Search Documents

It is a great honour to officiate at the celebration of the centenary of the South African Institute of Mining and Metalurgy. Tonight's festivities bring back happy memories of my association with South Africa's mining industry during my tenure of office as Minister of Mineral and Energy Affairs. They also remind me of the illustrious personalities who have preceded me on this podium. The Pioneers They include Sir Percy Fitzpatrick, who spoke in 1909 on the eve of the Union, General Smuts, and, on many occasions during the 1920s and 1930, Jan H. Hofmeyr. The basic issues addressed by them continue to enjoy the Institute's attention today, namely the optimal and safe exploitation of our country's mineral resources and cost-effective extraction of minerals from their ores. Translated into the Institute's key objective it reads: To initiate and give effect to the means whereby the requirements for technology and scientific knowledge if the minerals and metals section if the South African economy is satisfied.

Jan 1, 1994

By Timo Niitti, Antti Rinne, Janne Turunen, Klaus Schommarz, Sami Grönstrand

This paper captures the essential steps employed in developing Outotec?s new FloatForceTM mechanism. The development of a flotation mechanism essentially revolves around the efficient transfer of installed power, or capital cost, to optimum flotation performance. Optimum flotation performance will be achieved if a balance between metallurgical results, operating and capital costs is maintained. The development of the FloatForceTM mechanism was done by careful evaluation of each of these three areas. This paper focuses on how experience, CFD and laboratory equipment, pilot and plant tests are used to test and evaluate a new flotation mechanism. Validated variables include mixing profile, power draw and local air hold-up. Metallurgical and mechanical design considerations are not covered in this paper. Besides using the FloatForceTM mechanism in new flotation equipment, the FloatForceTM mechanism can be used in existing flotation cell installations, thus enabling improvements in the mixing profiles, solids suspension and metallurgical performance of operating flotation circuits. Results of several tests carried out in existing plant operations are presented.

Jan 1, 2007

In many practical situations, calculation of the point semivariogram is not necessary. Such a case is analysed in this chapter. The purpose of this analysis is to give a better understanding of the meaning of the mathematical formulae developed in the previous chapters. A similar problem will be studied in Chapter 11, using the point semivariogram.

Jan 1, 1978

By J. J. Taute, N. B. du Preez

"A well-performing solvent-extraction circuit is a key part of producing good quality copper cathode. To ensure consistent operation, a good understanding of the circuit’s operation and an ability to rapidly troubleshoot key parameters is required. This paper briefly discusses the modeling of solventextraction circuits. The paper then goes on to discuss the determination of key performance parameters from plant data and comparing these with the circuit models to quantify circuit performance. The identification and troubleshooting of circuit issues is presented with a worked example. INTRODUCTIONA well-performing solvent-extraction (SX) circuit is a key part of producing good quality copper cathode. To ensure a consistent, high-quality operation, a good understanding of the circuit performance is required. Evaluating the performance of an SX circuit is an extensive topic. The objective of this paper is to focus on the evaluation that the metallurgist should be performing on a regular basis using flow and concentration data. This paper does not cover important topics, such as crud management, phase continuity, or organic management. Some basic SX modeling concepts are first be presented. The calculation of the parameters is then presented with a brief discussion and recommended ranges (where applicable). A worked example is used to provide a basis for further discussion on the evaluation of the calculated parameters and use of data collected.BASIC SOLVENT-EXTRACTION MODELING CONCEPTSThis section presents the basic modeling concepts used in SX simulation packages currently available. SX reagent suppliers have invested significant time and effort into collecting data on the performance of their reagents under different conditions. Based on these data, suppliers have developed packages which they normally make available to their clients for free. These are typically used for process design and plant optimization studies. For example, BASF developed ISOCALCTM and CYTEC Industries developed MINCHEM® and MEUMTM.Chemistry of Copper Solvent ExtractionLiquid–liquid extraction involves the selective transfer of a substance between two immiscible liquid phases by controlling the relative solubility in each phase. In the case of copper SX, the exchange is typically achieved by an oxime-based chelating mechanism. In particular, mixtures of aldoxime and ketoxime are normally used in conjunction with modifiers. More detail on this extensive topic can be found in Schlesinger et al. (2011)."

Jan 1, 2015

By M. Kilfoil

Many minerals processing operations result in crushed rock being mixed with a liquid. Sometimes, the rock particles have to be dried before the next process begins and there may be a considerable distance between the equipment carrying out these processes. Bateman Engineered Technologies (BET) developed, patented and commercialized a method of simultaneous pneumatic conveying and drying. A joint project to assist with optimizing the process is under-way. Part of it is a numerical simulation of the process. The simulation is done using a dedicated program written in MATLAB, (commercial software which is widely used in engineering). It accounts for heat and mass transfer as well as particle transport. The main part of the program consists of a loop containing a series of equations which are evaluated sequentially. During any particular iteration, the properties are changed one at a time. Since the properties are changing relatively slowly, this method gives good results. The outputs of the simulation are consistent with the operational experience of BET’s engineers. The output is very comprehensive and all numerical. Since the program is currently being used for research purposes, flexibility is very important. Thus the output is converted into a spreadsheet file. Variations in the output quantities are displayed graphically using MS Excel. Some simulation could have been done using computational fluid dynamics (CFD) software. The advantages and disadvantages (technical, financial and skills requirements) of the two approaches for this particular type of simulation are compared briefly. Keywords: Pneumatic conveying, Heat and mass transfer, Computer model

Jan 1, 2003

By J. A. C. Diering

All underground openings are three-dimensional, and in many cases it is not valid to analyse two-dimensional sections. This has been a problem in the past owing to the magnitude and complexity of three-dimensional stress analysis. In this paper a three-dimensional boundary element approach, using non-conforming quadratic elements, which is specifically applicable to underground excavations, is described. In addition, the philosophy of application of stress analyses is discussed. Three case histories are presented to demonstrate the practical nature of the approach as a tool in solving mining problems.

Jan 1, 1987

By J. Martinovic

The large proportion of gangue minerals present in platinum bearing ores in South Africa provides challenges to the flotation and down stream processes. In order to take effective measures to reduce their recovery in flotation an understanding of the mechanisms and factors influencing their behaviour is needed. Typical gangue minerals are pyroxene, feldspar, quartz, chromite and talc. Of these, talc is a naturally hydrophobic mineral and although it is present in relatively small quantities, it has a disproportionate effect as it has a strong froth stabilizing effect, increasing the recovery of other gangue minerals by entrainment. Talc recovery is effectively reduced with the addition of polymeric depressants. Although the other gangue minerals are assumed to be hydrophilic and their recovery by entrainment is expected to follow the water recovery, there is some evidence that they may be activated by the typical reagent suites used. Reagents such as copper sulphate, added as an activator, and collectors are used to selectively induce hydrophobicity on the sulphides. It has been shown that some of these gangue minerals can be activated. This research work investigates whether inadvertent copper activation is mineral specific and evaluates the mechanisms and factors affecting the reversal of activation with the addition of the depressants using electrokinetic measurements, adsorption and microflotation tests. Results are presented that show that the selected minerals do respond differently and that the reversal of activation is dependent on mineral type, depressant type, dosage and ionic strength of the electrolyte.

Jan 1, 2004

By N. R. Shoko, J. Chirasha

Refractory design remains the most fundamental factor in furnace construction. Refractory design details and proven technology consideration is of paramount importance to come up with an optimum furnace life and to maintain productivity in the life span of the furnace lining. The failure to produce a technically or operationally durable refractory design lining could give rise to pre-mature deterioration of the refractory lining and furnace shell. The premature failure of the furnace lining will lead to extensive heat losses, furnace bath shift, change in taphole orientation and alteration of the Pitch Circle Diameter. A combination of these were experienced at Zimbabwe Alloys? new high carbon ferrochrome furnace. The Zimbabwe Alloys experience has shown an excellent furnace performance in the first two years of operation although signs of an anomaly showed within the first six months of the new furnace. Production slowed down due to induced problems from refractory failure causing furnace distortions impacting on the availability of the furnace and smelting capacity. This paper presents the lessons learnt, measures taken to deal with the premature failure and constraints within which the situation was managed.

Jan 1, 2007

By S. L. Miller

The development of a pilot gold geostatistical ore reserve system proved that geostatistical methods worked well for the routine production of annual ore reserves on gold mines of the Gold Fields of South Africa (GFSA) group, and that the techniques could also be practically implemented, understood and accepted by Survey Department personnel. Many side benefits of the pilot system became apparent, and a variety of useful management information was provided by manipulating the data values that were already captured. It was decided that it was a priority computing project to develop a standard production system (GORS) for routine use by all the GFSA gold mines. Experience with the pilot system enabled detailed functional specifications for GORS to be laid down. These, together with group computing policy determined the terms of reference and constraints for the GORS development. System design could not be finalized until new and appropriate mainframe database software and graphics workstation equipment and software had been found. With these in place the basic system was structured to take best ad- vantage of the interactive features of the workstation, the number-crunching power of the mainframe and the flexibility offered by a relational database and associated 4GL tools. Application sub-systems were developed for data capture, statistical applications, geostatistical calculations, contour plotting and graphical queries. GORS is being introduced to the mines in a phased manner with suitable documentation, training and support structures to enable it to be routinely and effectively used on a day-to-day basis by all group gold mines.

Jan 1, 1987

By M. David

This paper addresses the problem of technological transfer in geostatistics. Expert systems have become popular in certain fields because the needs of the industry are not provided for by traditional concepts and systems of education. The explicit knowledge approach in developing expert systems is presented through two experiments. The first describes a dedicated system written in GOLDEN LISP and the second a shell, using INSIGHT2, which has more general applications. Using expert systems forces on the user a new approach to parameter definition, and as an example an original method for the research of any anisotropy axes is developed which might well be useful in traditional programming. Two examples of application to a coal and a gold deposit are given.

Jan 1, 1987

By J. D. Flint

The geological conditions in the Vierfontein area ~re such that conventional pillar extraction ~stooping) cannot be practised safely or efficiently. Both the open-end lift and the pocket-and-fender methods of pillar extraction have been tried with little success because of problems with roof control and ground stability. The main reasons for the difficulties are the coarse-grained sandstone roof, local weaknesses in the coal seam, and the rate at which the pillars were extracted. The mine has practised bord-and-pillar mining since it started production in 1952, and considerable reserves of coal are contained in the pillars. As an alternative to total pillar extraction, in which hand-loading methods were practised, a system of partial pillar extraction using mechanized-mining methods ~11"modified goaf-line support has been evolved. These remnant coal pillars (snooks) remaining after partial extraction ofthe pillar, together with the installation of 1,2 m" matpacks and a double line of fullcolumn resin roofbolts, ensure control of the edge of the area that has been mined out (goaf). Where roof conditions preclude the use of conventional pillar-extraction methods, this method holds promise as a safe and efficient alternative for the recovery of coal from pillars and for an increase in the volumetric extraction of the reserves within a mining panel.

Jan 1, 1984

By J. A. L. Napier

An analytical solution to the best choice of cutoff grade for a mine is deduced for an assumed model of selective mining. It is found that this choice is determined by the constancy of a special function, the Hamiltonian, over the life of the mine. It is suggested that the appropriate constant value for this function should be determined by the expected long-term average of the paylimit. In that case, the optimum profile can be calculated at each point in time according to the prevailing working cost and product price. In particular, a decision can be made between operation at the true paylimit or at the subsidized paylimit implied by either the lease and tax formulas or the assistance formula for gold mines. It is also shown how the basic formulation can be extended for 'use in the determination of the optimum joint paylimit for two products over the life of the mine.

Jan 1, 1983

By J van Rooyen, S. Archer, M. Fox

The use of dilute sulphur dioxide (SO2) gas mixtures for the oxidation/precipitation of manganese has been explored widely in recent years. The technical merit of the concept is well proven and implementation of the technology on commercial scale is imminent. This paper reviews the technology of manganese removal by means of dilute SO2 gas mixtures and highlights some of the challenges associated with its implementation on industrial scale. A brief review of the technology is presented; the review considers both the mechanism and chemistry of manganese oxidation/precipitation with dilute SO2 gas mixtures. The impact of variables such as temperature, pH and SO2 concentrations on the manganese removal process is assessed. Challenges associated with implementation of the technology on industrial scale are discussed. Gas dispersion is highlighted as a critical design consideration.

Jan 1, 2007

By J. Trcková

This paper describes the method of modelling rock mechanical problems on experimental models. Based on an actual experiment used as an example, assessment of the surface deformation due to undermining, the extensive possibilities of using a 3-D physical model and application results in practice are demonstrated. A special method of modelling the underground mine progress by using paraffin melting is presented. Keywords: undermining, subsidence of surface, 3-D experimental model

Jan 1, 2009

1. USSR co-operation International Mining, the London-based publication, has received USSR Government approval to publish a Russian language edition for circulation in the Soviet Union. 2. Mintek publications Special Publication no. 11. World chromite resources and ferochromium production, by M.H. Silk. 1988. 160 pp. South Africa RlOO including postage; elsewhere US$lOO including postage. Application Report 4 The development and implementation of novel refining processes for the platinum-group metals (including the refining of anode slimes). 1988. 16 pp. Report M249D The acid activation of local clays including solid-liquid separation, by P.M. Cole and G.F. Lahoud. First issued Mar. 1986, reissued Apr. 1988. 46 pp. ReportM250D The production of refined feromanganese in a transfered- arc plasma furnace, by A.F .S. Schoukens and M.Ford. First issued Mar. 1986; reissued Apr. 1988.23 pp. ReportM257D Extraction of gold from eastern Transvaal concentrates by roasting and cyanidation, by J.J. Robinson. First issued Apr. 1986; reissued Apr. 1988. 55 pp. ReportM267D The recovery of gold from backfil by gravity separation, by R.N. Guest. First issued Jun. 1986; reissued Apr. 1988. 18 pp. ReportM285D Autogenous miling of kimberlite, by D.I. Hoyer. First issued act. 1986; reissued Apr. 1988. 11 pp

Jan 1, 1988

By B. Hayen

The principal advantages of fibre optics as compared to copper wire are well known and include almost perfect electromagnetic isolation, light weight, small size, excellent transmission security and substantially better bandwidth/distance performance. The decreasing cost of the optical fibre technology (both fibre cable and equipment) has led to another generation of private networks, which provide much larger bandwidths, very high reliability and an increase of the maximum geographical coverage. The larger bandwidth allows to transport all types of information on a single network. Typical communication requirements are speech (audio), computer data, LAN info, control information, video, etc. OTN or ‘Open Transport Network’ is a transmission system based on the latest available technology in fibre optics. It is characterized by the dual ring approach, resulting in high network availability, and the integration of different types of services in one network. As such, it can fulfil almost all transmission requirements for voice, data, LAN, video and any special service required.

Sep 1, 2001

By G. C. Howell, H. A. D. Kirsten

The mining-induced effects around narrow tabular stopes have traditionally been evaluated in terms of elastic continuum analyses. An understanding of the phenomenological behaviour of the rock surrounding deep-level gold mines has accordingly been developed on the basis of such analyses. However, elastic analyses do not afford reliable representations of the behaviour of rock in which failure may occur on discontinuities. This paper describes investigations that show how the stress and stiffness characteristics of a rockmass are affected under such circumstances for representative ranges of values for the relevant parameters (depth, span, support stiffness, field stress ratio, and discontinuity strength). These investigations afford a substantially different understanding of the mechanical behaviour of rock that is subject to failure. Instead of forming an arch across the abutments, the rock in the hangingwall bears directly across the stope onto the footwall and, instead of being subjected to tension, the nether hangingwall is clamped in compression in the horizontal direction.

Jan 1, 1993

By P. A. Corbeil, C. Swart, F. Miller, V. Falmagne

Automation technologies are increasingly adopted in different mines worldwide. This paper presents the technical aspects of vehicle automation applications at two Noranda operating mines. Teleoperation of 5 LHD’s at Noranda’s Bell Allard mine is used in order to meet aggressive mining requirements under difficult conditions. The equipment is performing under high demand for reliability and performance. In order to further increase performance, automated loading has been commissioned on one of the LHD’s and is being tested. Results to date indicate improved performance with respect to an operator through better filling of the bucket, fewer passes at the muck pile and shorter cycles. Noranda’s Brunswick mine is currently commissioning an automated haulage zone where two optically guided trucks transport ore from a remotely operated chute to two ore passes. Expected operational advantages include increased system capacity and enhanced safety and comfort for the operator. Monitoring to date indicates that the trucks can operate reliably under the conditions imposed by mine production.

Sep 1, 2001

Solvent loading: It is agreed that it is advantageous, as far as reagent cost is concerned, to operate at maximum solvent loading. However, owing to the fact that no reliable automatic solvent flow controller is yet available, control tends to be erratic with the result that there is risk of losing uranium. As can be seen from Mr Tunley's plot, the graph representing total ammonia cost is fairly flat between loadings of 3.5 and 4.0 gpl, while the graph representing uranium loss in the raffinate is steep. It is, therefore, safer to operate slightly below optimum loading in the absence of absolute control. Should the purity of the final product gain importance, operation at optimum loading or even slightly above, may be advantageous. Solvent losses and clarification of pregnant solution: The cost of replacing solvent, as indicated by Mr Carman, represents a high percentage of the overall Purlex costs. It is, therefore, agreed that, amongst other factors, efficient clarification of the pregnant solution and mixer-settler design have an important bearing on the cost. However, as at Blyvooruitzicht, the Buffelsfontein plant can tolerate a suspended solids content of 50 ppm without serious deterioration in efficiency. An increase in the suspended solids content from 15 to 50 ppm normally accounts for an increase of approximately 1 ppm in amine loss. Clarification of acidic pregnant solutions is much more difficult than that of alkaline solutions. Sand clarifiers are being used at Buffelsfontein with moderate success. Clarified solutions containing less than 20 ppm of solids in suspension can be produced, depending on the quantity and type of flocculant used in the filtration process, the thickness and the grading analysis of the sand beds and the quality of supervision. An on-stream duty of approximately 0.15 gallon per sq ft of surface area is obtained. Hydraulic handling of clarifier sand, while cleaning, may effect the efficiency of a clarifier, as size segregation of sand particles may lead to inefficient "pockets" in a sand bed. Control of the solution level in the sand clarifier also affects the quality of the effluent. Exposure of the sand bed invariably causes a cloudy effluent. Recycling of the final and initial solution discharged before and after skimming the clarifier sand improves the clarification efficiency significantly. Post-precipitation of silica and possibly sulphate salts, after clarification, may give a false impression of inefficient clarification. This phenomenon is more pronounced when treating hot supersaturated solutions. Ageing and cooling of the solution before clarification assist in stabilising the solution and reduce precipitation after clarification. The maintenance cost of sand clarifiers at Buffelsfontein is in the order of 0.35 cent per metric ton of solution treated. A redundant ion-exchange column has been tested successfully, either as a primary or a secondary clarifier, depending on the quality of the filtrate treated. The conventional pebble and sand beds in the column have been retained. Operation was enhanced by the addition of a two-foot deep resin bed as a filtering medium. The suspended solids content was reduced to less than 5 ppm. Mixer-settlers: Mixer-settler design is a controversial subject but, in view of the high costs of solvent compared to relatively low pumping costs, it is believed that mixing and pumping functions should be separated. Separate facilities for pumping and mixing not only give greater operational flexibility but also permit eventual changes in the flow circuit as technology develops. Scrub technique: Unlike the pilot plant, where the crud was carried away in the aqueous phase, crud is carried over with the organic phase in the full-scale plant. This carry-over of crud into the strip bank aggravates crud formation in the first strip stage. This phenomenon may result from a slight difference in settler design and/or a variation in the relative phase depths in the two plants. Bypassing of the scrub aqueous solution from the fourth to the second stage was introduced in order to avoid dilution and partial neutralisation of the acid added to the third stage, as it is known that a low pH value enhances the transfer of iron into the aqueous phase. The low aqueous flowrate in the third scrubbing stage was overcome by introducing an aqueous phase recycle. Gleaning: Mr MacDonald's contribution on "gleaning" was most informative. This process for recovering solvent from raffinate seems to show at least as much promise as coalescers and other methods employed to date. Similar tests conducted at Buffelsfontein pilot plant gave 60 per cent amine recovery from raffinate containing 10 ppm amine. However, the circuit was not operated at equilibrium and recovery may be expected to drop as the amine concentration of the "Gleaner" circuit increases.

By J. Levin, I. J. Corrans

Wet high-intensity magnetic separation (WHIMS) for the concentration of gold and uranium was tested on many Witwatersrand cyanidation residues, and on some ores and flotation tailings. The results varied, but many indicated recoveries of over 60 per cent of the gold and uranium. The main source of loss is the inefficiency of WHIMS for material of smaller particle size than 20fLm. The recoveries in the continuous tests were lower than those in the batch tests. The continuous tests indicated an operational difficulty that could be experienced in practice, namely the tendency for wood chips and ferromagnetic particles to block the matrix of the separator. It was decided that a solution to the problem lies in the modification of the separator to allow continuous removal of the matrix for cleaning. A system has been developed for this purpose and is being demonstrated on a pilot-plant scale. Promising results were obtained in tests on a process that combines a coarse grind, gravity concentration, and WHIMS. In the gravity-concentration step, considerable recoveries, generally over SO per cent, of high-grade pyrite. were obtained, together with high recoveries of gold and moderate, but possibly important, recoveries of uranium. A simple model describing the operation of the WHIMS machine in terms of the operating parameters is described. This should reduce the amount of empirical test work required for the optimization of operating conditions and should provide a basis for scale-up calculations. The economics of the WHIMS process is discussed.

Jan 1, 1979