Search Documents

By Neal Lee, Braden T. Lusk, Brendan McCray

Determining the minimum amount of inert material that can be used between explosive columns is a complex problem. Using too little inert material can result in detonator/primer failure, either by sympathetic detonation of or failure to fire of the subsequent explosive column(s). Propagation type failure results when inert material length between charges is small enough that the subsequent (delayed) deck fires more or less instantly. In this situation, the primer, detonator, or bulk product is initiated by the shock wave from the earlier firing deck. This type of failure may be un-noticed until the vibration/airblast report is examined.

Jan 1, 2016

By Chris Breeds, Ken Johnston, Omar Fulton

This paper describes the process typically involved with obtaining permits for quarry blasting in urban, suburban, and rural areas, including: content of SEPA (State Environmental Policy Act) driven documentation; regulatory review and comment; public interaction; public hearing(s); periodic regulatory review(s); negotiated solutions; monitoring; and the role of public interaction, demonstration(s), and education in the process. Case studies will be presented of projects undertaken in the State of Washington that illustrate the approach and regulatory interaction as well as the importance of public interaction throughout the process. Reference will be made to the role of national and state regulations and local codes and ordinances that provide additional limitations on blasting practice. The paper will also present regional blast monitoring data that are used in the permitting process and the layout and design of blast monitoring systems typically required as conditions of the quarrying permit. Our presentation will include tools, which we have developed to assist with explaining blast related phenomenon to both regulators and the public.

Jan 1, 2003

By Karl E. Burgher

Since World War II, the need for the use of explosives with testing, construction, demolition, mining and quarrying near urban areas has increased dramatically. Once remote, testing areas have been encroached upon by commercial and residential areas. Evidence has been found that overpressure levels near these areas can be estimated using meteorological conditions. This paper reviews a study where 205 test shots were fired, meteorological conditions recorded, and over-pressure levels estimated using multiple regression techniques.

Jan 1, 1988

By Dale Preece, Stephen Chung

Blasting induced rock fragmentation is an art that has been developed and refined for hundred’s of years through blasting and recording the results. Good blasting fragmentation practices were thus developed through experience. However, this method requires a history that is typically developed in a mine over a number of years and sometimes at considerable expense. Quantification of fragmentation as a function of rock-mass characteristics and blast design is attractive. Developments towards this end have included semi-empirical methods as well as computer codes that explicitly treat shock wave transmission and the subsequent rock breakage. This paper will present predictions of fragmentation resulting from rock blasting using the computer code AUTODYN and a new state-of-the-art material model for brittle rock and concrete.

Jan 1, 2003

By Tom Treleaven, Andrew Williams

The town of Greenwich, CT, an exclusive suburb of New York City awarded several contracts for the installation of sanitary sewer in the North Mianus section of town. The Valley Road section was the most challenging from a rock excavation standpoint. The cut was up to 14 ft (4.25m), with adjacent utilities [20 in. (500mm) water, 6 in. (150mm) water and 8 in. (200mm) gas] located to within 5 ft. (1.5m) of the proposed sewer trench. Rock types varied but were ultra metamorphic in nature, ranging from quartzites, granite gneiss and various types of migmatities.

Jan 1, 2004

By Ali Kahriman, Abdulkadir Karadogan, Deniz Adiquzel, Umit Ozer, Suat Bicer, Mehmet Aksoy

This paper presents the analysis and measurements of blast-induced ground vibrations during the construction of Istanbul Kagithane – Piyalepasa – Dolapdere – Dolmabahçe highway tunnels. These tunnels known as T1 and T2 are being constructed by a joint venture group. Within the scope of the study, the particle velocities and frequencies associated with 126 shots during the advancement of the tunnels were monitored and analyzed by vibration monitors at the test site. During the statistical analysis, three different predictor equations widely used in the literature were used to predict peak particle velocity (PPV) and the results and comparison of the predictor equations are presented in this paper. Finally, the particle velocities and frequency values of all blast events were evaluated according to USBM and German DIN 4150 Norms in order to determine the damage risks of the neighboring buildings and structures.

Jan 1, 2008

By Steve Dillingham

Today, a typical blaster is likely to wear many hats, including, but not limited to, supervisor, risk manager, safety coordinator, explosives engineer, communicator, as well as professional decision maker. Simply put, a blaster in the new millennium is an all encompassing blast site manager. As you know, accidents on the blast site can range from blast crew injuries to blasting incidents resulting from vibration, flyrock, misfires, etc. Not surprising, the incidents can quite often be traced back to direct preventable human action on the blast site. They can, however, frequently be avoided, if responsibly identified early and managed properly by an efficient blast site manager. Your company cannot afford to simply employ blasters; good blast site managers are necessary to produce the safest results possible.

Jan 1, 2001

By Donald Thompson, Jessie Bonner, Ileana Tibuleac

Predicting ground motion from complicated mining explosions is important for mines developing blasting programs in regions where vibrations must be kept below certain levels. Additionally, predicting ground motion from explosions in complex 3D media is important for source size estimation for nuclear treaty monitoring. Both problems have been addressed under the development of a new series of programs including: 1) Generalized Fourier Methods to generate synthetic seismograms (Green’s functions) in 3D media for a moment tensor source implementation and 2) MineSeis3D, a program that simulates seismograms for delay-fired mining explosions with a linear relationship between signals from small size individual shots. To test the programs, three-component seismic recordings of three production shots at an iron mine in northern Minnesota were compared to synthetic waveforms in 3D media. Comparison of the observed and synthetic waveforms shows promising results. The shape and arrival times of the normalized synthetic and observed waveforms are similar for most of the stations. The synthetic and observed waveform amplitude fit is best for the vertical components in the mean 3D model but not as promising for the transversal components. The observed effect of spall on the waveform spectra was weak in the case of fragmentation delay-fired mining explosions. Commercial applications of the code could provide data needed for designing explosions that do not exceed ground vibration requirements posed by the United States Department of Interior, Office of Surface Mining.

Jan 1, 2005

By Paul Kunze

When a new bridge was needed across the upper reaches of the Yellowstone River in Montana, removing the old concrete bridge piers became an environmental concern for the highway department engineers. The location is about fifty miles downstream from the north edge of Yellowstone Park. The determination was made by the federal and state agencies charged with protecting the resource, that the old piers had to go but the river bed had to remain unchanged. Concerns were expressed that removing the concrete presented the potential for environmental damage to this protected portion of the river. These concerns prompted the state to place stringent restrictions on the contractor in the way they carried out the demolition and disposal of the piers. The reinforced concrete masses had to be removed to an elevation at least fifteen feet below the river bed and every bit of concrete debris had to be removed from the river channel. Explosive removal was discouraged, but the only other options: saw cutting, mechanical or chemical breaking, were not viable.

Jan 1, 2014

By Seokbin Lim

In the design of explosives devices, an understanding of the behavior of explosively propelled matter is one of the most important steps in maximize the performance of these devices. For instance, an explosively driven metallic liner in LSCs (Linear Shaped Charges) creates its functional effect of penetration after a finite distance of travel (before collapse), thus the detailed study of the projection mechanism of the flat liner after detonation helps in the optimization of the design of LSCs. In a typical metallic flyer driven by explosive detonation, the detonation gas propels nearby matter including flat flyers. After a certain degree of expansion in the detonation gas, the flat flyer reaches its maximum velocity and slows down afterward. These typical behaviors are well investigated and numerically studied by many researchers. However, the rarefaction intrusion (detonation gas expansion) near the surface of the explosive charge creates significant deformation of the flat flyer , and produces U-shaped bending or deformation near the edge of the flyer during projection, creating unexpected behavior in explosive devices of interest. In this paper, a preliminary investigation of a localized Ushaped deformation of flat metallic flyers during projection is studied utilizing a theoretical approach and computational modeling facilitating an understanding of a general tendency of the deformation behavior.

Jan 1, 2010

By R. Frank Chiappetta

A new blasting technique has been developed by International Technologies, LLC. to eliminate subgrade drilling, lower ground vibrations, improve fragmentation and reduce explosive consumption. The new technique utilizes a uniquely designed borehole plug, with a bottom hole air deck and a predetermined stemming mass on top of the plug. This combination is referred to as the Power Deck?. Single holes and full scale tests were conducted by Blasting Analysis International, Inc. (BAI) to determine how the system works, the mechanisms behind its success and the best design parameters to use for the given rock conditions. Results have shown reduced or eliminated subgrade drilling, ground vibration reductions of up to 33%, reduced explosive consumption by 16 to 25%, and improved fragmentation by up to 25%. This paper summarizes the methodology, field test setups, analyzes procedures and results for one series of single hole and full-scale tests which were performed in a Pennsylvania, USA quarry.

Jan 1, 2004

By C Agreda

The Cushion Blasting Technique applied to solve the high risk case history represented by a 10,704 TM rock locate at 120 M from the hydroelectrical plants of 350 KV each, is described, analyzed and discussed. The generation and distribution of 700 KV produced by two hydroelectrical plants must not be interrupted by any reason, because the 26 district of the province of cajatambo, of the Lima department; would not have electrical power. The search of the best alternative and methodology, the drilling and blasting pattern calculations, charge design and loading, connections and initiations of the 50 blasts are described, analyzed and discussed. Finally, the excellent results from a technical, economical, enviromental and safety point of view of the 50 primary blasts are discussed and emphasized.

Jan 1, 2005

By Bruce Vandenberg, R. Frank Chiappetta, John Foley

Recent advances in solid-state, field portable, fast framing compact video camera systems and PC based frame capture hardware now allow blast imaging up to 1000 frames per second. Up to 4.1 seconds of data can be captured directly into the unit, downloaded to a PC or archived to a standard VCR without data compression. Since no film processing is involved, motion analysis can be performed instantly and on-site within a few minutes. This paper will describe the design features and applications of the MotionMeter system and compare these with the analogous aspects of film-based cameras and other systems. Of all blast monitoring systems and techniques available today, high-speed motion picture photography and videography still remain as the most valuable, stand alone, diagnostic techniques for troubleshooting and evaluating full scale blasts in the mining and explosives industries. High-speed image data, coupled with information obtained from other instrumentation systems, such as continuous velocity of detonation recorders, laser surveying systems, refraction and ground vibration recording seismographs, etc., can eliminate many assumptions about what actually took place in a blast. Thus, diagnostic confidence in evaluating both excellent and poorly designed blasts is increased, and optimum blast results, (which are application dependent), are achieved considerably faster when compared to the trial and error approach of relying on strictly the experience factor. Applications include developing site-specific blast designs, decay equations relating burden, burden velocity and explosive energy, determining ground response times, reducing coal damage, quantifying backbreak, evaluating the effectiveness of sternming, checking delay detonator firing times, evaluating air decks and for studying general dynamics. Motion analysis is performed with a 2D and 3D software package developed specifically for video analysis, but is also directly applicable to film analysis when using a digitizer. Dimensional controls, lens aberration, field set-ups and camera orientation are all automatically corrected for with matrix analysis.

Jan 1, 2000

By H Ulrich Leiste, Leslie Talor

This paper describes a series of small scale tests conducted to investigate the loading applied to a flat plate by the detonation of a cylindrical charge very close (between two and three charge radii from the center of the charge) to the structure. The testing used very small quantities of explosive (PETN): Two different series of tests were conducted. In the first test series, impulse loading on the target plate was investigated using three different sizes of charge. In the second series, pressure time profiles were determined. The charge size was 6 g or less. Impulse was found using high speed video of the target plate to determine its displacement as a function of time, from which initial plate velocity was obtained. Kolsky Bars, placed at the same distance from the charge as the target plate, were used to determine the free-field pressure time profile of the output of the charge at this distance. Two different types of target plates were used in the impulse study. One was just a plate while the other was a plate constrained with a steel frame.

Jan 1, 2009

By Bruce Vandenberg, Andy Bartfay-Szabo, Steve Conway

Recent advances in solid-state, field portable, fast framing video camera systems and PC based frame capture hardware now allow blast imaging up to 500 frames per second. Up to 8 seconds of data can be stored directly into the unit, downloaded to a PC or archived to a standard VCR without data compression. Since no film processing is involved, motion analysis can be performed instantly and on-site within a few minutes. This paper will describe the design features and applications of the SVClOOO system and compare these with the analogous aspects of film based cameras.

Jan 1, 1995

By Jason Ryan, Stephen Harria

Q.E.D. (QED) is a blast design and evaluation model that allows full three-dimensional design specification including the development of unique “live” terrains and an unlimited variety of complex charge configurations. QED’s analysis package allows the examination of likely outcomes resulting from changing various design variables in terms of vibration, fragmentation, rock-mass damage and muck-pile profile. Especially applicable to use cautious blasting applications, QED’s damage model uses vibration to estimate rock damage beyond excavation boundaries. This relates directly to operations such as Yucca Mountain Nuclear Waste Repository in Nevada, where damage beyond the excavation perimeter must be tightly controlled. The U.S. Department of Energy (DOE) h as b een studying a site at Yucca Mountain, NV to determine its suitability for long term storage of nuclear waste. The main mechanism of waste isolation will be the natural barrier of the host rock Total Systems Performance Assessment (ISPA) is used to model the excavation design and its behavior over time. Of importance to TSPA is quantifying the condition of the rock-mass before and after excavation. Ideally, there should be no excavation-induced changes to the rock-mass’ structure (removing the requirement to model the effects). At the least it may be possible to keep excavation-induced damage far enough away from waste packages so that modeling of these effects will not be required. QED can calculate a prediction of the extents of blast induced damage to the rock-mass. By using this metric as a design parameter, it may be possible to complete excavation of the repository more rapidly and inexpensively than previously thought, without jeopardizing the structural integrity of the waste containment areas or requiring blast damage to be modeled by the TSPA. This paper will explain the structure of the QED blast modeling system and show the analysis of historical data from Yucca Mountain. Processing of the historical data and the subsequent results will demonstrate how blast modeling can be used on an ongoing basis to assist the excavation process at Yucca Mountain.

Jan 1, 2000

By Mike Boissonneault

It was three years ago when the “storm of the century” had taken a firm grip over the Pacific West Coast and inland areas. At the Big Sky ski resort in Montana on Christmas morning two ski patrollers set out to perform an explosives “hand charge” avalanche control mission that would see only one return. It has been difficult to determine exactly what happened. Investigators do know that there were three separate and consecutive attempts to light a safety fuse, when it had apparently been burning since the first attempt. Time ran out after the third attempt. Although this accident has had a profound impact on North American avalanche control programs, I am sure it pales in contrast to the shock and grief experienced by family members who lost a loved one.

Jan 1, 2001

By Edward Walter

Rock excavation for tunneling projects occurs on a regular basis in the Cleveland area. These tunnels are being constructed to increase the capacity of the sanitary sewer system. Controlled blasting must be performed to remove rock in a number of phases of the project. The rock excavation for construction of a junction chamber is just one case where blasting is the safest and most efficient method available.

Jan 1, 2001

By Sam Kangwa, Thomson Sinkala

In the mining industry, drilling accuracy has a significant effect on the economy of operations. In this paper, results from the Nkana Division of the former Zambia Consolidated Copper Mines are presented. For the stope investigated, it was found that the extra operational costs alone were 462% of the planned costs! Clearly, there is more than good reason to pay attention to drilling of good quality holes.

Jan 1, 2004

By Charles Pretorius, Henk Ludik

Navachab Mine experiences difficulties with pit wall stability in certain areas of the mine. The main reason for the instability is the fact that the geology comprises many joints and faults. Blasting, without impacting negatively on the stability of the pit walls, poses a major challenge.

Jan 1, 2006