and is serviced by two railways, two major roads and a regional airport.

Jan 1, 1993

By S. A. McGhee

ASARCO Incorporated embarked on a modernization and expansion program to improve overall operating efficiencies and to more effectively develop the large mineral reserve at the Ray Complex Open-Pit Mining operation located near Kearny, Arizona. Major elements of this Ray Modernization and Concentrator Expansion Project included engineering and construction of a 54,400 MTPD (60,000 STPD) In-Pit Crusher and Overland Conveying System. and a 24,200 MTPD (30,000 STPD) Copper SAG Concentrator and Tailings Disposal System. Detailed engineering, procurement, and construction management were initiated in November 1989 under contract with Bechtel Corporation. Field construction commenced in May 1990 leading to mechanical completion and start-up during February 1992.

Jan 1, 1993

By N. C. Miller

In situ stope leaching is an innovative mining system that reduces the surface impacts of conventional underground mining. As in any leaching operation, stope leaching requires hydrologic site characterization and control of leaching solutions. Several tracer tests, using sodium chloride (NaCl) in various concentrations, were conducted by the U. S. Bureau of Mines (USBM) in an underground experimental stope to simulate a leaching environment. The tests were conducted in fractured crystalline rock that was partially saturated. As tests progressed, the surrounding fractures became more saturated. A predominant flow direction away from the stope was found during testing. Testing procedures, preliminary results, and remediation ideas based on field observations are presented in this paper.

Jan 1, 1995

By T. Kelly

The Cannon Mine is located in Chelan County, near Wenatchee, Washington, at the eastern foot of the Cascade Mountains. The mine is situated about two miles from the Columbia River, in the arid Columbia River Valley. Two hydroelectric dams provide electricity for the area, the Burlington Northern Railroad has a switch yard and loading facilities in Wenatchee. Approximately 25,000 people live in the area. The principal industry is fruit farming. Underground mining techniques are used to provide feed for a 2,000 tpd flotation concentrator at the site. The techniques are low- cost, high productivity methods which allow for a high extraction rate along with a high rate of recovery of the minable reserve.

Jan 1, 1986

By J. W. Hawkins, K. B. C. Brady, M. W. Smith

The Pennsylvania Department of Environmental Protection (PaDEP) has been issuing surface mining permits since 1984 that authorize remining in areas that will affect preexisting pollutional discharges. These permits require the mine operator to employ best management practices to reduce pollution loading from abandoned mine discharges. A total of 110 completed mining operations with 233 discharges were evaluated to determine the impact to water quality. Overall, acid loading from these discharges was reduced by 7, 200 kg (15, 900 lbs) per day or 61%. Metal loadings were also reduced. For acidity, 49% of discharges improved or were eliminated, 52% showed no significant change and fewer than 1 % got worse. Loading reductions resulted from a combination of reduced concentrations and lower flows.

Jan 1, 2003

By Feng Liu

"With seven new applications for plans of work for exploration in the international Seabed Area approved by the Council during its twentieth session of the International Seabed Authority, 26 total approvals have been made by the Council up to date. Among them, three contracts were made with COMRA. On 8 August 2014, China Minmetals Corporation submitted another application to the Authority for approval of a plan of work for exploration for polymetallic nodules in the Area, which is also sponsored by the Government of the People’s Republic of China.China is one of the main contributors to the international seabed regime. The Presentation will describe China’s activities in the Area, such as exploration, technology development, environmental protection and policy making.JIAOLONG is a submersible with capacity of 7000 meters. JIAOLONG’s sea trials were carefully made in 4 years, from 2009 through 2012 and it successfully dove to a depth of 7062m in June 2012 at Mariana trench. A so called "Test Application Phase" started thereafter, and is planned to last for 3-4 years. Two cruises and 4 legs have already been made since then. A wide-range of findings were obtained during dives in South China Sea, and in COMRA’s Exploration Contract Areas for polymetallic nodules and cobalt-rich ferromanganese crusts. This presentation will reveal the colorful findings."

Sep 1, 2014

By Alfred W. Eustes III

The first of a series on the evaluation of rock cutting tools, this paper discusses the results of full-scale laboratory drilling tests that compare the performances of several polycrystalline diamond cutter (PDC) coring bits. The tests were performed in welded tuff as part of a site characterization program. Number of cutters, size of cutters, air course design, and other parameters were evaluated as they affect penetration rate, but this paper focuses mainly on the relationships of torque vs. thrust (weight-on-bit), specific energy vs. penetration rate, and thrust vs. penetration rate. These relationships change in diagnostic ways according to bit type, bit condition, and type of welded tuff.

Jan 1, 1998

By W. C. Goldberg

This paper presents pit slope monitoring and back-analysis case studies con-ducted to evaluate and, if possible, stabilize slopes at the Berkeley Pit in Butte, MT. Two specific slopes were studied in detail. The first slope was determined to be near limiting equilibrium, as evidenced by its response to the initiation and cessation of mining, while the second failed on three occasions. Back-analysis of the failed slope verified the laboratory-derived geomechanical properties of the earth materials. Early detection of slope movement can show a need to take action, including modifying slope geometry, dewatering if the slope were wet, and/or investigating and implementing artificial supports. Monitoring slope displacements in open-pit mines can supply data for predicting collapses and preventing serious damage, injuries, and/or loss of life.

Jan 1, 1989

By Roger M. Buckeridge, Charles D. Reese, Silvio M. Martino, William T. Carey, Ansel H. Graham

FUNCTIONS OF RAIL HAULAGE SYSTEMS The principal application of rail haulage in under¬ground mining is in the movement of ore or coal pro¬duction from near the mining areas out to a processing plant. In some cases, such production haulage may end at a shaft pocket or slope belt conveyor transfer station, depending on the type of mine and the geo¬logical placement of the mineral being mined. Main-Line Haulage The basic reasons for choosing main-line rail haul¬age are high-tonnage production per shift and long haulage distances. The choice between rail and other systems, such as belt conveyors, is not easy and requires an integrated study of many factors: tonnage, distance, grade, product size, number of producing areas, ore reserve, safety, capital cost, operational and maintenance cost, and the mining system. Projecting a main-line rail haulage system for com¬parison with other systems requires a choice of many variables which are interrelated. The project must start with consideration of the mining system, tonnages per day, distances and grades, and loading and dumping conditions. Rail mine cars of different sizes and types are studied. High tonnage demands consideration of wider track gages. A suggested minimum for metal mines is 914.4 mm (36 in.); for coal mines, 1066.8 mm (42 in.). The choice of the train size should be governed by tonnage per shift, physical factors of loading and dumping, cycle time, and the number of trains that can be operated and safely controlled. After the size of the train is determined, the type, size, and specifi¬cations of the locomotive can be selected. The loco¬motive may be trolley, battery, or diesel; selection guides are discussed elsewhere in this chapter. The advantages of rail main-line haulage are high tonnage capacity, flexibility, reliability, safety, low operational and maintenance cost, and dual usage of the system (supply haulage, for example). The dis¬advantages are high capital investment, high installation cost, the requirement for more maintenance facilities, and restriction to certain ore reserves and mine pro¬jections. Supply Haulage Supply haulage is a basic requirement of any mine, but the type and volume of supplies vary with the type of mineral being mined, the mining methods, and the size of the mine. A mine developed for rail main¬line haulage gains supply haulage through the addition of a secondary track system to extend the main line closer to the producing areas. Additional haulage equipment, generally smaller, is also added. It is neces¬sary to design into the rail system more switch bypass points and train control systems. The track system standards demanded by rail main-line haulage con¬tribute to the reliability and efficiency of the supply haulage function, whereas a supply track system to supplement other haulage systems often suffers from poorer track and installation standards. When belt conveyors are chosen for production haulage, a rail supply haulage system is often installed rather than using rubber-tired vehicles for supply haul¬age. The conditions of the seam or ore body create these items for consideration: haulage grade of more than 6% favors rubber-tired vehicles; longer haulage distances favor rail; difficulty in maintaining a smooth roadway favors rail; and movement beyond the end of a rail system generally requires rubber-tired vehicles, making a single system rather than a dual system attractive. Although operation of a supply haulage system may be concentrated on a single shift of a multiple-shift mining operation, proper planning and supervision are required if the haulage is to be efficient. Often the newer personnel at a mine are assigned to supply haul¬age which may add to the difficulty of obtaining maxi¬mum efficiency. Supply haulage by rail offers the advantages of high reliability, lower maintenance, and high efficiency over long distances. The disadvantages are less flexibility, high installation costs, and rubber-tired vehicles for use beyond the inby end of track often required. Personnel Movement The efficient and comfortable movement of the miner to and from his work area has a significant effect on his daily output. Minimizing man-trip time also becomes more and more important as hourly wages increase. Personnel are generally moved over a rail system by one of three methods: a specialized personnel carrier to which a certain number of men who work in a certain area are assigned; a combination vehicle, used to carry personnel but also capable of being used as a light supply/utility locomotive during a working shift; and man-trip cars towed by a supply locomotive. The first and second methods are used in coal mines where long distances make speed and comfort important. The third method is more common in metal mines. Equipment Movement As mining equipment technology has advanced, many mining machines and their subcomponents have grown in size. This trend requires careful planning for adding specialized carriers to handle the movement of larger equipment. Continuous miners, longwall equipment, raise borers, and ventilation equipment are examples of machines which may be difficult to move and which require special handling. The selection of the weight, speed, and operating characteristics of supply locomotives used to move equipment is important. Larger mines may often justify a special group of loco¬motives for this application.

Jan 1, 1982

By Diane Moody

I have been asked to give you the National Coal Association's (NCA) view of the future of the coal industry. However, before discussing the outlook for the future I would like to set the stage by taking a brief look at how the industry has changed over the last decade. In 1977 the coal industry was in the midst of a period of steady growth. Although most of the gains in the early and mid 1970's occurred in the west, the industry was still predominately eastern, with eastern production accounting for 76 percent of the 697 million total tons produced in 1977. The labor force was nearing a high - at over 220,000 workers, and the number of active mines was also at a decade high of over 6,000. Productivity on the other hand was at a low. The average miner produced 1.80 tons per hour, and labor relations were also at a low point. Projections for coal's future were very optimistic, mainly because of the unprecedented growth in coal use by the utility industry. In 1977 the 477 million tons of utility coal accounted for 68 percent of U.S. coal production, and the utility industry planned on 129,000 MW of new coal-fired capacity over the next decade. Consumption of metallurgical coal at coke plants was the second largest market at 78 million tons; the industrial and residential market consumed 70 million tons and exports were at 54 million tons. But in retrospect, a lot was happening in 1977 that signalled many changes in the coal industry: - Amendments to the Clean Air Act were passed, which required that utilities take an entirely different approach to meeting New Source Performance Standards at new plants, and required that standards be set for industrial boilers as well; - the Surface Mining and Reclamation Act became law; -electrical generation, despite the optimistic forecasts, was nearing the end of a period of close to five percent annual growth; -1977 ended and 1978 began with the longest coal strike in U.S. history. -crude oil imports in the U.S. reached an all time high as did both total consumption of petroleum products in the U.S. and oil consumption at utilities. The high level of oil imports set the stage for the oil price increases of 1979 and 1980 which resulted in an immediate increase in demand for coal, not only in the United States, but world wide. Labor strikes in Australia and Poland sent foreign buyers to the U.S. literally in droves, and quickly made the U.S. a force in the world steam coal market. The U.S. coal and transportation industries responded to this overwhelming potential demand for coal. In a very short time, the capability had been developed to mine and transport the 1.2 billion tons of coal that forecasters said would be needed by the mid 1980's. What was not anticipated was that the economic effects of sharply higher oil prices would dampen demand for energy, especially for electricity, as quickly as we have seen; that coal industries in other countries would respond as rapidly as the U.S. coal industry, and at a rate

Jan 1, 1988

By R. Sellaro

It has long been understood that extended occupational exposures to respirable mine dusts can lead to chronic lung disease. In underground coal mines, CWP and silicosis are major concerns. While there have been many studies aimed at understanding total dust concentrations and silica content associated with different mining conditions (e.g., locations/occupations within a mine, cutting methods, geologic strata), little research has been completed to more comprehensively characterize respirable dust (i.e., by particle composition, size distributions, shapes). This preliminary study sought to characterize dust from an underground coal mine in Central Appalachia using scanning electron microscopy with energy dispersive x-ray (SEM-EDX). Respirable dust samples were collected from various locations in the study mine, and individual dust particles were identified and classified by mineral type. A continuous personal dust monitor was also used to estimate total respirable dust concentrations during sampling. Here we report initial results of this work, and discuss advantages and challenges of particle-level characterization of mine dusts in terms of occupational health research.

Feb 23, 2014

"The Ohio River Bridge East End Crossing Tunnel requires a 75-year service life of its cast-in-place reinforced concrete lining. This twin-tube 3-lane (each tube) highway tunnel is about 55-ft wide and 30-ft high. Since unified tunnel service life prediction methodology does not exist in the US, challenges occurred during the design-build phase of this project. These challenges include the methodologies in determining the reinforced concrete’s degradation mode, the lining’s surface chloride concentration level, the reinforcing steel’s critical chloride threshold value for corrosion, how to verify the concrete’s diffusion coefficient, and the durability impact from concrete crack width. This paper presents a methodology in verifying the proposed concrete mix can achieve the service life requirements. This methodology can be adopted for service life prediction for future tunnels to be built in the US. INTRODUCTION The Ohio River Bridge East End Crossing (ORBEE) Tunnel is part of a Public Private Partnership project, which connects transportation network between Louisville, Kentucky and southern Indiana. Located in Louisville, Kentucky, the twin-tube highway tunnel provides northbound and southbound lanes of the Kentucky approach to a new bridge across the Ohio River. Tunnel lengths are approximately 1,675-ft and 1,685 for the northbound tube and the southbound tube, respectively. Connected by two cross-passages, both tubes have a roadway width of 40-ft, for 3-lane traffic, and a vertical clearance of 26.5-ft.The tunnel was constructed by drill and blast method with shotcrete and rock dowels as initial ground supports. The final tunnel lining system includes: •,Nominal 16” cast-in-place reinforced concrete lining, with 2” and 3” concrete covers over reinforcing steel for its extrados and intrados, respectively. •,20” cast-in-place reinforced concrete invert slab, with 4” and 3” concrete covers over reinforcing steel on its top face and bottom face, respectively. •,PVC waterproofing system around tunnel perimeter, excluding invert slab. •,Perforated PVC groundwater collection pipes on both sides of the tubes and one below the invert slab of each tube."

Jan 1, 2016

By C. M. Bartley

Canada has been a producer of sulphur in various forms for about 100 years, Pyrites, as a source of sulphur dioxide for the manufacture of sulphuric acid, were being mined in the 1860's. Smelter gas, for the same purpose, has been recovered since 1928. Between 1935 and 1943, and from 1952 to the present, elemental sulphur has been produced in Canada from two raw material sources and by several methods. This paper attempts to present a view of the current status of the elemental sulphur industry in Canada based on the sour gas fields of Alberta and British Columbia. Production from this source has increased rapidly in the past 12 years to make Canada one of the major sulphur producers of the world. The present industry in Canada relies mainly on sour gas sulphur and it is expected that it will continue to grow in the future. However, before describing current activity relating to sour gas it may be of interest to outline briefly the early pyrite activities, the roots of the sulphur industry in Canada.

Jan 1, 1964

By A. E. Jack Swanson, Brian P. Micke

INTRODUCTION Nevada Goldfields began underground mining development at the Kingston Project in September, 1986, followed by mill start-up in March, 1987. The first gold pour in April followed three years of preparatory work in establishing a North American operational base for the production of precious metals by Golconda Minerals N.L., an Australian mining firm. GENERAL CORPORATE BACKGROUND The Golconda Group of companies was established in early 1983 in Australia. It began operations by successfully retreating tailings at several old gold mining sites throughout Australia. With the limited reserves available for tailings retreatment, Golconda began to look toward the future by conducting a gold exploration program in Australia. However, the continued high price of gold in Australia had limited the possibilities of acquiring good properties at a reasonable cost and consideration was given to looking outside Australia in addition to Golconda's domestic exploration activities. North America was favored because of the proven potential for substantial gold deposits, the established infrastructure which would allow for rapid and cost-effective development of new projects and the advantages of similar political and economic climates. In mid-1984, Golconda established an office in California and began an extensive study of over 100 prospects throughout the United States. Two prospects were identified as a result of this study whch showed merit; one was located at Empire, Colorado and the other at Aurora, Nevada. Negotiations were then successfully undertaken to acquire these two properties. Golconda's U.S. offices were moved to Reno, Nevada in early 1985 to facilitate management of its projects. To operate and manage these projects, a small Canadian company listed on the Vancouver Stock Exchange, Cannon Minerals, was acquired by Golconda and renamed Nevada Goldfields Corporation. The current structure of the company is shown below in Figure 1. A private placement of 2,575,000 shares of common stock at US54.00 per share was arranged by Jacksons Limited of Australia in association with W.I. Carr (U.K.) Limited of London. This placement resulted in US510.3 million being available in May, 1986 for the acquisition and initial development of the Aurora and Empire projects. While the financing was underway, project planning commenced on both the Aurora and Empire projects. The Aurora project was selected as the one to be initially developed because of its relatively advanced stage of development. The

Jan 1, 1987

By P. O. Ripley

Into this tumultuous twentieth century, every second, two new babies are born. This is 5,412 per hour, and 130,000 per day. Relentlessly, consistently, alarmingly, they add to the more than three billion human beings who already inhabit the earth. Every tick of tier clock brings with it a problem child, the problem of another mouth to feed, another body to clothe, another human being for whom to provide. On the other hand, medical science has achieved a postponement of death, considerably past the period of a few years ago. Thus, life expectancy has been increased and world population has increased accordingly. Darwin (4) writing in 1962, suggests "It is curious how long the world is taking to perceive that we are living in what is a fantastically abnormal period of history, and one which must inevitably end soon, The first warning note of a possible population explosion was given by Malthus in 1799". He suggested that population increases geometrical while production increases only arithmetically and that soon we would not be able to feed the rapidly increasing population.

Jan 1, 1966

Industry and regulatory agencies have requested guidance on safe blasting near transmission pipelines. The U.S. Bureau of Mines and AMAX Coal Company have studied surface coal mine overburden blasting near four steel and one PVC pipe-line of 15 to 5l-cm diameter, monitoring vibration, strain, and pressure. Unlike tests simulating construction blasting, these were up to 1000 kg per delay in 3l-cm blastholes. Worst case comparisons showed that 12.7 cm/s blasting vibrations produced strains about 1/4 that of pressurization and 10-18 pct of the ultimate tensile strength. No failures occurred from blasting as close as 15 m which produced vibrations over 60 cm/s.

Jan 1, 1994

By J. S. Gardner

Fortunately, few mining professionals have dealt with what all mining professionals fear---a mine disaster. Unfortunately, many have dealt with ?accidents? which may or may not claim lives but nevertheless rise to the level of a ?disaster? given the fallout of liability and litigation in today?s society.1 The undersigned authors published an article some ten years ago regarding crisis management2 based upon their collective first-hand experiences in actual disasters to that point in history. Unfortunately, disasters have occurred since that time, prompting legislation, and a fresh analysis and expansion of those basic principles is certainly in order. Without question, no two disasters are ever alike, yet general guidelines for forming an effective plan of action can be formulated?and if a mining operation is to have any chance of survival after a disaster, such a plan is vital. The primary concern as any disaster evolves remains as stated a 2003 SME article3--the protection of human life. From that point, the focus moves to any assistance that may be needed given the magnitude of the situation. Permeating throughout this process is "damage control." The first step in dealing with a disaster, however, begins long before any threat of danger arises?formulation and implementation of an Emergency Response Plan.

Feb 23, 2014

By Albert Hofstra, Joel Leventhal

The gray, dark gray and black colors of the sediments and the presence of pyrite in the Carlin, Jerritt Canyon, Horse Canyon, Betze, and Gold Acres sediment-hosted disseminated gold (SHDG) deposits indicate that these rocks are not oxidized with respect to carbon and iron sulfide. Both ore and non-ore host rocks generally are dark colored. Analyses for noncarbonate carbon (usually called organic carbon) in samples from SHDG deposits and related unmineralized rocks indicate that these rocks contain from a few tenths to a few percent carbon. We use the term noncarbonate carbon because, strictly speaking, organic carbon denotes carbon that is bound to hydrogen. However, the carbon present in SHDG deposits and related rocks has very little hydrogen chemically bound to it. Rocks with less than 2% organic carbon are usually gray in color. The dark colors in our samples are due to the relatively high temperatures that these rocks have experienced relative to organic matter maturation. We confirm the results of Nelson et al. (1982) that previous reports (for example, Radtke and Scheiner, 1970) were incorrect in reporting significant amounts of humic acids, extractable hydrocarbons (bitumen) or "carbonaceous" material. We believe these reports had problems with contamination or misdirected emphasis. Our samples consisted of unweathered rocks, collected mainly from mine cuts (benches, trenches, cores) and put into glass containers or wrapped in aluminum foil to avoid contamination. Only a few samples were collected from natural outcrops. We were careful to avoid samples in proximity to blast holes that were packed with ammonium nitrate and diesel fuel ("ANFO"). Contamination by ANFO may explain some of the previous reports of hydrocarbons, pyrobitumens, humic acids and anomalous nitrogen. When we were collecting samples, it was apparent that in addition to lithologic and color differences, the surface appearance of the rocks was distinguishable: "preg robbing" material that had a sooty surface; "graphitic" rock with a shiny surface; and more ordinary rocks that had a flat gray or black appearance. [Preg robbing is a term for ores that adsorb gold from the milling circuit; the graphitic material had not been x-rayed to actually identify graphite.] We hoped that laboratory study of these samples would show some fundamental differences that we could relate to ore genesis. Even though these sample types appeared different in the field, we could not distinguish any differences in thermal maturity (see below). Normal petroleum/organic geochemical laboratory procedures (solvent extraction, Rock-eval, pyrolysis-gas chromatography) failed to yield much information because the carbon was over-mature relative to oil and gas generation. Rock-eval results show less than 20 (± 20) mg of pyrolizable hydrocarbons per gram organic carbon (and an indeterminate Tmax) indicating that the organic matter in these deposits is burned-out relative to petroleum generation [with an H/C (atomic) ratio of less than 0.41. Because of the non-definitive results from standard organic geochemical methods, x-ray diffraction (XRD) and Raman spectroscopy were used to characterize the carbon. Prior to XRD, samples were treated with HCl and HF acids (1) to remove quartz that has a peak near 26° [20] at the position of the 002 peak of graphite and (2) to concentrate the carbon to a level detectable by XRD. The residue was put on a colodion mount and analyzed by XRD. The XRD analyses yielded a broad peak at 26° [20]. The shape of this peak indicates that the carbon is more thermally mature than anthracite rank coal but less mature than crystallized graphite. Based on XRD results from the literature (Landis, 1971) that are calibrated to metamorphic facies, results from our samples correspond to pumpellyite-actinolite to lowermost greenschist facies conditions, probably

Jan 1, 1990