Search Documents

By John Paul Gries

This Bureau of Mines study outlines the history of 11 major metal ore deposits or districts that are relatively new discoveries. The oldest operation is the White Pine mine, where major exploration was initiated in 1929. Discovery (delineation of ore bodies) dates range from 1948 to 1976. All but two of the deposits, Quartz Hill in Alaska and Flambeau in Wisconsin, are or shortly will be in major production.

Jan 1, 1979

By James P. May

Operating mine haulage trucks near the crest of stockpiles and waste dumps is a potentially hazardous practice often resulting in a localized slope failure and a dump point accident. The U.S. Bureau of Mines has developed a computer code (INSLOPE3) based on the kinematic method of limit analysis which determines an admissible truck weight (upper bound value) for varying distances from the slope edge. The program considers the material strength parameters, slope geometry, and inertial forces induced by vehicle braking. The program can be utilized to assist in the determination of safe operating distances for a haulage truck from a slope edge, the development of safe vehicle operating procedures, and the admissible weight for a static concentrated loading near the crest of an otherwise stable slope. This report provides information on the use of INSLOPE3, interpretation of the results for mining applications, and instructions for acquiring a copy of the software.

Jan 1, 1991

By M. R. Yenchek

The Bureau of Mines conducted research to determine the relationship between cur-rent load and temperature rises in coal mine trailing cables. Six low-voltage, unshielded, portable power cables were continuously and intermittently loaded with direct current of various magnitudes. Temperature rises within and on the cables were measured with thermocouples, and the data were recorded with a computer. Thermal time constants were calculated, which fixed the periods of the duty-cycle tests. Relationships between average temperature at the conductor-insulation interface and current load were established. The steady-state and intermittent currents that produce a 90° C average conductor-insulation temperature were then determined. Comparisons with Insulated Cable Engineers Association (ICE A) steady-state ratings revealed that 10 to 25 pct more current than recommended ICEA ampacities is required to reach rated insulation temperature. Examination of the maximum intermittent temperatures attained showed that autoignition of coal dust and burn injuries to personnel handling the cable would not be concerns if the temperature at the conductor-insulation interface averaged 90° C.

Jan 1, 1988

By J. Douglas Causey

In 1986 and 1987, at the request of the Bureau of Land Management, the U.S. Bureau of Mines studied 73,010 acres of the 76,480-acre Lower Owyhee Canyon Wilderness Study Area (OR-003-110) in order to evaluate its identified mineral resources. The study area is in Malheur County, OR, about 8 miles north of Rome. There are approximately 7.7 million tons of subeconomic zeolite (heulandite and/or clinoptilolite) resources with ammonia ion exchange capacities as high as 1.75 milliequivalents per gram in the Chalk Basin-Lambert Rocks area. The bed is 25 ft thick with less than 100 feet of overburden. This resource probably will not be mined in the foreseeable future.

Jan 1, 1989

By G. E. Rennick

An oil well penetrating the Pittsburgh bituminous coalbed in northern West Virginia was plugged and safely mined through 3 months later. A sensitive chemical tracer, introduced into the oil reservoir before the test, was not detected in the mine air following the plugging and during mining of the pillar and penetration of the well. Effectiveness of the plugging in preventing reservoir gas from entering the mine through the well hole was verified by continuous monitoring of the mine air for indications of sulfur hexafluoride, an inert gas detectable in amounts as minute as 1/2 part per billion. Expandable cement and fly ash-gel-water slurry were utilized to seal the well above and below the coal seam. Three other wells were also plugged using various techniques.

Jan 1, 1972

"Human accidents are caused by production accidents, generally ones (such as derailment of cars, falling rock, etc.) that have occurred numerous times before an employee was actually involved. Prevention of human accidents is, one of the essentials in cutting operation costs, and advocates of safety are studying economics to assist them in their work of preventing accidents.Workman's compensation insurance or compensation for human accidents is a true operating cost, and is the only purely tangible measure available which gives a measurement of the cost of accidents even though, as will be pointed out later, it represents but a portion of the total cost of human accidents.In using premiums paid for compensation insurance as a measure of the cost of accidents, it must be kept in mind that most insurance laws, as pointed out in a former paper (Serial 2590 of the Bureau of Mines) provide a waiting period before compensation for the lost-time wages starts, with the compensation limited to definite percentages of the wages. The waiting period and limited compensation combined tend to limit the amount paid to an injured workman who, if he receives 1/3 of the lost-time wage, will probably have been reimbursed as high as the average injured workman.The total or complete economic cost of human accidents, must include, in addition to compensation paid for lost time, and the portion of the lost-time wage suffered by the workman for which he is not compensated, the additional cost to the company through-(a) temporary decreased production by the breaking down of the morale, etc., (b) the breaking in of a new employee which is admittedly expensive,(c) the increased liability of human and production accidents caused to or by the new employee.Another charge against accidents, which is not included in the compensation payment, is the economic loss through the killing of as workman who has no dependents. Few of the States' laws require any compensation except burial expenses to be paid for fatalities to persons having no dependents. It is estimated by the United States Bureau of Labor Statistics that the economic loss through a fatality is 6000 shifts. If each fatality was compensated for this amount of time and at half-time wages, using an average wage of $5.00 per shift, the compensation for fatality based on the economic loss would be $15,000. but the average actual compensation paid for each fatality is about $3,000."

Jul 1, 1924

By F. E. Block

The reaction between calcined dolomite and ferrosilicon has been studies with the aim of developing a continuous process for magnesium production. Small-scale tests were made in vacuum retorts similar to those used in the vacuum retort process as developed by Pidgeon (1)2/ and operated during the period of World War II in several Government-owned plants. Factors investigated with respect to the silicon efficiency were the reaction temperature, reaction time, amount of excess dolomite in the charge, and effect of adding sodium silicate to the charge to serve as a binder. Additional laboratory tests were made to study the reaction at elevated temperature but at atmospheric pressure. Silicon efficiencies exceeding 80 percent were found to result when operating in the temperature range from 1,750° to 1,800° C. for periods of 20 to 30 minutes.

Jan 1, 1956

By James R. Coldwell

Mining and processing cost analyses were conducted by the U.S. Bureau of Mines on massive sulfide copper-zinc and low sulfide vein gold deposit types that may be found in the Ketchikan Mining District. Reserves and recoverable metal values (RMV) needed to make these deposits economically viable were modeled. Methods for estimating ore grades and required RMV are presented. Economic modeling for massive sulfide deposits indicated the RMV necessary for a 15% Discounted Cash-Flow Rate-Of-Return (DCFROR) for an underground cut-and-fill mine ranged from $137/mt for a 6,100 mtpd on-site milling operation to $526/mt for a 450 mtpd off-site milling operation. On-site milling was always less costly than off-site milling. Economic modeling for low sulfide vein gold deposits indicated the RMV necessary for a 15% DCFROR for an open-pit mine, off-site mining operation ranged from $S4/mt at 2,900 mtpd to $71/mt at 360 mtpd, and from $49/mt at 2,900 mtpd to $100/mt at 360 mtpd for an on-site milling operation. Off-site milling was less costly than on-site milling until production exceeded approximately 1,700 mtpd. Then, economies of scale reduced operating costs enough to offset the higher capital costs required for on-site milling.

Jan 1, 1995

By Eric R. Bauer

The magnitude and rate of advance of an inmine coal squeeze was deter-mined by measuring roof-to-floor convergence on a regular basis. A dial-gage tube extensometer was used to collect data. Using these measurements) Bureau of Mines employees drew contour maps and graphs to show the direction and rate of squeezing. Information on the rate of squeeze advance was used to determine whether steps should be taken to prevent roof and/or floor movement from closing an entire section of the mine and if alteration of mining plans was necessary to prevent further squeeze development. Data analysis revealed that the squeeze was decelerating; thus there was no need to strengthen support in the areas of the mine that were studied. Mining plans were altered, however, as a result of the findings of this investigation.

Jan 1, 1981

By Townsend. James W.

"INTRODUCTION As a byproduct of its mineral investigation program, the Bureau of Mines has developed a number of operating devices and techniques worthy of note. This paper, prepared under the direct supervision of Paul T. Allsman, chief, Salt Lake City Division, Branch, and under the general supervision of Lowell B. Moon, chief, Mining Branch, reports upon one such device. A simple device has been developed for measuring angles of deviation from the horizontal as recorded on a glass tube by acid etching. The device has facilities, also, for measuring the angle between the long axis of the ellipse and the north-south reference points established by a Maas compass or from an established axial lamina, on the tube, which was ori¬ented to a specific direction in the hole by rod alinement.The device was found accurate within half a degree on repeated orientations of the same tube. However, the degree of accuracy is dependent on the accuracy of personal manipulation in orienting the tube to the correct plane."

May 1, 1947

By Irving Hartmann

Rock-dusting of coal mines is a most important safety measure for preventing or limiting the propagation of explosions. The Bureau of Mines has recommended for many years that rock dust be distributed on the top, ribs, and floor of mine entries and other workings of all bituminous coal and lignite mines in sufficient quantities to maintain the incombustible content of the dust above the minimum requirements. Rock-dust barriers constitute a secondary safeguard used occasionally to complement generalized rock dusting at entrances to panels and side entries or at other locations. In general, rock dust can be applied effectively with modern rock-dusting machines. However, in thin coal beds, in certain back entries, and in some other areas, rock-dusting machines cannot be used conveniently. Furthermore, many small mines find the purchase of machines costly. In such cases, rock dust is not used at all, or else it is distributed by hand, a relatively slow and costly procedure. In recent years some coal mines have started applying rock dust with the aid of permissible explosives. This may be done in various ways. One method consists in placing a stick of explosive on the floor of a room or entry midway between the ribs and covering the stick with two bags of rock dust that are slit on top and set crosswise one above the other. The explosive is then fired, causing the rock dust to be distributed on the nearby roof, rib, and floor surfaces. The procedure is repeated at desired intervals until the entire area is rock dusted. The method is claimed to be rapid, safe, and inexpensive.

Jan 1, 1950

By Forrest T. Moyer

Injury experience in the coal-mining industry was worse in 1965 as both the frequency and severity rates of injuries increased 2 and 6 percent, respectively, over comparable data for 1966 (tables 1-8). The retrogression in the safety record during; 1965 resulted frog the less favorable record at bituminous-coal mines, which more than offset the improved injury experience at anthracite mines. The 259 fatal and 11,138 nonfatal injuries occurred at a rate of 45.77 per million man-hours of exposure and resulted in a severity rate of 8,960 days lost per million man-hours. Although the number of fatalities was the second lowest annual total in the recorded history, it was 17 higher than in 1964. At anthracite operations the total of 6 fatalities in 1965 was the lowest annual figure in statistical history. The annual numbers of nonfatal injuries at ill coal mines and the resulting rates of occurrence have varied little in the past 5 years (table 1). The total days lost from all injuries rose from 2.1.3 million in 19b4 to 2.23 million in 1965 (table 5). Fatal and permanent total injuries, with a standard time charge of 6,000 days each, accounted for 1,650,000 days; Permanent partial injuries, 191,932 clays; and temporary total disabilities, 383,911 days. The severity rate for fatal injuries was 6,241, 8 percent higher than in 1964, and the nonfatal severity rate of 2,718 days lost per million man-hours was 2 percent higher than in the preceding year. The average severity of permanent partial injuries ire; 730, or 48 days fewer per injury than in 1964. The average days lost for each temporary total injury was 36 days in each year.

Jan 1, 1968

With a growing concern over mine fires, prevention and suppression are hot topics. NIOSH researchers Michael Trevits, Alex Smith and Edward Thimons discuss their research in the area. The leading causes of US mine fires include flame cutting and, welding operations, frictional heating and ignitions, electrical shorts, mobile equipment malfunctions and spontaneous combustion. From 1990 through 2007, there were 1601 reportable fires that occurred in the US mining industry -an average of 89 fires per year. The fact that mine fires are occurring with alarming regularity reinforces the importance of recognizing and eliminating the potential hazards. These statistics also show the need for improved control and suppression technology to ensure worker health and safety if a mine fire does occur.

Jan 1, 2008

By Kenneth Maas

The Bureau of Mines devoted portions of the 1987-1988 field seasons to investigate the mineral aggregate industry in Juneau, Skagway, Haines, and Gustavus, Alaska, as part of the Juneau Mining District study. Statistics compiled for current suppliers include location, activity, reserve estimates, expected mine life, and types of commodities available. Each population center, except for Gustavus, is well endowed with suitable mineral aggregate to last at least 20 years. The Bureau of Mines quantified the mineral aggregate resource in many large potential sites within each area. Sampling, engineering and soil-index testing, site descriptions, deposit dimensions, and gold recovery information is described. Refraction seismic studies performed at three localities revealed gravel thicknesses in excess of 40 to 80 feet. In the Juneau area the Herbert/Eagle Rivers outwash area, East Fork Lace River. Antler/Gilkey Rivers, and Grizzly Bar (Taku Inlet) individually contain in excess of 60 million yd3 of excellent-quality aggregate with minor accessory gold credits. Haines is also well endowed with aggregate resources; large, quality deposits occur along and at the confluences of the Chilkat, Katzehin, Klehini, Tsirku, and Kicking Horse Rivers. Large deposits of granitic aggregate exist in the Skagway River and East Fork Skagway River.

Jan 1, 2012

By Richard L. Unger

The Bureau of Mines entered into a cooperative agreement with an eastern Kentucky coal mining company to comprehensively redesign the flow of equipment and supplies throughout its underground mines. Items were tracked from delivery to the warehouse and from surface storage areas to their final usage locations underground. Three underground mines were visited, and a great variety of tasks were videotaped for subsequent laboratory analysis. Of particular interest were tasks that required manual handling of the supplies or equipment components. Activities such as handling daily supplies (concrete blocks, rock dust, and cross- beams) and handling or lifting the continuous miner power cable were determined to be the most hazardous. Recommendations to the company included redesigned surface storage areas to facilitate the use of forklift vehicles to load the underground supply cars. Designs were also developed for different mechanical- assist devices to help in unloading the supply cars underground and to handle equipment maintenance tasks underground. Additionally, the videotapes of the underground manual handling tasks became the basis for simulating those activities in controlled laboratory conditions. This testing will contribute to developing guidelines for proper lifting techniques for low-seam coal mines.

Jan 1, 1986

By Oliver Bowles

"Conservation of slateWaste slate is a problem of outstanding importance in the slate industry, for a very large proportion of all slate quarried is thrown on the waste heap. While many uses for waste slate have been found, the demand calls for merely a fraction of the present supply of unused material. If the slate industry is to increase in prosperity, the producer's energy must be directed toward the development of ways and means of reducing waste to the lowest possible point. The Bureau of Mines of the Department of the Interior has devoted much study to this problem and a recent bulletin ** contains a detailed discussion of the waste problem.Attention has recently been directed toward an improved method of cutting slate in quarries, a method that promises to reduce greatly the percentage of waste material. The method has been introduced since that bulletin was published, and this supplementary paper covers the details of the process.A reversion in method,In connection with this new mode of operation history is repeating itself in a very interesting way, for the old quarry bar used years ago with steam drills, and later discarded in favor of the channeling machine .and the hammer drill, has been salvaged from the scrap heap, and again put to active use. The occasion for its employment is an attempt to improve quarry methods by the substitution of drilling for channeling or blasting."

Oct 1, 1923

By F. N. Bender

Percolation leaching of wad-type manganese ores was investigated, using a novel system of alternate upward passage of sulfur dioxide gas through moistened ore and downward percolation of wash solutions to extract solubilized manganese. Bench and large-scale tests designed to simulate vat and heap leaching were made on four wad ores from Arizona and Nevada and on a pailomelane ore from Arizona. Three of the wad ores required prebaking at 500° to 600° C. to produce a permeable agglomerate that would not slake during percolation washing. The hard-type ore and one of the wad ores that contained a large amount of granular gangue did not require prior roasting. The deportment of the different ores toward leaching and percolation was studied with particular reference to the influence of the sulfur dioxide - oxygen ratio and the effect of gas dilution on the rate of manganese dissolution, dithionate formation, and acid production. Crushed charges of the ores, as coarse as 1 inch and as fine as 1/4 inch, were treated for periods of 5 to 11 days. Percolation of the gas and leach solutions through the charges was achieved without difficulty. The manganese extractions varied between 78 and 97 percent and depended upon the size and type of ore leached. The average quantity of sulfur dioxide required in the larger scale tests was about 2.6 pounds per pound of manganese recovered. The dithionate formation varied from 0.35 to 0.9 pound per pound of manganese extracted depending upon the strength of leaching gas.

Jan 1, 1957

By C. H. Elder

Coal degasification boreholes drilled from the surface have been success-fully hydraulically stimulated to increase the flow of gas from the coal. This Bureau of Mines report describes the hydraulic stimulation procedure for a coalbed, the equipment required, and design criteria for the treatment. Three examples of stimulation treatment show from fivefold to twentyfold increases in gas production. The tests were conducted in the Pocahontas No. 3 coalbed, Buchanan County, Va., the Pittsburgh coalbed, Washington County, Pa., and the Mary Lee coalbed, Jefferson County, Ala. Two sites where the coal was hydraulically stimulated and exposed by subsequent mining show no adverse effect on mining operations through the treated zones. The induced vertical partings were confined to the coalbed and did not in any way affect either roof or floor rock.

Jan 1, 1975

By R. Pakalnis, Richard P. Curtin, Lewis A. Martin

Instrumented cable bolts developed at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health were used in conjunction with existing ground control to monitor rock mass loads at various field sites (FMC Granger, Getchell, Meikle, SSX, K-2, and Stillwater). Axial and shear loads were determined by strain gauges to levels of instrument accuracy of ±5 N or ±5 microstrain as these loads were transferred to the instrumented cable bolts. These gauges were 12.5 mm long and embedded into are manufactured king wire that replaced the conventional king wire. Cable bolt performance, quality of grout, and installation techniques were also assessed. By using instrumented cables, a mine operator can determine axial load along the cable at predefined gauge locations. By monitoring load on and displacement of the rock mass, more effective ground support can be selected and installed, which will lead to safer working conditions for miners.

By Robert L. Lagace

A prototype adaptive volume control for the loudspeaker output of mine trolley carrier phones was designed, built, and tested in the laboratory and in a mine. This volume control senses, and adapts to, the ambient acoustic noise environment in such a way as to produce a loud sound output under noisy conditions, and a quieter output under quiet conditions, thereby producing an understandable and unstartling volume level under all noise conditions. The design approach, prototype hardware, and test results are described, and the device is shown to be feasible for in-mine operations. The circuit design principles are easily applicable to currently available mina trolley carrier phones. Recommendations for practical improvements are included. An in-mine experiment to assess the practical feasibility and utility of the dedicated wire technique for overcoming poor trolley carrier phone system performance was designed, performed, and evaluated. The technique involves the use of a single, low-loss, properly terminated auxiliary wire, placed in the rail haulageway, which allows signals to naturally couple to and from the trolley wire/rail transmission line, and thereby significantly decrease the overall signal attenuation rate on the trolley wire/rail line. The in-mine dedicated wire experiment, results, and conclusions are described, and the technique is shown to be a valid and practical one for significantly Improving carrier phone system performance in mines. Guidelines for the installation and use of the dedicated wire are provided. Recommendations are made for obtaining further practical information on its performance and utility. A second in-mine experiment to assess the feasibility and utility of the low-impedance (low-Z) line technique for overcoming poor carrier phone signal transmission in mines was designed, performed and evaluated. The low-Z line technique involves the periodic connection of shunt capacitors between the trolley wire and the rail to artificially lower the line characteristic impedance. This causes the low impedance shunt loads encountered across the trolley wire/rail line to be less mismatched to the line, thereby reducing the overall attenuation of carrier phone signals. The results of in-mine experiments performed along unenergized and fully operational sections of trolley wire/rail line are described. The experiments were designed to measure line parameter such as inductance and capacitance per unit length, characteristic impedance, and propagation phase velocity, in addition to signal strength versus distance behavior under normal and low-Z line conditions. The low-Z line technique is shown to be valid, but not as practical as the dedicated wire technique which is recommended as the most favorable for most coal mine applications.

Jan 1, 1979