Search Documents

By M. Steyn

The coordination compound tetrakis(1,3-diphenyl-1,3-propanediona to)zirconium(IV), [Zr(DBM)4], (DBM = dibenzoyl methane/1,3- diphenyl-1,3-propanedionol) was synthesized and characterized by single-crystal X-ray diffraction. [Zr(DBM)4] crystallizes in the monoclinic space group P21/c (a = 24.769(4) Å, b = 10.216(5) Å, c = 19.314(4) Å, and = 101.541(5)°). The coordination geometry around the zirconium atom, formed by the eight O-donating atoms of the four -diketonates, is found to be a near-perfect square antiprism. Crystal packing is stabilized by C?H... interactions throughout the crystal lattice. This structure is a noteworthy example of the application of ambient condition synthesis of zirconium compounds in N,N'-dimethylformamide (DMF) as reaction and crystallization solvent, highlighting the possibilities of aerobic condition metal purification through chelation.

Jan 1, 2014

By B. D. H. Knights

In November 2009 Mintek installed the FloatStar? advanced flotation stabilization system on Vale's Cauê iron ore beneficiation plant in Brazil. In September 2010 the system was upgraded to include flotation optimization. The circuit consisted of two parallel cleaner circuits producing final concentrate. The tailings from the cleaner section passed through a scavenger circuit. Large, well-instrumented feed sumps played an important role in circuit stability, presenting a good opportunity for advanced control. Previously the plant was controlled using distributed control system (DCS) level control only. The flotation circuit processes roughly 30kt/day. The FloatStar system provided advanced control of the flotation circuit as well as of the sumps feeding the circuit. The system underwent a lengthy trial to assess the benefit that it provided. Two data sets were analysed, showing performance under advanced stabilization and optimization respectively. Several validation and consistency criteria were employed to ensure the quality of the analysis. Iron recovery and iron tailings grade were used to measure system performance. The analysis showed that the system increased recovery by up to 2.7%. In addition, the system decreased the iron tailings grade by between 1.2% (from 23.5% to 22.3%) and 4.3% (from 31.3% to 27.0%) during different test campaigns. The analysis also showed that the entire FloatStar stabilization system was active for 72.7% of the time from first activation to the end of the first data set (approximately 200 days). From the analysis it was concluded that under similar conditions for 'ON' and 'OFF' tests, the system provides a clear benefit. It was also found that over the longer term, the system continues to provide a benefit. This finding suggests that the results were not simply due to a short-term advantage. The size of the data set, as well as the magnitude of the recovery improvements, lends considerable confidence to these results. Therefore, it can be concluded that the FloatStar control system provides substantial benefit to operations at this site.

Jan 1, 2012

By R. G. Diale, H. R. Chauke, T. M. Ledwaba, P. E. Ngoepe

FeCo alloys play an important role in soft magnetic materials with a wide range of technological applications due to their high saturation magnetization and Curie temperature. However, these alloys have low ductility at room temperature. The ductility can be improved by the ternary addition of elements such as V. A density functional theory supercell approach was used to generate B2 Fe50Co50-xVx (0 ≤ x ≤ 50) structures and the properties were evaluated at different atomic percentage compositions to determine the ductility at room temperature. The structures were fully optimized to obtain better equilibrium ground-state properties such as lattice parameters and thermodynamic properties for both binary and ternary systems. The stability of Fe50Co50- xVx was evaluated from the heats of formation, elastic properties, and phonon dispersion curves. Furthermore, magnetic strength was evaluated from magnetic moments. It was found that all structures are thermodynamically stable due to the negative heats of formation. The calculated Pugh’s ratio and Poisson’s ratio confirm that alloying with V effectively improved the ductility. It was also found that Fe50Co50-xVx showed a positive shear modulus for the entire concentration range investigated, in agreement with phonon dispersion curves. The ternary addition of V to the FeCo system resulted in reduced magnetic strength due to a decrease in magnetic moments. These findings reveal that B2 FeCo-V alloys can be used as components and actuators for the automotive industry.

Jun 10, 2024

By J. Arzuúa, U. Castro-Filgueira, L. R. Alejano, F. Malan

"Pillar design for underground mining is typically done using empirical formulae or numerical modelling. Practical experience and recent literature, nevertheless, illustrate the shortcomings of these design approaches. Ongoing monitoring of pillars is therefore recommended to minimize the risk associated with these designs.In a mine where a large number of pillars are cut, different pillar strengths can be expected owing to variations in rock mass strength from area to area. This problem is compounded by the fact that in mining environments the pillars are not always cut according to the prescribed dimensions. Although the original design using either empirical methods or modelling may predict stable pillars, unstable pillars will be encountered in reality. Very conservative designs with large factors of safety may circumvent this problem, but this approach is uneconomical.A possible solution to localized stability problems may be to enhance the strength of a few unstable pillars. It may even be hypothesized that reinforcing a few critical pillars may prevent ‘pillar runs’ on a much larger scale. Rockbolting, strapping of pillars, and pillar shotcreting have occasionally been used in the past as possible solutions. It appears that these have not been successful in all cases and large collapses have occurred in spite of the pillar remedial work.The authors investigated the strapping of pillars by conducting laboratory tests on cabled rock specimens. The results were qualitatively compared to actual attempts of pillar reinforcement available in the literature, as well as additional observations in an old haematite roomand- pillar mine in Spain. Based on these results, the value of steel cabling and mesh wrapped around pillars to improve stability is demonstrated. Some cases where this approach will not be successful are also discussed."

Jan 1, 2017

By N. Moemise, M. B. Shongwe, P. A. Olubambi, M. M. Ramakokovhu

"Near-infrared (NIR) spectroscopy sorting technology is incorporated in an automated optical mineral sorter that can discriminate between materials using the differences in characteristics when exposed to near-infrared radiation. During September 2014 to April 2015, a pilot plant that utilized NIR technology to discriminate between kimberlite and waste materials was commissioned to determine the viability of including this technology in the diamond winning process flow sheet at Cullinan Diamond Mine. The plant was used to minimize the waste content in the size fraction -70+35 mm that reports to the crushing section and then to the dense media separation process. This paper describes the initial test work, conducted at Mintek, that led to the decision to conduct a pilot-scale study. The mineralogical characterization of the feed and product streams to establish the sorting criteria and the operational data obtained during the pilot plant campaign are described. The results indicated a good possibility of discriminating between the kimberlite and waste material using NIR technology. However, the consistency of discrimination was not good enough to avoid the risk of potential diamond loss. Furthermore, a lower than expected availability of the machine reduced the throughput capabilities. IntroductionUsing near-infrared spectroscopy (NIRS) technology for ore sorting is a new concept for the mineral processing and mining industry. NIRS has been used for decades in the laboratory for the identification of pure minerals, and has its roots in the recycling, food, and pharmaceutical industries (Salter and Wyatt, 1991; Robben et al., 2009). Ore sorting in itself is not a new concept; it was introduced during the Stone Age with handsorting being the first method to separate valuable materials from gangue (Wills and Napier-Munn, 2006; Sassos, 1985). However, over the years the scale of mining has increased and hand-sorting has become challenging to implement (Joensson, 2014).Sensor-based sorting is an advanced technology that can help overcome problems such as ore dilution experienced in mineral processing operations. The benefits are lower energy and water costs, reduced ore dilution, lower environmental impact, and improved profit margin (Mathew, 1974; Jonsson, 2014; Salter and Wyatt, 2009; Death et al., 2009). In sensor-based sorting, materials are mechanically sorted based on certain physical properties that are detected by a sensor (Dalm, 2013). Research has found that with NIR scanners it is possible to obtain a ‘fingerprint’ of a sample that is directly related to its mineralogical composition. According to Woutruba et al. (2009), molecules absorb NIR radiation by means of electronic and vibrational transitions. Nowadays, there are many sensors available in the market that utilize different material properties; the choice of a sensor is dependent on the mineralogy of the ore."

Jan 1, 2016

By L. A. Maseko

"As part of the mining engineering curriculum, students are required to be placed in industry for vacation work or work-integrated learning (WIL). In this paper we review work-based placement as done at the four South African mining schools: the University of Johannesburg, the University of Pretoria, the University of the Witwatersrand, and the University of South Africa.Key aspects of past and current WIL (pre- and post-graduation) practices that may need attention are highlighted for consideration by all universities that provide professional qualifications. Work-directed theoretical learning, problem-based learning, project-based learning, workplace learning, and simulated work experiences are discussed as legitimate approaches to WIL.Regardless of the choice each institution makes, commitments of universities, preparedness of university teachers, and the desire for equity and excellence will play an important role in the provision of WIL.DefinitionsAccredited Qualification: a qualification awarded on successful completion of an accredited programme.Advisory Boards (or Committees): are essential infrastructure for a WIL curriculum that is built on the integration of the workplace and the university. This requires the collaboration of experts from both environments. Workplace advisors are critical to the success of the academy as they embody expert knowledge of the ‘real world’.Assessment: the process of determining the capability or competence of an individual against standards by evaluating performance.Category: a mode of registration defined in or under the ECSA Act which has a distinctive purpose, characteristic competencies, defined principal routes to registration, and educational requirements.Experiential learning: (in South Africa sometimes used synonymously with work placement or cooperative education) is a term used with a great variety of meanings in the international literature. More broadly, it may refer to learning that has meaningful learner involvement. It is the process of generating meaning from direct experience. In the international literature, experiential learning is learning through reflection on doing, which is often contrasted with rote or didactic learning."

Dec 1, 2018

By G. M. Evans, S. Mitra, G. J. Jameson, M. M. Hoque, E. Doroodchi, R. Moreno-Atanasio

In this study, the detachment behaviour of 314 μm diameter silica particles from a single 3 mm diameter bubble rotating in a confined cavity connected to a cross-flowing water channel was investigated. The liquid cross-flow generated a rotating flow inside the confined cavity, which was quantified using 2D particle image velocimetry (PIV) measurements. The fluctuating (x-y) velocity components inside the cavity for each cross-flow velocity, U, were then used to estimate the corresponding time/volume average turbulence intensity values, Ti. Turbulence intensity ranged from 9.3-16.2%. In the absence of a bubble, the rotating vortex within the cavity created a pressure field which decreased towards the centre of the vortex; wherein the lowest pressure zone was located at the centre of the cavity. The vorticity into the cavity was found to increase with increasing the turbulence intensity. A bubble, both without and with particles attached, was introduced into the cavity under different flow conditions and its motion was tracked using the shadowgraphy technique. Experimentally, it was found that the bubble-particle aggregate was trapped at the centre of the cavity (low-pressure region) following a spiral trajectory. An interface resolved 3D computational fluid dynamics (CFD) model was developed to predict the particle detachment conditions within the confined cavity. CFDpredicted vorticity in the absence of a bubble agreed well with experimental observation. The CFD analysis indicated that the vorticity inside the cavity was not significantly changed when a single bubble was introduced. On this basis, the computed vorticity was utilised in describing the force balance applied to the attached particle. Computationally, it was found that the critical turbulence intensity, beyond which the particle was detached from the bubble, was 14%. This value was consistent with the experimental observation of detachment at Ti at 15.7%, and above, but not at lower values. Keywords: Bubble, particle, turbulence intensity, vorticity, particle detachment, CFD, PIV

Jan 1, 2020

By T. Szendrei, S. Tose

The Gurney approach to explosive/inert material interaction was adapted to analyse the face velocity in bench blasting. The model is based on the blasthole diameter, rock and explosive density, burden, spacing, linear charge density, and the Gurney energy constant. It is validated by comparing its predictions with a set of 20 field measurements of face velocities reported by Chiappetta et al. (1983) in an iron ore mine. The Gurney model links the observed large scatter of measured face velocities to the variation of the Gurney energy constant. This in turn is linked to the variability of the gas pressure acting on the burden. These variable pressures are generated when detonation product gases migrate into the extensive and complex fracture network around and between in-row blastholes. The energy efficiency of burden movement can be derived from the model. It is shown that ~7% of the explosive’s chemical energy is available for gas expansion work on the burden; of this quantity, 36% is actually converted to burden kinetic energy. That is, less than 3% of chemical energy is ultimately expended in burden displacement and throw. The model further indicatesnthat the projection of high-velocity (say, 100 m/s) flyrock is possible only when the path of leastnresistance through the burden has an effective density far less than the host rock. An equationnis derived that identifies the combinations of burden and path density that may yield flyrock. These values are specific to a particular baseline blast design.

Jan 30, 2026

By C. J. Badenhorst

The primary focus of management today is safety, or preventing negative, generally irreversible, events of acute duration. The outcomes of safety-related events are usually visible and can evoke strong emotions if the results are severe. Experts now see that occupational illness and disease also result in significant emotional and financial toll to workers, their families and communities, and to their employers. Effective health and safety management must include acknowledging the importance of occupational health hazards and the proportionate application of resources to address those issues. Improvement in workplace conditions and decrease or elimination of illness and disability are due to actions within the workplace and result from the implementation of risk prevention and control measures. However, success may only be visible months or years later and may require interventions that have to be maintained over prolonged periods. This demands continuous, co-ordinated effort to ensure sustainability of diverse occupational health programmes and the relevant management systems. Too often occupational health is not seen as being part of the general management of business, but rather the function of a medical practitioner somewhere off site in a clinic. Integration of occupational health management systems with other management systems within an organization is essential for its success.

Jan 1, 2004

By S. Kauchali

"Underground coal gasification (UCG) is recognized as an efficient mining technique capable of chemically converting the coal from deep coal seams into synthesis gas. Depending on the main constituents of the synthesis gas, chemicals, electricity, or heat can be produced at the surface. This paper provides a high-level graphical method to assist practitioners in developing preliminary gasification processes and experimental programmes prior to detailed designs or field trials. The graphical method identifies theoretical limits of operation for sensible gasification within a thermally balanced region, based primarily on the basic coal chemistry. The analyses of the theoretical outputs are compared to actual field trials from sites in the USA and Australia, with very favourable results. A South African coal is studied to determine the possible synthesis gas outputs achievable using various UCG techniques: controlled retractable injection point (CRIP) and linked vertical wells (LVW). For CRIP techniques, an important result suggests that pyrolysis, and subsequent char production, are important intermediate phenomena allowing for increased thermal efficiencies of UCG. The conclusion is that South African coals need to be studied for pyrolysis-char behaviour as part of any future UCG programme. The results also suggest that UCG with CRIP would be a preferred technology choice for Bosjesspruit coal where pyrolysis dynamics are important. Lastly, the use of CO2 as oxidant in the gasification process is shown to produce syngas with significant higher heating value. Introduction and literature surveyCoal is a commonly utilized fossil fuel, providing over 40% of global electricity demand and about 90% of South Africa’s primary energy needs. However, less than 20% of the known world resources are suitable for possible extraction using conventional surface and underground mining techniques (Andrianopolous,, Korre, and Durucan, 2015). Underground coal gasification (UCG) has the potential to recover the energy stored in coal in an environmentally responsible manner by exploiting seams that are deemed unmineable by traditional methods. The UCG process, if successfully developed, can increase coal reserves substantially. For example, in the Limpopo region of South Africa alone, the estimated potential for UCG gas, based on existing geological records, is over 400 trillion cubic feet (TCF) natural gas equivalent – this is about a hundred times more gas than the existing 4-TCF Pande-Temane natural gas field reserve in Mozambique (de Pontes, Mocumbi, and Sangweni, 2014)."

Oct 1, 2018

By D. V. J. W. Groenewald, T. M. Louw, L. Auret, S. M. Bradshaw, A. V. Cherkaev

Unexpected equipment failures lead to financial losses due to production disruption. Time-based maintenance, based on checks over regular time periods, has been employed to minimise disruption. However, the improvements it can offer are limited as it may lead to unnecessary service of healthy equipment or missed failures occurring between service intervals. Condition-based maintenance (CBM) provides a further improvement to equipment reliability by detecting faults and predicting remaining useful life (RUL) based on equipment health monitoring. Its application in the mineral processing industry is hindered due to the high cost of health monitoring equipment. In this study, two stochastic process models, the adaptive auto-regressive model and the gamma process, are compared in their ability to forecast the degradation state and to provide RUL prediction. The gamma process model was found to be effective in both tasks. Due to its simplicity and minimum hyperparameters requirements, it is proposed to use the gamma process as a baseline for comparison with other models. Keywords: Condition-based maintenance, remaining useful life, slurry pump, adaptive autoregressive mode, gamma process

Jan 1, 2020

By T. Szendrei, S. Tose

The generally accepted view in rock blasting is that the sources of energy for the fracture and movement of rock reside in the shock wave and gas action resulting from the explosion, and yet the mechanisms by which these sources interact with the rock have remained unclarified. It has also been noted that up to 50% of the work capacity of an explosive released in a blast cannot be accounted for by field measurements of energy partitioning. In this study, we describe a physical model that details the response of rock to both shock wave and gas action. An analytical model based on momentum conservation is derived to describe the dynamics of shock-driven expansion of the blasthole. Radial expansion of the hole is the key parameter that permits the derivation of the following characteristics of rock response to shock loads: hole expansion time; volume of displaced rock; energy consumed per unit volume; expansion energy efficiency; stress wave pulse length; gas pressure in enlarged hole. Soon after the completion of hole expansion, the shock wave degenerates to an elastic stress wave that runs through the burden. Blasthole expansions of between 50% and 300% of diameter are completed in under 1 ms and, depending on rock properties, consume 32% to 42% of the detonation energy or about 55% of the available mechanical (Gurney) energy. Gas pressure in the enlarged holes in five rock types is between 35 MPa and 650 MPa, and drives the mass movement of burden rock.

Oct 9, 2024

By T. Matlou, S. Myendeki, V. Midzi, T. Zulu, H. Mabotja, T. Mulabisana, B. S. Zulu, L. Hlatshwayo, T. Makhateng

The Council for Geoscience (CGS) performed a macroseismic investigation following the occurrence of an earthquake in the Boksburg area on 11 June 2023. The event had a magnitude of ML 4.4 and a focal mechanism that showed the event as having strike-slip motion along a northwest-southeast oriented fault. The event resulted in aftershocks, some of which occurred away from the causative fault in the east in an area without a mapped fault. However, the cluster of past events in that area suggests that there is an active fault. Due to the size of the main earthquake, a macroseismic survey was conducted to determine its impact on the community in the region. Analysis of observed data obtained from questionnaires resulted in the creation of 153 intensity data points. Their distribution showed high intensity values close to the earthquake source area. However, the investigation highlighted a number of anomalies, such as the higher than expected intensity values observed far from the event epicentre. It could be that these anomalies are caused by site conditions, for example, amplification of ground motion due to thick soil layers.

Jan 12, 2025

By I. O. Ondicho, E. K. Mutinda, B. O. Alunda, E. Agyekum

Driven by the necessity to improve blast performance regarding fragment size distribution in limestone mines, this paper introduces the prediction and measurement of blast fragmentation distribution through the modified Kuz-Ram (MKR) and Kuznetsov-Cunningham-Ouchterlony (KCO) models. Precise prediction and measurement of rock fragmentation resulting from blasting play a critical role in hard rock ore extraction. This is due to the substantial influence of post-blast ore size distribution on the efficiency of all subsequent downstream rock handling and processing operations. Additionally, employing secondary breakage of boulders, when necessary, leads to an unjustified rise in production costs. In this paper, the MKR and KCO models were utilised to identify the most appropriate model for application in Bisil and Simba quarries situated in Kajiado County, Kenya. Split-Desktop was used for blast fragment measurement by processing digital images obtained after blasting and computing the fragment size distribution of the blasted rock. As per the investigation, the recorded percentages of boulders generated at the sites ranged from 7% to 12.3% for the Simba quarry and from 11.2% to 23.9% for the Bisil quarry, respectively. Regression, correlation, and root mean square error (RMSE) were employed as the primary performance indicators. The study concluded that KCO outperformed MKR in accurately predicting blast fragment sizes in the examined quarries.

Mar 5, 2025

By R. Dehghan, M. Zarei, A. Tohry, S. C. Chelgani

Typical depressants for selective reverse flotation of iron oxides from complex silicates do not generally show high levels of efficiency. Therefore, as a hot topic, there are several ongoing investigations in this area. The main aim of this paper is exploring the potential of using humic acid (HA) as a depressant in reverse cationic flotation of hematite from complex silicates. For such a process, the wettability and flotation behaviour of pure minerals (hematite and silicates) was investigated at pH 10 in the presence of HA and cationic collector. Adsorption mechanism of HA on these minerals was measured by zeta-potential and FTIR. Results of flotation tests showed that at the lower concentrations of HA, selective separation of silicates from hematite is beneficial, where the floatability of amphibole was higher than pyroxene. A higher separation efficiency of hematite through reverse flotation was observed in the presence of amphibole, in comparison with the presence of pyroxene. Wettability studies showed that HA has a significant effect on reducing the hydrophobicity of treated minerals with the collector. The adsorption, ZPC and FTIR test results indicated that HA was adsorbed on both silicates and hematite. However, the absorption intensity onto hematite was much higher than silicates. It was found that the adsorption mechanism of HA on hematite takes place through both strong H-bonding and ligand exchange. Keywords: Reverse cationic flotation, humic acid, iron oxide, complex silicates, surface adsorption

Jan 1, 2020

By M. S. Shishvan, S. Klerkx, J. Sattarvand

The inaccurately drilled blastholes from the planned locations cause changes in the spatial distribution of explosive energy; some areas of the blast may receive a surplus of explosive energy, while others see a reduction. This results in less uniform fragmentation, reduces the efficiency of mining operations and increases costs. Additionally, it can lead to slope stability issues, flyrock, and uneven benches. To mitigate these problems, this study attempts to reduce differences in the explosive energy distribution (EED) through an optimization approach that adjusts the height of explosive columns in blastholes. Two optimization algorithms, the Genetic Algorithm (GA) and Tabu Search (TS), are tested. The latter is preferred for its local search neighbourhood strategy that gives superior computation times. Applications on different blast patterns result in improvements of 0.53–1.54%, or 2.14–3.94% when only the affected blocks are considered.

Sep 1, 2021

By J. Sepulveda

"Despite the recognized influence of product fineness on line capacity and downstream process performance, few mineral concentrators today use particle size measurement of the final product in automatic control applications for particle size. ‘Near-line’ particle size instrumentation has existed for decades and is utilized in modern concentrators, but low availability and measurement frequency, due to problems with slurry sampling and transport systems, make these technologies unreliable for use in automatic control. An innovative technology for real-time particle size measurement on individual hydrocyclones, named CYCLONEtrac™ PST (particle size tracking), has been developed by CiDRA Minerals Processing, and proven in commercial installations, demonstrating near 100% availability with minimal maintenance requirements, thus overcoming the limitations of previous technologies. Potential stakeholders require convincing, reliable information regarding the economic value delivered by automatic grind control projects. In this paper we present a methodology for estimating such value with the CYCLONEtrac™ PST technology, and demonstrate unique opportunities to improve process stability and performance. Based on actual plant data accumulated over time, the evaluation approach assesses and highlights the significant potential process improvement that can be expected with the particle size tracking technology. As an extension of previous work, in this paper we present the key operating criteria for optimizing the production of valuable metals and increase mill throughput by identifying the optimal grind size. As this requires operating closer to the process boundaries, accurate real-time particle size measurements, such as those provided by the CYCLONEtrac™ PST system, become essential for achieving the maximum potential value from every operation. For further illustration, data from three different copper plants is compared.Introduction Owners and operators of mineral concentrators constantly search for the most economically attractive way to increase the output of valuable metal. A logical approach is to identify a key parameter that has the greatest impact on the performance of multiple stages of the process and then use a holistic analysis methodology to determine how this key parameter can be controlled to optimize the final output.Particle size is widely recognized as such a key parameter; however, very few concentrators today use real-time particle size measurements for automatic control of the final product size due, to a large extent, to the inherent limitations of existing technologies. ‘Near-line’ particle size measurement instrumentation, which has been used for decades, typically suffers from low availability because the fundamental measurement technologies were developed for other, less demanding industries and then adapted to the harsh environment of the typical mineral concentration process. An outline of the key differences among the available technologies used for particle size measurement in comminution circuits has been completed in previous work, and plant data has proven the benefits of measurements on individual cyclones – something that, until now, has not been possible (Cirulis, 2017)."

Nov 1, 2018

By J. F. Brand, J. C. van Dyk, F. B. Waanders

"Syngas from Africary’s Theunissen underground coal gasification (UCG) project will be used for power production and synthesis of liquid fuels and commodity chemicals. However, some of the coal components, especially condensable water, oils, tars, inorganic trace elements, and a small fraction of fly ash and particulate matter, make their way to the surface via the production well and can cause adverse impacts on downstream processes. Africary’s standard design incorporates a cold gas clean-up system that relies on relatively mature techniques based on highly effective wet scrubbers and acid gas removal (AGR) systems such as Rectisol®, but with the downside of low energy efficiency and waste water generation. In this paper, novel technologies for removing contaminants and species separation from the hot (T > 300°C) raw syngas are compared. Comparisons are made between supersonic gas separation (SGS), Ranque–Hilsch vortex tube (RHVT), vortex gradient separation (VGS), and inertia vacuum filtering (IVF), and a vortex-based gas separation concept is proposed for UCG applications. IntroductionImpurities in gasification feedstock (coal, biomass, waste, etc.), especially sulphur, nitrogen, chlorine, and inorganic mineral matter, often end up in the syngas and can cause adverse impacts on downstream processes. Africary’s standard design incorporates a cold gas clean-up system that relies on relatively mature techniques based on highly effective wet scrubbers and acid gas removal (AGR) systems such as RectisolR, SelexolR or aMDEAR; but with the downside of low energy efficiency and waste water generation.Hot (T > 300°C) gas clean-up technologies are attractive because they avoid cooling and reheating of the syngas stream. Some available warm gas cleaning technologies include traditional particulate removal devices such as cyclones, candle filters, membranes, and molecular sieves. The warm gas desulphurization process technology developed by RTI LLC (2018) requires hot syngas to remove sulphur and has become commercially ready. Many other hot gas cleanup systems are still under development, given the technical difficulties caused by extreme environmental and operating conditions."

Jan 1, 2018

By S. Andika, O. A. Putri

Maintaining fleet productivity, which consists of balancing loader and truck performance, has always been a challenging task. An automatic dispatching system (ADS) is implemented to help monitoring fleet condition and assign trucks to a designated loader. Integrated data from real time Global Positioning System, Vehicle Health Monitoring System, and other production related data are acquired to support the ADS. However, the abnormal truck cycle has been the main culprit which resulted in unnecessary loader hanging time and trucks queuing time. Hanging and queuing time accounted for 2.34 and 2.07 minutes respectively per loading cycle or equal to 2,861 loose cubic metres per fleet per day production losses. Using integrated dispatching system data, the authors conducted research to study a truck’s hauling cycle that affects fleet productivity. The data is modelled to obtain the arrival rate pattern in a front loading area by adopting the queue theory algorithm. This paper aims to understand the potential pattern of a truck’s cycle abnormality and to resolve its occurrence.

Sep 1, 2021

By N. P. Mabasa, N. Naudé, A. M. Garbers-Craig

An improved methodology is presented for assessing the economic feasibility and effectiveness of recycling MgO-C and Al2O3-MgO-C refractory bricks, which are widely used in the steelmaking industry. Since approximately 28 Mt of refractory bricks are discarded each year, it is logical to recycle them. When furnaces and ladles are relined, the spent refractory bricks become mixed up, and need to be sorted before recycling. This study examined the use of a hand-held X-ray fluorescence analyser (HH-XRF) to distinguish between spent oxide-based and oxide-carbon-based refractory materials, with special emphasis on spent MgO-C (MC) and Al2O3-MgO-C (AMC) bricks. HH-XRF analysis was conducted on 18 oxide-carbon refractory bricks as well as on MgO-chromite and bauxite-based refractories. X-ray diffraction, reflected light optical microscopy, and scanning electron microscopy with energy dispersive spectroscopy were used to characterize the MgO-C and Al2O3-MgO-C bricks to confirm the accuracy of the HH-XRF analyses. This study also underlined the importance of calibrating the HH-XRF analyser for the refractory bricks to be sorted. The HH-XRF was successful in distinguishing between the different oxide-carbon-based refractory bricks both before and after cleaning. This result is important as it proves that HH-XRF provides a method whereby spent MC and AMC bricks can be sorted quickly and reliably.

Jan 26, 2023