Search Documents

By R. T. Sorensen

Research and testing in a small scale equivalent of a commercial flota-tion plant was completed on four low-grade, iron-bearing materials from the western Mesabi range. Closed circuit-flotation of calcium-activated silica with fatty acid collector developed data for comparison with the batch process and highlighted problems not evident from previous bench testing. The four ore samples contained from 27 to 39 percent Fe and were equally represented by nonmagnetic taconite and semitaconite type materials. Iron concentrates containing 6.0 percent, or less, SiO2 were made 5, all four samples. Of the two material types, the semitaconite was the ore amenable to treatment, yielding iron recoveries of about 90 percent as cc pared with 70 to 80 percent for the other. Pilot plant tests showed that concentrate grade made in batch tests could be duplicated in the closed circuit and demonstrated that the amount of recoverable middling iron varied considerably between ore samples. The continuous tests also showed that water temperature strongly influenced results in the treatment of one ore but apparently was of indifferent consequence in another. Progress in thickening and filtration of flotation concentrates was made through introduction of tapioca flour to serve the dual role of iron mineral depressant and flocculant.

Jan 1, 1966

By L. H. Wullstein

Bureau of Mines research on methods for reclaiming land disturbed by the minerals sector of the economy has produced a specific procedure for effectively germinating seed of Indian ricegrass, a drought-tolerant plant valuable for reclaiming arid and semiarid sites. This report describes the procedure which consists of acid-treating the seed followed by temperature and light cycling treatments. Use of the procedure resulted in an average germination rate of 29 percent, ranging from 18 to 56 percent. Seed subjected to long cold treatment but with acid treatment yielded an average germination rate of 9.2 percent, ranging from 6.6 to 14.7 percent. Untreated seeds (controls) gave germination rates less than 0.1 percent.

Jan 1, 1979

By R. A. Friedel

THE UTILIZATION by the Bureau of Mines of infrared and ultraviolet-visible spectrometry in connection with coal research has led to some basic improvements in methods, including a calibration method, a quantitative assessment of infrared spectral energy sources, and the development and perfection of infrared filters and cells. The adoption of a micropipet method to flush organic samples into absorption cells permits the investigation of vapors from organic liquids and the identification of volatile organic compounds. The spectral method has been used to investigate the infrared spectra of metal chelates, the charge-transfer complexing properties of aniline and nitrobenzene, an infrared method for determining the presence of methane in coal-mine air that has been adopted for use in enforcing the regulations of the National Coal Mine Safety Act, and atmospheric pollution including smog and odor-causing oxidation and decomposition of organic materials. Correlation of spectra and structure of organic compounds, particularly aromatics, was studied.

Jan 1, 1966

By Lee Blackman

The Malheur-Jordan Resource Areas (MJRA?s) is a tract of approximately 6.5 million acres of federal and non-federal land in the southeast corner of Oregon. This study evaluated the Resource Areas' economically recoverable mineral potential based on geological estimates provided in the USGS report (Smith, 1994). The mineral terranes are believed by geologists to contain undiscovered resources. The geological data is probabilistic; with estimates of the possible number of deposits and their grades and tonnages. Possible future development scenarios range from no development to numerous mines. Based on the analysis performed on these terranes, the most likely (in a statistical sense) future scenario for the resource areas would include the potential for two medium sized, predominately gold, mines. These would supply direct and indirect employment of up to about a thousand workers.

Jan 1, 1995

By Russell R. Trengrove

The Copper Canyon lead-zinc mine is in the Battle Mountain. District, Lander County, Nev. It was discovered in 1866 and mined for copper until 1935 and for copper and gold until l948, when the main production became lead-zinc ore. The rocks in the area are carboniferous (Pennsylvanian and Mississippian) sedimentaries that have been intruded by quartz monzonite of Mesozoic age. They have been intensely folded, faulted, and tilted. Lead-zinc ore occurs as sulfides disseminated along fractured zones in a conglomerate arid hornfels. Development was carried out by the Bureau of Mines in cooperation with the U. S. Geological Survey and comprised a study of the geology, making maps and. cross sections, and exploring the deposit by diamond drilling from underground. Eighteen holes were drilled, for a total of 2,594 feet. This report contains a brief history of the property and a description of mining methods and beneficiation of the ore, geology, ore deposits and drilling done by the Bureau of Mines. It also contains detailed analyses of the ore samples taken and logs of the holes drilled.

Jan 1, 1951

By J. A. Organiscak

Quartz dust is one of the most significant ongoing health concerns in coal mining today. Since the early 1980's, the U.S. Bureau of Mines has conducted numerous studies in underground and surface coal mines to identify the sources of quartz dust and its fundamental characteristics. This report presents data and conclusions obtained from these studies. The two most significant quartz dust sources were found to be the continuous miner excavating rock and the highwall drill operating in a rock overburden. The percentage of quartz was found to be higher in the smaller size fractions of dust when significant amounts of rock were mined by the continuous miner. Another factor theorized to affect quartz dust generation and size characteristics is the morphology of the quartz-bearing rock. Several laboratory studies were conducted to investigate capture efficiency of water spray technology and flooded-bed scrubbers with respect to the particle size of the dust. Water sprays and flooded-bed scrubbers were both found to be less efficient on smaller dust particles, and the scrubber was particularly less efficient on quartz dust. These results indicate that quartz control technology should be directed at controlling smaller sized dust particles.

Jan 1, 1990

By Raymond M. Stateham

Calculations based on data obtained from measurements of smoke from coal-fired powerplants predict that infrared imagers will be useful tools for smoke vision. Infrared imagers operating in the 3-to 5-um spectral region have been evaluated for this purpose. A mine opening 110 meters long was filled with smoke from burning coal, and two men, wearing breathing apparatuses, moved through the smoke to serve as targets. The men were detected and identified at 80 meters.

Jan 1, 1976

By Albert L. Toenges

The State Division of Geology Arkansas Resources and Development Commission, and the Arkansas-Oklahoma Coal, Operators Association requested assistance from the Bureau of Mines in a study of coal-mining methods and practices in .Arkansas coal mines with the objective of reducing production costs. On October 7, 1946, a joint meeting was held by representatives of the Arkansas Resources and Development Commission, approximately 30 coal-mine Operators of the Arkansas -Oklahoma Coal Operaters Association, and representatives of the Bureau of Mines. The many problems confronting the coal industry in Arkansas, including mechanical mining in thin beds, costs, labor, and working time were discussed. Following this Meeting, a joint letter from Harold B. Foxhall, State geologist, and -P. R. Stewart, commissioner, Arkansas-Oklahoma Coal Operators Association, was addressed to Dr. R. R. Sayers; former ,Director of the Bureau of Mines, requesting that mining conditions in Arkansas be studied.

Jan 1, 1949

By Z. T. Bieniawski, R. K. Zipf

"Zipf Jr., R.K. and Bieniawski; Z.T., 1989. A fundamental study of respirable dust generation in coal. Min. Sci. Technol., 9: 87-99Black lung disease in coal miners induced by the formation of fine fragments of coal imposes very high human and direct costs. A fundamental understanding of the fracture processes leading to fine-fragment formation in coal by applying principles of fracture mechanics is presented. A four-step hypothesis is proposed which sequentially describes the mechanics of fine-fragment formation during a generic coal material—coal cutting tool interaction. These steps include: (1) development of a crush zone under the tool tip, (2) macrocrack propagation. (3) shear movement along macrocracks, and (4) additional fragmentation from shear. This model contains two sources of fine fragments, namely crushing under the tool tip and shearing along the macrocrack surfaces. Three critical assumptions are made that require experimentation. First, the coal material must contain flaws of sufficient density and sufficiently small size to liberate fine fragments by crushing. The following conceptual relationships are proposed between flaw size, spacing and fragmentation: first, the active flaw size must be less than the desired particle size and second, the spacing (or density) must be in the order of the particle size. The second major assumption is that a mixed mode fracture theory will describe the initiation and crack growth direction for the microscopic inherent flaws. The third assumption is that some degree of roughness damage, and interlocking exist along the newly formed macrocrack surfaces such that a small amount of shear movement along that surface leads to additional particle formation at a microscopic scale. Preliminary analysis of the mechanical regime under a cutting tool tip places order of magnitude bounds on the stresses strains, cycle time, stress rates and strain rates. Even though the tool moves and loads the coal material with considerable speed, a quasi-static stress analysis is applicable in this region.Introduction.The generation of fine fragments (respirable dust) during various coal mining processes may lead to the incidence of coal workers pneumoconiosis (black lung disease). The human and direct cost of dust-induced illnesses in coal miners is very large. By several. accounts [1,2] the Federal Government paid out about $12 billion to almost 500,000 coal miners and their beneficiaries between 1970 and 1980. In addition, several states and many coal operators have established their own compensation programs at costs ranging from a few cents to several dollars per ton of coal mined [2]. Since 1980, 'the present liability of the Federal disability trust fund has approached $20 billion and the benefit payments exceed $1 billion per year. There .are also hidden costs due to dust, in the form of increased equipment wear and decreased operator productivity, both of which are due to the poor operating environment. Quantifying these costs may be difficult; however, they may be in the same range as the present pneumoconiosis costs. These high human and direct dollar costs may be prevented or reduced through long term research efforts directed at understanding the generation and control of respirable dust and the incidence of black lung disease."

Jan 1, 1989

By Eliezer Kamon

To finalize the three years granted for the study of miners physiological responses to emergency situations, all the data obtained, were summarized into the following relevant sections; A.. Information on elements of the Man Test required under Subpart 4, Part 2, Title 30 in the Code of Federal Regulation (see Table M-T and Ref. I., Section A). B. Investigation on possible emergency activities, its simulation in the laboratory and the physiologic data obtained on miners performing them This included some studies under cool ambient conditions, expected to prevail in coal mines. C. While in section B the steady state responses have been obtained, time was devoted to establish a unit that will allow data gathering for non-steady state, i.e., transient responses to rapidly changing activities. Section B and C contained elements that were relevant to section A; the Man Test. Therefore some of the information described under section A Man Test, were actually measured during the battery of tests in either section B or in section C.

Jan 1, 1974

By Robert A. Speirer, Richard G. Burdick

Methods of detecting geologic faults and other linear features by means of processed LANDSAT satellite images have gained prominence during the past several years . There have been numerous programs written to pick these " lineaments , " but they have been almost universally tailored to large computers . This Bureau of Mines report describes a detection method developed for use with a minicomputer . The method comprises a suite of programs that scans an image for all " potential " lineaments . From this partially analyzed data , the final lineaments are picked by another routine . The method was field tested in an area of south- central Wyoming , and results indicated good agreement between computer- picked lineaments and ground features . Most of the known geologic faults in the area were picked by the method . Such features as roads and trails were also picked but were easily distinguished from faults during field inspection . The method is relatively new but promises to be a viable reconnaissance technique for the mining industry in geologic structural analysis .

Jan 1, 1965

By H. C. Miller

The success of any project in which gas is injected into oil-producing sands to increase the current rate or the economic ultimate production of oil or in which surplus gas from oil producing operations is stored temporarily in reservoir sands that have been wholly or partly depleted of their producible oil depends mainly upon an understanding of the underground movements of oil, water, and injected gas and the ability to control their speed and direction of migration through the reservoir sands. Many operators believe that injected gas always travels up the structure and drives oil to wells structurally higher than the injection wells, because the specific gravity of the injected gas is less than that of the fluid substances in the formation. Consequently, many injection wells are located on the flanks of oil-bearing structures with the idea of utilizing the energy of the injected gas to drive the oil to producing wells higher on the structure. It is true, under certain conditions of pressure and fluid depletion of the reservoir sands, that injected gas will move in an up-structure direction, but the theory that injected gas always moves up the structure is based on an erroneous conception of the laws that pertain to the expansion of gases. By definition, "a gas is distinguished by its property of infinite expansion and is limited in volume only by the walls of the vessel which contains it."3 The expansion of gas that is injected into reservoir sands also is limited by "walls" that surround the space influenced by the injected gas. The walls of the majority of undrilled or virgin oil-bearing reservoirs in California are the impervious shales overlying and underlying the productive strata and the "dams" or effective barriers of edge water around the rims of the reservoirs. When gas is injected into the sands of a producing reservoir, regardless of the location of the injection well on the structure or the degree of depletion of oil from the sands, one of the walls which confine the gas in the structure about the injection well is fluid. This wall will be edge water in a nearly depleted reservoir, where the drainage cones or regions of reduced pressure about injection and producing wells intersect; and, where there is no interference of drainage cones and the injection well is structurally above the edge water, the wall will be oil. In some producing reservoirs bottom water may be the lower wall of the space that confines the gas about injection wells, but the effect of bottom water on limiting the expansion of gas is the same as if the water was not present and impervious formation separated the producing from the underlying nonproducing strata. Therefore, since compressed gas always seeks regions of reduced pressure and its final volume is limited only by formation and fluid barriers and since the force exerted by the gas under pressure is equal in all directions, the course of migration of injected gas in reservoir sands in California and the

Jan 1, 1932

By D. C. Dahlin

The Bureau of Mines conducted laboratory batch beneficiation tests on samples from four potential platinum resources in southeastern Alaska to concentrate platinum and other precious metals. Thin Investigation was done as part of the mission of the Bureau to insure an adequate supply of minerals to meet the Nation's needs. Petrographic studies and beneficiation methods including gravity concentration, froth flotation, and magnetic separation were used to determine mineral association and to attempt to concentrate the platinum values with a primary mineral value such as chromite, copper sulfide, or magnetite. A high-graded sample from the Salt Chuck copper sulfide deposit yielded the platinum-group metal concentrate; the maximum grade attained was 0.04 oz Pt and 1.5 oz Pd per ton of high-grade copper sulfide concentrate. The other samples yielded low-grade primary mineral concentrates with low platinum-group values, and/or the platinum-group metals did not concentrate with the primary mineral value.

Jan 1, 1981

By James Westfield

This publication covers the work of the Division of Coal Mine Inspection, Bureau of Mines, as performed under provisions of the Federal Coal Mine Safety Act. It presents background information and data since 1952 when the Act became effective and includes up-to-date statistics for the calendar year 1962. During that year, approximately 9,704 coal mines were active in the United States, and the Bureau made 12,810 regular inspections. BACKGROUND The Federal coal-mine inspection program was established to carry out the provisions in Public Law 49, 77th Congress, (H. R. 2082) approved May 7, 1941. This act has since been amended as Title I, Advisory Powers Relating to Health and Safety Conditions in Mines, under Public Law 552, 82d Congress, approved July 16, 1952, which also included Title II, Prevention of Major Disasters in Mines. Public Law 552 is known as the Federal Coal Mine Safety Act.

Jan 1, 1963

By A. Tewarson

Combustibility data are presented for 14 samples representing commonly used mine materials (treated and untreated wood, conveyor belt and brattice cloth). The combustibility data were obtained in the Factory Mutual Small-Scale Combustibility Apparatus (sample area -0.008 m ). The hazards associated with the mine materials were evaluated in terms of: 1) ignition/ surface flame spread using an ignition parameter (IP). A reasonable correlation was found between IP values and U.S. Bureau of Mines ratings for conveyor belts and brattice cloth and large-scale fire test data for treated and untreated timber sets; 2) generation of combustible vapors, using a vapor generation parameter (VP); 3) heat release using a heat generation parameter (HP). A reasonable correlation was found between HP values and the large-scale fire test data for treated and untreated timber sets; 4) generation of "smoke," toxic and corrosive products using a chemical compound generation parameter (CP); and 5) light obscuration by "smoke" using the light obscuration parameter (LP). All the wood treatments, except Fireguard, were found to be effective in reducing the fire hazard. The effectiveness of the treatment appears to be due to enhancement of carbon formation in the solid phase and enhancement of water formation in the vapor phase. Concepts are presented for establishing 1) the relationship between various parameters (IP, VP, HP, CP, and LP) and basic properties of materials, and 2) the usefulness of the parameters as criteria for the combustibility and fire hazard evaluations of the mine materials.

Jan 1, 1982

By Jeffery M. Listak, Ernest A. Curth

"It took only 9 years from the first appearance of roof shields on the U.S. longwall mining scene to the present predominance of shield faces. An apparent consequence is the welcome downward trend in accidents related to failures in longwall ground control. The report addresses load prediction, the effects of shield geometry on support loads, factors contributing to ground control, and related techniques. The Bureau of Mines took an active part in the evolution of longwall mining, including developing one of the first shield faces in 1975, the first lemniscatetype shields in 1976, the Mine Roof Simulator completed in 1980, the first shields in steeply pitching coalbeds in 1981, and the first multilift working of a thick coalbed in 1982. The information offered in this state-of-the-art report will assist in establishing criteria for roof support selection. INTRODUCTIONIn terms of roof support technology, the introduction of shields in the seventies and eighties was a major step forward. Table 1 indicates the predominance of shield faces on the U.S. longwall mining scene and its apparent consequence, a welcome downward trend of ground-control related accidents.The rapid progress of longwall technology began in 1975 and is highlighted by a development leading from the caliper shield to the modern lemniscate type. Shields have been gaining preference over chocks since their advent to longwall mining in 1975. Safety and productivity factors favoring shields over chocks are--1. A sheltered working space requiring minimum cleanup work.2. Structural stability that allows advancing without delay even with brushing roof contact and, by controlling all lateral loads, removing the requirement for cumbersome leg restraint and restoration devices.3. Wide hydraulic range of mining height.The development of roof shields in the Federal Republic of Germany preceded and paralleled their rapid adoption by U.S. miners. In 1983, 87 pct of the total production in Germany came from shield faces (1).2 In Great Britain, the National Coal Board introduced the first shield support system in 1977 to initiate Advanced Mining Technology (ATM) and Heavy Duty Mechanization (HDM) programs; as of mid-1982, 44 shield faces were operating, or 7.5 pct of a total of 581 faces CJ_)."

Jan 1, 1985

By W. H. Oppelt

The continuous gasification of lignite in an externally heated alloy-steel re-tort was investigated by the Bureau of Mines, Grand Forks, N. Dak., from 1945 to 1951. The main objective of the long-term experimental program was to obtain data on the mechanical performance of this type of gasification retort, particularly the alloy-steel heat-transfer surface of the retort, when operated on large pilot-plant scale. At the same time, extensive experimental data were obtained concerning the effect of process variables and the effect of a limited number of design modifications on gasifier performance. In the period covered by this progress report 4 pilot-plant runs totaling 2,879 hours of operation were completed with the rolled-plate, 310-alloy reaction tube. Over 30 million cubic feet of gas, having H2-CO ratios from 2.1 to 4.4, was made by the partial gasification of 636 tons of 1-1/2-by 3/8-inch natural lignite. Rates of gas generation were from 8,200 to 14,300 cubic feet per hour. Three of the four runs were carried out with the lowered gas offtake or continuous-annulus design modification of the gasification retort. In the final run of the series, gasification of lignite from seven different mines in North Dakota and Saskatchewan, Canada, was investigated at similar combustion-space temperatures and lignite and steam feed rates.

Jan 1, 1955

By R. T. MacMillan

A number of chemical techniques have been applied to manganese ores from three areas of Aroostook County, Maine. Although large tonnages of these ores have been proved, they are low grade, and their exploitation has awaited a suitable beneficiation scheme. As conventional ore-dressing methods had failed to yield satisfactory results, attention was turned to chemical procedures. Leaching with dilute (7-percent) H2S04 extracted over 90 percent of the manganese from ore of the Dudley farm area, consuming 3.8 pounds of acid per pound of manganese extracted. Ores from the Littleton Ridge and Maple Mountain-Hovey Mountain areas were less amenable to this treatment, yielding approximately 80 and 60 percent of their Mn content, respectively. To increase the percentage extraction of manganese in the latter two ores, a number of factors were varied, including (1) acid concentration in the extracting solution, (2) ratio of acid to Mn in the slurry, and (3) preliminary heat treatment of the ore with a reducing agent. Other acids, including HNO3, HC1, and H2SO3, were tried also; however, no significant improvements in the Mn leached from Maple Mountain-Hovey Mountain ore were made. The manganese extraction of Littleton Ridge ore was raised to 90 percent by providing 9 to 11 pounds of HNO3 per pound of Mn in the ore.

Jan 1, 1954

By A. B. Campbell

The Bureau of Mines is developing alloys using ion implantation as an alternative to bulk alloys that consume large quantities of strategic materials such as chromium and nickel. These alloys are formed at the outer layer of relatively common materials. To more fully understand the corrosion characteristics and physical properties of this outer layer, it was necessary to deter-mine the alloy concentration as a function of depth into the substrate material. Also, since many of the ion-implanted alloys would be utilized at elevated temperatures, it was necessary to determine the diffusion behavior of the implanted element. Proton-induced X-ray emission and inert gas ion sputtering have been utilized to generate composition depth profiles for Fe-Cr, Fe-Ni, and Fe-AI ion implanted alloys fabricated by implanting 25-kev Cr+, Ni+, or AI+ into iron substrates. The data were fitted (utilizing a computer program) with symmetrical Gaussian profiles yielding values for the range and range straggle of the ions. These parameters were then compared with those calculated from theory. Changes in the profiles due to annealing were investigated and values for the diffusion coefficient were obtained assuming diffusion according to Fick's Law. For the Cr+ and Ni+ implantation, the profiles as-implanted agree reason-ably well with theory and exhibit ?norrmal" diffusion characteristics at 500° C. For the Al+ implantation, the profile as-implanted is much broader than predicted and exhibits substantial enhanced diffusion at temperatures up to 500° C.

Jan 1, 1979

By K. K. Kelly

METALLURGICAL thermochemistry of titanium is a broad subject and (if data were available) could include a wide variety of topics. The present report is restricted to extractive metallurgy and to substances and reactions that bear upon the magnesium, sodium, and hydrogen-reduction processes employing titanium tetrachloride. The aim has been to present enough data so that the reader not only can check: the calculations for the reactions discussed but also can conduct related calculations if he so desires, without recourse to other compilations of data. The subject matter divides naturally into two parts-the selection of the data to be adopted and the application of these data to pertinent metallurgical reactions.

Jan 1, 1959