Search Documents

By W. K. Katoto

The Tailings Leach Plant (TLP) of the Zambia Consolidated Copper Mines Ltd at Nchanga was commissioned in 1974 as the world's first largest successfully operated agitation leach SX-EW plant for copper production. The design, development and operation of the plant soon after commissioning termed as TLP stage II has been described by Holmes et al (1). In the initial phase the plant was designed to treat approximately 25,000 tonnes per day of current flotation tailings from the Nchanga Concentrator operations, and had a design capacity to produce 75,000 tonnes per annum of copper. Further expansion took place in 1986, and TLP stage III was successfully commissioned to treat an additional 20,000 -25,000 tonnes per day of large reserves (over 135m tonnes) of reclaimed tailings stockpiled since the early 1930's in four paddock type tailings dams (T01 to T04). The salient feature of TLP stage III expansion described by S K Mwenechanya et al (2 -3) was the installation of the world's largest Horizontal Belt Filter Plant with 26 filters each of 80 m2 filtration area.

Jan 1, 1996

By M. J. Ross, D. A. Norrgran, J. A. Wernham, J. N. Orlich

INTRODUCTION Laboratory testing for magnetic concentration circuit design is a requirement, just as it is for most other types of concentration. Natural variations in raw materials allow on1 y the broadest of generalities to be made regarding magnetic separation. Further, magnetic fields are geometry dependent, leaving fundamental models of a separator overly dependent upon the exact conditions for which the models were derived. Despite this, an understanding of the basics of magnetic separation and of the problem to be attacked can result in rapid progress towards the final circuit design with a relatively simple testing program. Magnetic Separation Basic Principles A magnetic field can readily be understood in terms of lines of flux. A familiar demonstration of these lines of flux is the pattern of iron filings on a sheet of paper when a magnet is placed underneath. Lines of flux2 are measured in Gauss (1 line/cm2) or Tesla (10000 gauss). Regions of high field strength have a greater number of lines. Field direction is indicated by a convergence of lines. When a particle is placed in a magnetic field it cuts the lines of flux and alters them in one of three basic patterns. These patterns are referred to as diamagnetic, paramagnetic and ferromagnetic. Diamagnetic materials have electronic structures which react to oppose an applied magnetic field. This opposition acts to locally reduce the applied field slightly. The visualization is that lines of flux diverge and go around the particle. Because of this divergence or opposition, a diamagnetic particle will tend to move towards regions of lower flux density. That is to say that the particle will be repelled by a magnetic field. Aluminum oxide and napthalene are examples of diamagnetic materials. Paramagnetic materials have an electronic structure which increases an applied magnetic field. Although these materials also exhibit diamagnetism, they have randomly oriented impaired electrons which align with the magnetic field. The resultant local field enhancement is significantly larger than the diamagnetic opposition. The visual-

Jan 1, 1986

By V. Dentoni

The paper deals with the assessment of the visual impact generated by surface mining and quarrying. Previous research works proved the applicability of an indirect method based on the elaboration of digital images through which the extent of the visible altered area and the chromatic contrast with the surrounding environment is calculated. The resulting level of visual impact allows an objective comparison among different cases as far as the evaluation procedure is univocally defined. The article illustrates the application of the method to a number of selected quarries located within the Sardinian territory; different issues are discussed such as the choice of the viewpoints from which the pictures are taken, the influence of the distance from the quarry to the selected viewpoints, the light condition and the orientation of the quarry faces. Moreover, the visual impact level obtained from pictures taken at the same time with five digital cameras are compared in order to evaluate the contribution on the overall uncertainty.

Jan 1, 2008

By K. S. Radcliffe

Results are presented for the first phase of an experimental program to study the feasibility of using acoustic velocity for predicting the state of stress in a rock mass. Compressional wave velocities were determined axially in cylindrical samples during uniaxial compression for several rock types conditioned in dry and water-saturated environments. Results indicate that in rocks containing compressible voids or cracks, substantial velocity change occurs with the application of stress in the lower (below 100 MPa) stress regime. The effect norm- ally is nonlinear, however, and diminishes to asymptotic values when cracks or voids become closed or with saturation. Empirical prediction equations were derived for each rock type by linear and nonlinear regression analyses, and correlation coefficients were calculated to determine the equations that best fit the stress- velocity data. The operational range for predicting stress using compressional-wave velocity appears to be within the range of vertical stress expected in most shallow to intermediate depth mining operations (less than 1,000 m). Based on the experimental results to date and theoretical considerations, it appears that the technology can be advanced to predict in situ stress based on acoustic P-wave velocity determinations in most mining situations.

Jan 1, 1986

By H. Wesley Peirce

Arizona embraces portions of two major western-U.S. physiographic-geologic provinces and a smaller, local one. These exert fundamental control over the geologic framework and associated earth-material resources and potential. The Mogollon Rim diagonally crosses the State and separates the Colorado Plateau Province to the northeast from the Transition Zone and Basin and Range Province to the southwest. More than 90 percent of the population, production of nonfuel minerals, agricultural land, and water resources are in the Basin and Range part of the State. In 1981 Arizona was ranked number one in the Nation with respect to the value ($2.56 billion) of nonfuel-mineral production. About 8.2 percent of this amount ($212.9 million) can be attributed to nonmetallic (industrial) materials. Although a diversity of nonmetallic substances is produced and some are exported, the bulk is utilized within the State and is directly related to market growth. Since 1950 there has been a fourfold increase in Arizona's population, a concomitant twelvefold jump in sand-gravel production (tons), and a twentyfold increase in "stone" production. New industries developed during this time include cement, salt (and storage of liquid petroleum gas products in solution cavities in salt), zeolite, hydrofrac sand, vitrified clay pipe, crushed marble products (teed additive, pool sand, roofing granules, etc.), and "rock" wool. Most of these newer industries serve out-of-State as well as in-State markets. In 1981 at least 225 industrial mineral or rock deposits were being worked to produce about 10 tons of material per Arizona resident per year. In 1980 the relative values of basic industrial minerals produced in the State, by major group, were cement and lime (51.6 percent); gravel (26.5 percent); sand (11.8 percent); stone (4.6 percent); and others (5.5 percent). Detailed knowledge of the nonmetallic rock-and-mineral content of most Arizona ranges and basins is lacking. Exploration opportunities in this sun-belt growth region appear encouraging.

Jan 1, 1987

By A. Noble

Linear circuit analysis (LCA) is a fundamental tool which has been used to evaluate mineral separation circuits during the preliminary design phase. Traditionally, the LCA methodology uses the analytic circuit solution to determine the relative slope of the circuit?s partition curve. This value is then used as an indicative performance measure suitable for the comparison and ranking of alternative circuit configurations. Unfortunately, the partition curve slope only reflects the separation potential of middling material. In most mineral systems, this material represents a small portion of the initial feed (due to liberation) as well as a small portion of the revenue potential (due to the incremental value). Respecting these limitations, the authors have developed new separation performance indicators which may be derived from the analytical circuit solution and used in LCA problems. These indicators inherently reflect the separation potential of pure material, providing a better indication of lost revenue due to misplaced material. The complete methodology has been integrated with prior software to produce the Heuristic Optimizer for Resource Separation Economics (HORSE).

Feb 23, 2014

By Ulf B. Andersson, Christina Dahnér-Lindkvist, Bruno Figueiredo, Jessa Vatcher, Jonny Sjöberg, Joel Andersson

Hydraulic fracturing to precondition the rock mass in high seismic risk environments has great potential. Unfortunately, there are many unanswered questions about how to best implement a hydraulic fracturing program at individual mine sites, and even how to best use our engineering tools to evaluate these plans. To give the hydraulic fracturing field tests at LKAB’s Kiirunavaara Mine the best chance of success, fully-coupled, discontinuum numerical modelling Itasca’s 3DEC code was used together with statistical simulations of the fracture network. For modelling purposes, it was assumed that hydraulic fracturing successfully reduces seismic risk through 1) the creation of hydraulic fractures along a plane at each injection site, and 2) activation of existing discontinuities. A variety of scenarios for the mine were evaluated, which focused on site specific uncertainties (such as the spacing of the pre-existing discontinuities) and practical solutions (such as the hydraulic fracture spacing, selection of injection medium, and hydraulic fracture site location relative to production). The discrete fracture network (DFN) realizations were developed using available statistical data for discontinuities near where hydraulic fracturing was planned.

Apr 26, 2022

By Miguel Reyes, Chenming Zhou, MATTHEW GIRMAN

This paper is aimed at helping the mining industry to better understand the challenges posed by electromagnetic interference (EMI) and to promote electromagnetic compatibility (EMC) in underground coal mines. The paper begins with a review of EMI standards in other industries, then presents some representative examples of EMI instances that have occurred in the mining industry, followed by a literature review of published EMI research in mining and, finally, a discussion on mitigation strategies and practical considerations related to EMI in mining.

By Martin H. Stanczyk

The Organic Act of 1910 established the Bureau of Mines and gave it authority and responsibility for conducting research on separation, recovery, and recycling of waste products and scrap generated by the mineral and metals industries and the consuming public.(1)1 It was apparent to our Nation's leaders even then that mineral resources, once mined, are irreplaceable and that the development of methods for recycling the values contained in wastes would be required to solve the problem of even¬tual scarcity, Estimates of the increase in per capita consumption of mineral resources in this country indicate that the consumption of metals, minerals, and fossil fuels by 1980 will be double that consumed in 1970 (2). The United States can expect to meet its future mineral needs in three basic ways: the first is through increased production of primary raw minerals; second by increasing imports from foreign sources; and third by recycling secondary materials and metals that were formerly discarded as waste. Rather than consider these

Jan 1, 1972

By Milton Gomez, Nico Sutmoller

Low-density cellular concrete (LDCC) was first introduced to the market in the early 1900s and since then has made continuous technological advances. There are two primary types of LDCC: permeable and non-permeable. Both types of cellular concrete offer advantages in different types of geotechnical engineering applications. Because of its unique characteristics of low density, high compressive strength, and high fluidity during placement, LDCC offers an effective solution for a wide variety of engineering applications, and in many cases provides a more cost-effective, labor saving alternative to traditional fill materials. This paper will review the history, characteristics, and technological advances of LDCC, highlighting multiple real-world case studies that showcase the high-performance capabilities of both permeable and non-permeable LDCC.

Dec 1, 2022

By P. Eger

Minnesota contains a major low- grade copper-nickel sulfide resource within the Duluth Gabbro Complex. Several companies have actively explored this resource. Open pit mining would be required to develop portions of the resource, and as a result, large quantities of sulfide-bearing lean ore and waste rock would be stockpiled. Although the problems associated with high-sulfide tailings and acid mine drainage are well documented, the leaching characteristics of low-grade mineralized stockpiles must be understood for environmental impact assessment, siting, and planning. The Minnesota Department of Natural Resources and AMAX have cooperated in a research program to study leaching and revegetation -of test stock- piles, Six small (1600 'tons) stockpiles were constructed at the MINNAMAX Project Site and they range in composition from 0.29 to 043 g % copper, 0.075 to 0.09% nickel, and 0.6 to 1.45% sulfur. Two of the stockpiles were covered with mineral soil, one was covered with topsoil, and three were not treated Revegetation plots were established on the piles which received a soil cover. Leachate samples and flow measurements were collected at the base of the piles. Initial results indicate that metal concentrations in leachate samples range from 10 to 10,000 times the concentrations found in the streams of the area. During the first growing season, the test pile covered with topsoil yielded 30% less water than untreated test piles. No reduction in yield was observed for the piles that were covered with the less fertile mineral soil. First-year vegetative growth, expressed as biomass, was four times greater on the-topsoil pile than on the mineral soil piles. The long-term effects of vegetation on leachate quantity and quality continue to be investigated.

Jan 1, 1980

By Ananta L. Yennamani

Blast movement measurement (BMM) transmitters are a practical method to measure three-dimensional (3D) rock movement because of blasting. The BMM transmitters are activated, programmed and installed in specially designed drill holes prior to the blast and the BMM detector locates the transmitters after the blast. The BMM software then calculates and summarizes the 3D movement of each BMM transmitter ball. This information helps to redefine the ore and waste boundaries and enables improved ore and waste selection, resulting in a genuine step change in grade control. The BMM program was carried out at Newmont Mining Corp.?s Phoenix Mine, in northern Nevada near the town of Battle Mountain. The mine is in a historic mining district that contains gold, silver and copper. The geology of the pit consists of different formations made up of sandstone, siltstone, limestone, chert-pebble conglomerate, shale, skarn and quartzite, to name a few. Some of the rock is extremely hard and a powder factor of up to 0.5 kg/t (1 lb/st) is required to get adequate fragmentation to ensure sufficient throughput through the crusher and the mill. The result of using such a high powder factor translates into considerable blast movement and heave. This movement means that the ore/waste digging polygons estimated by the ore control engineer from sampling the initial blast holes will no longer be located in their original posi-tions. The purpose of this project was to test the measurement method and to see if locating the digging polygons in the broken muck pile and excavating to those polygons will improve grade control through the mill. Case studies (Zhang, 1994), (Taylor, 1995), (Gilbride, 1995), (Harris, 1997), (Taylor, 2003), Barrick Goldstrike (Gold-strike Mine, 2008), Ruby Hill Mine (Hilkewich, 2009), (Porcupine Mine, 2005) and (Aguirre, 2010) have shown that, by accounting for the blast movement, there is a potential to increase mineral recovery by as much as 25 percent for individual blasts for only a modest cost increase.

Jan 1, 2011

By R. W. Wittkopp

The Relief Canyon gold deposit is located approximately twenty- four kilometers east of the town of Lovelock in Northwestern Nevada. At Relief Canyon, the Late Triassic Grass Valley Formation has been thrust over the Late Triassic Natchez Pass Formation. The lower plate Natchez Pass Formation is composed of massive gray dolomitic limestone which is locally silty and sandy. The upper plate Grass Valley Formation is composed of shale, siltstone, argillite and quartzite. Gold mineralization at Relief Canyon occurs along the highly brecciated thrust contact between these two formations. Weak gold mineralization often occurs above the thrust in the Grass Valley Formation, however, most of the ore grade mineralization is present below the thrust in the brecciated Natchez Pass Formation or where the two formations are mixed as a result of movement along the thrust. Several types of gold mineralization have been recognized at Relief Canyon. A large amount of the ore is present as a jasperoid breccia, however, significant amounts of ore occur as a mixed breccia composed of upper plate rock, fresh limestone, clay and jasperoid breccia. Gold ore also occurs in a fresh limestone breccia which contains a large amount of clay. Below masses of jasperoid, jasperoid stringers containing gold extend into the fresh limestone. Gold mineralization at Relief Canyon appears to be truly disseminated and has the typically associated trace elements of arsenic, antimony, mercury and fluorine. The Relief Canyon deposit can be classified as a structurally controlled disseminated gold deposit. Other deposits that fit this classification are the Pinson and Dee gold mines.

Jan 1, 1984

By Serhat Özdemir, Derya Öz Aksoy, Pınar Aytar Çelik, Ahmet Çabuk, Sabiha Koca, Hüseyin Koca

In carbonate flotation, oleate has been used for many years as a collector in industrial scale. Compared to sulfide minerals, the flotation of carbonate minerals requires more collector consumption and has lower yield and selectivity. It has been previously shown that surfactin provides higher yields in smaller amounts than oleate in the bioflotation of calcite as one of the carbonate minerals. In this study, the usability of surfactin as a flotation collector for magnesite was investigated. For this purpose, the adsorption of surfactin on the magnesite surface was inspected with analyses such as FTIR, SEM–EDS, contact angle, and zeta potential measurements. In addition, the effect of surfactin on the surface tension of water was also revealed. The same analyses were also performed for oleate as a reference point. All flotation experiments were performed without optimizing with both collectors. FTIR results showed that the surfactin, like oleate, was chemically adsorbed on the magnesite surface. Surface tension analyses showed that the surface tension of water decreased to approximately 32 N m− 1 at 10− 4 M oleate concentration, and this value decreased to below 25 N m− 1 at the same surfactin concentration. According to contact angle measurement results, the contact angle of magnesite was 85° after the surfactin adsorption of 2 × 10− 4 M concentration, while this value remained at 46° for oleate. Finally, according to flotation experiments, high temperatures and high collector dosages are necessary for acceptable flotation recovery with oleate, yet surfactin can produce the desired result at ambient temperatures and lower collector amounts.

Dec 13, 2022

By D. Scott Scovira, Thomas Gustavsson

Exiting WW2, the potential of nitrates and hydrogen peroxide for application as industrial explosives both became known. The technology stream advanced the development and uptake of nitrate-based explosives to the point that they are the current global standard for blasting. Recently environmental issues are influencing the strategic agenda of extractive industries. The mid-2010s saw renewed interest in hydrogen peroxide explosives to eliminate NOx fume. Carbon reduction initiatives in the 2020s provided additional impetus to investigate hydrogen peroxide-based explosives. Hypex Bio is at the forefront of developing and delivering bulk gas sensitized Hydrogen Peroxide Emulsion (HPE) for blasting. HPE consists of hydrogen peroxide along with smaller amounts of fuel and emulsifier. The consistency of HPE is similar to industry- standard nitrate-based emulsions. It is compatible with existing priming and initiation systems. HPE does not contain nitrates and thereby does not produce post blast nitrous oxide fumes nor discharge of nitrates or ammonia to mine water. Importantly, HPE contributes to reduction in total carbon emissions as compared to nitrate-based explosives.

Feb 1, 2025

By Juan J. Monsalve, AMAN SONI, ALEX PFREUNDSCHUH, Nino Ripepi

Ground control failures are one of the main causes of accidents in the underground stone mining industry. Some of the fundamental tools for rockfall hazard identification are related to rock mass characterization and geotechnical discontinuity mapping. Recent technological advances in these methods are related to remote sensing techniques and pointcloud processing software for automated discontinuity mapping. Remote sensing techniques, such as LiDAR and photogrammetry, generate multimillion-point clouds with millimetric precision, capturing the structure of the rock mass. The automated point-cloud processing tools offer alternative algorithm-based methods to characterize and map these discontinuities. However, their applicability is constrained by multiple factors, such as site-specific conditions of the rock mass and the parameters used within the mapping algorithms. This paper evaluates the performance of automated discontinuity extraction software compared with manual virtual discontinuity mapping. Sampling windows from laser-scanned sections in an underground limestone mine are defined and mapped using the Discontinuity Set Extractor (DSE) opensource software. Results from the virtual discontinuity software are compared with manually extracted fractures from I-Site based on reviewing orientation, trace length, spacing, number of extracted discontinuities, and processing time.

By Y. Zhang, C. Zhou, M. Girman

Wireless technologies are increasingly being implemented in underground mines for various purposes such as communications, tracking, remote control, remote sensing, and environmental monitoring. However, the adoption comes with risks as common wireless systems, such as WiFi, Bluetooth, IWT (Innovative Wireless Technologies) wireless system, often operate in the unlicensed ISM (industrial, scientific, and medical) band. The shared nature of the ISM band can lead to interference among devices and consequently cause performance degradation and reliability issues. In this study, we developed two wireless communication evaluation boards as a tool to evaluate the performance and reliability of a wireless system with the presence of electromagnetic interferences (EMI) from other wireless systems in underground environments. We adjusted various parameters including signal power from adjacent frequency channels, noise power within the same channel, the movement of personnel, and communication packet size. Our findings indicate that, while the power of the EMI source plays a key role, the motion of personnel in the tunnel also has a strong impact on performance, and this impact increases as the power of EMI sources increases. In noisy environments, smaller packet sizes are preferable as they enhance the likelihood of successful transmission. High levels of interference or noise can lead to increased packet loss or error rates, potentially causing communication links to fail completely or become ineffective. The evaluation boards utilized in this study are based on a practical wireless transmission system deployed in a remote controller for a heavy mining machinery used in underground coal mines. The results and findings presented in this paper can aid in the design of wireless systems that are resilient to EMI in underground mining environments.

Feb 1, 2025

By Jörg Holzhäuser, Matthew Crow

An 18.5 km (12 mile) long tunnel is being driven by four Earth Pressure Balance Tunnel Boring Machines (EPB-TBMs) of 4.7 m (15.5 ft.) diameter through alluvial sand, gravel, silt and clay above and below the groundwater table in Los Angeles beneath buildings, railroads, freeways and the L.A. River. Continuous automatic data recording of TBM operation and field inspectors' records, accompanied by monitoring of 5,000 surface reference points and 268 borehole extensometers were used to obtain information. The paper explains the reason for selecting the method of EPB-tunneling to ensure stability of the tunnel and meeting of environmental requirements, and presents data collected to monitor and demonstrate the performance of the TBM sin the different ground conditions encountered.

Jan 1, 2003

By W. D. Hausel

The Wyoming craton in the western United States is a favorable terrane for diamond deposits. The craton hosts a variety of ultramafic, ultrabasic, and ultrapotassic rocks. Additionally, a few hundred 'kimberlitic' heavy mineral anomalies and some geophysical and remote sensing anomalies indicate the presence of undiscovered, mantle-derived, pipes in the craton. The Wyoming craton is separated into a Wyoming 'archon' known as the Wyoming Province, and the Colorado 'proton' known as the Colorado Province. The 'archon' underlies much of Montana and Wyoming and continues north into Alberta and Saskatchewan; the Colorado 'proton' underlies much of Colorado and a small portion of Wyoming. Although most exploration geologists would consider the 'archon' the most favorable terrane for commercial diamond deposits, the 'proton' has produced more than 120,000 diamonds, while the 'archon' has not been very productive.

Jan 1, 1996

By Eric Lutz

"Great effort has been expended for more than 40 years to improve the workplace safety and health of surface and underground miners across the United States. When looking at the past decade, withstanding the 2010, Upper Big Branch (UBB) disaster that took the lives of 29 miners, this effort has resulted in a generally decreasing trend from 57 fatalities (22 coal; 35 metal/non-metal) in 2005, to 45 (16 coal; 29 m/ nm) in 2014. Through August of this year, there have been 23 mining-related deaths (eight coal; 15 m/nm). These results reflect continued diligence and perseverance on the part of miners that stay true to our legacy; and demonstrate significant investments from mine-site leadership, mining corporations, and state and federal regulators. However, over the past five years there have been an average of 32 fatalities per year, with a low of 36 (2011 and 2012) to a high of 45 (2014). If we know that there will be somewhere between 30 and 50 mining related deaths next year, which of us will volunteer to be counted as one of the numbered? Clearly, we all agree that one fatality is too many; and as evidenced by changes following UBB, deaths in any sector are deaths reflective of all mining across all sectors.The impact of each miner death touches us all. Miner’s deaths are felt deeply by family and friends, most significantly the children; their communities in which they served, supported, and worshiped; and by society that has lost a hardworking, dependable contributor. Further, to take a slightly cynical, but realistic view, miner fatality events impact the financial vitality of mining and contracting companies and broadly diminish investor confidence. Just as important, these events significantly impact our communities and result in negative public perceptions, which ultimately drive regulatory policy and related compliance pressures. This resulting pressure forces operations to broadly address safety and health gaps in very specific ways (i.e., see U.S. Mine Safety and Health Administration (MSHA) regulations regarding lids for trash cans) minimizing a mine site’s opportunities for operational flexibility. To break this cycle that is the operational reality, mining companies are focusing tremendous efforts on fatality prevention and specifically on dedicated investment to prevent multiple fatality events."

Jan 1, 2015