Search Documents

By James J. Dowd

The investigation to evaluate the reserves of coking coal in the United States suitable for the manufacture of metallurgical coke is being made by the Bureau of Mines in three parts: (1) To estimate known measured and indicated recoverable reserves of all coking coal; (2) to upgrade marginal coals through effective preparation; and (3) to study the carbonizing properties of coals and coal blends not now widely used for metallurgical coke making. This is the eighth of a series of reports giving the results of studies by counties under part (1) of the investigation. (See appendix.) This report covers Jefferson County, Pa., which comprises parts of Marienville, Hallton, Ridgway, Brookville, DuBois, Penfield, Smicksburg, and Punxsutawney quadrangles. (See fig. 1.) A short resume of the chemical and carbonizing properties of the coals is included. Data on the coal beds in the county were obtained from mining companies, land companies, individual landowners, and other sources of authentic information. A base map for each bed in each quadrangle was made to the scale 1 inch equals 1,200 feet. Maps of mines, locations of drill holes, bed and total coal thicknesses, and the outcrop of the bed were plotted on the maps. With all available data plotted, isopach lines were drawn to limit areas of known unmined reserves in beds 0 to 14 inches thick, 14 to 28 inches thick, 28 to 42 inches thick, and over 42 inches thick, These areas of coal reserves also were divided into "measured" and "indicated" categories. All areas in each thickness range and in each category, mined-out areas, areas excluded from the estimate, and areas outside of the outcrop were measured by planimeter on the base maps. Estimates of total reserves 14 inches and more thick and maps for individual beds were prepared from these data.

Jan 1, 1952

By James L. Eirls

Tracor MBA under a contract to U.S. DOI Bureau of Mines designed, developed, fabricated and demonstrated a conveyor belt service machine. It is self-contained, battery powered, rubber tired and capable of handling, storing and transporting conveyor belting, wire rope and associated structures for sectional conveyor belts. While moving the tail section to its next position the machine discharges the belting, wire rope and belt structures. The belting is elevated and separated to provide for the insertion of the structures with minimum expended effort. A hydraulic system provides the power for steering, braking, winding or unwinding under controlled tension the belting and wire rope, operating a load-bed slat conveyor, raising, lowering and locking connection hitches and powering external hydraulic tools. Also, a pneumatic system is available to operate air impact tools. The service machine, with its present components can function in coal seams as thin as 48 inches, double wind conveyor belting 42 inches wide, 400 feet long, load or unload 3/4" wire rope on two separate reels and is controlled by two operators. A complete belt move using this machine requires only four workers. Successful underground demonstrations were conducted in coal mines located in West Virginia and Kentucky.

Jan 1, 1983

By Kray Luxbacher, Erik Westman, Peter Swanson

Three-dimensional time-lapse velocity tomograms were generated to image stress redistribution around a longwall panel to produce a better understanding of the mechanisms that lead to ground failure. Mining-induced microseismic events provided passive sources for the three-dimensional velocity tomography. Surface-mounted geophones monitored microseismic activity for 18 days. Most similar studies have utilized active sources including longwall shearers, controlled explosions, and hammer blows. These active sources generally require a person to initiate and measure the location and time of the source, and are not conducive to continuous monitoring. This method utilizes mining induced microseismic events as passive sources and lends itself well to continuous monitoring. Two event location methods were compared in order to move toward quantification of tomographic results in terms of ground conditions. Additionally, LAMODEL was utilized to determine the expected stress distribution around the longwall panel and compare these images to the velocity tomograms. Eighteen tomograms were generated, one per day, and high velocity regions in the set of tomograms generated from the initial location algorithm correlated with abutment stress redistribution predicted by numerical modeling. This research is significant as it has the potential to improve safety in underground mines and is the only example of long term passive velocity tomography implementation for the purpose of inferring stress redistribution around an area of active mining. Though still immature, this technology has the potential to allow mine personnel to image areas of active mining on a regular basis and detect areas with anomalous velocity distributions indicating potential safety hazards.

By C. Hellar

A new dual-boom remotely controlled roof bolter was designed, fabricated, and then tested in an underground coal mine. Remote-control functions allowed complete bolting cycles to be performed on two booms with both operators located within protective cabs. Capabilities included 3-to 6-foot-long bolts in 5-to 8-foot seams, limited to bolts 20 inches shorter than seam height. Machine was in compliance with all regulations including dust collection, machine lighting, and permissibility.

Jan 1, 1979

This chapter summarizes data on crude mineral production for the United States, its island possessions, and the Commonwealth of Puerto Rico. Included also are tables that show the principal mineral commodities exported from and imported into the United States, and that compare world and U.S. mineral production. The detailed data from which these tables were derived are contained in the individual commodity chapters of volume I and in the State chapters of volume II of this edition of the Minerals Yearbook. Although crude mineral production may be measured at 'any of several stages of extraction and processing, the stage of measurement used In this chapter is what is normally termed "mine output." It usually refers to minerals or ores in the form in which they are first extracted from the ground, but customarily includes the product of auxiliary processing at or near the mines.

Jan 1, 1977

By Paul M. Price

The Mouat mine, Nye, Mont., was reopened in 1953 by the American Chrome Co. under a Defense Minerals Production Administration contract. Operations were terminated in 1961 after completion of the contract. Mining methods employed during this period are described in detail, and cost data are presented by years for 1953 through 1959. Ultramafic rocks of the Stillwater complex in Montana contain the largest domestic resource of chromite, and the Mouat mine has been the largest producer. Mine reserves were estimated in 1960 to be about 4.4 million tons containing 22.5 percent Cr2O3. The chromite deposits occur as a series of overlapping bands or lenses roughly paralleling the steeply dipping layers of the complex. Only two of the chromite layers have proven to be of economic importance. One layer is 2 to 16 feet wide; the other is 3 to 8 feet wide. Shrinkage stoping was generally used throughout the mine, but various methods of ore breaking, stope drawing, chute construction, etc., were tested to improve output and lower costs. Long-hole stoping proved to have limited use. Breasting down benches, developed outward from the center of the stope with air-leg drills, was satisfactory only in wider stopes. At the close of operations, the company had standardized the use of lightweight stopers to advance a flat back by breaking from a centrally located face. Mining costs were reduced 47 percent during 7 years of operation.

Jan 1, 1963

By Shail J. Butani

In 1986 the Bureau of Mines conducted a probability sample survey, Mining Industry Population Survey, to measure such employee characteristics as occupation; principal equipment operated; work location at the mine; present job, present company, and total mining experience; job-related training during the last 2 years; age; sex; race; and education. The population estimates are necessary to properly analyze the Mine Safety and Health Administration (MSHA) injury (includes illness and fatality data) statistics; that is, to compare and contrast injury rates for various subpopulations in order to identify those groups that are exhibiting higher than average injury rates. This report uses the survey's results to characterize the U.S. sand and gravel mining workforce from March through September 1986. Similar reports have been prepared for the metallic, stone, and nonmetallic mining industries, as well as for the entire metal and nonmetal mining (includes metallic, stone, sand and gravel, and nonmetallic industries) sector and the coal mining sector.

Jan 1, 1988

By Russell R. McLellan

Under the Heavy Metals Program, investigations were conducted at the old Badger dill placer mini in Nevada County California to collect data and information regarding drilling and sampling methods and deposit characteristics. The studies contributed to a team effort by five Bureau of Mines research groups to develop new or improved placer mining technology in the Tertiary gold-bearing channel gravel of northern California. This report describes the techniques used and the results obtained in the sampling and drilling stage of deposit delineation studies that were conducted by the Denver Mine Systems Engineering Group. Sampling included the collection and processing of 400 tons of largo and small volume samples from drill holes, underground workings, surface pits, and blast hole rounds. A total of 355 samples averaging 2,296 pounds per sample provided reasonably accurate data for analysis of the gold distribution. These studies indicate that the bulk of the gold is within 40 foot of bedrock in stacked, lenticular zones of cemented gravel that are largely confined to the relatively narrow, meandering course of the deepest portion of the bedrock channel. Drilling studies involved the testing of three types of truck-mounted drills including rotary, bucket and vibratory, none of which proved to be a completely versatile tool for sampling quickly and reliably both consolidated and unconsolidated gravel.

Jan 1, 2012

By Gergely Markos

Uranium mill tailings represent a potential threat to the human habitat by containing large amounts of radioactive and chemically toxic substances in high concentrations. These: undesired components enter the human habitat in various pathways such as by erosion and water or air transport. The main objective of this investigation was to evaluate the actual movement and model the potential movement of contaminants by seepage of water from the tailings into the subtailings soil. This report represents various models of the movement of contaminants using both theoretical approaches and empirical evaluation of data available from other investigations. The data consist of field measurements and laboratory determi¬nations of major and trace cations, the dominant anions, pH, and Eh of moist solids, extracts, and waters from the tailings and surroundings. Evaluation and interpre¬tation of data were accomplished by using Eh-pH diagrams, various statistical methods and the WATEQFC computer program. Data analyses show that the critical area of investigating movement- is the interfaces between tailings and the external environment. The chemical differences at interfaces seem to result in a sink system for contaminants. The tailings-soil¬-water system shows extreme complexities because of chemical and physical hetero¬geneity of the system preventing the use of a single comprehensive model to represent real conditions. The validity of the simplifying assumption used has been shown and increasing complexity has been built into the models. Analogs of these models can be used for evaluation of similar systems.

Jan 1, 1981

By K. Y. Haramy, R. O. Kneisley

This U.S. Bureau of Mines report summarizes a study of large-scale strata response to longwall mining at a western U.S. coal mine. This study utilized surface and subsurface measurements, geologic mapping, in situ stress measurements, and pressure cell readings to characterize strata behavior. Preliminary analysis of surface subsidence and time-domain reflectometry (TDR) was used to determine a suggested main roof caving sequence. Coal ejected from the face apparently resulted from brittle failures that occurred because of lack of significant yield zone development. The combination of a strong coal with pronounced directional behavior, low overburden pressures, a good caving roof, and a high-production environment that minimized time-dependent loading apparently reduced yielding of the longwall face. The panel 1 headgate-entry design appears adequate; however, the abutment pillar and adjacent panel tailgate rib are highly stressed and may contribute to problems during second panel mining. The small chain pillar yielded after passage of the face, but the pillar width may be near maximum since evidence of a stressed core exists.

Jan 1, 1992

By G. W. Jones

As part of its program for the promotion of safety, the Bureau of Mines has investigated various means of mitigating or eliminating the explosion hazards of combustible gases and vapors found in the mining and other industries. Knowledge as to the explosive characteristics of cyclopropane in air, oxygen, and other gaseous mixtures is of both theoretical and practical importance because cyclopropane is now used extensively in anesthesia. As such an agent it has many desirable characteristics, and increased consumption of this gas may be expected if the explosion hazards now attending its use can be minimized or eliminated. The present practice of using mixtures of approximately 20 percent cyclopropane and 80 percent oxygen should be discouraged because such mixtures are violently explosive and have led ,to fatal accidents.

Jan 1, 1940

By G. W. Jones

As part of its program for the promotion of safety, the Bureau of Mines has investigated various means of mitigating or eliminating the explosion hazards of combustible gases and vapors found in the mining and other industries. Knowledge as to the explosive characteristics of cyclopropane in air, oxygen, and other gaseous mixtures is of both theoretical and practical importance because cyclopropane is now used extensively in anesthesia. As such an agent it has many desirable characteristics, and increased consumption of this gas may be expected if the explosion hazards now attending its use can be minimized or eliminated. The present practice of using mixtures of approximately 20 percent cyclopropane and SO percent oxygen should be discouraged because such mixtures are violently explosive and have led to fatal accidents.

Jan 1, 1940

By Walter C. Woodmansee

The only reported mineral production in 1977 was small output of alluvial gold, valued at an estimated $54,320.2 In addition, marine shells are gathered for use in lime manufacture, although output was not reported. Proposed development of a bauxite mine and smelter, involving Rennell and Vaghena Islands, was deferred in June. Conzinc Riotinto of Australia Ltd. (CRA), in partnership with Mitsui Mining & Smelting Co. Ltd., and the Solomon Government, with- drew from the project, and Mitsui, which conducted a feasibility study and metallurgical testing of the bauxite, decided to defer further work because of slack demand for aluminum in Japan and difficulties in arranging financing. The Mitsui feasibility studies reportedly indicated that the project could be viable despite technical difficulties and relatively high initial investment costs. The project was to produce 1.5 million tons of bauxite and 600,000 tons of alumina per year from reserves totaling 60 million tans at 45% to 50% A1203.

Jan 1, 1981

By David Bendersky

This report covers a technical and economic investigation of old electrical power systems, equipment and practices being used in the metal/non-metal raining industry. The principal sources of information were the MSHA District offices, visits to representa¬tive mines and mills, equipment manufacturers and the literature. A list of 85 mines and mills, submitted by the MSHA Districts as candidates for this study, is given and their characteristics are analysed. The electrical power systems and practices at the 10 mines and 9 mills which were visited are described. The principal areas which do not conform to standard electrical practices are discussed with emphasis on the safety aspects of these practices. The costs to update electrical power systems and practices in metal/non-metal mines and mills are given. The principal findings of the study are summarized and recommendations are submitted.

Jan 1, 1980

By John H. Johnson

A study of mine air quality was conducted using the latest advanced continuous monitoring instruments. An overview of the various interacting variables in the mine that affect air quality is presented. One effort involves the evaluation of portable instruments, the development of measurement techniques, sample analysis procedures and computer programs for statistical analysis of measurement data, and the application of the instruments and techniques to the measurement of the concentrations of CO, CO2, NO, NO2 and particulate matter in a lead and a copper underground mine. A second effort involves the first application of the Mine Air Monitoring Laboratory (MAML), a mobile trailer containing laboratory type instruments, sampling and data systems for the measurement of CO, CO2, NO, NO2 and particulate matter. The data from the MAML for blasting and for operating diesel equipment are analyzed and presented in various plots.

Jan 1, 1977

By R. Marshall

Electrical trailing cable handling techniques and practices used in metal and non-metal surface mines were investigated by obtaining information through actual visits to the mine properties located in a variety of geological areas and climatic conditions. An analysis was made of all accidents related to cable handling which are cataloged by HSAC* for the period from 1971, through June 1980. Information was also collected from mine operators concerning near accidents and non-reported accidents. The results of this investigation were presented to the U.S. Bureau of Mines in an effort to outline recommended practices for cable handling in surface mines and to recommend additions and/or changes in the present regulations now being enforced by MSHA** field inspectors. These recommendations are also intended to assist the U.S. Bureau of Mines in evaluating the need for assisting the mine operators in the areas of training and distribution of information related to material handling of trailing cable. * Health Safety Analysis Center ** Mine Safety & Health Administration

Jan 1, 1980

This report is the 26th in a series summarizing Bureau of Mines research and technologic work on coal and related investigations and the 8th of these reports to be issued on a calendar-year basis.1 It reviews briefly work in progress during 1961, and it provides references to publications by Bureau personnel during 1961 and also to a few older papers that were not cited in prior reports of this series. Details about some of the researches mentioned may be obtained by referring to the publications cited in the footnotes or in the further list in the Bibliography; other phases of work are reported here for the first time and will be covered in more detail by later publications. The coal program of the Bureau of Mines extends over the wide range of applied and theoretical studies indicated by the table of contents of this report. Applied studies are conducted in connection with the development and evaluation of new mining techniques, and the effective processing and utilization of coal and coal products. Analyses of coal, technical advice, and other assistance to Federal agencies in connection with fuel and boiler-water problems, and health and safety activities are among the practical services handled by the Bureau, Fundamental research such as that on coal structure and on the properties of coal is conducted because it will, over a period of the, furnish an increasing general knowledge about coal; scientists and engineers may use this knowledge in solving problems in mining and utilization of

Jan 1, 1963

By Joan Weinberg

Real gross national produce (GNP) grew at a seasonally adjusted annual rate of 2.0% in the fourth quarter (table 1). The restrained quarterly growth rate was the slowest in 2 years, and was substantially slower than the 2.5 % rate of the previous quarter. According to the U.S. Department of Commerce, the summer drought reduced the fourth-quarter growth rate by 1.1 percentage points. A growing trade deficit and a reduction in business investment were the key economic factors curtailing growth. The trade deficit widened by $6.8 billion, reflecting both a surge of imports and a slowing of exports. Business investment declined 3.7%, mainly as a result of a slowdown in computer sales. On a year-to-year basis, the economy grew at an inflation-adjusted rate of 3.8% for 1988, the fastest in 4 years, despite the drought. However, on a fourth-quarter-to-fourth-quarter basis, real growth measured 2.7%. Increased exports and business spending for plant and equipment accounted for much of the 1988 GNP growth. Employment continued to grow as the manufacturing sector added 414,000 new workers (table 2). Of these, the primary metals industry added 26,000 workers, and the clay, glass, and stone industry added 10,000. The civilian unemployment rate remained low throughout 1988, fluctuating between 5.3% and 5.4% during the last quarter.

Jan 1, 1989

By R. Farrar

Protective canopies for conventional electric face equipment, including shuttle cars, operating in low coal (less than 48 inches) were designed, fabricated, installed and evaluated on in-mine machines engaged in regular coal mining operations. This work was performed under contract to the U.S. Bureau of Mines, Pittsburgh Mining and Safety Research Center. The canopies will support a vertical load of 18,000 pounds and provide protection against both roof falls and contact with the mine rib. Canopy configurations were established based on human engineering studies, full scale canopy mockups, and in-mine observation and consultation with mine and equipment manufacturing personnel. Overall height of each canopy is hydraulically adjustable between a minimum of 32 inches and a maximum of 40 inches. Canopy tops are open framework, welded structures, covered with expanded metal mesh. Structural members are 1 3/4-inch or 2-inch square tubing of AISI 413ON and ASTM A500 material, respectively. The canopy tops are typically supported by an understructure and upright post arrangement that is either integrated into the current operator platform or attached to the machine frame. The four upright corner posts house the hydraulic actuators. Canopy tops are elevated horizontally. Canopies are welded or bolted to the existing machines. Installation is accomplished with a minimal amount of interface modifications. No major machine design changes are required. Canopies were trial installed and load tested at the manufacturer's facility prior to installation on the in-mine machines. Canopies were installed on a Joy 14BU10 Loader, 16RB-3AH Cutter, and two 21SC Shuttle Cars, and a Galis 300 Roof Drill and 460-S Face Drill. Canopy installations were evaluated in the Jewell Ridge Coal Company No. 12 and Big Creek Tiller Mines. Operational time accumulated on the installations during evaluation ranged from 1 week to 14 weeks of two-shift operation. All five canopy designs, manufacture, and test were successfully accomplished. The five canopies met all safety requirements. Three of the five canopies were deemed to be completely successful from an operator's point of view. That is, mine management as well as the machine operator found that the canopies did not impede the operation of the machines to function with the same efficiency as before the installation of the canopies. The loader canopy, in fact, appeared to have provided a mole efficient operation of the loader by providing added safety to the operator from rib contact thus allowing him to concentrate more fully on the loading function. Operational problems were encountered with the shuttle car and the roof drill. The shuttle car canopy obstructed visibility to an objectionable amount and the roof drill canopy impeded maneuverability of the machine, more than doubling the roof bolting time.

Jan 1, 2012

By Keith S. Olson

During 1982 and 1983, the Bureau of Mines concentrated its fugitive dust control research on haulage road dust suppression by newer chemi-cals relatively unknown in the mineral industry, innovative dust control designs for haulage trucks, chemical tailing basin stabilization, and combined chemical and vegetation tailing basin stabilization. Relatively unknown dust suppression chemicals and innovative aerodynamic modifications to haulage truck fender designs were tested on a Minnesota sand and gravel operation haulage road. Magnesium chloride salt at 95-pct control efficiency and a petroleum derivative at 70-pct control efficiency were effective in suppressing dust generated by haulage vehicles; however, none of the fender modifications were successful. Commonly used dust suppressant chemicals were tested on a Minnesota taconite tailing basin to reduce the dust lift-off during the spring and fall dry seasons. The most successful chemical was lignin sulfonate with a seasonal cost of less than $200 per acre to achieve 90-pct dust control. When chemical treatments for immediate dust control were com-bined with revegetation for permanent control, the most promising chemical treatment based on vegetation response was lime-neutralized lignin sulfonate.

Jan 1, 1987