Search Documents

By D. Harrington

Hatch (260) made the following pertinent statement regarding the present status of engineering design of dust-control equipment: Textbooks on ventilation and engineering handbooks devote little or no space to methods of control of industrial dust, and in the technical journals papers on fundamental engineering design of equipment are conspicuous by their absence. In a recent bibliography of the literature on pneumoconiosis less than 1 percent of the articles dealt with the engineering control of the disease. The science of dust control has not developed beyond the stage of trial and error, and the design of structures for the suppression of dust is based almost entirely upon empirical data together with one or two elementary formulas. The latter were derived from the generalized experience in a limited number of Industries such as woodworking, where conditions and requirements are not at all like those, for example, in a sand-pulverizing plant. Wide experience and good judgment are essential to the proper use of the scanty information that has been collected and systematized. Without attempting to minimize the importance of experience in engineering design, it is necessary to point out that most of the past experience obtained in the empirical design of dust-control equipment was not evaluated by means of quantitative studies of the actual reduction in dust , fence, past experience does not necessarily furnish the proper guide for future design. In fact, recent surveys in certain industries, employing modern methods of investigation, have shown that existing equipment is in many cases inadequate.

Jan 1, 1935

By Robert T. MacMillan

An essentially chemical technique has been developed on a small scale for the efficient utilization of certain domestic titaniferous iron ores. Three main steps are involved: (1) Sintering the ore at 1,050° C. with carbon and soda ash to reduce the iron to metal powder, retaining the titania in the slag, (2) separating the powdered iron from the slag, after wet grinding, by magnetic or gravity methods, and (3) sulfuric-acid decomposition of the titania fraction to produce pigment and certain byproducts. The technique was first applied to the tailings from the Bureau of Mines bauxite-concentrating plant at Bauxite, Ark. A good grade of powdered iron was produced from this material. Subsequently, the work was diverted to the study of the titaniferous magnetite from the MacIntyre Mine at Tahawus, N.Y., because of the potentially higher recoveries of iron, titanium and vanadium. Ninety percent of the iron in this ore has been recovered as an iron powder analyzing 90 percent metallic iron and containing 2 to 3 percent TiO2. The remaining titania was found in the slag and was recovered as pigment-grade TiO2 by application of a suitable technique. The vanadium was distributed between the TiO2 fraction and the alkaline liquor resulting from the wet-grinding and magnetic-separation operations, with only a minor proportion retained by the metallic iron.

Jan 1, 1950

By R. S. Dean

The work of the metallurgical fundamentals section during the past year, representing active experimental investigation or thermodynamic study, may be summarized as the following problem subjects: 1. Low-temperature specific-heat investigations. 2. Development of a method of concentrating gases. 3. Thermodynamic properties of metallic carbides and nitrides, 4. Production of pure chromium from chromium chlorides. 5. Thermodynamic properties of the hydrates of calcium, sulphate. While this list is not identical, with officially designated problems, due to overlapping of subjects and to new developments within specified problems, presentation upon the basis of this subdivision will best serve to review the work of the section.

Jan 1, 1937

By Earl T. Hayes

[This work represent a continuation of the efforts of the Metallurgical Division of the Bureau of Mines to ascertain and apply knowledge of miner physics to processes metallurgy.]

Jan 1, 1941

By Albert L. Toenges

The production of coal from underground mines in Washington declined during the recent war owing to shortage of manpower, and coal was shipped to the Pacific Northwest from mines in the Rocky Mountain region. The movement of this coal into Washington required the use of railroad equipment that otherwise could have been used for transporting war materiel and personnel. Strip mining uses a minimum of manpower, and the development of coal areas in the Pacific Northwest that can be mined by the strip method should increase production in the area, thus releasing railroad equipment from the necessity of transporting coal long distances and also providing consumers with a lower-cost product. The development of a strip mine to supply the demand at low cost requires a large investment in heavy equipment. In order that the fixed charges due to large investment in plant and equipment may be kept at a minimum, large reserves of coal must be proved. A reconnaissance of an area near Toledo, Lewis County, Wash., indicated a large bed of lignite that could be mined by strip methods. The area is approximately midway between Portland, Oreg., and Tacoma, Wash. (refer to fig. 1), and the opening of a large mine in the area would supply fuel to these and other nearby centers.

Jan 1, 1947

By G. B. Gait

This report is the third in a series concerning the Bureau of Mines program for microfilming maps of abandoned mines in the Pennsylvania anthracite region; a catalog of the microfilmed maps of mines in the Lackawanna Basin of tile Northern anthracite field is presented. Previous reports IC 8274, published in 1965, and IC 8379, published in 1968, were catalogs of microfilmed maps of mines in the Eastern Middle anthracite field and Wyoming Basin, Northern anthracite field, respectively , Additional catalogs will be published as the microfilming of significant mining areas is completed.

Jan 1, 1970

By Earl T. Hayes

[This work represents a continuation of the efforts of the Metallurgical Division of the Bureau of Mines to ascertain and apply knowledge of mineral physics to process metallurgy.]

Jan 1, 1941

By E. Don Dilling, Wm. F. Hergert, J. W. Pennington, C. E. Wood, M. J. Slendlove, H. A. Doerner

"INTRODUCTION The Bureau of Mines began a study of various methods for producing magnesium metal from magnesite ores in 1936 at Pullman, Wash., with the cooperation of Washington State College. This work included a study of the basic principles involved in the reduction of magnesium oxide by carbon, which soon led to the development of a continuous process. In May 1939, a small pilot plant was operated, which included a small single-phase arc furnace with a hydraulic feed mechanism and an oil-spray device for shock cooling the metal vapor. 5/Subsequently, the Ford Motor. Co., Dearborn, Michigan, began a study of this process on a larger scale. A pilot plant with a nominal capacity of 10 pounds of magnesium metal per hour was constructed and operated intermittently. A larger unit with a nominal capacity of 100 pounds of magnesium per hour was partly constructed when war activities prevented experimental work.In the meantime, the process was greatly improved through continued investigation by the Bureau of Mines at Pullman, and these improvements were successfully tested by continuous operation in a small pilot plant having a normal capacity of 4 pounds an hour."

Aug 1, 1945

The following is a Maintainability Design Checklist for coal mining equipment. The purpose of the checklist is to provide a summary of design review points for the maintainability assessment of new or existing underground equipment. It specifically focuses on the identification of equipment design features, tasks, or procedures that impact equipment downtime, repair costs, labor hours and maintainer skill level requirements. Some checklist points are general in nature. The checklist was designed to be used across all categories of underground equipment. The intent is to draw attention to design features and maintenance procedures that will increase maintainability requirements. You are encouraged to adapt this checklist to site specific or machine specific requirements by: ? Inserting specific performance criteria for various categories of maintenance tasks. For example; all hydraulic lines on a shuttle car should be replaceable in 15 minutes or 25 minutes, etc. ? Adding or deleting checklist items for different categories of equipment. You would include environmental control equipment, for example, on face equipment and not on shuttle cars or man trips. ? Adding additional checklist items based on site or equipment specific maintenance histories or experience, company maintenance standards, or other factors.

Jan 1, 2000

1. Domestic Production and Use: In 1982, 13 companies operated 30 primary aluminum reduction plants, with 3 firms accounting for 55% of production. Washington, Oregon, and Montana accounted for 34% of the production; Texas, Louisiana, Missouri, and Arkansas 18%; Tennessee, Alabama, South Carolina, and North Carolina 14%; other central and eastern States 34%. Based on published producer prices, output of primary metal in 1982 was valued at over $5.5 billion. Aluminum consumption by 25,000 firms was centered in the East Central United States. Packaging accounted for an estimated 39% of domestic consumption in 1982, transportation 20%, building 14%, electrical 8%, consumer durables 8%, and other uses 11%.

Jan 1, 1983

By Harold L. Rhodes

The Bureau of Mines has developed a method for determining the H2S content in natural gas samples. A gas chromatograph with a flame photometric detector was used to analyze samples with H2S concentrations ranging from 5,000 ppm to a minimum detectable limit of 0.01 ppm. A mass spectrometer was used to analyze samples containing H2S in amounts greater than 5,000 ppm. Methods are presented for preparing containers for H2S samples and for preparing standards using partial pressure and weighed standard methods, Sample collection techniques are discussed, as are analytical results which illustrate the loss of H2S while in the sample container and provide a basis for evaluating containers used for sampling and standard preparation.

Jan 1, 1979

By D. K. Denton, J. M. Girard, D. F. Scott, T. J. Williams

Personnel from the Spokane Research Laboratory, National Institute for Occupational Safety and Health, examined an underground pillar at the Homestake Mine, Lead, SD. Investigations involved strain relief and seismic tomography studies in the mine, and ultrasonic velocity measurements on pillar core in the laboratory. Measured octahedral normal stress was 37 MPa (5,366 psi); seismic P-wave velocities averaged 5.2 km/s (17,060 ft/s); and ultrasonic velocities at a pressure of 39.6 MPa (5,750 psi) averaged 6.3 km/s (20,669 ft/s). The difference between in-mine and laboratory velocities is attributed to the attenuation of seismic energy by mine fractures larger and more numerous than those in the samples of core measured in the laboratory. Using these results, researchers hypothesize that pillar rocks have the ability to withstand stress an order of magnitude greater than they currently sustain.

By R. R. Wells

This report summarizes the results of preliminary mineral-dressing studies by the Bureau of Mines on five samples of copper-bearing ore from various Alaska de-posits. The work on each sample was not extensive enough to warrant individual publication. The results, however, indicate the possibilities and limitations of concentration of the respective ores. The information therefore may be helpful in future development of these ore bodies. Four of the five samples tested were submitted to the laboratory by engineers of the Bureau of Mines as part of the examinations and survey investigations of strategic-mineral deposits in Alaska. This program is conducted to assist development of mineral resources in the Territory and particularly to aid economic exploitation of marginal or complex ores. The fifth sample was submitted by engineers of the Defense Minerals Exploration Administration.

Jan 1, 1956

By F. S. Wartman

This paper gives an account of the production of ductile-grade titanium powder in 100-pound batches by reduction of purified titanic Chloride with magnesium, grinding, leaching, and magnetic-separation of the reaction product. Apparatus, technique, and methods of controlling product quality are described and some data on operating costs are given.

Jan 1, 1949

By Martin D. Conyac

Results of the minerals survey indicate low potential for the discovery of placer gold along Deck Creek aid for copper, silver, and gold in PreTertiary rocks within the boundaries of the Lake Fork RARE II area. Potential for oil, natural gas, coal, and geothermal resources is negligible. No evidence of economic mineral resources was found during the examination of the study area, and no assays of rock or placer samples taken from the urea showed economic mineral values. There are no producing or developing mines within the boundaries o of the lake Fork study area. SETTING Mining Districts The Lake Fork RARE II area is on the eastern fringe of the Cornucopia Mining District, which is centered about 6 mi west. It is also on the western edge of the Homestead district, centered about mi east.

Jan 1, 1983

By H. E. Powell

The magnetic susceptibilities of 34 manganese-bearing minerals were determined. The source of each sample and petrographic, spectrographic, and chemical analyses are given. Included are values for ismorphous series showing wide ranges of composition and for a few high-purity synthetic minerals.

Jan 1, 1968

By S. D. Cramer

Corrosion research is being conducted by the Federal Bureau of Mines to determine suitable construction materials for geothermal resource recovery plants. As part of this research, the corrosion resistance of 31 iron-nickel-, aluminum-, copper-, titanium-, and molybdenum-base alloys was characterized and evaluated in laboratory corrosion studies in low-and high-salinity geobrines representative of those found in the Imperial Valley, Calif. General, crevice, pitting, weld, and stress corrosion were measured at 105° and 232° C in deaerated brines and brines containing dissolved 02, C02, and CH4 General corrosion rates in deaerated brines at 105° and 232° C were usually below 5 mpy for the alloys tested except carbon steel, the low-alloy steels, Monel 400, 70-30 cupronickel, and the aluminum-base alloys. Dissolving carbon dioxide and methane in the brines at 2320 did not markedly alter these results. However, the introduction of oxygen, which can enter the brine during process operations, seriously degraded the corrosion resistance of many alloys by increasing the incidence of stress corrosion cracking, crevice corrosion and, except for the titanium-base alloys, pitting. In deaerated brine at 2320 C, the general corrosion rates for carbon steel and the low-alloy steels were relatively unaffected by pH in the range of 6.1 to 3.0. However, general corrosion rates increased sharply below pH 3.0. In deaerated brine at 232° C, welds in several iron-, nickel-, and titanium-base alloys corroded at rates comparable to the general corrosion rates of the alloys, but the addition of oxygen to the brine increased corrosion rates for welds in Inconel 625 and E-Brite 26-1. Alloys exhibiting good corrosion resistance in the deaerated Salton Sea KGRA-type brine at 232° C were E-Brite 26-1, Inconel 625, Hastelloy S, Hastelloy G, Hastelloy C-276, TiCode-12, Ti-0.2Pd, Ti-2Ni, Ti-1.7W, and TZM. The alloys most resistant to corrosion in oxygenated Salton Sea KGRA-type brine at 232° C were the titanium-base alloys. These alloys appear the most suitable for use in the construction of geothermal resource recovery plants. Carbon steel and the low-alloy steels are unsatisfactory for high-temperature, high-salinity brines and alternative low-cost materials with improved corrosion resistance should be sought.

Jan 1, 1980

By Roger G. Long

In May 1973, the Bureau of Mines asked Arthur D. Little, Inc. (A DL) to investigate existing industrial communication standards that may be applicable to the problem of developing standards for mine communication, considering that the standards that may ultimately be developed will require simple field procedures for the industry and the inspectorate to determine that communication systems are properly functioning. The emphasis on this study is on telephone communications as related to coal mine applications. B. TASKS The tasks agreed upon for this program were as follows: 1. "Investigate the current practices and existing standards of other industries under government regulation. 2. Determine applicable methods for industry personnel and inspectors to ascertain conformance on-site with minimal test hardware. 3. Review the Bureau's approval, testing and inspection procedure as it may impact the development of such standards. 4. From the above studies investigate the development of installation and performance standards for mine communications, including voice and telemetry. 5. Prepare a written report specifying what standards and field inspection techniques are applicable with recommendations for development of subsequent data and ultimately standards and field inspection techniques. 6. Prepare a written summary of the findings of various investigations with an appendix covering the detailed findings of each investigation. 7. Prepare a list of suggestions of additional assistance the Bureau might require in subsequent phases of developing communication standards and means of ascertaining performance."

Jan 1, 1973

By Barbee J. Scheibner

This Bureau of Mines report describes the geology and physical properties of core samples at the Sunnyside coal mine No. 1, Sunnyside, Utah, and was written in conjunction with the Single-Entry Program conducted at the mine. The objective of this program was to test the hypothesis that the single-entry system in the Sunnyside mine, supported in the center by open cribs and divided by a fire-resistant partition, is equivalent to or better than a two-entry sys-tem. Drill cores, taken underground at 15 sites in the single-entry study area, facilitated the construction of geologic cross sections of the entries. Physical property data obtained from the drill cores was used in a three-dimensional finite element analysis program to evaluate the stability of the openings, the support requirements, and the de formation characteristics of the roof and floor material. Data on 10 physical property parameters for 5 rock types plus coal are also tabulated and discussed.

Jan 1, 1979

By George A. Morgan

The 53 countries that constituted Africa in 1990 accounted for a significant portion of total world output of a number of mineral commodities. Among the most significant to be produced in Africa were andalusite, antimony, asbestos, bauxite, chromite, coal, cobalt, copper, diamond, fluorspar, gold, lithium minerals, manganese, phosphate, platinum-group metals, the titanium minerals-ilmenite and rutile, vanadium, vermiculite, uranium, and zircon. Several of these, chromite, cobalt, diamond, and manganese, were not produced in the United States. Despite the underdevelopment of much of Africa, mineral raw materials playa very important part in the national economies of many of its countries. In many cases, the production of minerals is the dominant economic activity in the country, often having the largest and most sophisticated work force. In several countries, one or two mineral commodities are dominant in a weakly diversified economy. Among these are petroleum and diamonds in Angola, petroleum in the Congo, gold in Ghana, bauxite in Guinea, uranium in Niger, phosphate in Senegal and Togo, and copper and cobalt in Zaire and Zambia.

Jan 1, 1992