Search Documents

By S. A. Kondratyev

"The present research work aims at disclosing the dependence of flotation concentrate recovery and its grade on the physically adsorbed collecting reagent properties, viz., surface pressure in the reagent film at gas-liquid interface, velocity of reagent species spreading over the said interface, relation between interaction energies of collector molecules within a film and with water dipoles.When using a single collecting reagent it is possible to improve the flotation concentrate grade in two ways, namely, by reducing collector consumption rate or using a weaker reagent. According to the proposed mechanism, a decrease in the physically sorbed species of the collector leads to a decrease in the rate of removal of the kinetic restriction of a flotation contact formation. As a result, the recovery of the useful component is reduced and the content of valuable components in the flotation concentrate is increased. The relationship between the spreading velocity of physically sorbed species at the gas-liquid interface and the recovery and quality of the flotation concentrate has been experimentally proved. Reduction in collector consumption lowered the valuable component recovery at a higher grade of the concentrate.The reasons were established for a rise of valuable content in the flotation concentrate if a weaker collector was used. It is justified that the use of a weaker collecting reagent with a shorter hydrocarbon fragment declines physically sorbed species of collector. The spreading velocity of collector derivatives at gas-liquid interface tends to lower along with less participation physically sorbed species of collector in formation of a flotation aggregate. The spreading velocity is determined for products of interaction between butyl-and ethyl-xanthates and lead nitrate at gas-liquid interface. It is found that the spreading velocity of butyl-xanthate derivatives is higher than that of ethylxanthate derivatives.The research work gets insight into the nature of relation between useful component content in the flotation concentrate and the useful component recovery. It is pointed out that adjusting the collecting activity of a collector makes it possible to influence a useful component content in the froth product thus gaining a compromise between wanted grade and recovery parameters."

Jan 1, 2018

By M. E. Holuszko

This paper reports the results of induction time measurements carried out on the products of film flotation of galena and sphalerite particles from three different size fractions (38~75µm; 75~150µm; 150~212µm). As expected, the tailings (sinking fraction) from film flotation at any particular surface tension, had always longer induction times than the concentrates (floating fraction), for both minerals. The difference between the induction times of film flotation concentrate and tailings could be as little as 2.5 ms and 5 ms, and as large as 6 ms and 10 ms. These differences can be related to the different hydrophobic characteristics of these fractions, as expressed by (?c) and composition of the particular film flotation product. In addition, the induction times of the larger particle size fraction were shown to be longer than for the corresponding smaller particle size fraction, even though the average ?c(degree of hydro-phobicity) of these fractions appears to be very similar. Desliming, Cu activation and collector addition to the sphalerite samples was shown to decrease the induction time values significantly.

Jan 1, 2014

By Wei Zhang, Jinhong Zhang

"In froth flotation, the adsorption of collector on mineral surface is critical for a successful flotation process. In present work, an atomic force microscopy (AFM) has been applied to study the adsorption of potassium amyl xanthate (PAX) on copper sulfides, i.e., chalcopyrite, chalcocite and bornite. The in-situ collected AFM images show that PAX adsorbs on chalcopyrite mainly in the form of oily dixanthogen; while it strongly adsorbs on chalcocite and bornite in the form of insoluble metal xanthate, which binds strongly with the mineral surface. The information obtained from the AFM study shed lights on the collectivity and therefore the selection of specific collector for different copper sulfide minerals in industrial practice.INTRODUCTIONFroth flotation, which treats the highest throughput in mining industry and produces the maximum economic outcome of any surface chemistry process, has been widely applied for the concentration of copper sulfide minerals, i.e., chalcopyrite, chalcocite and bornite. In flotation, collectors are added into the pulp (mixture of water and fine-grained minerals) to selectively adsorb onto the target mineral and render its surface with high hydrophobicity, which is generally beneficial for a strong mineral-bubble attachment and thus a high flotation recovery. Therefore, the adsorption of collector on mineral surface is vital for a successful flotation process and it has been studied by applying various surface analysis techniques, such as IR (Infrared Spectroscopy), CV (Cyclic Voltammetry) and XPS (X-ray Photoelectron Spectroscopy). (Poling, 1963; Allison et al., 1972; Mielczarski et al., 1984; Leppinen et al., 1989; Kartio et al., 1996) These studies have revealed a lot of information, such as the reaction, product and mechanism, of the adsorption of chemicals on mineral surface. It is also of great interest to directly get the image of adsorbed collectors on mineral surface changing with pulp chemistry, such as pH, redox potential, ionic strength and chemical’s dosage."

Jan 1, 2018

By M. Kanuchová, J. Briancin, M. Achimovicová

"Faculty of Mining, Ecology, Process Control and Geotechnology, Technical University, Košice, Slovakia An industrial eccentric vibratory mill was used for direct and short-time mechanochemical reduction of ilmenite concentrate (FeTiO3) and anatase (TiO2) with magnesium metal powder in order to reduce Fe and Ti resp. and hereby to convert them to the more soluble phases suitable for further hydrometallurgical processing. X-ray diffraction analysis of FeTiO3 after 60 min of milling with Mg confirmed the presence of Fe0 and Mg2TiO4 phases and for TiO2 after 180 min of milling the new TiO and MgO phases have appeared. X-ray photoelectron spectroscopy has detected Fe0 (metal) and Mg2+ species which are corresponding to the product of FeTiO3 mechanochemical reduction. The product of TiO2 mechanochemical reduction has revealed XPS spectral lines corresponding to Ti2+, Ti4+ and Mg2+ species on its surface. Morphology of mechanochemically reduced samples was studied by scanning electron microscopy analysis. Subsequent leaching of mechanochemically reduced FeTiO3 and TiO2 was performed in dilute HCl and H2SO4 at 80oC and compared with mechanically activated samples. The recovery of Ti has reached 100% for FeTiO3 and 79% for TiO2 after 60 min of leaching. Based on this study the flowsheet for possible processing of natural refractory titanium ores patented by author was adapted and documented. INTRODUCTION Ilmenite (FeTiO3), along with rutile (TiO2) represents the most important titanium resource necessary for titanium industry, for production of titanium metal, alloys and pigment grade TiO2 which are becoming more important and versatile for various industries such as an aircraft and aerospace, navy, chemical, automotive, medical and offshore wind industries, for machine and plant engineering and architecture as well, mainly due to high corrosion resistance. Pigment grade TiO2 is utilizing in pigment, plastic, glass, paper and rubber industries (Zhang, 2011). There are obvious research efforts for development of the potential alternatives to the expensive thermo-chemical commercial processes of titanium raw materials processing. Zhang (2011) has summarized conventional thermo- a electrochemical processes which involved a combination of pyrometallurgical, hydrometallurgical and electrometallurgical technologies and highlighted the improved hydrometallurgical routes promising for commercial application in the future. Such improvement could also be mechanical activation of FeTiO3, TiO2 by high-energy milling which causes their structural disordering, the changes of physical and chemical properties, consequently and has a positive effect on the dissolution kinetics (Achimovicová et al., 2014a, 2017, Baláž, 2008). The various types of mills such as a planetary ball mill, a vertical ball mill, a drum mill, an attritor were used for mechanical activation of FeTiO3 as a pretreatment process for subsequent leaching (Achimovicová et al., 2014)."

Jan 1, 2018

By S. Castro

Molybdenite flotation is strongly depressed at pH higher than 9.5 in the flotation of Cu-Mo ores in sea water. Chemically sea water contains mainly Na+ and Cl- ions, but also some secondary ions, such as SO42-, Mg2+; Ca2+, HCO3-; etc., which are not necessarily indifferent for the flotation of molybdenite. The natural floatability of molybdenite in sea water and in NaCl solutions containing different secondary ions is investigated by micro-flotation tests. The tests indicate that the floatability of molybdenite in alkaline media in 0.6 M NaCl solutions is not affected by the presence of anions, such as, SO42- and HCO3-, at concentrations similar to those occurring in sea water. However, a strong depression of molybdenite at pH ranging from 9.5-10.0, is produced by the alkaline earth metal cations (Ca2+ and Mg2+ ions), dissolved in distilled water or in 0.6M NaCl solutions. It was found that effect of Mg2+ions is significantly stronger than Ca2+ ions. Effect of both ions is attributed to hydrolysis and adsorption of MOH+ hydroxy-complexes. This is followed by subsequent precipitation of hydrophilic colloidal hydroxides at the molybdenite/solution interface, and in bulk solution.

Sep 1, 2012

By Juan Estrada, Mirtha Frómeta, Rubén Alcalá, Emilio Montejo, José Castellanos, Juan Berto, María Rivas

"The oxidized nickel ores from San Felipe deposit are composed mainly Smectites which gives to the pulps very unfavorable rheological .properties (cinematic viscosity and high shearing strength) for transportation processes (pumping), very low settling velocities and very low thickened pulps. These properties do not allow the preparation of high % solids, which affects the economic efficiency if a high pressure acid leach (HPAL) process is used. Pulps of close to 30% solids have very high BYS making pumping impossible. CIPIMM developed three technologies to solve these problems and to substantially increase the % solids in the pulps to be leached without a thickening step. These technologies are: • CIPIMM 2. At Preparation of pulps using additives. This method is based on the effect of some additives (inorganic salts) to improve the pulp’s properties. The use of this method allows increasing the % solids in the pulp up to 40% with good rheological properties • CIPIMM 2B. Preparation of pulps by thermal treatment of the ore previous to the preparation of the pulps. This method is based on the thermal destruction of the clays structure. Its use allows to obtain pulps with 50 - 60 % solids with excellent rheological characteristics. As a collateral effect, the Ni and Co grades increases by 10 - 15%. • CIPIMM 2C. Pulp preparation by chemical treatment. This method is based on the chemical transformation of clays, to obtain without thickening, pulps with 43- 45% solids and excellent rheological properties. The use of one of the three technologies depends on the chemical and mineralogical composition of the ores and the results of technical-economical evaluations to determine which one is the best alternative before running higher scale tests."

Jan 1, 2014

By V. A. Ivanova

Modification of hydrophobic part of carboxylic collector molecule is an upcoming trend for producing new reagents and changing its flotation properties such as activity, selectivity, sensitivity to hardness salts that inevitably present in the pulp liquid phase in the processing of ores containing calcium minerals. A wide range of apatite collectors ? monoalkyl ethers and monoalkylamides of dicarboxylic acids ? succinic, o-phthalic and maleinic acids have been synthesized by the addition of aliphatic alcohols and amines with various hydrocarbon radical value (from ?11 to ?16) to anhydride of the corresponding acid. Using computer modeling based on ChemBio 3D program of specialized complex Chem?ffice the calculation was carried out of charge distribution on atoms, energy parameters of molecules for investigated compounds. Calculated values of absolute hardness (?=6.75 ? 12.36) and absolute electronegativity (?= 5.67 ? 8.90) of the reagents showed that monoderivatives of dicarboxylic acids refer to the ?hard? type of bases. The degree of a charge transfer during calcium compounds formation of considered collecting agents (?N=0.009 ? 0.143) has been computed. Dissociations, micelle formation in solutions of these reagents and its hydrophobic and collecting properties were investigated in respect to apatite. Dependence of bulk, surface and collector properties on collector molecule architecture (double bond or benzene ring and non-ionogenic functional group in the structure of hydrocarbon radical) has been established. It is shown that experimentally determined dissociation constants (??a=5.16 ? 5.60 for succinic acid derivatives and ??a=3.32-3.78 for maleinic and o-phthalic acid derivatives) perfectly correspond to acidic properties predicted by computer calculations. Compounds of monoalkylderivative dicarboxilic acid have been determined optimum in composition and structure. The results of apatite flotation from apatite-nepheline ores of the Khibiny deposit (the Kola Peninsula) are presented here and show benefits of selected reagents. Keywords: monoalkylderivatives, dicarboxylic acids, reagents, microflotation

Sep 1, 2012

By A. P. Wang

Porous carbon adsorbents derived from inorganic materials templates such as zeolite and mesoporous silicate attracted considerable attention in the last decade and got great progress in re-cent years. However, so far almost all of templates used in the process were artificial porous materials; the porous carbons prepared by this method are very costly, which restricts the synthesis and application of templated porous carbons. In order to reduce the cost of templated porous carbons, natural inorganic porous minerals have been taken into consideration, which maybe possible and promising templates to prepare carbon adsorbents. In this work, we describe template process using tubular halloysite, rich mesoporous zeolite and low bulk density diatomite, as exemplars of the categories of inorganic porous templates which we have studied and discussed the effects of different templating structure on the resultant carbons. Two main carbon precursors, sucrose and furfuryl alcohol, were used respectively. The morphology of minerals and corresponding templated carbons were characterized using electron microscopy. The pore structures of minerals and templated carbons were characterised with nitrogen adsorption. The results showed that the morphology and pore structure of porous carbons are in good pertinence to those of corresponding templates. The morphology and pore structure of templated carbons could reflect those of corresponding templates at nanometer level. The templated carbons with high specific surface areas and rich mesopores can be prepared by using these three kinds of natural porous minerals as templates. The higher the surface area and pore volume of the minerals, the higher those of the corresponding carbons. The template carbons from halloysite possessed higher pore volume and mesoporosities. Based on the large mounts of experiment results, a model for the mechanism of resultant nanopores formation has been proposed. The nanopores of templated carbons are mainly composed of three kinds of pores: templated pores formed by removing mineral, hereditary pores formed by inheriting the pores of templates and nanopores formed during carbonization. These three kinds of pores have a close relationship with corresponding template.

Jan 1, 2014

The Sydvaranger magnetite mine was shut down in 1996 due to low iron ore prices. It was reopened in 2009. The flowsheet has remained more or less as in the old plant, based upon two grinding steps followed by magnetic separation. The Sydvaranger magnetite is free of harmful elements and should therefore be sold on the high quality market. This requires a concentrate containing less than 2 % SiO2. In the old plant, this grade was achieved by amine flotation. Amine was preferred as collector because it could be used in process water from the sea. The use of amine has been restricted by the Norwegian pollution authorities during the time the mine was shut down. Test work to replace cationic with anionic flotation is therefore done. Research on activation of quartz with Ca or Mg ions prior to anionic flotation was shown by basic research in the period from 1960 to 1980 to be effective under simplified laboratory conditions. This old research has now been followed up from a practical/empirical point of view. The basic work was mainly done on quartz and iron minerals only. In this case, an actual feed containing a number of minerals common in iron ores is used, in order to demonstrate that a commercial process is possible. Calcium activation is shown to work excellently but requires too high pH to be environmentally and economically attractive. Magnesium activation is a more difficult process, because the maximum concentration of MgOH+, which was shown to be the activator, is about 100 times lower than the alternative CaOH+. Flotation success depends partly upon the ore, some amphibole minerals are more difficult to float than pure quartz. Ordinary batch flotation test work is time consuming. A South African microflotation test cell has shown promise, because work can be focused upon flotation of the more critical coarser fractions of the Sydvaranger ore. Keywords: iron ore concentration, anionic flotation, mineral activation, microflotation, Sydvaranger

Sep 1, 2012

By E. V. Bratygin, E. G. Dmitrieva

The aim of the research was to study the thermodynamic characteristics of high-temperature processing of ilmenite concentrate deposits "Central" in a neutral and oxidizing atmosphere, as well as its interaction with alkaline additives. The research was conducted using a scanning colonoscopy on thermogravimetrical analyzer NETZSCH STA 449 F3. A sample of the test material weighing 10 mg was placed in a crucible and heated at a rate of 10 °C/min to 1200 °C in argon or air. Studies have been conducted pure ilmenite concentrate and its mixtures with 5 % and 12.5% of sodium carbonate. The results of the analysis of the thermogravimetric curves it was found that the recovery of the concentrate carbon will come from ulvospinel, not pseudobrookite, and the reaction recovery is possible at temperatures above 900°C. While removing produced in the decay ilmenorutile of iron oxides in an inactive form, for example, iron (III) oxide, it is possible to reduce the quantity of the solution of ilmenite formed during the restoration of the melt anosovite. The analysis of data obtained during heating of ilmenite concentrate with sodium carbonate in concentrations of 5 and 12.5% transition pseudobrookite in ulvospinel is missing, it just breaks down into hematite and titanium oxide, which, in turn, react with N?2??3. It should be noted that increasing the concentration of sodium carbonate in the sample contributes to more complete interaction of iron oxides and N?2??3 with formation of ferrites of sodium. This can ensure full recovery of iron oxides in the concentrate, which is part of secondary ilmenite can not be dissolved in the melt formed by the lower oxides of titanium. In addition, the increase in the content of soda in the mixture significantly reduces the temperature of the initial melting point of the slag and facilitates the coagulation of metallic iron.The obtained results were used for laboratory studies of the solid-phase sintering of briquettes from ilmenite concentrate with additives of sodium carbonate and a reducing – coal, as well as for the development of technological mode of solid-phase sintering of the concentrate with the aim of obtaining product recovery with a titanium dioxide content of more than 75 %.

Jan 1, 2018

By Leopoldo Gutierrez

Eight oil sand ores with the bitumen content ranging between 3.6 and 15 wt.% and the fines content (-44 micrometers size fraction) between 9 and 69 vol.% were subjected to the standard alkali extraction test used to measure the degree of oxidation of metallurgical coals. The results showed that there is a strong correlation between the absorbance of extracted solutions at a wavelength of 520 nm and the ratio of the fines content to the bitumen content. The latter factor is directly relevant to assessing the extractability of bitumen from oil sand ores. Bitumen extraction tests showed that the bitumen recovery decreased from 90 % to 30 % when the absorbance at 520 nm increased from 0.23 to 0.64. A comparison of the UV/visible spectra of solutions obtained from the alkali extraction tests with solutions of Aldrich Humic Acids suggest that low bitumen/high fines oil sand ores release substantial amounts of organic matter very similar, if not identical, to humic acids. In contrast, high-bitumen and low-fines ores do not release as much of the organic matter, and UV spectra of these leached substances are quite different from those of humic acids. Overall, the results show that chemical composition of bitumen in the tested ores varies greatly with ore type and oxidation, and that the alkali extraction test is a promising technique to quickly assess the extractability of bitumen from a given ore type.

Sep 1, 2012

By Girolamo Belardi, Silvia Serranti, Giuseppe Bonifazi, Roberta Palmieri

Ore textural and structural characterizations play a fundamental role in any preliminary study (i.e. comminution, classification, separation) addressed to the design and set up of beneficiation flow sheets. The possibility to utilise automatic tools able to perform a classification, and a quantitative description, of the mineralogical and petrographical characteristics of raw ore samples thus represents an important step to define, to control and to verify the entire set of parameters, ore-texture-related, that can affect the final beneficiation results. The procedure usually adopted is based on the analysis of polished sections and more in details the recognition of the different mineralogical species and associations and the measurements of some quantitative parameters estimating both the geometrical characteristics of each species and the possible spatial relationships between them. This approach, originally carried out by experts, utilising optical and/or electronic microscopy, was ‚replaced? during the years by more and more sophisticated devices integrating analytical facilities and acquired data processing. Such integrated analytical devices formed the breakthrough platforms into what is now known as modern Process Mineralogy. In this paper the possibilities offered by chemical imaging based devices and techniques, to perform ore minerals recognition/classification, and to perform their topological assessment, are presented. Tests have been carried out and are discussed in order to analyze the problems related to the development of suitable and low cost strategies addressed: i) to realize a full mapping of ore minerals/gangue inside selected samples, ii) to define the optimal data-flow handling to optimize the speed of processing versus the quality of the results and iii) to start to define logics and procedures finalized to implement innovative smart detection engines, chemical imaging based, for mineral processing addressed to perform both a preliminary characterization of the ore, at laboratory scale, and a further possible control of the different processed minerals flow streams.

Jan 1, 2014

By Yury V. Kulikov, Rakan Rahbani, Arkady Y. Senchenko

"The relevancy of complex minerals treatment is constantly increasing taking into account mineral resources depletion. Different refractory ores and concentrates, oxidized and polymetallic ores, as well as metallurgical products (slags) can be assigned to such mineral type. The treatment of such products via conventional flowsheets requires considerable capital and operational costs and does not always provide high recovery level of valuable components into a saleable product. Therefore, considerable amount of ores and metallurgical products are not treated, or treated inefficiently. One of the most promising approaches that allows economic treatment of refractory products is their ultrafine grinding down to 5-20 µm with subsequent processing or hydrometallurgy. Horizontal bead mills - the IsaMillTM, developed by Xstrata Technology, received their wide application in mining industry. Standard testing is performed under laboratory conditions in an M4 IsaMillTM (volume - 4 liters) to define the parameters of fine grinding. This mill completely simulates the operation of full scale industrial mills up to 50 m3 in volume (up to 8000 kW motor). The paper describes fine grinding technology performed in bead mills, and the importance of testing according to a certified method for industrial equipment selection. The paper contains description of promising directions of fine grinding technology application for several projects in Russia and Kazakhstan."

Jan 1, 2014

By Rolf Lauten, Yongjun Peng, Yufan Mu

"Biopolymers, produced from cellulosic biomass, have promising prospects of application as depressants in mineral processing. In this study, three different types of biopolymers (i.e., DP-1775, DP-1777 and DP-1778) were used to study the effect of polymer structure on flotation of un-activated pyrite, copper activated pyrite and chalcopyrite. It was found that the depressing effect of DP-1775 and DP-1778 was much stronger than that of DP-1777, and pyrite was depressed to a greater content than chalcopyrite with the same biopolymer at the same dosage. The biopolymer concentration played a vital role in determining the degree of depression. For each biopolymer, the higher the concentration, the greater the minerals were depressed. The mechanism underpinning the depressing effect of these biopolymers was explored in this paper. The concentration of biopolymers could determine the properties of the adsorption layer and the confirmation of biopolymer chains on mineral surfaces. The biopolymer molecules may aggregate when polymer concentration was over a critical value. Molecular weight and functional groups of biopolymers were the key factors characterizing the depressing capability of different biopolymers. Differences between the tested biopolymers and features of the adsorbed layer might account for the observed trends in ability to depress pyrite and chalcopyrite flotation. The greater depressing effect of biopolymers on pyrite over chalcopyrite might result from the preferential adsorption of biopolymers on pyrite over chalcopyrite."

Jan 1, 2014

By Luis Bergh, Juan Yianatos, Luis Vinnett

"Process automation as an engineering discipline is more than control systems since it includes industrial instrumentation, such as sensors, transmitters and actuators, as well as control and supervision systems, collection and transmission of data and real-time software applications to supervise and control the operation of plants or industrial processes. In the last several decades, accelerated technological development has provided a variety of software and hardware tools to aid development, maintenance and continuous improvement of automated systems. These developments however seldom reach their full potential in real plants. There are many factors to be considered, among them human capital specific training and the organization model. In this paper, a methodology for training engineers in advanced control and supervision of flotation plants is presented based on study of the application of these technologies in hybrid pilot plants. Since experimentation in real plants may present undesirable risks and costs, and simulation studies are usually limited to some unrealistic conditions, a laboratory where on-line measurements of the hydrodynamic behaviour of a pilot plant is mixed with phenomenological models has been created. In this form, an environment as close as possible to a real plant can be recreated. A flotation column and a circuit of three pneumatic cells are fully instrumented and connected to a PLC and PC network. In the control room, students learn applications of classical PID control in a DCS environment, advanced predictive control, on-line process operation diagnosis, fault analysis, virtual sensors and expert-fuzzy systems. Several undergraduate and graduate courses and theses are supported by this Process Control Laboratory infrastructure. Examples of these applications are discussed."

Jan 1, 2014

By Dave Deglon

The Western Cape Mineral Processing Facility (WCMPF) is a collaborative educational initiative between the Departments of Chemical Engineering of the University of Cape Town, the University of Stellenbosch and the Cape Technikon. The WCMPF was established in 1989 with the aim of improving mineral processing education in the Western Cape. Since its inception the WCMPF has had a number of successes in this area, especially in improving the quality of mineral processing practical training. In addition, the WCMPF has played an important role in promoting liaison and interaction between tertiary educational institutions teaching mineral processing in the Western Cape. Over the past decade the WCMPF has played a key role in the education of over five hundred mineral processing graduates and diplomates. This paper presents an overview of the activities of the WCMPF and attempts to encapsulate the ‘lessons learned’ from over a decade of successful functioning as a collaborative educational initiative in mineral processing.

Jan 1, 2003

By Emile Scheepers, Chris Aldrich, Jacques J. Eksteen

The pneumatic injection of CaC2 powder into molten iron has become a very reliable and effective way to carry out desulphurisation. The key variables that influence the kinetics of this process are the condition and composition of the top slag, the oxygen activity in the hot metal and the injection conditions. Notable injection parameters include carrier gas flowrate, reagent flowrate, lance depth and initial sulphur concentration. A one-dimensional, steady-state model for momentum, heat- and mass transfer in rising gasliquid- powder plumes was developed for conditions relevant to the CaC2 refining process at Saldanha Steel?, South Africa. Combined with a model that predicts the contribution of the topslag to the process, the overall rate of desulphurisation as a function of time was determined, thereby quantitatively demonstrating the influence of the above-mentioned injection parameters on the kinetics of the desulphurisation process.

Jan 1, 2003

In looking to the future of mineral processing the focus is typically on improved processing units. Basically it is a search for an elusive wonder machine that could revolutionise the economy of mining: the sorter that strips 50% of the ore with only a few % loss of value; the comminution device that uses 5% of the energy while producing fully liberated particles; or the recovery device capable of producing a 99% recovery at 99% grade. These aspirations are propounded against a reality backdrop of sorters rusting in back yards, mill throughputs below design and varying by 30%, cyclones flaring and cut-sizes fluctuating, mediocre recoveries and soaring processing costs. This disconnect between aspiration and reality appears, to these authors at least, to be a mighty chasm. Moreover, it remains one over which we are expected to magically leap rather than methodically bridge. Indeed one may be forgiven for thinking that should such a wonder machine come along, taking advantage of it would be highly improbable. Questions would inevitably emerge on how to feed the correct material, how to cope with the wide variability of feeds, how to control such advanced equipment and how to handle the new product from such a machine. It is likely these questions might lie unanswered, or more regrettably, unasked. It is generally accepted that as an industry we are exceedingly unlikely to teleport from the current status quo to an entirely new reality in a single flash. It is our thesis that the probability of these magical machines materialising is remote, and even if they miraculously appeared, we simply wouldn?t know what to do with them. Rather, it is our contention, that a step change will only arise through a staircase rather than from a single giant leap. We should focus on building those steps and linking them together into a firm structure ? a workable mineral processing circuit. This paper addresses the alternative of a coherent set of modest but significant improvements, integrated to produce the step change we desire: essentially, a reduction of processing energy to below 40%, which we believe is achievable without recourse to any mystical machines. A key underlying capability to designing these dramatically improved processes, is the weaving of independent process models into a coherent circuit simulation, in order to design the new generation of mineral processing circuits. Keywords: step change, circuit design, circuit simulation, energy reduction

Sep 1, 2012

By Aubrey Mainza, Malcolm S. Powell

"A hydrocyclone with two vortex finders, named the three-product cyclone (3PC), has been successfully tested in the Platinum industry for dealing with the dense Chromite found in UG2 ores. This dense component preferentially reports to the cyclone underflow, resulting in an over-ground fine Chromite component in the final product. The dense media effect caused by a high concentration of this in the cyclone feed produces a coarsening of the cyclone overflow, which results in loss of recovery through over-size silica in the PGM carrying component material in the float feed. The fine barren particles of Chromite that report to the overflow are recovered through entrainment in the flotation process, resulting in detrimental contamination of the slag produced from the concentrate.Data from many industrial scale tests of the 3PC have shown that three distinct products are obtained when the inner vortex finder length (LIVF) is extended to the region either above (normal classification) or below (reverse classification) the transition zone (a region were the inner and outer overflow streams are identical). Due to wear problems arising from extending the IVF deep into the cone of the cyclone, it is advantageous to use the shorter IVF. Only the normal classification results are reported here, but similar outcomes (to opposite overflow streams) were obtained for the reverse classification. The results showed notable differences in the percentage split of the plus 100µm material in the product streams, confirming that three distinct products are discharged from the 3PC. About 12% of the plus 100µm material in the feed reports to the middlings stream, 1% reports to the final product, and the remainder to the cyclone underflow.Results of silica and chrome splits to the three distinct products namely, the inner overflow (INO), the outer overflow (OUO) and the underflow (U/F) are given in Table 1. These show that the 3PC can be used to recover coarse silica through screening the middlings product - which has a high silica content. When the vortex finder ratios (ratio’s of cross-sectional areas) are carefully selected, the split of plus 100µm silica to the middlings product ranged from 2.9 to 9.6%. Large amounts of oversize silica and chrome report to cyclone underflow, explaining their high percentages in the underflow stream."

Jan 1, 2003

By A. Oberrauner

Electrostatic separation is a dry separation technique usable for many applications in the mining- and recycling industries. At the Chair of Mineral Processing intensified research has been done on this topic during the last years. One challenge was to measure the triboelectric charging of fine mineral particles in a triboelectric charging device consisting of an electrically insulated polyethylene rotor/stator assembly. These tests, performed on monomineralic samples, were accomplished in a climate chamber. It was shown that charging of minerals not only depends on rotor speed, feed rate and atmospheric circumstances but also on the properties of the applied electrostatic field. Tests on pure calcite in contact with the polyethylene rotor/stator system resulted in specific triboelectric charges up to +10 nC/g at low relative humidity. With more water present in the surrounding atmosphere, these charging values decreased significantly. However, at higher relative humidity, triboelectric charge values could be maintained after an electrostatic field of positive polarity was applied. Similarly, charging behavior was found with other hydrophilic minerals. The idea behind all these tests was to find the largest charging difference between minerals occurring together in a deposit and to be able to charge them oppositely, assuming that this means good sort ability in an electrostatic separator. The results gained from these investigations are shown. After having obtained many results on charging pure minerals, it became interesting to test the applicability of the charging tendencies on electrostatic separation of fines <100 µm. In order to do so, a separator for fine polymineralic powders was developed, constructed and combined with the triboelectric charging device, all being set up in a climate chamber. This new so-called coax-separator is presented along with first test-results.

Sep 1, 2012