Search Documents

By A. A. Berk

Other Federal agencies have been coming to the Bureau of Mines for help with the purchase and utilization of fuel, largely coal, almost since the day the Bureau was created in 1910. The requests covered a wide range of fuel-economy problems and included boiler-water treatment after it became apparent that water-formed deposits on heating surfaces acted as insulators, decreasing heat transfer and impairing fuel efficiency. Dr. Ralph E. Hall, a Bureau of Mines physical chemist determined the reactions that cause adhering scale to form in boilers (7)2 and went on to introduce scientific principles into water treatment for scale prevention (8). Widespread publicity of these achievements increased the requests for help from Federal steam-generating plants. Since no other Federal agency (even those which were more directly concerned with testing water) wanted to provide boiler-feedwater service, the Bureau decided to continue to give requested help to Federal agencies, Later, the Congress endorsed such agency cooperation as an economy measure,

Jan 1, 1963

By Eugene T. Sheridan

The Bureau of Mines annually canvasses the peat producers in the United states and publishes economic data on the peat industry, based upon reports submitted by producers. This publication lists all producers that reported commercial production to the Bureau for 1960 and presents data on individual plants. The companies named herein represent virtually all commercial producers, although a few small companies may not have been canvassed as the industry has many small operations that operate intermittently. Output of the various companies listed ranged from a few tons to more than 50,000 tons. Peat is included in the Bureau's annual surveys of the mineral industries because peat is classified as a mineral fuel. Although none is used for fuel in the United States, peat is a potential source of energy and ranks as one of our large mineral resources. The domestic peat industry sells peat, chiefly, for use as a soil amendment for general soil-improvement purposes. During the past decade the industry has expanded rapidly with operations increasing from 45 in 1947-494/ to 115 in 1960. Output during this period has more than tripled, increasing from 131,782 short tons to 470,889 short tons.

Jan 1, 1961

By K. Y. Haramy

Coal mine bumps involve the violent, rapid failure of coal and rock around a mine excavation. Deep coal mines with strong roof and floor rocks and high-stress conditions frequently experience face and rib bumps. The bump problem is becoming more severe as mining depth increases, prompting efforts to control high stress in advance of mining. This Bureau of Mines report presents a review of the most widely used methods to detect and destress high-stress zones along coal faces and an investigation of stress-related bump problems and destressing techniques at a cooperating mine. Geotechnical instrumentation and microseismic methods were used to better understand bump occurrences in underground coal mines. Laboratory tests of the drilling-yield method for high-stress detection were conducted to determine the correlation between the volume of cuttings obtained and the magnitude of the applied stress at various confining pressures. A three-dimensional, multiple-seam computer modeling program, MULSIM, was used to evaluate the effectiveness of stress-relief methods. Modeling results indicate that dangerously high-stress areas can be controlled by either proper planning or destressing. Proper mine planning guidelines and destressing methods such as volley firing, hydraulic fracturing, and auger drilling are discussed.

Jan 1, 1988

By R. W. Barnes

This circular presents results of a survey conducted by the Bureau of Mines to ascertain the extent to which dust-control practices are employed in the coal-mining industry. This survey was initiated because of increasing realization of the possible harmful effects of the inhalation of dust upon the health of coal-mine workers and the advent, during recent years, of new types of mining machinery and new mining methods that may have a direct effect upon the extent of exposure to airborne dust experienced by persons mining coal. Anthracite Mines The survey covered 169 anthracite mines that were operating from November 1, 1953, to July 1, 1954. It showed that large mines employing more than 100 men were doing most to control dust produced during mining.

Jan 1, 1956

By J. S. Miller

This report presents a complete coverage of results from Bureau of Mines preliminary research and the field application of explosive fracturing techniques to prepare oil shale for in situ recovery of shale oil. Small-scale surface tests were conducted to determine the feasibility of using a nitroglycerin-base explosive for creating rock fractures. Prior to underground testing, surface and near-surface tests with liquid explosives showed that explosions in sheetlike layers simulating underground fractures would propagate effectively. Successful surface experiments were conducted using layers of explosive placed between glass plates and explosive-saturated sand confined in small-diameter metal tubes. The tests in glass-plate reservoirs and metal tubes demonstrated that nitroglycerin would detonate and the explosion would propagate in cracks as thin as 1/32 inch and through distances up to 12 feet. In a shallow field test, nitroglycerin was detonated in a vertical crack in limestone and produced extensive fracturing. Explosive fracturing tests were performed in oil shale formations on seven sites near Rock Springs, Wyo. The procedures included (1) displacing and detonating nitroglycerin in natural or hydraulically induced fracture systems; (2) detonating nitroglycerin in wellbore shots; (3) displacing and detonating nitroglycerin in induced fractures followed by wellbore shots using pelletized TNT; and (4) detonating wellbore charges using pelletized TNT. The research on oil shale formations demonstrated that nitroglycerin displaced in a natural or hydraulically induced fracture would detonate, and the explosion would propagate through the explosive-filled fracture. Shooting a pattern of wells in oil shale at 100-foot depth with wellbore charges of pelletized TNT developed a satisfactory interwell fragmented zone. Tests performed on other sites at depths to 385 feet caused fragmentation of rock around the wellbore and provided interwell communication. Fourteen methods used to evaluate the extent and degree of fragmentation in the explosive fractured oil shale are discussed.

Jan 1, 1974

By Mark I. Copeland

A study was conducted to determine if commonly used alloying additions or coating materials can prevent the formation of a liquid-copper phase during the reheating of copper-containing steels. If so, the tendency of such steels to surface-crack during hot-working might be eliminated. Steel specimens were scaled by heating them either isothermally or in a programed manner that simulated industrial furnace practice. Metallographic examination of the heated specimens showed that molten fayalite (Fe2Si04) completely prevented the formation of liquid copper at the surface. Fayalite, which melts at 2,200° F (1,205° C), was formed by internal oxidation of the silicon contained in the steel. By forming complex molten oxides, coatings of borax glass were also effective in preventing the occurrence of liquid copper at the steel surface.

Jan 1, 1972

By Sidney Katell

This report, covering the period January 1967 through December 1967, is a continuation of a series that began with the publication of Information Circular 7516 in October 1949. It is the ninth in a series of reports prepared in cooperation with the American Association of Cost Engineers. The abstracted articles are concerned with all phases of cost engineering in the field of chemical and petroleum plants and related subjects. They are from the following sources: 1. American Association of Cost Engineers Bulletin. 2. Bureau of Mines Information Circulars. 3. Bureau of Mines Reports of Investigations. 4. Chemical Engineering. 5. Chemical Engineering Progress. 6. Chemical Week.

Jan 1, 1968

By D. Harrington

Although the explosion-fatality record for the fiscal year 1944 showed considerable improvement over those of the preceding 4 years, it is still fur from creditable, and the coal-mining industry and agencies interested in the prevention of coal-mine accidents should not be satisfied until accidents from explosions and fires are eliminated. In view of present knowledge of the methods of preventing explosions and fires, such disasters are inexcusable and discredit the mining industry. Despite this knowledge, far too many coal¬mine operators and employees continue to follow procedures that have resulted in disasters in the past. Included in the appendix to this circular are a number of safety measures designed to prevent coal-mine explosions and fires and metal-mine fires. Their adoption is essential if explosions and fires are to be prevented, as certainly they should be. An epidemic of disastrous mine fires of electrical origin during the past 2 years emphasizes the need for better methods of protection of underground electrical circuits. At present, committees of mining-electrical engineers, electrical-equipment manufacturers' representatives, and others are cooperating with the Bureau of Mines seeking means to solve this problem.

Jan 1, 1945

Rock property tests were performed on NX-size diamond drill core from the roof, floor, and coal from the longwall mining section of Federal No. 2 mine, West Virginia. The purpose of these tests was to determine the engineering properties of the various strata as part of a ground control study of the longwall operation. The following tests were performed: 1. Uniaxial compressive strength, Young's modulus, and Poisson's ratio 2. Triaxial compressive strength 3. Brazilian tensile strength 4. Modulus of rupture 5. Specific gravity Thirteen boxes of core delivered to the University on April 1, 1974 were identified as follows: 2 PTR 1 -2 boxes of roof rock 2 PTF 1 -2 boxes of floor rock 2 PTR 2 -2 boxes of roof rock 2 PTF 2 -2 boxes of floor rock with approximately 3 ft of coal in Box 2 (designated 2 PTC 2) 2 PTR 3 -2 boxes of roof rock 2 PTF 3 -2 boxes of floor rock 1 PC 5 -1 box of coal

Jan 1, 1976

By R. H. Hiltz

The Coal Mine Health and Safety Act of 1969 legislated maximum dust levels for the working place. As the law was implemented, extensive efforts were undertaken to provide the technology necessary to control dust generation. One approach to dust control was the use of high expansion foam in place of the usual water sprays on coal cutting equipment. At the time of the act, high expansion foam had already seen considerable testing for the suppression of dust in underground coal mines. Work by MSA, several coal companies and the Bureau of Mines itself had provided data which showed foam to have some merit as a dust control mechanism. It suffered in a few areas, however, which limited its practical application. Its principal difficulty was persistence which hampered operations due to foam buildup, but problems were also encountered due to equipment size and form.

Jan 1, 1975

By R. Pallini

The Franklin Research Center (FRO, a Division of The Franklin Institute was contracted by the U.S. Department of Energy to investigate the application of elastomeric materials for the purpose of smoothing loads on dragline thrust rollers. This report covers the design, fabrication, and demonstration of a portable- device for measuring roller circle track deviations and roller loadings. The results of this work are documented in this report. During December 1981, a field test group visited the Falkirk Mine, Underwood, North Dakota for the purpose of demonstrating the use of the designed and built device. The data collected indicates the practicality and usefulness of such a device for determining actual dragline roller circle roller loads, while the dragline is in service. The device was useful in determining roller load peaking that may be a contributing Factor in the premature failure of these thrust rollers. The device could be used for field evaluation of elastomeric cushioning materials used to eliminate these load peaks.

Jan 1, 1982

By Mark S. Sanders

Six underground coal mine shuttle cars (three high seam and three low seam) were used to assess visibility using the concept of visual attention locations (VALs) and an improved human eye reference measurement instrument (HERMI Mark II). Each machine was assessed in the inby and outby direction of travel with no canopy and with the canopy in its highest, and lowest position. In addition, the illumination level at each VAL was determined. Results showed that the most important variable determining visibility was operator eye position. When this variable is controlled, the addition of a canopy has no effect on visibility. Further, with eye position controlled, there is no difference in visibility between high and low seam machines. The visibility and illumination assessments found blind spots in the operator's field of view located on the opposite side of the car from the operator and ahead of the machine. Suggestions for reducing the blind spots were made. The report also included a procedure manual for using HERMI and the system of VALs to assess visibility from underground shuttle cars, continuous miners, and scoops.

Jan 1, 1983

By G. W. Jones

In a previous report'/ results were given and a method outlined whereby from a knowledge of the composition of the natural gas and of the inflammability limits of the individual constituents composing the natural gas, the limits of inflammability of natural gas and air mixtures could be closely calculated. This method is based on the application of Le Chatelier's law as modified by Coward, Carpenter and Payman,5/ to apply to a mixture of any number of combustible gases. This law must not be used indiscriminately, because many exceptions have been found. For example, when ethylene, acetylene, hydrogen sulphide, or chlorinated hydrocarbons are present the law may not hold. For a discussion of the many exceptions which have been found, reference should be made to a report by Coward and Jones.6/

Jan 1, 1933

By Terry J. Close

From 1981-84, Bureau of Mines personnel examined and evaluated mines and prospects in the highly mineralized 62,400 acre Inyo Mountains U. S. Bureau of Land Management (BLM) Wilderness Study Area (WSA), located east of Lone Pine, CA. The 62,400 acres studied is the part of the 87,145 acre WSA designated as suitable prior to February 28, 1983. The WSA is underlain principally by quartz monzonite and quartz diorite that have intruded sedimentary and volcanic rocks. Three types of mineral deposits are present: 1) gold in fissure veins, 2) silver in fissure and replacement veins, and 3) talc in metasomatic lenses. Of the 84 nines, mills, and prospects examined, 54 are significant: 1) 5 in the intrusive rocks total about 4.4 million tons of inferred marginal gold reserves averaging 0.24 oz gold and 0.74 oz silver/ton; 2) three associated with intrusive-sedimentary rock contact zones total about 280,000 tons of inferred subeconomic silver resources averaging 7 oz silver/ton; 3) 27 gold and silver occurrences in the intrusive and sedimentary rocks total about 1.2 million tons of material in poorly defined bodies too small or low grade to be resources; 4) 15 gold and silver occurrences in the intrusive and sedimentary rocks are too poorly exposed to estimate tonnage and grade; and 5) four talc deposits along intrusive-sedimentary contact zones have inferred marginal reserves totaling about 640,000 tons. The marginal gold reserves at $450/oz might be profitably mined (reserve) at a gold price of about $600/oz and the subeconomic silver resources at a silver price in excess of about $27/oz. The marginal talc reserves might become minable at prices of about $50/ton and $80/ton for unprocessed and processed talc, respectively, after present supply sources are depleted. At most of the 54 significant mines and prospects, additional reserves or resources would likely be disclosed by trenching or drilling. Present in the WSA are 13 gold mills, numerous small pits and cuts, 270 underground workings totaling about 36,000 ft, and 80 mining benches totaling about 11,000 ft. Gold, silver, or talc were produced from most of the workings. A total of 1,561 lode and 18 placer samples were taken.

Jan 1, 1985

By Richard H. Bares

The general or macroclimate of the study sites in western North Dakota is characterized by rapid and sometimes extreme daily and day-to-day temperature fluctuations, rainfall patterns which are erratic in spatial and temporal distribution and intensity, generally low relative humidity, plentiful sunshine, nearly continuous air movement, and a relatively short frost-free period. Of particular relevance to plant growth and productivity is the mosaic of microclimates: these microclimates are affected by landform (convex and concave surfaces); exposure; slope angle, length and aspect; soil color, texture and surface cover (litter), and vegetation cover. The most critical plant growth governing factor in this region is available water. It is determined principally by water input (precipitation) and water loss (evapotranspiration) which is increased by high temperatures, wind, and poor litter and vegetation cover. While spring and fall precipitation is generally gentle and soil-soaking summer rains frequently come in the form of intensive, soil-washing, localized convective thunderstorms of short duration. Due to the convective nature of these storms, summer rainfall is particularly affected by regional topography; southwest slopes and crests often receive more rainfall since these storms usually move in a northeasterly direction. The water loss due to runoff and consequent soil erosion arc major problems resulting from such "cloudbursts". Previous fall precipitation (September - October) when added to current seasonal precipitation (March - August) was found to be significantly correlated (r-.93) with plant production. Winter precipitation (snowfall) is relatively light as the prevailing weather is dominated by dry polar air masses from the north. The nearly continuous wind is responsible for removing snow from open exposures and depositing it in depressions and windbreaks. Although the winter precipitation is not a large component of the total annual precipitation, conservation of that which does occur would contribute to plant production during the following growing season. Generally clear skies over the region facilitate receipt of abundant sunshine at the earth's surface. While good for early season soil warming and plant photosynthesis, this abundant sunshine coupled with long days and nearly continuous wind is responsible for evapotranspiration exceeding precipitation by an average of six inches between June' and September. On a local (micro) scale, the water deficit is most severe on the southern exposures which receive the most direct (most effective) solar radiation and therefore are warmer than other exposures. On a broader scale, it was found that ambient temperature extremes were slightly but significantly greater in the town of Beulah in the Knife River Valley than at the upland test sites, This may have been due to the difference in topography and/or the "urban heat island" effect. It is known that air temperatures in large cities may be 2° to 4°C higher than that of the surrounding countryside. It is also well known that basins, depressions or valleys are sinks for cold air masses and are often subject to frosts not occurring on adjacent upland sites.

Jan 1, 1982

By E. W. Dean, H. H. Hill

Gasoline has become of such commercial and military importance that it is now practically indispensable. This product is of special interest because, in addition to realizing its value, the Nation is learn- ing that the raw materials from which gasoline is obtained are not unlimited. ACTIVITIES OF THE BUREAU OF MINES IN PROMOTING EFFICIENCY IN THE PRODUCTION AND UTILIZATION OF GASOLINE. The Bureau of Mines has directly and indirectly worked for the conservation and efficient utilization of this important product. Some of the bureau's activities have been along lines widely different from those reported in this bulletin. The work of the bureau toward the increase in efficiency of processes for the production and refining of crude oil is too well known to need mention here. Another line of activity in which the bureau has engaged is the collection and publi- cation of statistics on refinery operations. Finally, as immediate preparation for the present bulletin, two surveys of the gasoline mar- keting situation have been made. The primary object of this bul- letin is to make available to the public information obtained in con- nection with these surveys. PURPOSE OF THE GASOLINE SURVEYS OF 1917 AND 1919. Shortly after the United States declared war on Germany the bureau collected gasoline samples in the retail market throughout various parts of the country. Information regarding the sources of these gasolines and the details of marketing them was obtained, and they were subjected to analytical tests which furnished conclusive informa- tion regarding their properties. The information obtained through this survey proved of inestimable value both to the bureau and the United States Fuel Administration, particularly in drawing up speci- fications and in ascertaining the best means of obtaining supplies of particular types of gasoline that were needed. A similar and more extensive survey was made in the months of April and May, 1919, in order to obtain data needed for the revision of the Federal motor gasoline specification. The specification adopted during the war had been the subject of numerous complaints, and it seemed desirable to determine whether or not these objections were valid before attempting revision.

Jan 1, 1920

By Frank D. McGuirk

Underground coal mining is traditionally hazardous. Although many danger-prone human activities are now performed by mechanized equipment, this mechanization has itself brought new dangers to the underground mining industry, and the loss of life and limb has caused increased concern for mine safety. The 1969 Federal Coal Mine Health and Safety Act has precipitated a great deal of safety-related research on the part of the Government, industry, and private agencies. Much of this safety research has been focused on the new and varied man-machine interfaces caused by increased mechanization. Recent projects in this area have dealt with standardized controls, emergency shutdown capabilities (panic bars, strike plates, self-centering controls, "dead man" controls), and machine operator protective devices (fully enclosed cabs, canopies, side rails). There was a need for integration of the findings of current and past projects to move rapidly toward the smooth, orderly implementation of standardized operator work station designs for underground mining equipment.

Jan 1, 1975

By James L. Ash

This report contains the results of a technical and economic evaluation of conceptual systems for the underground mining, rubblization; and in situ retorting of deep oil shale deposits. Study efforts were first directed towards evaluation of the applicable geology, associated minerals, rock mechanics, in situ retorting, access mining, ventilation, rubblization, safety, and environmental impact factors. Conceptual systems were synthesized and then evaluated against these factors from both a technical and limited economic viewpoint. The results of these evaluations were then analyzed 'and, based upon this analysis, the following two systems were selected for further study: System II: Room and Pillar-Vertical Drill and Blast System IV: Tunnel Boring-Horizontal Ring Drill and Blast Due to the large number of variables to be considered, a computer program was developed and utilized to provide data for the cost trade-off studies and economic analysis. Results of the early computer runs indicated the value of the tool available in the computer program and led to an extension in the contract to determine the sensitivity of the systems to several of the more apparent significant variables. These results in turn led to a refinement in the design assumptions and a better understanding of the technical and economic options available to an owner-operator of a Vertical Modified In Situ Shale Oil Extraction System. This report is submitted in fulfillment of the requirements of Contract Number S0241073 by Fenix & Scisson, Inc. to the Denver Research Center, United States Department of the Interior, Bureau of Mines. Work was completed as of November, 1976.

Jan 1, 1976

By Gary E. Sherman

To aid the U.S. Army Corps of Engineers in their Resource Development Navigation Study, the U.S. Bureau of Mines (Bureau) examined the potential for mineral development near ten Alaska port sites. This report presents the results for the following four sites: Balboa Bay, Beluga, Lost River, and Point MacKenzie. There are 579 known deposits within the area considered for these ports. The majority of the deposits are located within a highway/railroad corridor examined for the Point MacKenzie port site. Based on the current level of knowledge, coal deposits near the Beluga and Point MacKenzie port sites are most likely to be developed in the near future. This conclusion is based on the fact that coal projects in these areas are actively being pursued for development. The mineral wealth surrounding the four port sites is substantial. Mine models were used to examine the potential for mining tin, gold, silver, copper, and molybdenum. The models were based on published reserve and grade data and therefore do not include proprietary company data which, if available, would likely change the analysis results. Of the models examined, the tin placer mine model developed for the Lost River port site proved to be closest to being economic.

Jan 1, 2011

By Edward W. Parsons

The transverse force developed by expansion-shell rock-bolt anchors on the wall of a drill hole as the bolt is tensioned was measured by the Bureau of Mines using a device specially designed and fabricated for attachment to a universal testing machine. Load cells equipped with electrical-resistance strain gages provided the data from which the transverse force, in pounds, was calculated. Seven different expansion-shell anchors were tested, and the ratio of transverse force to bolt-tension load was found to range between 0.98 and 1.94 to 1.0. The drag load appeared to be the major cause of the transverse-force variation, but the relative effects of individual factors that affected the ratio between the transverse force and the bolt tension were not determined.

Jan 1, 1968