Search Documents

Roof falls in coal mines typically occur in or around intersections and this has not changed in the last two decades. This research develops an improved scientific understanding of stress distribution and associated failure behavior around 4-way and 3-way coal mine intersections. Three-dimensional numerical analyses were performed to determine factors that influence intersection stability. The analyses used Hoek-Brown failure criterion. Failure zones around 3-way and 4-way intersections were developed. Intersection span and horizontal stress have a major influence on intersection stability. For the 4-way intersection, pillar corners across the intersection fail first and lead to progressive failure of immediate roof and floor layers. The mechanism of failure is similar for the 3-way entry but the shape and extension of failed zones differ. Coal ribs mostly fail due to tensile stress, while roof and floor strata fail due to shear stresses. Rib corners fail due to a combination of shear and tensile stresses. In addition to stress distribution; safety factor contours analysis was performed to assess stability of intersections.

Feb 27, 2013

A methodology has been developed and demonstrated to be effective in reclaiming surface-mined land for a forestry post-mining land use. The Forestry Reclamation Approach (FRA) has been applied, almost exclusively, to flat or gently rolling surfaces. One of the primary steps in the FRA is to loosely grade the top 1.22-m (4-ft) of soil or substitute root growth medium to avoid excessive compaction. Concern has been expressed by regulators and the public that loose grading on steep slopes could lead to slope failures, which is one of the issues that SMCRA sought to correct. A field investigation was conducted at a steep-slope contour operation in eastern Kentucky to test the applicability of FRA in this setting. Final grading was performed according to FRA standards. The surface consisted of two distinct substitute rooting media. One was unweathered gray sandstone and the other was a combination of gray sandstone, brown sandstone, and topsoil. A variety of native hardwoods was planted following the FRA guidelines. The slope was instrumented with 70 survey monuments to monitor for mass movement. The reclaimed spoil was also characterized using bulk density and penetrometer resistance methods. The characteristics of both spoils are similar to those observed on flat to rolling surfaces where the FRA has been used and, after one year, approximately 70% of the trees had survived. There has been no major mass movement of the slope and slope stability analyses indicate that the application of the FRA has little impact on the overall stability of the slope.

Jan 1, 2011

By Ray Wood, Rene Sterk, Robin Falconer, Sean Aldrich, Simon Nielsen

"The Chatham Rock Phosphorite project is situated 450 km east of New Zealand at approximately 350 to 450 m water depth. The deposit occurs as a thin layer of phosphatebearing glauconitic sand at the surface of the sea floor and has a thicknesses typically ranging from 0 to 1 m. The sand layer consists of mainly silt and sand-sized sediments, with phosphatised chalk nodules up to 15 cm in diameter. Phosphate nodules were first discovered on the Chatham Rise in the 1950s by a New Zealand Government survey. During the 1960s to 1980s several private and government sponsored cruises explored the Chatham Rise and surrounding seafloor area. A total of 1174 samples were collected over a 600 km2 area with the majority of the samples collected using a pneumatic -or large Van Veen-style grab-sampler.Since acquiring the licence in 2010, Chatham Rock Phosphate Limited has conducted six cruises in two programs in the Project area. A total of 261 samples were collected using a Van Veen grab, box core and grab samples.Sample quality and QA/QC measures varied considerably between the cruises and within each cruise. A critical part of the assessment of the data collected in the Project area was to determine what quality thresholds to use to allow or disallow data to enter into the estimation process. As part of the data verification process, the relative and absolute quality of the data was assessed in as much detail as practically possible. The best samples were those that were collected using the pneumatic grab, sampled the full sand horizon, had a small location survey error and had no other apparent data ambiguities. This paper describes the challenges for mineral resource estimation for an unconventional style of mineralisation using unconventional sampling techniques."

Sep 1, 2014

By Richard Kastner, Emilie Vanoudheusden, Fabrice Emeriault, Jacques Robert

INTRODUCTION The subway line B of Toulouse (France) has been realized with three different tunnel boring machines (TBM) techniques: Contracts 2 and 5 are excavated with earth-pressure balanced TBM, Contract 4 with a slurry shield TBM, and Contract 3 with a compressed-air TBM. The first three machines are around 7.7 m in diameter, while the last one is 5.3 m. Moreover, a small part of the line (50 m) has been excavated by a conventional method. The tunnels run through the Toulouse molasses, composed of hard sandy clay with pockets and lenses of dense sand. Geotechnical investigations have shown that in these formations, K0 is greater than 1, around 1.8 at a depth of 25 m (Serratrice,2005) and that geotechnical characteristics are homogenous on the whole layout (? =22 kN/m3, Su = 300 kPa, c' = 30 kPa, F' = 32°). The water table is found between 2 and4 m below ground level. As geology, stratigraphy and tunnel cover (between 10 and 20 m) are almost identical, a comparison of movements induced by the excavation by each of the four excavation techniques is possible. This paper presents the soil mass movement measures in the case of the conventional excavation method and in the case of TBM sections. It shows how tunneling parameters may explain the different surface movements observed during excavation. For the sake of simplicity, only the results of Contract 2 (earth pressure balanced TBM)will be presented. MONITORING Monitoring for the Conventional Method Section For the conventional method section (Vanoudheusden et al. 2005) the mass soil movements are measured with two inclinometers and one multi-point extensometer borehole with automatic data acquisition (Figure 1). The monitoring devices include

Jan 1, 2007

By S. C. Brown

A number of studies have suggested that microscale asperities enhance bubble-particle attachment efficiency; however, in practice the roughening of particulate surfaces can also lead to a decrease in flotation. In the present investigation, it is proposed that nanoscale asperities may be partially responsible for this phenomenon. It is suggested that as inter-asperity separation distances are reduced capillary effects are enhanced leading to the formation of stable liquid domains, which adversely impact bubble-particle adhesion. In addition, obstruction of surfactant self-assembly may occur, further limiting flotation.

Jan 1, 2003

By C. Bazin

The separation of rare earth elements is a complex process that is industrially carried out using liquid/liquid extraction. Detailed flow sheets of solvent extraction plants for the separation of rare earth elements are rarely available in the literature which limits the opportunity to teach and test the application of data reconciliation, process optimization and control to these types of plants. The basis of a simulator for a rare earth elements separation plant is described in this paper. The simulator is used to adjust the organic phase and stripping acid flow rate in a separation circuit of heavy rare earth elements from light one?s.

Feb 27, 2013

By Jacques Nantel

Mechanization has been at the core of productivity improvements since the industrial revolution. During the past 20 years, mining has derived spectacular progress from mechanization. In the future, however, mechanization alone will not be enough. In the next few decades, automation will bring about new generations of highly productive and safe machines, with low operating costs. Increased use of new and better technology is generally accepted as the prime factor capable of closing the productivity gap. The productivity gap is the difference between inflation and metal prices. The three S-curves in Fig. I represent the evolution of technology in general, and mining in particular. TI represents incremental changes. the dominant sort of technology changes in the mining industry: - Better drills, electric hydraulic drills vs. pneumatic drills, the drilling rate is twice as fast. - Better steel and bits, to accommodate the higher performance drills. - Improved chemical explosives. - Bigger trucks in open pits.

Jan 1, 1993

Editor?s note: Each year, the June issue of Mining Engineering features an industrial minerals review. Several people put in a fair amount of time in developing the material for this issue. Thank you to the industrial minerals annual review editor, to the technical committees chair and vice-chair, and to the authors of the individual commodity profiles. Jim Norman, member SME, of GeoTrans, Inc., is the industrial minerals annual review editor. SA Ravishankar, member SME, of Cytec Industries, is chair of the industrial minerals technical committees. Technical committee vice chairs include: ? Abani Samal, member SME, of Pincock Allen & Holt, agricultural minerals. ? Aaron McMahon member SME, of Pincock, Allen & Holt, ceramics and refractories. ? Bradley S. Van Gosen, member SME, of the U.S. Geological Survey, chemical raw materials. ? Mark Zdunczyk, member SME, of Continental Placer, Inc., construction materials. ? Jerry Gauntt, member SME, of JEG Minerals Consultants, fillers and pigments. ? Michael Cheshire, member SME, of Indiana University, sorbents, filters and process aids. Their help makes possible this June industrial minerals issue. On behalf of ME readers, the editors thank them.

Jan 1, 2008

By Nural Kuyucak

Several thousand years ago, metallurgists discovered that by combining two relatively soft metals, copper and tin, they could make a new material, bronze, that was stronger than either metal separately. Bronze and other alloys show how different materials can be integrated to create something new and better. Today?s mining industry can likewise find benefit in an integrated approach to managing the external impacts it has through its waste materials and its use of water. Just as using bronze gave ancient nations an economic and military advantage, mining companies can gain competitive advantage through finding better ways to manage water and waste. Trends pushing this include: ? Environmental ? Regulations on water-taking and the quality of discharged water are becoming more stringent. Net zero discharge requirements are often imposed by regulators. Mining companies also come under pressure to manage environmental impacts of mine waste, including minimizing the area occupied by waste and seepage amount resulting from infiltration of water from a smaller surface area. ? Social ? Particularly in arid parts of the world, there are multiple possible uses for each gallon of water. Local residents do not want to see a reduction in supplies of water for agricultural, domestic, manufacturing and other purposes. They get suspicious about any potential impact of water being mixed with their water reservoirs if it comes from a mining site, even if it would be treated. Such suspicions may cause conflicts among the stake-holders and delays in project approval processes.

Jan 1, 2009

The National Institute for Occupational Safety and Health (NIOSH) conducted a monitoring field study to optimize the rib control plan in a room-and-pillar coal mine. The study mine is located in the Central Appalachia coal basin. Two monitoring sites were selected at different sections in the study mine. The selected sites have different overburden depths and geologies. The instrumentation plans at study sites include borehole pressure cells installed at various depths in studied pillars, rib and roof extensometers and load cells mounted on number of the rib bolts. The instrumentation results and observed geology for one of the study sites showed great potential for optimizing the rib bolt plan at that section of the mine. Therefore, a rib support optimization study was followed using numerical modeling technique. A calibrated threedimensional model was developed using the instrumentation results of the optimization section. The calibrated model was used to determine the optimum rib support for expected overburden depths and rib heights. Baseline rib bolt patterns were assumed for the optimization study. Additional rib bolts, above and beyond the baseline bolting parameters, were outlined and identified as solutions to contain the rib fracturing identified by the modeling results.

Jul 28, 2020

By J. Donovan Jacobs

Many improvements in the art of underground excavation have appeared during the past two decades. These improvements have been both in methods and in machinery and have resulted in more economical construction of today's tunnels. In the realm of machines, the developments of continuous boring heads for either soft ground or rock, random arm excavators and the sliding tunnel floor (Magic Carpet) have each made contributions toward more rapid tunneling. CONTINUITY OF ADVANCE Tunnel boring machines are often referred to as "continuous excavators". Continuous advance (without cyclical interruptions) has not been achieved, however, in any of the machines now in use. In most rotary-head tunnelers the thrust needed to make the cutters bite into the face is obtained from hydraulic cylinders reacting against anchoring devices held stationary by pads which grip against the sides of the tunnel. With this system the forward motion of the cutting head is continuous only until the propelling cylinders have reached their limit of extension. At this point the grippers must be released, moved forward and reset before a new cycle of advance can be begun. Some machines are built to obtain their propelling thrust from hydraulic cylinders pushing backward against newly-installed rings of tunnel support. This is the customary method for propulsion of shields. With it, each cyclical advance or "shove" must await the erection of a new ring of supports. Faster tunnel driving

Jan 1, 1974

By A. M. Elmahdy

An amphoteric collector was tested for dolomite removal from phosphate ore. The effects of some operating parameters and their significance on the flotation of dolomite were studied using statistically designed experiments. The parameters studied were impeller speed, pH and collector dosage. Analysis of the results showed that pH is the most significant parameter. Moreover, a concentrate containing 0.53% MgO and ~31.1% P2O5 with a recovery of ~ 90% can be achieved at optimum values of studied parameters, i.e., a pH of 12, an impeller speed of 1,000 rpm and a collector dosage of 2.5 kg/t.

Jan 1, 2007

By Larissa Koroznikova, Steve Durkin, Patrick Bouwmeester, Michael Tuck

In currently used mining methods, blasting techniques often causes dilution of valuable ore and results in costly processing requirements. In the context of narrow vein mining of thin and highly concentrated orebodies there is a need of a mining method that can reduce dilution in order to remain economically viable. This research project explored the viability of a new mining technology, thermal fragmentation, in narrow vein mining. Thermal fragmentation technology uses a flame jet to produce extreme heat that spalls the surrounding rock to a strategically located drill hole, as an alternative to traditional blasting. This paper creates a net present value (NPV) model of a mining method using thermal fragmentation, as well as for an existing method used for narrow vein mining; comparisons and evaluations were made regarding the feasibility of the new technology. It was found that while overall costs for thermal fragmentation were relatively high, reductions in wages, haulage and processing costs, as well as increased productivity and ore recovery, meant that the new method would improve the financial performance of any operation. These results identify that there is an opportunity to introduce the thermal fragmentation technology to narrow vein mines within Australia, in order to lower costs and increase profit.

By Vincent Tirolo

The proposed Second Avenue Subway is a new two-track subway line running from 125th Street and Park Avenue at the north, east along 125th Street to Second Avenue and south along Second Avenue to the Financial District in lower Manhattan, NY with 16 new stations and 13.6 km (8.5 miles) of track. The project has been broken into four construction phases. The initial Phase 1 operating segment includes three new stations (96th, 86th and 72nd Street stations) with a connection to the existing Broadway line at the 63rd Street Station at Lexington Avenue. Rehabilitation of the 63rd Street Station is also included in the scope of Phase 1. Subsequent phases extend service north and west to 125th Street (Phase 2), south to Houston Street (Phase 3) and finally to Hanover Square (Phase 4). The DMJM Harris/Arup Joint Venture (DHAJV) prepared the Contract Documents MTA for Phase 1. Parsons Brinckerhoff is providing the MTA with construction inspection services for Contract C-26002. In April 2007, NYCT awarded first Phase 1 for $337 million to S3 Tunnel Constructors, a tri-venture comprised of Skanska USA Civil, Schiavone and Shea. Contract C26002 is for the construction of the tunnel boring ma-chine (TBM) launch box and the mining of the TBM tunnels from 92nd Street to 63rd Street. The major part of the contract is to construct a shaft, commonly referred to as the launch box, from East 92nd Street to East 95th Street having dimensions of 244-m- (800-ft-) long by 18.9-m- (62-ft-) wide and a depth of 19.8 m (65 ft), including more than 91,000 m3 (119,000 cu yd) of soil and rock contained within its walls. The launch box will ultimately become the southern half of the 96th Street Station. The focus here is geological conditions at the launch box and existing structures along the launch box. These geologic conditions and existing structures had a major influence on the selection and design of the support of excavation system (SOE), the SOE bracing system, construction staging, the ground movements, dewatering and other challenges of constructing the launch box (Fig. 1).

Jan 1, 2013

By Dennis Molvik, Omar Fulton, Chris D. Breeds, Don Gonzales

This paper presents and describes the South Interceptor Parallel Phase III Contract C93012C, which involved construction of a nominal 2.7 m (9-ft) finished diameter sewer conveyance using both pipe jacking and conventional tunneling methods. Earth Pressure Balance (EPB) excavation was required to minimize the potential for settlement beneath a main rail line, overpass, sensitive wetland, areas of contaminated soils, and nearby structures. Ground conditions predicted in the Geotechnical Baseline Report included low plasticity, clayey silt (40 to 10%) and silty sand (60–90%) with pieces of wood such as logs, stumps, branches and other tree fragments. Soil cover ranged from 2.7 m (9-ft) to 5.4 m (18-ft) over the tunnel crown with a groundwater table between 1.5 m (5-ft) and 3.7 m (12-ft) deep.

Jan 1, 2003

By D. R. Dolinar

The fall of small pieces of rock between roof bolts causes over 80 pct of the ground fall injuries in underground coal mines. Roof screen, if installed on the bolting cycle, can significantly reduce the number of these injuries. As the surface of the roof fails, the screen will have to retain the broken rock without failing or excessive deformation. Welded wire screen is the most common type of screen material used for roof surface control in underground coal mines. The load-deformation characteristics and the load capacity of welded wire screen were evaluated in the laboratory in a specially built test frame. In the frame, the square screen sections were held in place by bolts and bearing plates at the four corners while a center load was applied to the screen. The parameters evaluated included the wire gauge and configuration, the bearing plate loads and bolt spacing. The wire gauge of the tested screen was 4, 6, 8, 9 and 10. Maximum screen capacities for both load and displacement were developed for each of the wire gauge sizes along with the screen stiffness. This information can be used for screen selection and for the evaluation and determination of screen performance. DISCLAIMER: The findings and conclusions in this report have not been formally disseminated by the National Institute for Occupational Safety and Health and should not be construed to represent any agency determination or policy.

Jan 1, 2009

By F. D. Fox

The Flambeau and Ridgeway Mines, both owned and operated by wholly owned subsidiaries of Kennecott Minerals Company, were located very close to populated areas having initial concerns about health, safety and the environment. The success of both operations depended upon developing a framework of community support and enhancing sustainable development opportunities throughout the entire life cycle of the mining operations to address these concerns. The protection of the Flambeau River was the cornerstone of the Flambeau Mine’s success. The highest priority for the Ridgeway Mine was to ensure long-term physical, chemical and ecological stability of the reclaimed mine site. Both of these goals have been achieved and are discussed in this paper, which highlights Kennecott Minerals Company’s integration of sustainable development principles into its business decision-making and management processes.

Jan 1, 2003

By Jia-Shyan Shiau, Chung-Ken Ho

An uneven gas distribution through the burden layers inside a blast furnace (BF) results in abnormal gas resistance or pressure changes. Rapid variations in the abnormal gas resistance will lead to the occurrence of channeling. A visualization technology mainly made of pressure distribution was developed to predict BF channeling phenomena in this study. The real-time data of BF shaft pressure was used to create a 3D visual model by neural network algorithms and 3D real-time BF pressure changes were observed. The root mean square deviation (RMSD) of the BF shaft pressure was used as an index to set up the predicting criteria of channeling occurrence with the opening of BF Annular Gap Element (AGE), and a predicting system based on the criteria was built. The two criteria for the channeling alarm are the RMSD of the BF shaft pressure (> 0.15 kg/cm2 ) at the upper two levels, and the AGE opening being greater than 60%. This system has been installed in the China Steel Corporation (CSC) BFs, and the test results showed that a prediction can be obtained 8 to 16 min ahead of channeling allowing sufficient time for the operator to adjust the BF operation in order to avoid the occurrence of channeling.

By Shanming He, Jinliang Wang, Xiaoming Wang, Chunfa Liao

Large amounts of manganese-rich slag were generated from smelting low-grade manganese ore containing high iron and high phosphorus in electric furnace or blast furnace, which contain 25–40 mass% Mn. This paper describes an efficient hydrometallurgical process for the utilization of high manganese slag instead of conventional usage of pyrometallurgical route for manganese recovery. Pressure acid leaching of manganese-rich slag using air as pressurized gas is studied systematically. The effects of mass ratio of manganese-rich slag to pyrite, concentration of sulfuric acid, leaching temperature, partial air pressure, leaching time, and liquid-solid (L/S) ratio on the separation of manganese with other main impurity components were investigated comprehensively. Under the following optimal process conditions, weight of manganese-rich slag powder,100 g; mass ratio of manganese-rich slag to pyrite, 20:1; sulfuric acid concentration of 140 g/L; air pressure of 0.6 MPa; leaching temperature of 140 °C; leaching time of 1 h; L/S of 7:1; ore size of 75–80 μm; and stirring rate of 600 rpm, the extraction rate of Mn reached 94%, and the dissolution percentage of Si, Al, and Fe are as low as 2%, 6%, and 10%, respectively. The leaching slurry presented a good solid-liquid separation characteristic. The silicic acid formed during sulfuric acid leaching manganese silicates was converted to filterable dehydrated SiO2 particles which precipitated in the residue under the condition of higher temperature with higher pressure. The effect of adding pyrite may be to reduced iron ions and decreased the output of iron hydroxide colloid and also reduced MnO2 to manganese sulfate in sulfuric acid leaching. Thus the formation possibility of colloid such as silica gel and iron hydroxide was decreased, and higher yield of manganese sulfate could be achieved.

By Shanming He, Jinliang Wang, Xiaoming Wang, Chunfa Liao

Large amounts of manganese-rich slag were generated from smelting low-grade manganese ore containing high iron and high phosphorus in electric furnace or blast furnace, which contain 25–40 mass% Mn. This paper describes an efficient hydrometallurgical process for the utilization of high manganese slag instead of conventional usage of pyrometallurgical route for manganese recovery. Pressure acid leaching of manganese-rich slag using air as pressurized gas is studied systematically. The effects of mass ratio of manganese-rich slag to pyrite, concentration of sulfuric acid, leaching temperature, partial air pressure, leaching time, and liquid-solid (L/S) ratio on the separation of manganese with other main impurity components were investigated comprehensively. Under the following optimal process conditions, weight of manganese-rich slag powder,100 g; mass ratio of manganese-rich slag to pyrite, 20:1; sulfuric acid concentration of 140 g/L; air pressure of 0.6 MPa; leaching temperature of 140 °C; leaching time of 1 h; L/S of 7:1; ore size of 75–80 μm; and stirring rate of 600 rpm, the extraction rate of Mn reached 94%, and the dissolution percentage of Si, Al, and Fe are as low as 2%, 6%, and 10%, respectively. The leaching slurry presented a good solid-liquid separation characteristic. The silicic acid formed during sulfuric acid leaching manganese silicates was converted to filterable dehydrated SiO2 particles which precipitated in the residue under the condition of higher temperature with higher pressure. The effect of adding pyrite may be to reduced iron ions and decreased the output of iron hydroxide colloid and also reduced MnO2 to manganese sulfate in sulfuric acid leaching. Thus the formation possibility of colloid such as silica gel and iron hydroxide was decreased, and higher yield of manganese sulfate could be achieved.