Search Documents

By Keith A. Heasley, John L. Ellenberger, Paul W. Jeran

In this paper, a state-of-the-art, three-dimensional, full waveform, microseismic system was used to analyze the rock failure around a deep (> 750 m (2500 ft) of cover) bump-prone longwall panel. The microseismic system consisted of both underground and surface geophones coupled through radio telemetry and a fiber-optic network to produce pseudo real-time detection and location of seismic events surrounding the coal seam. This was the first microseismic installation of this scope at a U.S. coal mine, and the system was intended to help determine the exact strata mechanics associated with the redistribution of stress and the associated gob formation at one of the U.S.’s deepest longwall mines. Overall, 5,000 calibrated seismic events were recorded during the mining of one panel, including a Richter magnitude 4.2 event which occurred inside of the array. Analysis of these events provides a number of notable insights into the rock mass behavior. For instance, the longwall panel was widened during the retreat process, and the mining-induced seismicity shows a distinctly different behavior between the start of the panel, the mining of the narrow part of the panel and the mining of the wider part of the panel. Also, in itself, the acquisition of the ML 4.2 event was a major milestone in geomechanical and bump research. This is the first time that such an event has been recorded with this detail and accuracy at a bump-prone coal mine in the U.S. The analysis of this single event has set distinct new limits on the relationship between mining seismicity and coal bumps.

By C. S. Compton, D. R. Dolinar, D. C. Oyler

More than 80% of U.S. roof bolts are fully-grouted, but about 1500 roof falls are reported each year. Anchorage failure of a fully grouted bolt can occur when the roof is active near the top of the hole. This paper reports on an extensive series of short-encapsulation pull tests (in which the bolts are installed with only 1 ft of resin) that were conducted in the National Institute for Occupational Safety and Health (NIOSH) Mine Safety Research Laboratory and operating mines in WV and PA. The tests confirmed that poor anchorage can been countered under some weak rock conditions. Suggestions for improving anchorage are included.

By Ch. D. Taylor

Past studies with blowing face ventilation systems have shown that using a machine-mounted scrubber and water sprays can reduced methane levels at the face. The current research was conducted to determine how the sprays and scrubber interact to reduce methane levels, and what spray configurations provide the best face ventilation when used with a scrubber. Testing was conducted in a ventilation test gallery designed to simulate a full-scale mine entry. In the entry, a model mining machine, equipped with a simulated dust scrubber and water spray systems, was located at the face of a 6.1 m (20 ft) box cut. Face ventilation was provided by a blowing curtain located 12.2 m (40 ft) from the face. Methane released from a manifold at the face was measured at six locations near the face to compare the ventilation effectiveness of the spray systems while operating with and without the scrubber. Airflow movement across the face was affected by the spray configuration and scrubber operation. Average face concentrations were lowest when directed sprays were used with the scrubber. Varying the direction of the scrubber exhaust affected face methane levels.

By R. S. Dean

"INTRODUCTION The metallurgical research program of the Bureau of Mines has been somewhat disorganized, but generally advanced by the increased activities of the war period. The present report is for the purpose of summarizing the work of the Bureau in this field for the past 15 years and indicating its future plan.Fifteen years ago the Bureau turned from its pioneer work on the physical chemistry of steelmaking to an emphasis on raking a pure steel synthetically, rather than by refining, that is, :producing each of the steel 'constituents in the pure state and combining them by simple melting. Such a procedure permits the use of less high-grade ores, not only of iron, but of the ferroalloy metals, such as manganese and chromium,This program has led to extensive work on iron-ore concentration, agglomeration, reducibility of ores and agglomerates, direct reduction of iron ores and concentrates by a wide variety of processes; special refining processes for iron, the production of pure mangenese, chromium, and cobalt from low-grade ores by electrolytic processes, the production of ferrochromium, ferronickel, and ferronickel-cobalt from low-grade domestic ores, and the development of many special alloys to effectively use the new products.The status of the work in each of these fields and the future program of work, together with a bibliography of papers and patents by the Bureau staff on each of these subjects, are given."

Jul 1, 1946

By Avery H. Reed

RECORD production of cement, clays, salt, sand and gravel, and stone highlighted the mineral industry of the State in 1956. Coal and iron-ore production declined owing to increased imports of foreign iron ore and decreased demand for metallurgical coke. Alabama ranked second in production of bauxite and of native asphalt, and third in output of iron ore. New developments in the State included the Citronelle oilfield and its 97 wells, which more than doubled the total production of petroleum compared with 1955. There is no question about the impetus that field has given to the oil and gas industry in Alabama, now 13 years old. The State's 4 oilfields are in southwest Alabama and its 1 gasfield is in Marion County, in the Warrior coal basin.

Jan 1, 1958

By Forrest T. Moyer

THIS CHAPTER of the Minerals Yearbook contains injury experience and related employment information for the coal-mining, coking, oil and gas, peat, and native asphalt industries in the United States for 1963. No attempt has been made to combine these data and present injury-frequency rates reflecting the mineral-fuel industries because the hazards of the separate industries are not comparable. Tabulations showing the trend of injuries and employment for all mineral industries are presented in Volume III of the Minerals Yearbook. COAL Injury experience of the coal-mining industry was improved slightly in 1963, as measured by the 2-percent decline in the Injury-frequency rate. Although the total number of fatal and nonfatal injuries increased 1 percent, the greater proportional increase of 3 percent in man-hours worked accounted for the improved frequency rate. Employment and injury data for 1963 are based on final data for anthracite mines and preliminary data for bituminous coal and lignite mines.

Jan 1, 1964

To provide operators of large-opening mines with a ventilation planning tool that will help them develop a healthier, safer, and more efficient ventilation system in the underground workplace.

Jan 3, 2006

By Arthur H. Redfield

The expansion of city street laving which characterized the ten years ended December 31, 1929, according to a survey of 201 representative cities, made by the bureau of Mines, reached it climax in 1927, with decreases reported for 1928 and 1929. The upward trend, followed by a decline, was general in cities of all sizes included in this study, but was most pronounced in cities of 40,000 to 100,600 inhabitant and in the Northeastern, Southeastern, and Southwestern States. In the North-Central States the trend of paving; was downward from 1925 to 1929; in the Pacific, and Rocky Mountain States it was generally upward. Over the nation as a whole, bituminous types of paving continued to lead, furnishing two-thirds of the total street pavement laid in the 201 cities from 1925 to 1929. The actual yardage of bituminous pavement laid in these cities, however, was 3.8 per cent less in 1923-than in 1925, and the ratio of bituminous pavement to the total pavement t dropped from 70.4 per cent in 1925 to 62.1 per cent in 1928, rising to 65.1 per cent in 1929. The area paved with Portland-cement concrete amounted to only one-fourth of the total, pavement laid in these cities from 1925. to 1923., but the yardage of Portland-cement pavement increased by half during the period, and its share in the total pavement grew from 19.3 per cent in 1925 to 30.0 per cent in 1928, declining to 29.5 per cent in 1929. Brick, block, and stone pavements, which constituted the remaining one-twelfth of the total pavement laid in the 201 cities, decreased one-third in yardage, and declined in relative importance from 10.3 per cent in 1925 to 6.6 per cent in 1929.

Jan 1, 1931

By David Hill

The Australian underground coal mining industry has made extensive use of the Coal Mine Roof Rating (CMRR) classification system for a diverse range of purposes in recent years. These include mining method selection, and coal pillar and roof support design. This paper outlines a series of case histories, from large-scale feasibility studies to local support design investigations, that collectively illustrate the broad applicability, advantages, and usefulness of the methodology, as well as some of the current limitations. The key role of the CMRR in an overall hazard definition methodology is demonstrated for a major Australian project, and some ideas with regard to the future application of the CMRR, in the context of geotechnical risk management within a progressive, highly productive extractive industry, are put forward.

Jan 5, 2007

By Forest J. Sur

"INTRODUCTION This report describes an exploratory project conducted by the Bureaus of Mines on a fluorite deposit, near Glenwood, N. Mex. Results of wagon drilling, crosscutting, and test pitting are given, together with results of metallurgical tests made upon samples of the ore. Mining and treatment methods are suggested.C. H. Johnson, Bureau of Mines engineer, examined the deposit in August 1942. H. E. Rothrock, of the Federal Geological Survey, completed a preliminary geologic study and mapped the deposit during the fall of 1942. As a result of these brief investigations, it was concluded that the deposit contained substantial inferred ore reserves, and exploratory work was recommended. G. A. ApelI, also of the Bureau of Mines, made a topographic and underground survey and report on the mine in March and April 1944. A wagon drill, air compressor, and other equipment and supplies were delivered to the property on May 19 to 23, 1944. Drilling began under the direction of the author on May 25, 1944, and was completed in October 1944. The results of drilling and. sampling form the basis of this report."

Apr 1, 1947

By W. R. Reed, G. J. Joy

The personal dust monitor (PDM) is a new coal mine respirable dust sampling instrument that has the ability to provide accurate end-of-shift and real-time respirable dust exposure data. A hypothetical cost comparison analysis of the PDM with the current MSHA-required coal mine dust personal sampling unit (CMDPSU) was conducted. Some simplifying assumptions were made to create hypothetical cases for analysis. This analysis was limited to respirable dust sampling of one designated operator (DO) and one designated area (DA) for one mechanized mining unit (MMU) which operated one shift per day. Only sampling intervals of the minimum sampling as required by federal regulations and continuous sampling were analyzed. This cost analysis from the company perspective is only one part of an overall cost/benefit analysis that should be conducted at a later date. In this analysis, company-associated costs were examined for both sampling systems. Results show that the PDM, while it has high initial costs of approximately $12,600, may be a cost-effective sampling system for measuring coal mine respirable dust. The estimated present worth cost of conducting the minimum required dust sampling over a five-year life ranges from $5,850 to $19,000 for the CMDPSU, with the higher present worth cost including costs of potential violations incurred. For the PDM, the comparable present worth cost is $14,900 to $19,300, with the lower present worth cost representing a lower capital cost of $8,150 per unit if more than 850 units are produced per year, while the higher present worth cost reflects the result with the higher $12,600 capital cost.

By Douglas Milne

Most empirical and numerical approaches to design in rock mechanics incorporate rock mass classification. Numerical design methods generally use classification values to calculate input parameters for stress-based failure criteria. Empirical methods use classification to allow comparisons between similar rock mass conditions, generally based on a graphical design technique that differentiates stable and failed opening geometries. Classification systems are the best tool available for assessing rock mass properties; however, there are problems with classification systems that should be high-lighted. Rock mass performance can only be realistically estimated by coupling a unique description of the rock mass with known loading conditions. Current classification systems cannot provide a unique classification value. The weightings applied to quantify rock mass properties for classification can result in significantly different rock masses having the same classification values. These weightings have been proven effective for tunnel design and support, but classification systems are now used for many more applications. Rock classification systems evolved from a quick and easy field tool for estimating tunnel stability and support requirements. The need for a rapid field tool means that rock mass classification is relatively insensitive to improved methods of measuring rock mass properties. Problems with classification systems and their application are highlighted in this paper. These problems must be recognized and documented before improvements can be made. An understanding of the evolution of classification systems and their application for both numerical and empirical design approaches is invaluable in highlighting current shortcomings.

Jan 5, 2007

By W. R. K. Wu

Results of linear correlations of two to four variables by the least-squares method are presented. The variables include 63 parameters representing coal composition, coal plasticity, and coke strength. The composition parameters are on chemical analyses; the plasticity parameters, on three plastometer and dilatometer tests and four miscellaneous tests; and the coke-strength parameters, on three ASTM indices. Seventy-two to eighty-four plastic coals were used in the plasticity and carbonization tests, which together form the basis of this report; 43 nonplastic or weakly plastic coals were used in the coal-band studies. Plots of relations between volatile matter, carbon, and oxygen contents of 1,860 U.S. coals and the 84 coals used are shown. Similar plots between volatile matter and hydrogen or atomic H/C of the 84 coals are also included. Significances of regression coefficient signs for coal composition parameters in the significant correlations found are discussed. Based on these significances, the following relations are shown: (a) coke strength versus average aromaticity, or mineral matter content, of the parent coal; (b) characteristic temperatures of the plastometer and dilatometers, the free-swelling index, or the Gray-King type versus average hydroaromaticity of the coal; and (c) nontemperature parameters of the plastometer and dilatometers versus the physical properties of a certain group of compounds from thermal decomposition of coal. Similarly, significances between the positions of coals in the coal band and the aforementioned relations are also discussed. A structural theory of coal plasticity is proposed. Applications of the correlation results are discussed. Composition parameters, such as carbon, atomic H/C, and calorific value may be used as a basis for selecting coking coals for stronger coke. Plasticity parameters, such as the end temperatures of the plastometer and dilatometers and the free-swelling index, may be used for the same purpose. Based on the best correlations found, coke-strength indices may be estimated to within 4 to 8 units of the observed values; the end temperatures of the plastometer and dilatometer tests, 5° to 10° C.; and the free-swelling index, within 1 unit. Accuracies of all these estimated values are examined, based on the experimental errors of the data involved. Finally, estimations of plasticity parameters from one test with those from others are shown.

Jan 1, 1971

By Fred N. Kissell, Andrew B. Cecala

In This Chapter [Where methane is emitted at longwall faces Where methane accumulates at longwall faces Using the modified shearer-clearer to eliminate ventilation eddy zones Using a walkway curtain to reduce methane buildup during the headgate cutout Control of frictional ignitions and The best location for the methane monitor] The methane released along a longwall face represents only 10%–20% of the total methane emitted from the entire longwall panel. Nevertheless, in very gassy coal seams, this methane released at the face can pose a problem because the shearer is a ready ignition source. Preventing methane ignitions at longwall faces requires four actions. The first is to provide better ventilation around the shearer to eliminate the ventilation eddy zones at the drums where methane builds up. These eddy zones are eliminated by mounting additional water sprays on the shearer to direct air into them. The second action to prevent methane ignitions is to install a water spray behind each cutter bit and regularly replace worn bits. Water sprays behind each cutter bit act to quench the hot metal streak that follows a worn bit when it strikes rock. The third is to ensure that no ventilation eddy zones are inadvertently created by poor placement of water sprays. The fourth is to ensure that the methane monitor on the shearer is in the best location to detect methane accumulations. ADDRESSING METHANE ACCUMULATIONS AT LONGWALL FACES3 Cecala et al. [1985a, 1989] and Denk and Wirth [1991] studied methane emission and ventilation patterns at longwall faces to find where methane accumulations are most likely. Although not always the case, the major source of methane at longwall faces is usually the breakage of coal by the shearer. Stress-related fracturing of the coal seam at the face, called bumps or bounces, can cause the release of additional gas (Figure 4–1).

Jan 6, 2006

By Allen S. Smith

Analysis of the helium content of a natural gas presents more than the usual difficulties encountered in applying the thermal--conductivity method because of the relatively small amounts of this inert gas present and the wide variation in the other constituents. However, the numerous advantages of this method and its adaptability to continuously recording and control instruments make it worthy of consideration. A specific application of the method described yields quantitative results only when used with gas mixtures of known qualitative compositions which vary within predetermined limits. Periodic analyses for the helium content of a producing gas well may be conveniently made by an absorption method3/ and a continuous analytical method is not necessary for this purpose. Natural gas containing 1.75 to 1.90 percent of helium produced from Government-owned wells is processed in the Amarillo (Texas) Helium Plant of the Bureau of Mines. The helium extracted in the plant is supplied to the Army and Navy, and the processed natural gas is sold to a commercial gas company4/. As complete recovery of the helium in the raw material is not economically practicable, the processed gas contains 0.1 to 0.3 percent of helium, depending upon conditions of operation;- Production is checked against the helium removed from the gas, which before the installation of the thermal--conductivity apparatus was calculated from the analysis of a cumulative sample of the processed gas. As conditions of operation affect the residual helium content to a large extent, a composite sample was an uncertain index of the efficiency of the process.

Jan 1, 1934

By J. Chilton

The fact that methane ignitions continue to occur at the mining face indicates that monitoring with machine-mounted methanometers does not always indicate the presence of high methane concentrations. Methane concentrations at the face change quickly due to changes in airflow. By measuring these changes in airflow, it may be possible to predict changes in face methane levels more quickly. Currently there are no techniques or instruments to accurately measure airflow in by the mouth of the ventilation curtain or tubing. Tests conducted in the NIOSH ventilation test gallery compare the data provided by one-, two-, and three-axis ultrasonic anemometers. The effects of changes in airflow direction and turbulence on instrument readings are discussed, and guidelines are given for selecting the type of instruments to be used for monitoring airflow near the mining face.

By R. Karl Zipf, Kousick Biswas

The main objective of occupational health and safety research is to minimize or eliminate the events that may cause fatal or non-fatal injuries to human workers. A commonly used technique is to devise an “incident prevention plan”, which is more often the product of thorough investigations of past reported incident events. Incident documentation and methodical reporting and systematic and thorough data collection, often help identify the root cause of the incident – in other words, the etiology of the incident. These retrospective analyses of the incidents can efficiently identify the future steps to take to achieve the objective of minimizing occurrence of “events of interest”. This paper introduces a novel technique – “Taxonomic Analysis”, which identifies the root causes of an event (an incident in this case) and can provide future direction for corrective measures to reduce the probability of occurrence of the event. A taxonomic analysis involves systematic and organization of data based on observation, description, and classification. This paper utilizes the rock fall related incident narratives, available with the Mine Safety and Health Administration (MSHA) database (1984-1999), for a taxonomic analysis. The study found that 67.6% of groundfall incidents occurred in supported areas with the remainder (32.4%) in unsupported areas. Some form of rock mass failure appears to cause about 50% of groundfall incidents, although in 39.7% of the overall groundfall incidents or two-thirds of those involving rock mass failure, the exact nature of the rock mass failure could not be determined from the narratives. Human activities factors such as scaling or barring down, drilling or bolting, and setting timbers or cribbing accounted for another 34.5% of the groundfall incidents. Finally, support system failures made up the remaining 15.5%. Results from this taxonomic analysis may suggest focus areas toward which preventive measures and future research activities could concentrate.

By Charles E. McCarthy, MORTON T. PAWEL, E. A. GEE, FRANK S. RIORDAN

Large tonnages of the magnesium silicate mineral , olivine, are known to exist in the mountains of western North Carolina and in the Puget Sound region of Washington. The North Carolina deposits alone are reputed to contain at least 230 million tons of ore averaging 45 to 49 percent of magnesium oxide In both areas the mineral is readily accessible and can be mined by the simplest methods ; one of the largest of the Washington deposits is located at tidewater .

Sep 1, 1946

By C. M. McKinney

This report contains Bureau of Mines routine analyses of 492 samples of crude petroleum from 470 United States oilfields, each of which produced 2,500 barrels a day or more during at least 1 of the years 1946-56. The fields are listed alphabetically by State and field names in table 1, with information on the geographical and geological sources of the samples. Table 2 summarizes the general characteristics of the crude oils and analytical and computed data determined from the analyses. A previous report 4 contains similar analyses of 283 important United States oilfields; some of them are repeated in this report. Many fields for which analyses previously were published are represented by new analyses, which include data not previously reported. Refractive index nu and specific dispersion, ng minus nD divided by the density, for some of the distillate fractions are included in the analyses of 316 of the crude-oil samples. This is the first Bureau of Mines report on analysis of crude oils to contain such data, and their use in calculating hydrocarbon-type composition of the fractions is explained.

Jan 1, 1957

This appendix contains the list of equipment, their corresponding number and their specifications with the quotations from the vendors/ manufacturers who can supply this equipment. The listings are arranged by process plant areas.

Jan 1, 1979