Search Documents

By Olli Haavisto, Heikki Häkkänen, Tommi Kauppinen, Navid Khajehzadeh

Raman analysis is a well-established method for finding the abundant minerals in an ore sample. In this study, Raman spectroscopy is tested as a method for rapid and contactless on-line mineral analysis. Rapidness might enable on-site analysis of rock drillcore, which in turn would lead to more cost-efficient solutions in mineral exploration. This paper discusses the use of Raman analysis to identify minerals and to measure their concentration. The sample set under study consists of rock drillcore collected from Agnico-Eagle Kittilä Mine, Finland. Selected parts of the sample set are measured by Raman spectroscopy and the minerals are identified using reference spectra from a public source. Moreover, the direct measurement of concentration of different minerals with the help of Non-negative least squares (NNLS) optimisation algorithm is considered. The optimisation algorithm was constructed to form a linear combination of reference spectra which best represent the measured spectrum, or an average of measured spectra, from an ore sample. The results show that NNLS can identify abundant minerals in a given sample. Also through this method of analysis the results of a traditional point-count method can be expanded: It was observed that, due to grain size, multiple minerals consistently appear in the spectra measured over an area, which means that point-count method is not a proper way to interpret the spectra. This can be seen as a new result, as formerly the discussion has attended to other methods.

Jan 1, 2014

By F. Burat

At the present time, methods of mining and coal preparation produce tones of coal fines. The removal of water from these fines is necessary for economical and technological reasons. Supplementary processes that utilize different physical and chemical methods have been developed to in-crease the productivity of mechanical dewatering processes. Researches have shown that chemical reagents used along with conventional systems diminish moisture and increase the capacity and the yields of the dewatering method. In this study, the parameters of the vibrating screen (incline, frequency, feeding rate and screen size), the effects of the application of additional vertical mechanical vibration and surface active reagents (CTAB, SDS, Umectante B-70 and Kerosene) were investigated. At the end of the optimization experiments, 61.0% moisture was decreased to 42.3%. By keeping optimum conditions con-stant, the experiments have been conducted to determine most effective reagent. 41.2% moisture has been obtained with 5 g/t CTAB at the normal pH of the pulp, which were 7.25. By using vibrating screen with combination of the vertical vibrating mechanism, CTAB gave the best result of 40.7% moisture. Finally, the effect of increased surface area of the screen has been investigated and de-creased the moisture level to 38.7%.

Jan 1, 2014

By I. Gombköto

Mining and mineral processing operations are usually generating huge amount of tailings. These tailings often gives lots of maintenance work in order to protect environmental resources from heavy metals slowly leaching out of tailing are due to Acid Rock Drainage (ARD) process. Handling leakage could be active or passive such as using of Permeable Reactive Barriers (PRB). PRB?s are used worldwide treating underground contaminations, using different type of matrix materials. All generally used matrix material has its advantages and disadvantages such as selectivity, sensitivity of precipitation generation or not satisfying hydraulic conductivity. Nowadays cheap and effective matrix material which is ignorant to pore plugging caused by precipitation within the PRB could be one solution to the demands of the industry. The authors have been carried out an investigation at University of Miskolc on lignite as high humid acid containing material for determining the ability of heavy metal adsorption and pore plugging resistance. Moreover, using hydraulic and chemical simulation methods, complete PRB dimensioning protocol based on new lignite matrix had been introduced. Within the frame of this paper the results are going to be discussed.

Sep 1, 2012

By Lev Malytin, Alexander Dyachenko, Roman Kraydenko

"A new method of processing beryllium raw materials based on interaction of beryllium mineral with ammonium fluoride was developed. Possibility of extracting ammonium tetrafluoroberyllate from bertrandite and phenakite minerals is proved. The developed technology allows replacing the outdated sulfate technology developed by Materion Corporation. INTRODUCTION Beryllium is a strategic metal, which is produced only in three countries: the USA, China and Kazakhstan. The world production of beryllium amounts to only 300 tons per year. More than 75% of the world beryllium production is manufactured from oxide beryllium ores in the USA by Materion Corporation. In Russia there is a large-scale beryllium ore deposit «Ermakovskoye» containig over 1 million ton of ore. Concentration of beryllium in ore amounts to 1,2%. Since the mineral base of ore is calcium fluoride, the sulfate technology of Materion Corporation cannot be used. After alloying and sulphuric acid leaching the fluorine-ion found in fluorite and beryllium together evolve into the aqueous phase. At the stage of Be(OH) precipitation fluoride-ion prevents complete isolation of beryllium into the phase of hydroxide, which increases the loss of beryllium. A new ammonium-fluoride method for processing high-fluoride beryllium ores has been developed at Tomsk Polytechnic University. The ammonium-fluoride method involves fusion of ammonium fluoride (NH4HF2) with a beryllium concentrate. The concentrate containing 10% of beryllium oxide and 25% of calcium fluoride is produced by flotation from the ore of Ermakovskoe deposit. The main component of the ore concentrate is fluorite CaF2, which does not react with NH4HF2. Beryllium in this concentrate is represented by two minerals: phenakite Be2(SiO4)2 and bertrandite Be4[Si2O7](OH)2. Ammonium fluoride, unlike sulfuric acid, does not react with calcium fluoride and is not consumed for decomposing the mineral base of the concentrate. Ammonium fluoride is an accessible and environmentally safe reagent, worth up to $ 1,200 per ton. The total amount of ammonium fluoride is recycled and is used for decomposing a new batch of beryllium concentrate."

Jan 1, 2018

By Lev Malytin, Alexander Dyachenko, Roman Kraydenko

"A new method of processing beryllium raw materials based on interaction of beryllium mineral with ammonium fluoride was developed. Possibility of extracting ammonium tetrafluoroberyllate from bertrandite and phenakite minerals is proved. The developed technology allows replacing the outdated sulfate technology developed by Materion Corporation. INTRODUCTION Beryllium is a strategic metal, which is produced only in three countries: the USA, China and Kazakhstan. The world production of beryllium amounts to only 300 tons per year. More than 75% of the world beryllium production is manufactured from oxide beryllium ores in the USA by Materion Corporation. In Russia there is a large-scale beryllium ore deposit «Ermakovskoye» containig over 1 million ton of ore. Concentration of beryllium in ore amounts to 1,2%. Since the mineral base of ore is calcium fluoride, the sulfate technology of Materion Corporation cannot be used. After alloying and sulphuric acid leaching the fluorine-ion found in fluorite and beryllium together evolve into the aqueous phase. At the stage of Be(OH) precipitation fluoride-ion prevents complete isolation of beryllium into the phase of hydroxide, which increases the loss of beryllium. A new ammonium-fluoride method for processing high-fluoride beryllium ores has been developed at Tomsk Polytechnic University. The ammonium-fluoride method involves fusion of ammonium fluoride (NH4HF2) with a beryllium concentrate. The concentrate containing 10% of beryllium oxide and 25% of calcium fluoride is produced by flotation from the ore of Ermakovskoe deposit. The main component of the ore concentrate is fluorite CaF2, which does not react with NH4HF2. Beryllium in this concentrate is represented by two minerals: phenakite Be2(SiO4)2 and bertrandite Be4[Si2O7](OH)2. Ammonium fluoride, unlike sulfuric acid, does not react with calcium fluoride and is not consumed for decomposing the mineral base of the concentrate. Ammonium fluoride is an accessible and environmentally safe reagent, worth up to $ 1,200 per ton. The total amount of ammonium fluoride is recycled and is used for decomposing a new batch of beryllium concentrate."

Jan 1, 2018

By M. S. Eygi

This study covers the investigations based on the electrokinetic and rheological properties to explain the interactions between kaolin minerals and commercially available polyelectrolyte in anionic character. Additional adsorption test were also conducted to support the interaction mechanism. Adsorption tests showed that adsorption densities decrease by increasing the solid content. In-creasing the solids contents from 1% to 30% by weight resulted in the decrease on adsorption from 2.14 mg/g to 1.85 mg/g. Because of its difficulty, the solids ratio at 70% was not studied. However, following to trend of the curve plotted adsorption density-solid ratio, an estimation was made and adsorption density at 70% solid content was extracted from the curve as 1.75~1.80 mg/g. The electrokinetic studies pointed out that the presence of polyelectrolyte increase the zeta potential of kaolin from 40 mV to 60 mV which is reasonable conditions to disperse and stabilize the kaolin slurry and lower the viscosity. When these result of the different tests are combined and considered together, 2 mg/g polyelectrolyte concentration was noted as optimal concentration where adsorption density, viscosity and zeta potential of the slurries give maxima and remain constant after this concentration.

Jan 1, 2014

By V. Avzian Belozersky reg 453524, Vasily V. Lodeischikov, Adolf F. Panchenko, Til E. Vidusov, Olga D. Khmelnitskaya, Vladimir E. Dementyev

"Presently, there is a number of gold deposits which cannot be developed using the conventional technologies with acceptable economic indices due to low gold content, high depth of ore occurence and other conditions. For such ores, an innovation technology of underground gold leaching in the place of their occurrence is of special interest. The technology excludes ore mining and hoisting to the surface. This enables the production cost of 1 g of gold to be considerably reduced in comparison with conventional methods of gold recovery.The Maminskoye deposit oxidized ores were chosen as the subject of underground leaching because they are ideally suited for this purpose due to their composition and hydrological parameters. The ore reserves within the underground leaching block are 90, 000 t with 0.7 g/t average gold grade.An experimental system for underground leaching with a throughput of 15 cubic m solutions per hour was developed. A combined filtration-and-infiltration system of the ore massif development by holedrillingwhere pregnant solutions are air-lifted was worked out.The underground leaching flowsheet includes Au dissolution by chlorine-containing solutions, Au adsorption from solution onto active carbon, carbon concentrate ashing and calcine melting to produce Dore metal."

Jan 1, 2003

By Kazutoshi Haga, Atsushi Shibayama, Altansukh Batnasan

The objectives of this study were to propose a viable alternative method for recovery of precious metals such as gold (Au), silver (Ag) and palladium (Pd) from waste printed circuit boards (WPCBs) and to regenerate the spent lixiviant solution for reuse. The proposed method generally consists of several steps as follows: 1). iodine-iodide leaching for metals extraction; 2). separation and recovery of precious metals and metal impurities from a pregnant leach solution; 3). regeneration of the spent iodine-iodide solution/lixiviant. In this method, more than 99% of Au leaching was achieved in the iodine-iodide solution from the solid residue of WPCBs that was obtained via sequential processes including incineration at 800 ?C and high pressure oxidative leaching with a diluted sulfuric acid at 120 ?C, while the leaching of Ag and Pd was less than 1%, respectively. Besides Ca, Cu, Ni, Co and Zn as main metal impurities, leaching efficiency of other metals did not exceed 1%. The precious metals and base metals as metal impurities present in the pregnant leach solution were separated and recovered by precipitation using L-AA and NaOH solutions. About 99.8% Au, 81.7% Ag and 72.8% Pd were recovered from the pregnant solution at pH of 2 with the addition of 0.1 M L-AA as precipitating agent. The remained small amounts of precious metals and metal impurities were precipitated at pH 13 using 1 M NaOH. The spent lixiviant after sequential precipitation was regenerated in the presence of hydrogen peroxide, hydrochloric acid and potassium iodide. It was revealed that over 90% of gold could be extracted from the residue of WPCBs with the regenerated lixiviant solution.

Jan 1, 2018

By John C. Gathje, Rick Moritz, Wilhelm de Beer

"Froth flotation has a long history of success for the recovery and concentration of a wide variety of minerals of commercial interest. Both the art and science of flotation have progressed greatly, and as our knowledge has increased so has our ability to improve mineral separations and recoveries.One area of interest in recent years has been the flotation of refractory gold ores to recover the gold-bearing sulfides. In many instances, the use of conventional air flotation to concentrate these values has achieved only limited success. However, as a result of intensive research, Newmont Mining has expanded the boundaries of flotation, and it can now be used to successfully treat many gold-bearing sulfide ores as well as platinum and palladium ores. This has been achieved through the use of the N2TEC technology, which utilizes nitrogen as an inert gas in the flotation process.Laboratory and pilot plant investigations and a commercial plant have proven its worth. Compared to air, the patented N2TEC process has increased the gold recoveries of many ores by 5 to 15 percentage points, and improvements of an even greater magnitude have been observed. This paper describes the process development for the flotation plant now being operated at Newmont’s Lone Tree Mine located in Nevada, as well as development work that was done on ores from their Twin Creeks Mine also located in Nevada."

Jan 1, 2003

By H. Araneda

Throughout Chile?s history, mining has consistently been a leading industry in the country. The 1990s marked the beginning of a boom in Chile?s mining industry, especially in copper mining, due to both foreign and local direct investment in the sector. Mining?s contribution to the GDP was 15.6% at current prices in 2009, and it accounts for 56% of the country?s exports. Chile?s copper market share reached 35% in 2009. The investment portfolio in mining in Chile for the coming decade has been estimated at 90 billion US dollars. The acute scarcity of human resources currently experienced by the mining sector in Chile will be accentuated in the coming decade as a result of this scenario of investments. The situation is, additionally, similar to the one confronted by other countries involved in the mining industry such as Australia, South Africa, Canada, and in Latin America includes, Peru, Colombia and Brazil. A study carried out by Fundacion Chile, ¨Labor Force in the Chile Mining Industry, Diagnostic and Recommendations, 2011-2020? shows the projected labor shortage for the operation of projects in the development stage, considering only the requirements of the process of extraction, processing, and maintenance. The demand, accumulated incrementally, will be around 115,000 technically skilled workers, professionals, and qualified workers. This figure refers to the operational work force, and does not include the human resources that will be required for the prior stage of the engineering and construction of the projects (brownfield and greenfield). The demand for technically skilled workers and professions for the stages of engineering and construction of the projects that have already received investments is estimated to be 190,000 people for the period 2012-2020. The peak of the demand for engineering is 2012, with a figure that surpasses the 12,000 professionals for all of the engineering specialties. The analysis of the formation of human resources at the tertiary level (where tertiary includes technical/vocational and academic degrees at the undergraduate level) for mining and related majors demonstrates that the programs are scarce with a bias toward theoretical contents and that they are excessively long (40% longer than comparable programs in Australia, Canada, and in OECD countries). The completion rates are low, especially in the technical-vocational programs, which have a completion rate of only around 30%. Finally, the rates of attraction of technically skilled labor and professionals towards careers in mining are insufficient to reduce the identified skill gaps. In the case of university professionals such as geologists, mining engineers and engineers in metallurgy, 80-90% will work in mining. In the case of graduates of relevant majors, that cover skills also utilized by other industries, not only mining?such as maintenance workers, operators of fixed and mobile equipment, etc.?the mining sector appears to be unattractive for reasons such as shift schedules, geographical location of work sites, and other factors. On the basis of the available diagnosis a strategy for the sector has been developed (Workforce Development and Skills Strategy) whose objective is (i) to define a Mining Qualifications Framework to identify the critical roles to be filled (ii) to start, with public resources, a ¨fast-track? training program to assure the availability of at least 28,000 operators (machinery operators, truck drivers, etc.) and maintenance specialists in 2015 (iii) to promote the development of training hubs for mining with learning technologies to train technical labor and professionals on the basis of world class standards (iv) to design and implement a campaign oriented toward the perception of mining as an attractive field of employment opportunity (v) to develop curricular innovations for tertiary education programs, on the basis of international benchmarks. Keynotes: Chile, mining, copper mining, skilled human resources

Sep 1, 2012

Opportunities to monitor and control primary grinding mill performance are strongly sought after in the mineral processing industry. Currently, limited on-line information about mill charge motion and content is available to mill operations for control purposes, leading to periods of lower throughput, instability, variable product size and accelerated mill liner and lifter wear. In response to this need, CSIRO has developed an on-line surface vibration monitor for primary grinding mills which produces data that has been shown to provide new information about the mill charge in terms of toe and shoulder position, as well as potentially key features such as the overall charge level, the distribution between rock and balls in the mill, and the impact of the charge on the mill liners and lifters. This paper outlines the key features of the on-line monitor system, particularly those relating to data transmission, data analysis, and the design of the monitor and its independent power supply. It describes the coupling of single vibration sensor data from the CSIRO on-line monitor to the actual operating conditions of a SAG mill and how the vibration response and hence mill operating conditions vary as a function of time, including during mill equipment failures such as a broken discharge grate. Opportunities for improved mill control based on the data from the on-line monitor are also discussed, as well as the implications in terms of mill processing and maintenance performance. Recently a CSIRO monitor was also installed on a ROM ball mill and analysis of the vibration sensor data from this installation is currently underway. Preliminary findings from this installation will be presented along with comparisons of generic information, such as toe position (measurement precision and operation variability) and vibration signal (intensity, sensitivity and operation variability), between this type of primary grinding mill and AG/SAG mills.

Sep 1, 2012

By Rodolfo Silva, Antonio Peres, Afonso Martins, Gilberto Ramalho, Mario Cabello

The consumption of aggregates in civil construction has increased considerably in Brazil for the last years. The extraction of sand and gravel generates significant environmental impacts. As the quarries and sand deposits are getting exhausted near the big cities, the price of aggregates is increasing. Meanwhile, the extraction of quartzite (dimensional stone) in the state of Minas Gerais has been done mostly in small quarries, with very low recovery, generating approximately six million tons of wastes a year, which causes pollution, increases final prices of products, decreases the life time of quarries and ends up in the closure of enterprises. The government agencies and the quarries’ owners understand that only by finding applications to wastes there will be development to the sector. The aim of this investigation was to study the application to the quartzite wastes as aggregate in the civil construction. Samples of quartzite wastes collected in a quarry were characterized by petrographic analyses. Laboratory tests of crushing and grinding were done to analyze the viability of reducing the size of coarse material to a finer one to be used as raw material in industrialized mortars and concrete pre-molded components.

Jan 1, 2014

By Edgar Schach, Tom Leistner, Markus Buchmann, Urs A. Peuker, Martin Rudolph, Marius Kern

"In this study, the flotation characteristics of a cassiterite-bearing fine-grained and complex skarn ore from a deposit in the Ore Mountains is investigated. The tests are performed using an oil-assisted column flotation approach to process very fine ore fractions and avoid losses of cassiterite into the tailings. First, process parameters are obtained for a finely ground artificial mixture of quartz, magnetite and cassiterite, simulating the real ore. Thereby, magnetite is used, as iron oxides can have a detrimental effect on the flotation due to a similar flotation behavior. In addition, they can act as a source of multivalent ions, which are known to reduce the concentration of collector molecules, active for flotation. Based on the results, selected parameters are further tested for cassiterite skarn ore from the Hämmerlein deposit including a pre-conditioning and a water exchange step to remove ionic contaminants. The process response is analyzed in detail by XRF (X-ray fluorescence) and MLA (mineral liberation analysis) to get a better understanding of the behavior of the single ore components. Sulfosuccinamate type surfactant is utilized as the collector, emulsifier and to reduce the froth destabilization through nonpolar oil. Sodium hexafluorosilicate is added as the depressant.INTRODUCTION Complex skarn ore deposits containing considerable amounts of tin, indium and other metals are located in the Ore Mountains region (Germany). In this study, a skarn ore from the Hämmerlein deposit was investigated. Due to the finely disseminated nature of this ore, past beneficiation attempts failed, and the ore was considered economically unprocessable. However, increasing resource demands brings it back into focus (Schuppan and Hiller, 2012). Cassiterite is the main tin bearing mineral in this ore. Due to its high density (~7 g/cm³), the predominant beneficiation technique is gravity separation (Angadi et al., 2015). Tin ores from disseminated deposits have to be extensively comminuted to reach a sufficient degree of liberation of the cassiterite grains. As cassiterite has a brittle nature, it is preferable enriched in small size fractions, during comminution (Angadi et al., 2015). Gravity separation methods become more and more inefficient for particles smaller 40 µm (Falcon, 1982), causing tin losses of up to 30 to 40wt.-% (Angadi et al., 2015). Thus, froth flotation of cassiterite was first utilized in Altenberg in the Ore Mountains as an additional processing step to reduce the cassiterite losses into gravity separation tailings (Bulatovic, 2010; Gruner and Bilsing, 1992). Although the reported lower size limits for an effective cassiterite floatability are often smaller compared to other minerals, the flotation performance is in general decreasing for small particle sizes < 10 µm (Trahar and Warren, 1976). Therefore, different approaches have been already investigated for the flotation of such fine cassiterite fractions to overcome the limits in particle size. Bilgen et al. investigated the shear flocculation of cassiterite with a sulfosuccinamate collector (Bilgen et al., 1994). The agglomeration flotation of cassiterite has been tested by Schubert et al. (Schubert et al., 1966), in which the selective coagulation of fine hydrophobic particles and oil droplets leads to an increase of the effective particle size. Recently, Leistner at al. investigated an oil-assisted agglomeration flotation for ultra-fine cassiterite ore fractions (Leistner et al., 2016). However, a poor response due to an increased concentration of Fe and Ca ions, unselective oil/gangue coagulation and froth instability, that is caused by oil/frother interactions, has been observed."

Jan 1, 2018

By M. Paymardi, A. Foroutan, T. P. Oladele, M. Abbaszadeh

"Reducing the amount of zinc and iron in lead concentrate is one of the important aspects of processing in lead and zinc flotation plants which results in improvement of lead concentrate quality and prevents zinc loss. In mineral flotation industries, lignin sulfonates are known for their depressant properties for both non-metallic and sulfide minerals such as pyrite and pyrrhotite.This paper investigates the effect of lignin sulfonate on flotation of galena, sphalerite and pyrite in sulfidic lead and zinc bearing ores. Batch flotation tests were carried out on a high pre-activated zinc samples. The feed contains 0.9% lead, 2.3% zinc and 7.5% iron. The dosage of all reagents such as sodium cyanide, zinc sulfate, ethyl xanthate and methyl isobutyl carbinol (MIBC) were kept constant for lead flotation step except calcium lignin sulfonate (CLS) that was varied between 0 and 80 gr/ton.Results for lead rougher concentrate showed that the grade of lead increased by 2.7% while the recovery decreased around 4 % at the highest dosage of CLS. Furthermore, zinc recovery decreased by 6.3% with no significant change in grade. Iron recovery in lead rougher concentrate decreased by 2.3 % while the grade changed around 1%. In sphalerite flotation step, CLS dosage was changed in the range of 0 to 80 gr/ton while the dosage of other reagents such as copper sulfate, lime, amil xanthate and MIBC were kept constant. In this step, no decreasing in grade and recovery of zinc was observed, while iron recovery decreased. It was suggested that CLS has a depression effect on sphalerite in conjunction with other zinc depressants such as zinc sulfate and sodium cyanide. CLS was further used in plant with non-pre-activated zinc minerals. Similar trends were observed in plant.INTRODUCTIONlead-zinc sulfide minerals play an important role in the production of lead and zinc metals in the mineral processing industry (Luo, Feng et al. 2016). Due to complexity of the lead-zinc ores mineralogy, in some situations, their flotation properties vary significantly from one deposit to another one even in itself (Bulatovic 2007)."

Jan 1, 2018

By John Ralston

"Interfacial chemistry plays a pivotal role in bubble-particle capture, for it controls whether or not attachment occurs. Surface heterogeneity, degree of surface hydrophobicity, bubble nucleation and related phenomena influence the stability of the aqueous wetting film between a particle and an approaching bubble. The latter must be unstable if capture is to occur. Various techniques that may be used to quantify this interfacial, chemistry-dominated behaviour, are described.The efficient capture of specific particles by rising bubbles and the delicate control of interfacial chemistry that leads to selective capture are central issues in froth flotation. For efficient capture to occur between a particle and a bubble, they must undergo a close encounter, a collision process dominated by hydrodynamics. Should this encounter bring the particle and bubble within the range of attractive forces, the intervening liquid film between the bubble and the particle will drain, leading to a critical thickness at which rupture occurs. The liquid-vapour interface then retreats over the solid particle surface until a stable wetting perimeter is established. The particle and bubble are then joined after this attachment process. The particle may only be dislodged from this state if it is supplied with sufficient kinetic energy to exceed the detachment energy in this detachment process. These various events are now well documented and may be followed using high-speed videomicroscopy (Schulze, 1984; Nguyen et al., 2001).The process of collision can now be described quantitatively for single bubbles colliding with bubbles under various flow regimes (Dai et al., 1998) and appropriate scale up is possible for multiple bubble particle collisions occurring under turbulent conditions (Pyke et al., 2002). In this paper we will be concerned with the role of interfacial chemistry and how this influences the attachment process."

Jan 1, 2003

By Svetlana Krashenina, Nebojsa Petrovic, Oscar Lopez

"As easily mined gold deposits are becoming increasingly rare, gold producers are turning to the processing of ores with polymetallic and copper mineralization. These base metals can create metallurgical and waste handling/disposal challenges, which can render the project uneconomic. Base metals such as copper compete for the cyanide reagent used to extract gold, necessitating the need to increase cyanide volumes and consequently, cyanide consumption costs. Copper will also stabilize in tailings water as weak acid dissociable cyanide, a form that is both difficult and costly to destruct. SART (sulphidization-acidification-recycling-thickening) process technology can be applied to remove base metal interferences in gold projects. SART breaks the copper-cyanide complex and precipitates the copper as a saleable copper sulphide concentrate. With the copper removed, the cyanide can be regenerated as free cyanide for recycle to the gold recovery process. This improves cyanide utilization efficiency and mitigates copper presence in tailings. Additionally, copper recovery generates an incremental revenue source to further improve project economics. Engineering Dobersek GmbH together with BioteQ developed a SART and AVR testing program to recover cyanide and maximize operational efficiencies at a gold processing plant in Kazakhstan with high cyanide consumption in the leach circuit. Results from on-site testing demonstrated that up to 99.98% of copper can be removed and precipitated as copper sulphide and 60-90% of cyanide can be recovered from the AVR and recycled for leaching, reducing total overall cyanide use. This paper provides an overview of the testing methodology and results together with a discussion on the potential of SART to improve gold production operations to deliver both environmental and economic benefits."

Jan 1, 2014

By P. M. Solozhenkin, V. P. Nebera, V. D. Skorohodov

"Aqueous dispersions of air specifically prepared on the basis of flotation reagent solution acquire active properties in relation to the solid surface and may be imply as a medium for flotation ores. Such aerated solutions were defined as Activated Aqueous Dispersions of Air (AADA) with 5-6:1 ratio and the procedure of mineral separation was defined as a flotation process under non-equilibrium conditions. These procedures differ from conventional flotation mainly in reagent interaction with minerals through their adsorption films on gas bubbles simultaneously forming flotation complexes. Gas-liquid mixture is kept till an adsorption layer of reagents close to the limit value is formed on the surface of bubbles. The theoretical basis of AADA is considered.The results of two-phase gas- liquid mixture (AADA) were studied. Two versions of AADA were considered. Electrical surface potential of the air bubbles with the surfactant film, untreated minerals particles in Coulomb attraction and flotation complex formation were analyzed. Special flotation machines were constructed for separation of mineral suspension in air dispersion, whose effectiveness was confirmed in flotation of apatite waste of Kovdor ore. FK-9 machine introduced on Kovdor iron ore combine for the recovery of apatite from current departures of factory. The froth product contained 7.2 % P2O5, with recovery of 44 % apatite, which was processed for getting melted phosphoric-magnesium fertilizers."

Jan 1, 2003

By M. Kosugi, M. Kawata, J. V. Satur, K. Mitsuhashi, R. Kawarabuki, W. Kracht, Y. Ebisu

Copper concentration is becoming more difficult because remaining copper ores are more complex and of finer copper mineral grain size, making copper minerals harder to float because of the fine particle size required to liberate the valuable species. The purpose of this work was to study the flotation behavior of fine copper sulfide ores at different conditions of agitation and aeration. The experimental campaign was carried out in a laboratory Denvertype flotation cell of 1 L volume modified to be operated with forced air that allows decoupling air flow rate and agitation speed. Four ore samples from Chile were used, all of them containing copper sulfides such as chalcopyrite, bornite, chalcocite, and tennantite, but with varying grain sizes and compositions. Preliminary flotation tests for establishing the flotation conditions of grinding size and collector dosage were conducted before the kinetic flotation tests that were carried out at different agitation speeds varying from 900 to 1300 rpm for gas flow rate ranging from 1.6 to 7.2 L/min. The flotation products were analyzed by ICP-MS and MLA (Mineral Liberation Analyzer). The results showed that high agitation speeds with corresponding air flow rates resulted in better recovery than moderate agitation speed and air flow rate, and an excess in gas flow rate resulted in bad performances. The flotation rates of the fine copper minerals were improved despite the different improvement rates among the fine size fractions. The impact of these operational variables, however, was different when comparing the results for the four ore samples. While it was found that the order of floatability in the four samples was the same, that is, chalcocite > tennantite > bornite > chalcopyrite, the kinetic constants of the copper minerals in the samples were different, indicating that mineral composition in the sample affects the flotation kinetics.

Jan 1, 2018

By A. A. Novoselov, U. Kelm

"Large volumes of mine tailings accumulated in surroundings of porphyry copper deposits represent a growing threat to environment. They contain significant concentrations of toxic metal and metalloids which can contaminate river runoff, ground waters or can be transported by wind. Both extreme pH of fluids in tailings impoundments and high surface areas of processed mineral grains provide their increased reactivity. As a result, during only a few decades, As, Cu, and Mo can be mobilized, redistributed through the tailing column and accumulated through post-deposition leaching, evaporation and contamination with natural fluids. Those processes are reflected in the forming of secondary minerals. Gypsum, Fe oxides/hydroxides, efflorescent salts and clay minerals are typical alteration products in tailings. Here we present the results of reactive transport simulations implemented on the base of PHREEQC and SUTRA codes. The one-dimension model emulates the mass balance between rainfall, evaporation and subsurface runoff, the kinetically- and thermodynamically-driven dissolution of tailing minerals, advective and diffusive transport of tailing fluids, and precipitation of secondary phases. A typical tailing column is composed of four unequal layers with predominance of (i) evaporation, (ii) secondary mineralization above, (iii) below water table, and (iv) near the bottom of dump. Those horizons are characterized by contrasting pH, chemical composition and bulk mineralization of pore fluids, distinct accessibility of atmospheric oxygen and, as a consequence, distinct intensity of sulfide oxidation. The modeling and its verification on Chilean tailings impoundments reveal the complexity and high rates of secondary mineralization. The accumulation of toxic alteration products is controlled by fluid transport through the tailing column induced by both rainfall/evaporation and exchange with subsurface runoff. The geochemical modeling is a powerful approach which allows comparing the processes in tailing deposits produced by distinct flotation regimes and providing the long-term predictions of their environmental impact as well as identifying sectors of tailings for possible re-processing."

Jan 1, 2018

By Antoineta Boteva

A significant part of the currently production of the non-ferrous and precious metals is from sulfide ores. Character feature of sulfide ores is the presence in them always pyrite and wide range of different sulfide minerals else. These minerals are the carriers of valuable for industry metals. Due to the low content of the main components, very often call on the use of collective- selective flow-sheets. The extraction of minerals in the collective concentrates determined in a large extent the effectiveness of the collective-selective sheets. In conditions of bulk flotation kinetics to floatate of the various minerals is different. Due to why it is and how it can be used for a more effective selection of minerals ?this is the main task of this report. For this purpose are used results from the bulk flotation of pyrite, copper sulfides, molybdenite, galena, blenda. It is separated and place of host rocks. Base it of large experimentation material, including both electro-kinetic measurements of mineral systems, as well as laboratory flotation tests and factories monitoring it is established kinetics of flotation of mineral particles in conditions of collective flotation. Made an effort to clarify the effect as of the species and the proportion of different sulfide minerals involved in flotation pulp else. Traced was the impact of the density and aeration of the flotation pulp on deferens in kinetics of mineral flotation in condition of balk flotation. The obtained results are used to increase the efficiency of the diffraction flotation of the complex sulfide ores containing precious metals. In the schemes, it is possible precious metals to fall in the most appropriate for the next processing products. Keywords: flotation, sulphide ores, kinetic extraction

Sep 1, 2012