Search Documents

By M. Mirnezami

Pentlandite samples were obtained as Ni concentrate from three Canadian plants and one specimen sample from Ward?s Scientific Establishment. The samples were upgraded using gravity and magnetic separation techniques. Nickel concentration was determined by atomic absorption spectroscopy. Microprobe analysis identified a range in Co and Cu lattice substitutions. All samples exhibited similar zeta potential-pH trend with isoelectric points from 2 to 3, and similar responses to copper activation and addition of xanthate. The similar trends indicate that the variations in lattice substitution identified have no significant effect on electrokinetic properties; that is, samples from any source likely yield results that can be generalized.

Sep 1, 2012

By C. R. Mambote

Vanadium is an important metal that is used mainly in ferrous and non-ferrous alloys due to the high tensile strength, hardness, fatigue resistance and corrosion resistance. Vanadium consumption in the steel industry represents about 85% of the vanadium-bearing products produced worldwide. The primary sources of the metal are patronite, roscoelite, and mottramite. Vanadium has also been produced as a by-product of the uranium production program which uses carnotite ores as a source of uranium. Vanadiferous magnetite iron ores are used for producing vanadium as well. In addition, it is known that vanadium can be recovered from the ashes of crude oil and petroleum coke. The process for treating boiler residues, fly ash and petroleum coke is similar to the process used to treat spent catalysts and ores. However, some of these materials may contain high carbon that must be removed at specific stage of the operation. Several processes are available for obtaining vanadium from fly ash, such as roasting vanadium bearing materials in the presence of sodium salt. The salt roasted calcine is subsequently leached with an alkaline or acidic solution. To obtain a cal-cine from which the vanadium can subsequently be recovered, the carbon in the source materials has to be eliminated prior to the roasting process. Other processes use the conventional hydrometallurgical route, in which fly ash is leached with sulphuric acid to obtain an impure vanadium pentoxide. The impure vanadium pentoxide is then treated with a sodium carbonate solution under atmospheric conditions to subsequently precipitate vanadium as ammonium metavanadate. Actually, the salt roasting process is the only process used commercially. In the present study, the progress in the technology of vanadium extraction from secondary materials is reviewed. The perspectives and the challenges for new process development are discussed.

Jan 1, 2014

By Rodrigo Ladrón, Gonzalo Rund, Gonzalo Montes-Atenas

Modelling ore comminution processes have been a highly fruitful scientific topic. The models have been proved to be largely dependent on the selected comminution technology. Among them, semiautogenous (SAG) mill technology has been widespread implemented in plants but no complete understanding of the mechanisms involved in the process is available. Tracing back in history, SAG models considered only some granulometric cut sizes such as the t10 and attempted to relate these parameters with the energy involved in the impact between particles. Other models evolved towards incorporating physical properties of the material being ground and the mill operating conditions. These material properties have assisted to obtain a more comprehensive description of the breakage mechanisms; nevertheless, the gathering of all known parameters still have not delivered a model able to describe the process. This may be a result of emergent properties or phenomena originated from interactions inside the process which are hard to predict turning the size reduction operation into a complex system. Cellular automata provide one answer to describe complex systems by following simple rules. The aim of this research work is to establish the preliminary rules of thumbs enabling the implementation of cellular automata able to predict the particle size distribution at the exit of a SAG mill. The methodology involved developing a simple 2D model of a ROM sample. Plant data from two mine sites were correctly described by a set of three rules: two rules describing the particle reduction and one rule associated with material transport across the mill. Further analysis related with expanding this model to 3D and its impact on the liberation of valuable material is also discussed.

Jan 1, 2014

By Y. X. Yang

Bottom ash is a solid waste stream in a Waste-to-Energy (WTE) processing plant during the combustion of the municipal solid waste (MSW). In the Netherlands, bottom ash contains typically about 18% metals originated from the MSW, and current industrial practice could recover about 10% metals through magnetic and eddy current separators. The remaining 8% as the finer particles is difficult to recover through current physical separation technology. Among various alternatives, vitrification is one of the promising options to immobilize the ash and recover the remaining metals. During vitrification a homogeneous glassy slag and a Fe-Cu based alloy were obtained. In the cur-rent study, the metal alloy recovered from the bottom ash originated from a Dutch Waste-to-Energy plant contains about 82 wt% Fe, 12 wt% Cu and 6 wt% other alloying elements and impurities such as C, S, P, Ni etc. The generated alloy does not have direct commercial applications, and separation of copper from iron-based alloy is critical to obtain the market value of both copper and ferrous constituents. To find a suitable processing route of this metal alloy, various alternative approaches have been considered for an efficient removal of copper from the alloy, and the focus in the present study was on the sulphide treatment at elevated temperatures of 1400 ~ 1500oC. The tested sulphide systems include pure FeS, FeS containing sulphide mixture (such as Na2S and Al2S3), pyrite (FeS2) mineral, ZnS containing sludge as an industrial waste. It was found that the carbon saturation of the alloy is proved to be an essential condition for a proper phase separation. The results showed that FeS mixed with Na2S, ZnS containing sludge and pyrite are effective sulphide systems for copper removal with a removal efficiency of 92% by using pyrite and 95% by zinc sludge at a S/Cu ratio of around 7 times of the stoichiometry. The copper content drops from 12 wt% to about 2 wt%. However, it is still difficult to remove copper completely from the alloy in a single step, and a multi-step operation is needed. The present research is expected to contribute both to the utilization of the metal recovered from bottom ash, and to the general recycling of steel scrap where copper removal from the steel scrap is a critical issue.

Jan 1, 2014

By G. C. He

Effects of irregularity, rough surface and aggregation of fine particles on ultrasonic attenuation are significant. The effects should be considered while predicting particle size by ultrasonic attenuation technology. The scanning electron microscope micrographs analysis also shows that particles surface is rough and irregularity. Any slurries has its fractal structure and its special fractal scale and dimension, so, effects of irregularity, rough surface and aggregation of fine particles can be de-scribed by fractal model. The discrepancies between predictions of ultrasonic attenuation based on the assumption of smooth spherical particles and data obtained from slurries of irregular particles indicated that there were different fractal structures. The ultrasonic attenuation model was modified by fractal dimensions. The result of experimental data and analogue calculation indicated that pre-dictions of the fractal modification of ultrasonic attenuation model show good agreement with experimental data. On the other hand, from the values of fractal obtained by inversely calculation, the degree of effects of irregularity, rough surface and aggregation of particles can be estimated. The positive value of fractal dimension indicates that the aggregation has the dominant effect on ultra-sonic attenuation, otherwise, the irregularity and rough surface has the dominant effect.

Jan 1, 2014

By M. F. He

There are three polymorphic modifications in pyrrhotite (monoclinic, hexagonal and orthorhombic), with monoclinic and hexagonal polymorph being more abundant. The floatability of different crystalline structures of pyrrhotite (monoclinic and hexagonal) is studied in this paper. It is shown that the floatability difference of monoclinic and hexagonal is obvious and that the flotation recovery of monoclinic pyrrhotite is greater than that of hexagonal pyrrhotite using different collectors . Using butyl dithiophosphate as collector, the flotation recovery of pyrrhotite is higher than when sodium diethyl dithiocarbamate and sodium butyl xanthate are used as the collectors. Monoclinic and hexagonal pyrrhotites are more easily activated by Cu2+ in acidic conditions than in alkaline conditions, while Cu2+ can not activate hexagonal pyrrhotite when sodium diethyldithiocarbamate was used as the collector. By the measurement of contact angle, it is indicated that monoclinic and hex-agonal pyrrhotite float well and are easily activated by Cu2+when dithiophosphate was used as the collector. Using sodium diethyl dithiocarbamate as a collector, the flotation behavior of pyrrhotite was investigated. The relationship between potential and pH range for pyrrhotite flotation was established. The results show that the flotation of pyrrhotite is dependent on pulp potential at certain pH values.

Jan 1, 2014

By Ricardo Duque-Soto, Gonzalo Montes-Atenas

The depletion of water resources has posed an enormous challenge to the continuity of many mine sites, particularly those located in arid zones worldwide. In Chile, the use of seawater has been foreseen as one possibility to solve this problem. Nevertheless, the direct use of high ionic strength solutions such as those present in the sea has been found to have some drawbacks. Specifically, rhe extraction of copper from complex ores using high ionic strength solutions such as that of seawater has become one of the most relevant topics in the field of copper hydrometallurgy. This study aims to determine the effect of the degree of salinity on copper extraction kinetics in mixed oxide-sulfide ores. A leach protocol was implemented to study the extraction kinetics, varying the degree of salinity of the medium and the temperature. A thermodynamic model was developed to explain differences in the metal extraction. It was found that the ionic strength impacted positively the copper extraction, probably due to the reduction of the effective concentration in solution due to ionic interactions enhancing the diffusive mass transport of copper ions. This effect is observed to be enhanced when up to an overall salinity values close to 20gpl.

Jan 1, 2014

By Juan B. Yianatos

"After almost 100 years, since the first commercial application began in Australia, flotation has shown an extraordinary growth and nearly 2 billion tons of ore per year are presently treated by flotation processes. During this time flotation has promoted a wide scope of research activities ranging from fundamental chemistry and hydrodynamic studies to studies of industrial operations. In general, fundamental studies have been mainly related to ideal situations. In recent years, however, large efforts have been focusing on achieving a better insight into the actual sub-processes provided by the development of new and more sophisticated instrumentation. Since the massive incorporation of flotation columns, around 15 years ago, a renewed interest in flotation fundamental studies, process modelling and new cell designs have been observed worldwide. The key role of the froth has been recognized as an independent and sometimes rate limiting process step. Thus, separation of pulp and froth process stages seems the most appropriate in terms of process modelling, diagnostic, design and scale-up purposes.In relation to flotation equipment development, until the middle of the 1970?s, only the sub-aeration mechanical cells were dominant. Since the 1980?s, the use of pneumatic cells and forced air mechanical cells has emerged strongly. Also, in the last decade, flotation equipment has shown a dramatic increase in size, reaching values of 200m3 in unitary mechanical cells and more than 300m3 in columns. The general feeling, however, is that, despite the great advance observed in terms of process knowledge, the mechanisms and principles of industrial flotation cells design and scale-up are still not fully understood.Advances in process instrumentation and control now in use allow for more efficient operations, both in metallurgical performance and savings in operating costs.INTRODUCTIONFlotation is a widely used process within the minerals processing industry, as well as being used for water treatment and de-inking of recycled paper. Froth flotation started in Australia at the beginning of the 20th century and since then flotation technology has made significant advances. Flotation was firstly applied to sulfide ores. The largest tonnages treated by flotation are copper and copper/molybdenum ores, handling about 50% of the total ore processed. Also significant are phosphate, iron ore and coal treatments. At present, Chile is the foremost copper producer in the world with around 35% of the world?s production. Figure 1(a) shows the evolution of copper production in Chile over the last decade. The total amount of fine copper produced in year 2001 was 4.7 million tons, from which 3.2 million tons was processed by flotation while 1.5 million tons went through LIX-SX-EW processes, which also showed significant development during the same period (Anon, 2001). The total flotation treatment of copper ores in Chile is about 325 million tons per year (Anon, 2002), so the world treatment of copper ore by flotation can be estimated at about 1 billion tons per year. Consequently a total of nearly 2 billion tons of ore per year is presently processed worldwide by flotation (Fuerstenau, 2001). In order to handle the higher tonnage of low-grade ore, a worldwide trend towards the development and use of larger flotation machines began in the 1960?s. Figure 1(b) shows that the trend became extremely marked from the beginning of the 1990?s, which is consistent with the strong increase in copper production during the same period."

Jan 1, 2003

By Gökçe Törenli, Okay Tutar

"Predicting the performance of plant-scale comminution circuits is essential to monitor the energy use and product size distribution, allowing us to control and optimize the whole process. In the light of this issue, with the assist of recent technologies, simulation techniques utilize the chance of putting the theory into practice in the most accurate way. For this purpose, this study aims to evaluate and optimize the efficiency of a plant-scale ball mill circuit by using perfect-mixing ball mill model on a simulation environment. The comminution circuit is selected from a specific copper-ore processing plant in Turkey. The essential parameters which are required for this study such as fresh feed Bond work index, size distribution etc. are determined by laboratory experiments. The forecasted data which are calculated by third-party software will be compared by the industrial operating data, in order to determine the performance of comminution circuit. In addition to that, this methodology provides a greater ability to analyse, optimize and understand the comminution circuit of ore treatment plant. The authors believe this work will provide supplementary data for further studies on simulation and subsequent optimization of comminution circuits.INTRODUCTION By the assist of mathematical models of the grinding mills and classifiers, simulation of the grinding circuits become more common in comminution because it is relatively economical and able to consider many variables simultaneously. It’s proceeds depends on the accuracy of the models and capability of reflect real operations. Computer-based simulation studies would provide the quantified information about the effects of the proposed changes on the comminution circuit performance in terms of size distribution, mass flow rates, equipment efficiency etc. Then the mentioned data used in order to check the suitability of the current equipment to the modified conditions, and for equipment selection. The outputs of circuit could also be used to estimate downstream flotation circuit performance because the general aim in this study is to The aim of the study is to investigate optimum operating variables and achieve p(80) size of 57 µm and 64 % of -36 µm particle in hydrocyclone overflow stream, which is optimum for that porphyritic copper ore for best concentrate recovery after flotation process in specific copper ore comminution circuit by using modelling and simulation techniques. Sampling survey was carried on the fine ore bin in order to perform Bond work index test and determine work index value (Wi). Thereafter mass balancing, using the size distribution data and tonnages, models for ball mills and hydrocyclone were developed. Finally, the circuit performance were investigated by computer simulations via JKSimMet software."

Jan 1, 2018

By K. W. Stöckelhuber, A. Wenger, H. J. Schulze

"An important elementary step of the flotation process is the forming, drainage and rupture of a thin intervening liquid film between bubble and mineral particle.After the encounter of the bubble with the solid surface a wetting film is formed. The initial thinning of this film is driven by the capillary pressure inside the bubble. When the film has reached a certain thickness rupture can take place. There are two possible mechanisms describing this process:(a) Gas nucleation, caused by nano bubbles inside the film.(b) Growing fluctuation waves (spinodal dewetting) on fluid interfaces under the influence of any kind of attractive forces (electrostatic, van der Waals).Metastable wetting films on negatively charged, hydrophobic glass surfaces (gaseous phase methylated), or on hydrophilic, positively charged glass surfaces (with Al3+ ions), have been analysed by means of the kinetics of film thinning according to the Reynolds law. These experiments demonstrate that both mechanisms can be responsible for the rupture of a thin wetting film."

Jan 1, 2003

By Tom Liu

This paper is a fundamental study of bubble-particle collision efficiency in turbulent flows. A CFD-based microscale scheme for the prediction of turbulent bubble-particle collision efficiency in a 3D isotropic turbulent flow is developed, and in this way, turbulence effects on particle-bubble collision efficiency are taken into account for the first time. By comparing the computed results with experimental data from the literature, the CFD simulation is shown to correctly predict the bubble-particle collision efficiency in a quiescent environment. The CFD method was then applied to the investigation of bubble-particle collision efficiency in a turbulent flow, and the simulation results are shown to be qualitatively consistent with the real observations. The predicted collision efficiency can be used in a multiscale modelling scheme, which would account for all control variables in a flotation cell, such as impeller structure and tip speed, air nozzle structure and air flow rate This study indicates how microscale simulations of bubble and particle behaviours, coupled to macroscale CFD simulations of flotation cells, can provide a powerful tool predicting the flotation rate in a real flotation cell.

Jan 1, 2014

This paper discusses current workforce demand projections for mineral processing engineers and emerging trends in mineral processing education. Attempts are made to identify gaps that often result in a mismatch between skills taught and skills needed by the practicing engineer. Clear examples of this include a less than uniform training in chemical aspects of mineral processing, and an understanding of the statistical and experimental design tools necessary to tame the often-large variation in operational parameters and plant data. The end goal is an educational system modernized to prepare mineral processing specialists for productive careers in the sustainable development of natural resources. A framework for revamping education based on an integrated modular approach is also presented. Keywords: mineral education trends, mineral processing programs

Sep 1, 2012

By In-Kuk Bae, Kwang-suk You, Joobeom Seo, Kwanghyun Bea, Hyung-Seok Kim

Arsenic in base metal sulfide ores is highly penalized owing to high costs for its control in metallurgical processing. The arsenic element in the lead-zinc ore, which is target ore in this study, has been shown to be in the form of arsenopyrite. Experimental work in this study is about arsenic rejection flotation, using depressant suitable for the removal of arsenopyrite from the Pb concentrate. The arsenic rejection flotation also included the oxidation treatment of Pb concentrate with H2O2. In this study, the Pb concentrates containing 80.7% Pb and 0.25% as was obtained with the additions of aluminosulfate as arsenic depressant. And through IR measurement, it was also known that the addition of aluminosulfate during arsenic rejection flotation formed calcium aluminosulfate hydrates on the surface of arsenopyrite particle, resulting in rendering arsenopyrite hydrophilic.

Jan 1, 2014

By Vinay Jain, Dharmendr Kumar, Beena Rai, Venugopal Tammishetti

"Selective dispersion-flocculation is considered to be an effective process for the beneficiation of ultrafine particles. This process is based on the preferential adsorption of a flocculant on the mineral particles to be flocculated, leaving rest of the mineral suspended. It has been successfully implemented at plant scales for the beneficiation of ultrafine particles of iron ores, for which conventional methods such as gravity separation, magnetic separation and flotation do not work efficiently. However, the key element responsible for the success of any selective flocculation process is the appropriate choice of the flocculant used for achieving the desired selectivity. At our lab, we are working on design and development of such selective reagents for mineral processing applications, including the beneficiation of iron ore slimes, using a combined molecular modeling and experimental approach. In this study we have employed density functional theory (DFT) to calculate the interaction energies and explain the interaction mechanisms of chitosan with the main minerals present in iron ore slimes, namely, hematite [a-Fe2O3], goethite [a-FeO(OH)], gibbsite [a-Al(OH)3] and kaolinite [Al2Si2O5(OH)4]. The magnitudes of the computed interaction energies follow the trend: Hematite > Goethite > Gibbsite ~ Kaolinite Al-OH terminated > Kaolinite Si-O terminated Analysis of the optimized geometries and electronic structures reveals that the O & N atoms of chitosan molecule form coordinate bonds with surface Fe-atoms of hematite while only weak hydrogen bonds are formed in the case of goethite, gibbsite and kaolinite surfaces thus explaining reasons behind the stronger interactions with the hematite surface. The theoretical findings were validated by performing selective flocculation experiments using chitosan as a flocculant. The selective flocculation experimental results show that a final concentrate of ~60% Fe can be obtained from a feed containing 53.13% Fe with Fe recovery of 74%. The mineral estimation in the obtained concentrate indicated that hematite and goethite are recovered in concentrate while gibbsite and kaolinite are rejected in the tails. These observations were consistent with our theoretical findings. Our work highlights the promising role molecular modeling techniques such as DFT can play in the design and development of selective reagents for beneficiation of alumina-rich iron ore slimes."

Jan 1, 2018

By E. Pourjenaei, P. Ghobadi

High Pressure Grinding Roll (HPGR) is efficient equipment in comminution process. HPGR could be a good option for preparing ball mill feed at the first stage of grinding due to its high efficiency and low energy consumption. Closing with a screen, these mills are utilizing as one of the principle parts in mineral processing industries, especially for iron ores. Recently, HPGRs are working as primary mills at 4 developing lines in Gol-e-Gohar Iron Ore Processing Complex, Iran. Different mechanism of particle crushing in compare to the other tumbling mills makes the HPGR as certain equipment with its own particular controlling parameters. Hydraulic pressure, roller speed and level of material inside feeding hopper are the most important variables influencing grinding efficiency of the HPGR. To figure out how they impress the process and operation situation, different industrial tests were carried out and the best result (d80 about 8 mm for HPGR discharge) was achieved at 180-190 bar pressure (P), 300 rpm speed (S) and 50% of hopper level (L). It is worth noting that this finding has been observed through past pilot test too. We also used design expert method (DX7 software) to develop the best design and analysis the test results, as well. According to the mechanical restriction of HPGR and process limitation in the plant (based on the industrial results), we adjusted value of each parameter in a logical range. Therefore, 20 industrial tests were conducted, as DX7 recommended, and the various impacts of the parameters and their interaction were identified based on statistical analysis. As the authors expected, it was revealed that after presser, roller speed is a critical variable because of its significant role in residence time of the particles between the rollers. The function below has been determined to explain the relation between different parameters and the response.

Jan 1, 2018

By Jim Petrie, Mary Stewart, Damien Giurco

This paper describes a generic approach to analysing the environmental and economic performance of a global mineral/metal value chain, with the express view of improving the quality of prospective decision-making within the industry in order to ensure more sustainable outcomes. The starting point for this analysis is the development of a global stocks flows and transformations model, for the metal of interest. Any aspect of the value chain, e.g. “metals refining, “goods manufacture”, “use and disposal”, can be assessed, either relative to other stages in the value chain, or in more detail by focusing on the technologies used within that stage. The use of this model as a decision support tool is explored here for the case of copper. Both primary and secondary production routes are enumerated, covering a range of processes, for seven distinct geographic regions round the globe. The value of the modelling approach is explored for different energy mixes. In particular, the case study examines the impact of increased recycling on the (re) distribution of global and regional environmental impacts for technologies-in-place in these different regions.

Jan 1, 2003

By P. K. Sen, Mrinal K. Ghose

Tailing slurry is usually abrasive and possesses high viscosity. This paper examines the existing iron ore beneficiation process and focuses on some of the key environmental issues related to the disposal of tailings. It identifies that almost 32% of the iron ore extracted ends up as tailings and they are usually disposed in slurry form in tailing ponds. By the year 2000, 27 Mt of iron ore tailings were generated in India, which has become one of the biggest waste handling problems to the industry. Characteristics of the tailings vary widely. So the physical nature of tailings cannot be considered separately in isolation without considering the mill effluent from the beneficiation plant. In the present investigation, studies were carried out in three iron ore mines in India to evaluate the characteristics of tailings from the beneficiation plant. The tailing samples were collected from different locations during a time period of one year and analyzed. The results will be discussed and the characteristics of the tailings have been evaluated. The disposal system of tailings at the three mines was evaluated. The research on the settling characteristics of tailings indicates that the area provided in the existing tailing ponds in India is much more than that of the experimental results. This paper concludes that sedimentation tests are essential to design appropriate tailings pond with respect to size. In the proposed scheme it is suggested that an additional unit process, i.e. sedimentation tank be added to the process before the disposal of tailings to the tailing pond.

Jan 1, 2003

By C. Çelik

Nowadays the optical sorting of industrial minerals is one of the most important processing methods which has cost efficient production possibilities. This method is used for industrial and raw materials that have different colour and brightness features. Initially this technology is used for sorting of foodstuffs and recovered glass, but for a long time also as physical mineral processing method for both industrial minerals like: limestone, marble, talc, basalt, flint, quartz and secondary raw materials like: building rubble, refractory materials, glass, plastic and household waste. In this study via optical sorting the separation of quartz out of a flint mix, which consists of the particles with different colors and brightness, is aimed. Experiments are performed on an optical sorting machine named CombiSense® 1200 at the institute of ?Aufbereitung mineralischer Rohs-toffe? RWTH Aachen. This automatic picking device was developed by the company ?Separation Systems Engineering (SSE), Wedel?. Hand picking method is used for product analysis and the efficiency tables are prepared on every step accordingly. This process enables to reach quartz products with purity up to 100%.

Jan 1, 2014

By Z. M. Dai

Microorganisms in AMD (Acid Mine Drainage) were enriched in 9K culture medium. The enrichment was applied to leach copper pyrite after the microbial community structure and metabolism was stable. Before and after bioleaching, the microbial DNA was extracted and applied to RFLP (restricted fragment length polymorphism) analysis to demonstrate the relationship between the leaching efficiency and the change of microbial community. Atomic absorption spectrometry results showed that when concentration of the pulp was 10% and pH were 1.5, 2.0 and 2.5, the leaching rate were 56%, 57% and 34% on the 18th day respectively. These results indicated that the rise of pH resulted in the decrease of leaching rate. In lower pH condition, the growth of microbe was faster: when pH was 1.5, the microbial cell number reached to 1.4×107cells/mL on the 9th day; while pH was 2.5, the microbial cell number decreased to 4×106cells/mL. The analysis of microbial community structure showed that Acidithiobacillus ferrooxidans and Leptospirillum ferrooxidans were dominant species before bioleaching (account for 43% and 32% respectively). And after bioleaching, these two species were still dominant when the initial bioleaching pH were1.5 and 2.0. While the initial bioleaching pH was 2.5, the proportion of these two species decreased. These results demonstrated that the initial bioleaching pH would affect the microbial community structure in bioleaching system at room temperature, and this affect could lead to different copper pyrites bioleaching efficiency.

Jan 1, 2014

By O. A. Bascur

"In recent years, metal producing companies have increased their investment in automation and technological innovation, embracing new opportunities to enable transformational change. Internet of Things (IoT) is one of many transformational initiatives, which can fundamentally revolutionize how industrial complexes operate. Whatever the issue, the answer is in the abundant and growing quantity of real time data and events collected in the grinding and flotation circuits in a mineral processing plant. Based on earlier work, today a grade recovery model permits identifying the best operating conditions in real time. We will review the strategy for increasing the value of the abundance instrumentation in current plants. An optimal Gaudin size distribution model provides augmented information from traditional sensors to find the optimal grind cut to reduce metal losses in the flotation circuits. The large amount of sensors in a flotation circuits permits to estimate the recovery and to find the optimal froth depth and aeration using an air holdup flotation model. The paper will describe the strategy of classifying data for on line generation of insights to using operational intelligence tools. We will discuss the implementation Recovery/Grind strategy with industrial examples in non-ferrous mineral processing and iron beneficiation.INTRODUCTIONThe declining supplies of high grade ores and increasing consumption of mineral and metal products have demanded higher operational efficiencies with minimum capital investments. The objective of copper flotation objectives are based on maximizing the dollars return on the concentrate produced. The economic efficiency is maximized by manipulating the circuit along the grade/recovery curve relationship. To achieve such objective improved stabilization of the grinding and flotation circuits are required (Oosthuizen, Craig, and Jamsa-Jounela, 2017)."

Jan 1, 2018