Search Documents

By Andrea Francioso, Roberto Folchi

In order to comply with the latest European Highway Standards, the highway Salerno - Reggio Calabria, in southern Italy, had do be widened and upgraded to reduce its vulnerability to earthquakes. Reinforced concrete viaducts, no longer needed for the new road, had to be demolished. Many bridges still to be used for the highway required refurbishment due to 50 years of wind, frost and salt corrosion. This re-furbishment and new construction had to be carried out simultaneously. To keep the highway open dur-ing the renewal process, all traffic was directed to one side of the road. Demolition was conducted ex-tremely close to operational roadways and viaducts, as close as only 2 cm (0.8 in). Care had to be taken to ensure that the stresses (vibration levels), resulting from the demolished pylons and decks hitting the ground, were below the no-damage thresholds for the nearby acceptors (structures receiving the vibra-tion stresses). These structures included bridges, houses and buried pipelines (water, oil and gas). In some cases, care also had to be taken to preserve the existing pylons supporting decks that were being demolished; since the same pylons were going to be used for the new viaducts (bridges). New continu-ous decks in weathering steel replaced the old reinforced concrete decks.

Jan 1, 2013

By Alexandra Yuyali

The objective of this research work is to increase the drilling ratio represented in tons per drilled meter (ton/m) to reduce mining costs. One of the key characteristics of this research is the use of the ITH (in-the-hole) drilling rig with a water-powered hammer, also known as Wassara™. The patented Wassara™ in-the-hole hammer is powered by high-pressure water instead of air. To reach the objective, a new design of the blast pattern was implemented considering the following: Burden from 1.7 m (5.6 ft) to 2.8 m (9.2 ft) Spacing from 1.7 m (5.6 ft) to 2.7 m (8.9 ft) Drill diameter from 89 mm (3.5”) to 102 mm (4”) Drilling length from 15 m (49 ft) to 30 m (98 ft) Borehole deviation < 2% The result of this new design is the optimization of the drilling ratio (ton/m); having as a baseline 5.2 ton/m with traditional equipment and obtaining 13.7 ton/m with the ITH drilling, which generates annual savings of $2.43M.

Jan 21, 2025

By Ian Bell, Shahram Tafazoli, Bahram Sameti, Aylin Azmin, Edmond Chow, Nima Ziraknejad

Image-based rock fragmentation analysis methods have been applied by blast engineers to estimate rock size distribution for over 25 years. These methods utilize a wide range of image segmentation techniques, from manual to fully-automated, to delineate the edges of the rocks in the image. In most commercially available image-based rock fragmentation analysis systems, rock delineation results are converted to physical rock sizes by introducing one or more reference objects (e.g., basketballs or other objects with known geometry) to the scene as size-scaling references.

Jan 1, 2014

By Francisco Sena Leite, Thomas Palangio, Vinicius Miranda

With an increasing pressure to find efficiencies in the mining industry, operations are looking for continuous improvement tools to validate blasting procedures, a crucial and often overlooked area of the process. Using case studies completed at both small and large-scale mining operations, this technical paper proposes a practical methodology for pattern expansion studies, taking into account terrain parameters, rock quality and explosive strength. This technical paper will use a series of tools geared towards an economical continuous improvement procedure, using UAV particle size analysis to optimize blasting based on “generalized reduced gradient” for non-linear problems, with cost savings being the main objective. For the validation of this methodology, one scenario was created based on the operation’s budget: an economical continuous improvement plan that relied on manual data collection methods in order to baseline and optimize procedures.

Jan 1, 2018

By Braden Lusk

Vibrations as a result of blasting practices in mining engineering are a complex phenomenon controlled by many variables. Mine blast vibration modeling and prediction is becoming more important as a consequence of interactions by mining activity with an ever closer public. Many communities (all over the world) close to mining activity often complain about airblast and vibrations produced from blasting activity. It is important for the mining industry to have tools and understandable methodologies to model and predict blast vibration. These tools can then be used to predict and control vibration at neighboring structures.

Jan 1, 2013

By Robert Hopler

THIS paper deals specifically with heading-driving as distinguished from the broader term tunnel-driving. A heading is a pilot or path-finder for the main tunnel. Some headings are complete tunnels in themselves; that is, conditions at times warrant driving a heading the full diameter of the proposed tunnel. A tunnel 10 ft. in diameter might be driven to advantage through a single heading, provided the nature of the material admits, but it usually pays to drive rock tunnels of large diameter through the headingand-bench system. Much depends upon the material, as in soft ground tunnels of much larger diameter are driven in a single heading.

Jan 1, 2010

By Ashley Haslett

A European Directive on Identification & Traceability of explosives came into effect on the 4th of April 2008. This directive is intended to establish a harmonised system for the unique identification and traceability of all packaged explosives, detonators, reels of detonating cord and primers used in civil applications across the European Union. The directive must be adopted into the national legislation of each European Union member state by the 5th of April 2009 with compliance achieved throughout Europe by the 5th of April 2012. The requirements of the Directive apply to all explosives manufactured, used and imported into the European Union from 5th April 2012.

Jan 1, 2010

By John A. Davis, David W. Brunton

(Excerpts, pp 157-160) The usual means of firing blasting charges, especially in tunnels and adits in the Western States, is by the use of a safety fuse. The term safety fuse originated from the fact that when properly used under working conditions this fuse burns at a uniform rate and does not flash or explode, as was often the case with the means employed for igniting blasting charges previous to its invention; but the term is somewhat misleading, because the fuse is not, nor has it ever seriously been claimed to be, safe for use in gaseous coal mines. The fuse used for tunnel work is composed of a core of gunpowder surrounded by various layers of waterproofing material.

Jan 1, 2015

By Richard H. Granhom

Detonation pressure, or Chapman-Jouguet pressure, is an intrinsic property of an explosive, and like detonation velocity, is an indicator of explosive performance. Pressure and velocity are also important for calibrating computer codes and for other calculations such as the stress imparted to rock or metal by an explosive. The detonation pressures, P~cj, of many "ideal" explosives have been measured indirectly by recording some hydrodynamic flow variable other than pressure, with P~cj being inferred from hydrodynamics and the assumed Chapman-Jouguet equations. One such method is the difficult and expensive "aquarium technique''.] Commercial explosive manufacturers generally rely on estimates of P~cj generated by computer codes not explicitly designed for non-ideal explosives typically used in commercial applications. Over the last decade, U.S. national and government laboratories have developed in-situ gauge techniques such as the manganin gauge, for direct measurement of detonation pressure. Manganin is an alloy of copper, manganese and nickel, and is ideally suited for use as a pressure transducer because its electrical resistance changes with pressure, but is nearly constant with changes in temperature. A simplified manganin gauge technique adapted for use at a commercial test site is described and some initial results from measurements on commercial emulsion explosives are presented.

Jan 1, 1991

By Guillermo Lazcano Ríos, Jorge Parvez Aguirre, Alejandro G. Díaz Berríos, Felipe Rodriguez Alveal

Codelco's Chuquicamata Underground Division (DCHS) faces issues due to collapses in its subsidence streets, which hinders the advancement of the subsidence front and leads to the loss of areas and reserves. To address these issues, DCHS and Orica have developed a new excavation methodology based on pre-loading explosives in high drawbell. This methodology involves creating a high drawbell extending from the floor of the production level to the ceiling of the subsidence level, divided into two phases: upper and lower. A resin stemming is used to separate these phases. The excavation strategy adjusts to variables such as reception volume, fluffing, and excavation geometry, involving vertical pre-loading of the explosive and the use of a separating element between the phases. The test aims to validate the new excavation methodology and the retaining element in the rock mass, evaluating aspects such as drawbell geometry, impact on the rock mass, damage to the retaining element, and fragmentation. Wireless electronic detonators are used in the upper phase to improve safety by eliminating the need for physical connections, while traditional electronic detonators are employed in the lower phase. Low-density bulk emulsion is applied to minimize the impact on the Crown pillar and extraction point, and higher-density explosives are used above the subsidence level to ensure good caving. Results showed that the blast achieved 86% conformity with the theoretical design. Resin stemming allowed for 100% effective detonation in the upper columns, and the fragmentation obtained was 5.44 inches, which was less than expected. No damage to the Crown pillar was observed, and the explosive quality met standards. This technique has proven to be effective and viable, suggesting the possibility of eliminating the subsidence level in future levels, resulting in savings, and providing greater stability to the rock mass.

Jan 21, 2025

By A T. Spathis

Corrections are given for “A three parameter rock fragmentation distribution” by A.T. Spathis (Measurement and Analysis of Blast Fragmentation, Workshop hosted by 10th International Symposium on Rock Fragmentation by Blasting, New Delhi, India, November 25-29, 2012 pp. 73-86). Typographical errors in two equations for the uniformity index in the two versions of the original and modified Kuz-Ram model are corrected. It is noted that the modified equation in the original published paper of Cunningham also had the same typographical error. A corrected plot of the dependence of the uniformity index versus the burden to diameter ratio is given. These corrections do not affect the rest of the original published paper.

Jan 1, 2013

By Jeffrey W. Lin, Larry B. Weston, Jonathan D. Abbott, Jordan L. Arthur

Hydrocarbon fuel oils are one of the main components of ammonium nitrate-based explosives, including ANFO (Ammonium Nitrate-Fuel Oil) and emulsions. While a wide variety of fuels can, and have, been used in the manufacture of ANFO and emulsion products, No. 2 diesel, particularly dyed, off-road diesel, is widely used due to its ready availability and use in fueling mining equipment. However, a number of alternatives to standard diesel have been introduced over recent years, namely, biofuels, ‘high-performance’ diesels, and renewable diesels. The pressure to adopt these alternative fuels come from a variety of sources, such as initiatives to reduce carbon footprints, increased lifetime of equipment, and cost-advantages from tax credits. While these factors may provide a very real benefit to the mine site, a consideration that is often missed is how the use of these fuels can impact the formulation and characteristics of the ammonium nitrate-based explosives. Herein will be presented a discussion of these alternative fuels from a chemical perspective as well as the results of several studies focused on how the inclusion of various alternative diesels influences the production and performance of ammonium nitrate explosives. ANFO and emulsion were manufactured using representative fuel sources and studying in terms of the manufacturing parameters, shelf-life, interaction with other chemicals using in mining explosives. Detonation data was then collected for these products and compared to the behavior of products made with standard diesel fuels.

Jan 21, 2025

By W C. Brukle

Our title for this presentation could be taken in many ways. One course would be terrifying and that would be to cite incredibly bad practices. All of our votes/efforts should be for the reverse direction in which everyone does his/her best to keep their pit or working place free from hazards.

Jan 1, 1983

By Thad M. Jones

This paper considers the sampling, digitizing and reconstruction of seismic signals. A sampling frequency range is proposed and a minimum limit is suggested. Digitizing precision criteria for both peak velocity and analysis applications are given. Several methods for reconstructing signals from sampled data are presented.

Jan 1, 1985

By Tom Goforth, Rongmao Zhou

The interest of seismologists in mining explosions has increased substantially with the construction of the International Monitoring System (IMS). The IMS supports the Comprehensive Nuclear Test-Ban Treaty by providing global data coverage from seismic, hydro acoustic, infrasonic, and radionuclide sensors that will detect a host of natural and man-made events at regional (<2000 km) distances. Ideally, the recorded data can be used to identify those events that have explosive characteristics and therefore might be clandestine nuclear tests. The regional observations assure the detection of mining explosions, and these must be properly identified to avoid false alarms of the monitoring system. Cooperation with the mining industry, including documentation of the firing programs, provides critical information necessary to characterize the seismograms.

Jan 1, 2006

By Stephen Chung, John Carpenter, Scott Gosch, James Breedlove

While controlling fly rock and ground vibration in quarrying in the neighborhood of a residential area, producing good fragmentation and keeping different grades of material separated in a muckpile are important in maintaining the productivity of quality aggregates. This paper describes a single row production blast for the study of fragmentation and displacement in the grade control carried out at a quarry of Barrett Paving Materials Inc. in Sylvania, Ohio. Digital video imaging was used to monitor the blast-induced motion of the bench face as input to the DMC_Blast (Distinct Motion Code), for the analysis of the formation of the muckpile. The actual digitized blast video and the DMC_Blast simulation are compared. The displacement and mixing of all the inter-bedded limestone layers are made visible in the simulated cross-section of the muckpile. The apparent fragmentation analysed with PowerSieve is also discussed.

Jan 1, 2001

By Paulo Couceiro, Juan Navarro

The impact of rock blasting fragmentation and heave on digging performance in open-pit mining operations is usually the first true indicator of blasting outcomes. Within the typical excavation cycle, the bucket loading time or instantaneous digging rate are the ones that present the strongest correlation with rock fragmentation size distribution, swelling, and shape of the muckpile, a part of rock mass hardness, equipment size, power, and others. As the efficiency of unit operations becomes increasingly important for long-term mining strategies, cost-effective approaches are needed to increase mine productivity. In this line, the performance of downstream operations, such as digging, hauling, and comminution, may be affected by the energy input in blasting. This requires a better understanding of the explosive’s energy role in such unit operations in order to drive consistent improvements. Therefore, this paper examines the impact of the explosive’s energy distribution on shovel diggability from production shots carried out with different explosives in an open pit gold mine, with the aim of modelling the interface between blasting and excavation.

Jan 21, 2025

By Carlos Enrique Arroyo Ortiz, Jadir Pedro Alves

This paper presents some of the results obtained during the research work about the use of technologies and digital transformation in the process of rock drilling in open pit mines. The use of automation presents itself as a disruptive factor and a driver of improvements that provide sustainability in rock drilling. Seven main operational parameters were utilized to combine measurement while the drilling (MWD) with other information generated by the equipment during hole drilling, in six different lithologies in an iron mine, located in the central region of Minas Gerais in Brazil. Adjustments and corrections were made to the data collected in order to minimize external influences other than the rock itself, to ensure the effectiveness of the analyses. Finally, we sought to compare the performance of the drilling process in manual and automatic operation modes. Thus, making it possible to show the efficiency and impact on the sustainability of rock drilling operations in open pit mines.

Feb 6, 2023

By W. Sharkey Bowers

This study was undertaken in order to determine a conservative estimate of the attenuation rate of vibrations through the shallow limestone in South Florida due to quarry blasting.

Feb 1, 2020

By Florian Bauer

The Fording River mine in British Columbia produces hard coking coal in an open pit operation. Coal seams are exposed by blasting overburden and digging blasted muck with rope shovels. The drilling and blasting process presents a considerable cost factor to the operation. Reducing the amount of explosives needed therefore contributes considerably to costs saving initiatives. However, reducing the powder factor only makes sense if the subsequent loading processes by the shovels are not compromised in terms of productivity.

Jan 1, 2014