Search Documents

By S. Parada, P. T. Jones, M. Guo, S. Smets

The corrosion behaviour of a high-quality rebonded magnesia-chromite refractory in contact with a vacuum oxygen decarburization (VOD) slag with high Al2O3content (15?20 mass per cent) is investigated under VOD process conditions by rotating finger tests in a vacuum induction furnace. The refractory degradation mechanisms are studied by the characterization of corroded microstructures using scanning electron microscopy, equipped with energy dispersive spectroscopy. The influence on the refractory wear of the process temperature and the Al2O3content in the slag is discussed. Keywords: corrosion, magnesia-chromite refractory, VOD slags, vacuum induction furnace

Jan 1, 2004

By D. S. Dihalu

A generalization of Gy?s model for the fundamental sampling error introduced the new ?parameter for the dependent selection of particles?, denoted as Cij. This allows for modeling deviations from the ideal situation where the selection of a pair of particles is composed of two independent selections. The generalized model potentially leads to more accurate variance estimates in the case of clustering of particles, differences in densities or sizes of the particles or repulsive inter-particle forces. A straightforward and practically applicable method is needed for the determination of this parameter for miscellaneous mixtures in industrial settings. In this contribution, the feasibility of using digital image analysis to determine this parameter Cij, will be demonstrated. Line transect sampling of a digital image was used to construct a transition probability matrix. A new algorithm to derive quantitative estimates for Cij will be presented and discussed. The applicability was verified by a photograph of zirconium silicate particles of sizes typical for industries dealing with pharmaceutical, food/feed, and environmental applications. Conditions affecting the practical applicability are identified and potential pitfalls will be discussed, including e.g. how a potential unrepresentative surface can affect the quality of the estimate of Cij.

Jan 1, 2010

By M. A. Kujoana

Following on the design of good mining layouts and regional support systems, and the implementation of sound strata control practices, stope support is the ultimate strategy to combat the hazards of rockfalls and rockbursts. The primary function of stope support in intermediate and deep level mines is to stabilize the rock mass immediately surrounding stoping excavations, that is, the zone of fractured rock which behaves in elastically around stopes. Support design is a process resulting in a support system which is both practical and meets or exceeds by a factor of safety the requirements for a particular geotechnical environment. The aim of this project was to design a support system, which accommodates the factors of rockfalls and rockbursts. The pack support unit must be easily handled, less costly and can be used in stopes without any significant convergence. The project tested the structural stability of packs to their expected deformation, in order to design a height to width ratio for stopes where little convergence is expected.

Jan 1, 2009

Viscosity measurement was carried out over a narrow range of silica content around the fayalite composition. A wide range of temperature and oxygen potential was covered where the slag was completely liquid. In order to keep the slag composition and the Fe3+/Fe2+ratio constant, theCO2/CO ratio was kept constant as the temperature was varied. Increasing the Fe3+content has little effect on viscosity for slags with a silica mole fraction of 0.31. At higher silica contents, increasing the Fe3+content brings about a small decrease in the viscosity.

Jan 1, 2004

By R. Lombard

"Water is a very important component in the production process at underground coal mines. Current unfavourable economic conditions have forced the coal mining industry to identify and address every possible bottleneck preventing optimal production. An increase in water-related downtime was identified as one of the bottlenecks at Goedehoop Colliery’s Vlaklaagte Shaft. The purpose of this project was to identify the various causes that contributed to the high downtime (501 hours in 2013, which led to a potential profit loss of R12.9 million) and to suggest possible solutions.After a thorough investigation the main causes of water-related downtime were identified as low water pressure and low water flow caused by pipe leakages and bursts. The main root cause for the low water flow and pressure was identified as being the low pressure resistance (1600kPa) of the thin-walled galvanized steel pipes used in the underground inbye water reticulation system. The pipes were selected according to the previous 1000 kPa pressure requirement for the continuous miner. However, the pressure requirement changed to 1500 kPa, which resulted in the pipes being exposed to much higher pressures than designed for.The water reticulation system was reviewed and current and future underground pipe layout and water requirements were determined for the shaft. The time frame in which the water consumption would be the highest was determined to be between 1 January 2014 and 7 September2014. Machine and sprayer specifications were used to determine theater consumption at the shaft. Three different solutions were considered to solve the water-related downtime problem and to ensure the efficient supply of water to the newly open sections. Permanent underground concrete dams, semi-mobile dams, or new pipe columns with a higher pressure resistance of 3200 kPa were considered. A trade-off study (taking into consideration cost, time to completion and ease of implementation, maintenance requirements, safety, and flexibility) was completed to determine which of these solutions would be most viable.Paper written on project work carried out in partial fulfilment of B. Eng. (Mining Engineering)"

Jan 1, 2015

By J. C. Carrasco, M. Sánchez, R. Jara, F. Marquez, F. Parada, R. Parra, J. Palacios

In past years, Chile has been the largest copper producer in the world and for 2002 mining represented country average of 10 % of the GDP, accounting for 47 % of the total exportation. As copper sulphides are the main mining resources in the country, the metal is produced using the classical processes of flotation and pyrometallurgical extraction. Seven copper smelter plants, which extends from the northern Atacama desert to the central part of the country produced1,522,000 metric tons of fine copper in 2002, approximately one half of total copper concentrate production, with a notorious environmental impact due to the great amount of slag produced during these extraction steps. In this work, a global characterization of copper pyrometallurgical slags produced and disposed of in Chile and worldwide is done, and the concept of total project development is considered to explain the scopes of the study, recovering different compounds and generating new activities around mining. The presentation is completed with the proposal of various methods and techniques being developed today in a joint project between smelter plants and the University of Concepción, with the support of the Chilean government and mining companies, addressed to generate new materials from copper slag. Recovery of copper, molybdenum, precious metals, silica and iron, that is the most abundant component of the slag, are the goals for this research. Metals, commercial compounds, alloys and different forms of iron oxides for steel industry are proposed products.

Jan 1, 2004

By Y. Nakata, K. Nagata

Plasma is partially ionized gas composed of ions, electrons and activated elements at high temperature. Some flying ash from incinerated municipal waste is melted to become glass by a transfer-type arc plasma furnace. As the glass is ionic silicate, when an electric current passes through anode to cathode, ions in molten slag electrochemically react with electron in plasma at the surface of molten slag. In case of molten Na2O-SiO2, sodium ions in the molten slag carry electric current and SiO2are reduced to evaporate as SiO gas by electron in plasma. The cases of Ag+in NaNO3-KNO3molten salt and Fe2+in FeO-SiO2slag were examined. The amount of cathodic reaction is larger than that of anodic reaction and not apparently according to the Faraday?s law on the electrochemical reactions.

Jan 1, 2004

By R. E. Wilmot

This paper is based on the experiences, over many years, on the part of numerous authors in the South African mining industry and that of the hot dip galvanizing process and its application as a corrosion protection system. The paper sets out the extensive development, financial resources and stringent operating requirements of the South African mining industry. After many years of research and operational experiences, hot dip galvanizing and when necessary, duplex systems, have been found to meet the demanding requirements of this particular industry. The paper sets out the requirements from the standpoint of corrosion criteria and is followed with a practical example; ?case history? where the corrosion protection properties of hot dip galvanizing are demonstrated. This case history traces the early investigation of the expected corrosive conditions to be encountered in a new mining operation (now 10 years on) and concludes with two follow up visits to the mine in order to examine actual performance of the corrosion protection system after ten years in service.

Jan 1, 2006

By J. van der Merwe, D. Tharandt

The corrosion behaviour of 304L stainless steel laser-cladded with various amounts of ruthenium (Ru) was evaluated in solutions of sulphuric acid and sulphuric acid plus sodium chloride at 25°C and 45°C by open-circuit potential and cyclic potentiodynamic polarization tests. In general, the addition of Ru to the stainless steel increased its corrosion resistance in 1 M H2SO4, as well as in 1 M H2SO4 plus 1 wt% NaCl. This was observed for a number of parameters such as corrosion rate, corrosion potential, open-circuit potential, and current density. However, increasing the amount of Ru added beyond a certain level did not result in further improvement in corrosion protection. For each environment there is an optimal Ru concentration for the best corrosion protection. For example, in 1 M H2SO4 at 25°C, 2.44 wt% Ru shows the least active surface in terms of corrosion. Further research into ruthenium coatings on stainless steels is recommended.

Jan 1, 2015

By P. Turcotte, E. Karampinos, F. Mercier-Langevin

In some underground hard-rock mines, squeezing compressive ground conditions are influenced by the presence of rock foliation and high stress. In these cases, the orientation of the foliation with respect to the drift direction has a considerable impact on the magnitude of the resulting deformation. Irrespective of the reinforcement and support strategy, keeping drives developed sub-parallel to the rock foliation operational is difficult, and often requires excessive rehabilitation during the lifetime of the excavation. This study uses field observations and convergence measurements at the LaRonde and Lapa mines of Agnico Eagle Mines Ltd to provide guidelines of the anticipated squeezing levels at these operations.

Jan 1, 2015

Tunnelling under squeezing ground conditions poses significant challenges. There are fundamental differences in the choice of support for mining as opposed to civil engineering. This paper reviews ground support strategies that have been used to control large deformations in mining excavations based on field data from five different mines in Australia and Canada. Recommendations are made for improved ground control strategies in squeezing rock conditions.

Jan 1, 2008

By M. W. Hildyard

The aim of this paper is to demonstrate that active seismic measurements could have an impact in helping solve rock engineering problems experienced in the South African mining industry. The paper presents a variety of experimental and numerical results where seismic waves show clear differences in wave-speed and amplitudes due to different degrees of fracturing. It presents results from the ?Omnibus? project commissioned to develop new ultrasonic technologies for diagnosing fracturing for nuclear waste repositories. This included using models to investigate assemblies of cracks where the effects of crack density and crack size on waveforms are shown to be coupled. Results indicate that these effects can be decoupled in the frequency domain, where the Fourier amplitude aids in estimating crack size, while the low frequency phase-difference has a direct relationship to crack density. Models are also shown to aid interpretation of waveforms by isolating geometric effects from the effects due to cracks. Two rock engineering problems experienced in the South African mining industry are investigated through numerical examples. These demonstrate that determining whether ?crush? pillars have failed and determining the degree of fracturing in the hangingwall of stopes, may be possible through the use of active seismic surveys.

Jan 1, 2005

The key aspects of process metallurgy that distinguish platinum group metal (PGM) concentrate smelting from that of other base metal sulphide concentrates are presented. These differences include considerably higher input chrome and magnesia contents that directly raise the slag liquidus temperature and have the potential to increase accumulations of refractory spinels. Most importantly, the higher processing temperature required for PGM smelting, and the resulting very high matte superheat lead to considerably more onerous smelting conditions than those typical of other smelting operations. This has presented challenges to furnace design and integrity, especially when coupled with the progressive intensification of smelting, involving doubling, and then redoubling, of furnace power input over the past 20 years. These power increases have been enabled by increasingly more advanced furnace cooling and structural technologies. Key technologies include strong constant-force spring-loaded bindings acting in three dimensions to minimize infiltration of superheated matte into brick joints, and robust well-cooled tapholes for reliably tapping the superheated matte. The result has been substantially improved productivity, and reduced smelting capital cost outlay per unit of production. A significant challenge that was not anticipated, presented itself in the form of insidious corrosion of the furnace lining, and especially high-intensity copper cooling elements. Investigation of corrosion in related industries eventually identified 'chloride-accelerated sulphidation', and this term has been retained as it generically describes the most pertinent aspects of the accelerated low-temperature wear of copper coolers observed in PGM smelting. In addition to discussing the corrosion mechanism, this paper describes a number of solutions that were developed jointly by Anglo American Platinum and Hatch to address the copper corrosion problem. First, new monitoring technologies allowed furnaces to be operated more safely for a longer period of time. Second, a system for replacing corroded coolers from outside the furnace during a fast 'hot' shutdown minimized the impact on furnace operating factor and hearth life. Finally, a corrosion-resistant graphite-protected cooler design significantly improved furnace campaign life, and heralds a more lasting solution to cooler corrosion in PGM furnaces.

Jan 1, 2012

By D. F. Malan

This paper presents an overview of work conducted over several years to investigate the continuous stope closure profiles recorded in tabular excavations and the use of this data as a hazard indicator. In spite of the brittle nature of the rock, measurements in gold mines and intermediate depth platinum mines revealed a significant time-dependent closure component. Various approaches to simulate the time-dependent closure have been investigated. Viscoelastic theory is able to simulate the time-dependent closure behaviour, but there are subtle problems with the use of this theory as it cannot simulate the failure processes in the rock. To overcome these problems, continuum and discontinuum elasto-viscoplastic models were developed by the authors. Discontinuum models have the advantage of being able to simulate the creep behaviour of prominent discontinuities. Development of these models has led to useful insights into rock mass deformation and has made the numerical simulation of parameters, such as rate of mining, possible for the first time. A number of practical applications for the mining industry have been developed from this study. Among these are the delineation of geotechnical areas using closure data, use of the data as a hazard indicator and to give warning of large collapses in the platinum mines, identification of areas to be preconditioned in the gold mines, measurement of the effectiveness of preconditioning and improved da

Jan 1, 2007

By T. R. Curr, R. T. Jones

Keywords: Pyrometallurgy, Mintek, DC arc furnace, plasma, smelting, chromite, ilmenite, cobalt, slag, zinc fuming, dust, magnesium, laterite, ferronickel, arc modelling, Pyrosim, thermodynamics The Pyrometallurgy discipline at Mintek was initiated in the early 1970s, to support a growing ferroalloy industry in South Africa. In addition to a range of pyrometallurgical options, Mintek specialises in DC arc furnace technology and has pilot plant facilities up to 5.6 MVA, as well as a strong base in process and arc modelling. Industrial processes have been developed for ferrochromium production, ilmenite smelting, and cobalt recovery from slag. Recent work has been done on such processes as the production of ferronickel from laterite ores, the fuming and condensation of magnesium, and the recovery of platinum group metals from 'difficult' feedstocks.

Jan 1, 2006

By P. Gonzalez, C. Ariyo, L. Holappa

Oxidation state of titanium was determined in CaO-SiO2-TiOxslags in the composition range25–53 per cent CaO, 27–46 per cent SiO2, 10–55 per cent TiOxat 1873K using gas equilibration method. In the experiments, slags with different titanium oxide contents were equilibrated with a known carbon monoxide and carbon dioxide ratio. The results were used to determine the Ti3+and Ti4+contents as well as the activity coefficient ratio of corresponding oxides in the slag. The dependency of the activity coefficient ratio as a function of oxygen partial pressure was determined. Keywords: titanium, titanium oxide, activity, activity coefficient, slag iron, carbon monoxide,carbon doixide, gas, equilibrium.

Jan 1, 2004

By D. T. G. Emmett

[ ] South Africa, by a wide margin, is blessed with the largest known world reserves of platinum. The optimal use of these resources for the benefit of all South Africa?s peoples is a goal shared by industry, government and all South Africans. The challenge is to grow the industry in accordance with demand growth and thus to manage a long-term stable growth pattern for PGM usage world-wide. Amplats and the South African producers are well able to meet this challenge [ ] South Africa plays a critical role in the provision of Platinum Group Metals for world markets. In fact no other country has the productive capacity nor the geological reserves to supply the world?s platinum needs. The world required some 5 million ounces of Platinum in 1997 and South Africa supplied a full 74% thereof. The second major supplier, Russia provided a further 18% of world demand, primarily as a by-product of nickel production. Amplats satisfied about 37% of total world demand followed by Impala 20% and Lonhro at 12%.

Jan 1, 1998

By Wayne Burmeister, Danie Benade, Louis Meyer, Hugo Joubert

What is not measured cannot be managed. This is true of most things, including a furnace lining. This paper describes a Lining Management System used for this purpose. It provides the operations staff with a management tool to predict long term lining life and acts as a process optimisation tool. It alarms and records upset furnace conditions. Outputs from the system are described as presented through a specially developed software package and interface. It includes vertical and horizontal furnace sections showing estimated isotherms through the lining as well as the furnace bath. It also shows calculated heat flux values, estimated lining wear and the freeze layer profile. A novel three-dimensional display is described which provides the operator with a big picture view of the furnace crucible profile under real time operating conditions. The powerful trending facility for analysing both measured and calculated values is discussed. The required instrumentation hardware as well as the installation thereof is described, with special reference to an electrically insulating thermocouple socket design. Finally feedback is provided on the first year?s performance of the system installed on an open ferrochrome furnace at Assmang Chrome, Machadodorp, South Africa.

Jan 1, 2007

By J. G. Wiese

Reagents are added to the flotation process of Merensky Reef ores to achieve specific functions that enable the separation of valuable minerals from gangue minerals on the basis of the difference in their surface properties. However, due to the complexity of the process, the various interactions that occur as well as the incomplete liberation of the ore and range of minerals present, it is difficult to quantify the behaviour of each of the reagents. More specifically, changes made to achieve a particular outcome may have secondary effects that can override the desired effect. If all the effects and interactions can be accounted for, it is possible to manipulate reagent suites and obtain better overall metallurgical performance. This paper discusses the effect of the addition of copper sulphate at different operating points of the recovery of the sulphide minerals. Batch flotation tests indicated that the recovery of chalcopyrite was not affected when operating conditions were varied, whereas pentlandite recovery was strongly affected by the point of reagent addition, and pyrrhotite recovery was enhanced by copper sulphate addition, irrespective of the point of addition, with the extent being dependent on the ore source. Floatable gangue was activated by copper sulphate in the presence of the dithiophosphate collector. Froth stability was also affected by copper sulphate addition.

Jan 1, 2006

By H. Jalkanen, L. Holappa

The main role of slag in oxygen converter processes is to absorb the non-volatile oxidation products of hot metal impurities, Si, P, Mn, Ti, V, etc. The importance of converter slag as deP and de Smedia has ceased with implementation of special pre- and post-converter treatments. The transfer from top blowing (LD) to combined blowing converters has decreased the amount of slagged iron that, together with the tendency towards lower silicon and manganese contents, has decreased slag to steel ratio. Still the control of slag forming and behaviour during the blow is of great importance. In this paper the thermodynamics of the slag forming reactions, the role of slag in the modern oxygen converter process for impurity elimination, splashing, lining wear, dust formation and post combustion are discussed on the basis of common knowledge and experience of Finnish steel plants.

Jan 1, 2004