Search Documents

Considerable attention has been, and is being, given to the physics of water-films associated with bubble interactions at surfaces. In contrast, little information on the chemistry of such films has been reported. This communication reports a method using sum frequency vibrational spectroscopy (SFVS) to describe hydrogen bonding of interfacial water molecules in water films created with bubbles at hydrophilic and hydrophobic surfaces. The SFVS spectra of water films at hydrophilic silica surfaces differ significantly from the spectra of water at a hydrophobic silica surface. The SFVS spectra indicate that a very ordered water structure exists in water films at the hydrophilic silica surface during contact with a bubble and that the extent of hydrogen bonding increases with an increase in contact pressure. Such structural considerations as well as repulsive electrostatic and Van der Waals forces account for film stability for a bubble at the hydrophilic silica surface. In contrast, the SFVS spectra of water at a hydrophobic silica surface show a lack of hydrogen bonding and are characterized by a distinct absorption at about 3700 cm-1 similar to the spectrum of the air/water interface. These results suggest the presence of a water void, or water exclusion zone, at the hydrophobic surface, as supported by X-ray reflectivity measurements reported in the literature, by atomic force microscopy, and by the results from molecular dynamics simulations. Of course the water film at the hydrophobic surface is unstable with film thinning and rupture upon bubble contact. Under these circumstances it is shown that an attractive Van der Waals force between the bubble and the hydrophobic surface can be expected when the water exclusion zone is taken into consideration. As the thickness of the water exclusion zone increases to a thickness corresponding to the size of nano bubbles, the calculated attractive Van der Waals force increases. This analysis may help to explain the so-called ?short range? and ?long range? hydrophobic forces. Keywords: SFVS spectra, hydrophilic silica surface, hydrophobic silica surface

Sep 1, 2012

By Sanjay Agarwal

Polymetallic sea nodule is a good source of manganese having 22.3% Mn, 5.4% Fe, 6.14% Si, 1.1% Cu, 1.15% Ni, 0.076% Co & others. These nodules are available in plenty on the sea beds, generated over thousands of years. Nodules mainly consist of manganese dioxide and iron oxide phases and other metals are entrapped in the complex cage of these Mn-Fe oxides phases.World-wide research is going on sea nodules as an alternative future source of many metals, which has led to intensified efforts to develop practical and economical processes for recovery of these metals. Very little attempt has been made world over on manganese extraction from sea nodules. We at CSIR-NML, India have developed a direct reduction smelting process of nodules to recover manganese as Fe-Si-Mn alloy. This alloy is extensively used in the steel industry as deoxidizer and as an alloying element to make different grades of steel. Lab scale experiments were conducted to study the manganese distribution between Fe-Si-Mn alloy and FeO-SiO2-MnO-CaO-Al2O3-MgO slag at different temperatures by varying the basicity of the slag. The direct reduction smelting of nodules is carried out on 1 kg scale in 50 kVA electric arc furnaces to have Cu, Ni and Co alloy and Mn rich slag. This manganese rich slag is further treated in 50 kVA arc furnace to produce Fe-Si-Mn alloy. The composition of Fe-Si-Mn alloy obtained is in the range of Mn: 60-65%, Si: 14-17%, C: 1- 2%, S: 0.03% and the balance iron which is acceptable grade for industrial use. The equilibrium amount of MnO in the final slag is controlled by the temperature of the final melt and the silica, lime, alumina content of the final slag. Increasing the basicity of the slag plays a major role in minimizing the loss of MnO to slag, increasing the amount of SiO2 of the slag, increases the manganese loss in the slag. Increasing the CaO/ Al2O3 ratio of the slag decreases the manganese loss in the slag. Increasing the MgO/CaO ratio of the slag increases the manganese loss in the slag. Thus by adjusting

Sep 1, 2012

By B. K. Gorain

Mining of low grade deposits along with the necessity to design and operate flotation plants with high throughput presents unique metallurgical and environmental challenges that need to be addressed to reduce project risks, improve project economics and to sustain the profitability of operations over the life of a mine. Some of the key challenges include poor recovery of valuables and concentrate quality issues due to complex mineralogy, the need to use poor quality water such as brackish or sea water, reduce environmental impact from the process, integrate flotation with hydrometallurgy to maximize precious metals recovery, escalation of capital and operating costs, use of unproven technology and constant use of larger equipment, high ore variability, worldwide constraints on resource availability and an ever increasing need for reliable metallurgical input to financial models to evaluate economic viability of projects. The need to develop effective solutions to these problems in a short time frame is becoming a key to the success of any new project and for sustaining the profitability of a mining operation. An integrated multi-disciplinary approach to problem solving is crucial with the need for a more lateral thinking along with strategic partnerships and collaboration involving the right players. This paper presents some of the key findings based on experiences from a large number of challenging projects and operations focused on solving complex flotation problems Keywords: mineral processing, flotation, flotation problem solving, flotation optimization, plant design, innovation

Sep 1, 2012

By Jun Xiao, Jianwen Yang, Yanhong Dong, Daixiong Chen

"MANGOTE Surface oxidizied mine is a gold-bearing deposit in Congo's Mai-Ndombe Province. In the past decades, the ore has been exploited in a crude way by local farmers, which directly causes the severe processing difficulty and lack of economy of cyanide leaching. Hunan Research Institute for Non-ferrous metals (HRIM) is currently investigating options to recover gold through understanding the mineralogical characteristics of MANGOTE surface oxidized ore. Chemical analysis , X-ray diffraction(XRD) and Quantitative Evaluation of Minerals by SCANing electron microscopy (QEMSCAN ) were conducted on samples from mine site. The bulk analysis results showed that gold separation of gold from gangue minerals was feasible after grinding the ore samples to 86.53% -74µm and adjusting the pulp specific weight at 100g/L, and gravity separation was conducted with using spiral chute after grading of fine particles. The research results highlight relationship between mineralogical characteristics of abandoned ore and economy of comprehensive utilization that might be directive experience to similar cases. INTRODUCTION The occurrence state of gold in natural gold minerals determines the basic recovery and recovery effect of gold(Komnitsas, C., & Pooley, F. D. 1989). The occurrence of gold in the ore refers to the form of gold in the ore.Generally the existing state of gold can be divided into four major categories according to the viewpoint of the dispersion system: independent minerals and gold, a coarse dispersed system;colloidal gold, a colloidal dispersion; solid solution gold, is atomic ion dispersion; adsorptive gold, according to the adsorbed particle is the micelle or ion, respectively is a colloidal dispersion or ion dispersion(Mao, S. D., & Yang, R. S. 2009; Liu, J. J. et al. 2007; Horisberger, M., & Rosset, J. 1977; Li, Y., & Audétat, A. 2013).With the increasing technology of comprehensive utilization of resources,varied plants can now process different gold ores with various occurrence states(Neesse, T. 2014; 7. Ogundare. et al.2014)."

Jan 1, 2018

By Diana Drinkwater

As ore grades decline, ore deposits get harder and mineralogical complexity increases, metallurgical skills are more important than ever to ensure that today?s mining operations are operating efficiently and profitably. Yet specialist undergraduate degree programs have all but disappeared and metallurgical skills training for graduate engineers in the workspace if often haphazard. In response to this situation, specialists at the JK Centre in Queensland, Australia, have put together a professional development program designed to fast-track skills development for early career metallurgical professionals. The program, called ?MetSkill ® ?, is offered as a group training package for young metallurgists in the workplace. It is centred on a meaningful technical investigation negotiated between the JK Centre delivery team and the client company. As well as learning about project management and data collection and analysis, the participants study specialist topics such as comminution, flotation and mineralogy under the tutelage of senior research and consulting professionals. The technical investigation provides an opportunity for immediate practice of these new skills and JK Centre specialists are on hand to provide feedback and support throughout the program. The participants are employed across different operations in Australia and the Asia-Pacific, and although they occasionally come together for group training activities they are often separated by considerable distance. Specialist educational professionals from The University of Queensland have provided an innovative web platform to support collaboration and communication between all participants. This paper will describe the MetSkill ® program in detail, as well as providing a report on its initial roll-out to 2 groups of Australian graduate metallurgists in 2012

Sep 1, 2012

Taknar polymetal (Cu-Zn-Au-Ag-Pb) deposit and concentration flotation plant are located in the northeast of Iran. The flotation feed contains Chalcopyrite, sphalerite and pyrite with 4, 4 and 8 percent respectively. Cu and Zn contents are 1.26 and 3.5 present. Pyrite decreases the quality of base metal concentrates and increases the amount of sulfur compounds produced in the base metal extraction processes. Therefore, depression of pyrite is essential in the concentration of base metal sulfides by flotation. For flotation tests, 4 mixed collector systems, MIBC (20g/t), lime and tow depression systems (sodium cyanide (60g/t)-zinc sulphate and dextrin (300g/t)-zinc sulphate) were used as collector, frother, pH regulator and pyrite-sphalerite depressants in the chalcopyrite flotation stage, respectively, and SIPX, MIBC, lime and copper sulphate (as activator) were used in sphalerite flotation from first stage tailings. The results have shown that, sodium cyanide is a suitable depressant for pyrite and sphalerite in the first stage of flotation. Compared to dextrin as depressant, chalcopyrite recovery was decreased approximately 1.83%. In addition, when sodium cyanide was used as pyrite depressant, copper sulphate consumption raised approximately 90 g/t for activation of sphalerite. From Environment and HSE points of view, dextrin is natural, biodegradable, and non-toxic while cyanide is very high toxic. Keywords: sequential flotation, Cu-Zn massive sulphide, pyrite depressant, dextrin, cyanide

Sep 1, 2012

By Rogerio de Oliveira Baldoino

The sedimentary phosphate deposit of Bayovar is located in a very dry area of Peru (desert of Sechura) which is close to the Pacific coast. It consists of seven superposed layers (beds) which call for different strategy of concentration. The ore is composed predominantly by apatite (84% in weight basis) plus silicates (16%). In order to treat the ore from beds 1-5, a suitable standard mineral processing circuit (composed of scrubbing, screening, attrition and desliming) started its operation in 2010, yielding 3.9 Mt/y of concentrate assaying 30% of P2O5. To concentrate phosphate from beds 6-7, however, it is necessary to carry out further cationic reverse flotation of silicates, at neutral pH, to yield a concentrate, which meets market specification. The new process was developed in laboratory scale by a collaborative program conducted between Vale S.A. and the University of Sao Paulo-Brazil. A pilot plant has currently been running in order to confirm the very good results yielded in laboratory scale. The successful accomplishment of flotation in the current beneficiation flow sheet will enable a capacity expansion of 1.9 Mt/y of concentrate assaying 30% of P2O5. As water resources are very limited at Bayovar region, all the steps of concentration, including flotation, must be performed with seawater, which must be continuously recycled. This work addresses some relevant topics related to the use of seawater in the reverse cationic flotation of silicates: influence of temperature, water quality (ageing and chemical composition) and collector type (ether amine versus condensate). The results indicate that condensate amine works better than ether amine. If flotation is conducted with the former collector, the separation process is able to tolerate changes in temperature (25-40oC) and water quality caused by either evaporation or ageing. Keywords: phosphate, flotation, seawater, temperature, ageing, concentration, salt

Sep 1, 2012

By L. M. Wang

Chengmenshan Copper Mine Concentrator adopts the new process of preferential?bulk stage floatation and utilize reground, largely increase the mineral processing index of the copper and the sulphide concentrates. In addition, the paper describes the remarkable economic benefit of the new process through the comparison of the new and the old processes.

Jan 1, 2014

"The most common comminution testing methods and the associated analytical procedures provide average values and do not capture the variability in breakage behaviour of ore particles. Therefore, plant designs and process performance predictions use only average values; hence, the inherent variability that exists within an ore domain translates into variation in process performance. This paper discusses the drawbacks of using the average approach to impact comminution testing and plant design. It considers breakage intensity from a single-particle testing perspective. To clearly delineate breakage behaviour of each broken particle, an experimental technique using the JK Drop Weight Tester (JKDWT) has been developed by which actual comminution energy per particle and breakage intensities were measured directly. Four different ore types in ranges of -45+37.5mm and -22.4+19mm were tested at three energy levels of 0.1, 0.25, 0.5 kWh/t and six energy levels of 0.5, 1.0, 2.0, 2.5, 3.0 and 4.0 kWh/t, respectively. Sieved results of individual particles, notionally, t5, t10 and t50 showed the presence of large variability in their breakage behaviour, which was not captured by the standard JK impact breakage testing approach. In addition, the original JKMRC model is modified by introducing a third parameter, ‘Emint10’ which describes the minimum energy required to produce the minimum percent t10 for a given ore type and its significance is tested statistically. These results suggest that the analysis of breakage variability may lead to more robust plant designs. Perhaps, the most useful insight from this work is to extend single particle breakage model developed by JKMRC to a comminution percentile envelope which may provide a more detailed picture of ore breakage variability. INTRODUCTION Rock consists of mineral grains, pores, voids and cracks that may differ markedly in size/density which make rock a heterogeneous material by nature. The degree of heterogeneity in rock affects its breakage characteristics where these variations increase local differential strain and stress within a stressed rock (Scholz, 1968) and it depends on many factors such as rock genesis, alterations, etc. One important aspect of this heterogeneous feature is presence of a large amount of experimental scatter in rock breakage results when considered from a quantitative perspective (Bieniawski, 1967; Liu, Roquete, Kou, & Lindqvist, 2004)."

Jan 1, 2018

By R. ?. Shishmarjov, Yu. ?. Davidenko, S. V. Bukhalov, ?. S. Baksheev, M. S. Shkirya, N. ?. Aikasheva, D. V. Bogdanovich, ?. Yu. Faustova

"The goal of prospecting operations in the Republic of Altay was to locate gold-sulfide-quartz mineralization. For this purpose we applied the technology of electromagnetic sounding and induced polarization (EMS-IP). These operations resulted in localizing promising sites with presence of sulfidization. The EMS-IP method proved to be highly efficient amongst other prospecting methods targeted at recognizing zones of sulfide mineralization making up 91%, considering that in more than half cases the ore intervals were the case. In the Yakutian diamondiferous province the EMS-IP technology was approbated during three field seasons to accomplish the assignments on searching for kimberlite bodies under conditions of various geological types. As a result, the reference objects were distinguished, and geoelectric parameters of kimberlite pipes of explosion were defined.INTRODUCTION In the time span 2015-2016 in Gorny Altay the EMS-IP technology was approbated in the Novokuznetsk area. The on-land areal geophysical survey was performed by EMS-IP method applied to identify, outline and locate promising sites with Au-Ag-bearing polymetallic mineralization within surveyed areas. Compared to the hosting rocks, the sulfides contained in polymetallic mineralization are typified by low specific electrical resistivity (SER) and high polarization. The areal survey conducted via EMS-IP method provided spatial characteristics of searched object. From July 2016 to August 2017 our expedition group carried out serial test works and laboratory investigations intending to define performance capabilities of EMS-IP technology in searching for kimberlite bodies under conditions of diverse geological types. The prerequisites for serial work were operations accomplished at the «Listvenichny» site lying 35 km away from Mirny town in the Sakha Republic (Yakutia), where the EMS-IP technology was probed for locating position and measuring geoelectric parameters of tuff pipe «Buardakhsky». After successful completion of operations it was decided to evaluate geoelectric parameters of kimberlite pipes of explosion."

Jan 1, 2018

Hydrofluoric acid (HF) is traditionally used in plant operation to separate feldspars from quartz. It acts during the conditioning step as a pH regulator and an activating agent providing an excellent selectivity. However, a corrosive chemical environment and the ecological impacts from the potential fluoride ion contamination are limiting factors to use this chemical agent at an industrial scale. Investigations of the amine-feldspar interactions in the absence and presence of non-linear long-chain alcohols were carried out on two ore samples. The presence of alcohol molecules led to form a closed packed layer only on the surface of feldspars. The highest order and packing at the feldspar surface were observed with a particular alkyl chain structure as Guerbert alcohols. A new flotation process was developed and tested at both lab and pilot scales on different feldspar ores. The Guerbert alcohols allow to perform a feldspar concentrate with very low content in quartz (2.3-3.5 %) and feldspars recovery from 78 to 81 % while the aliphatic isoalcohols show a more higher recovery level (88-89 %). New HF-free process is strongly dependent on the pH range (1.7-2.5) and sulphuric acid consumption during conditioning steps. Optimal amine/alcohol weight ratio is ranged between 0.8 and 1.0. The values below 0.8 decrease strongly the flotation selectivity and the quartz recovery within the feldspar concentrates is higher than that occurs with HF.

Sep 1, 2012

By Graeme Heyes, Warren J. Bruckard, Michael A. Somerville

"A limited series of laboratory batch flotation tests was conducted on a suite of calcium-ferrite-based slags made in laboratory smelting trials. The smelting tests were conducted as part of a wider CSIRO Minerals’ research project aimed at developing a single-stage continuous copper-making process. The objective of the flotation work was to maximise copper recovery and iron rejection from slags made in the process.The slags treated included a reduced low copper slag, an oxidised high copper slag composite, and a very reduced low copper self-pulverising slag. The copper content of the slags varied from 2.9% to 14% Cu. The copper was present as metallic copper, oxide copper and copper-calcium ferrite phases with the phase mix related to smelting conditions. The slags were crushed, ground, wet-screened at 355 or 210 µm to remove coarse metallic particles of copper, and floated at natural pH (about pH 11) using reagents and conditions appropriate for the selective recovery of the copper phases.In rougher/scavenger tests on the reduced low copper and self-pulverising slags copper recoveries above 92% were obtained with copper enrichment ratios varying between 2.3 and 2.9. For the oxidised high copper slag copper recoveries were poorer - only 47% of the copper was recovered with an enrichment ratio of 3.3. The presence of the slow floating copper-ferrite phases in the slags limited further (selective) copper recovery. Ageing of the high copper slag, that is, a significant delay between grinding and flotation, resulted in a deterioration of the copper flotation response.The critical parameter affecting the flotation of copper from direct converting slags was found to be the form of the copper in the slag. Slags containing a higher proportion of the more desirable form of copper for flotation will provide the best opportunity for high copper recoveries to be consistently obtained, allowing improvements in the economics of the overall copper-making process."

Jan 1, 2003

Low-grade ore bodies, increase in rock competency, finely disseminated valuable minerals in the ore bodies, ore variability and water scarcity are among the technical challenges faced by the mining industry. These challenges have increased the business risk, capital investment and operating cost of the mining projects. Since the last 20 years, many large-scale concentrators have been built to cope with the above-mentioned challenges. Comminution, especially the fine grinding is an energy-intensive process. For example, the ball mill has a limitation in the fine grinding regime where the energy consumption increases exponentially when the product size is below 45 µm. The industry has been seeking for solutions that have a minimum risk and total cost of ownership. The stirred milling technology such as the TowerMill is well accepted by the industry as it has demonstrated the attributes required for fine grinding. TowerMill is a matured technology that has been adopted since the 80s for regrinding duty. Recently, this technology was installed in secondary and tertiary grinding duty to prepare a finer feed to rougher flotation. Four units of TowerMills were installed in a magnetite concentrator in Western Australia in tertiary grinding duty. Recently, Nippon Eirich has conducted process performance evaluation on the TowerMill circuit. The outcome of the exercise had indicated that the circuit is consuming 3.4 kWh/t to reduce from 55 µm to 35 µm with a narrow product size distribution. The effect of operating variables such as the specific energy, grinding media size, mill content % solids and mill feed configuration on the grinding efficiency were evaluated at the plant scale. Furthermore, the scale-up methodology was validated. The scope of this paper includes the performances of TowerMill and the validation of scale-up methodology.

Jan 1, 2018

By T. V. Vijaya Kumar

Most of the iron ore washing plants set up in India consist of sizing of the ore by dry / wet screening, washing and classification by screw classifiers followed by multi-stage hydrocycloning of screw classifiers? overflow. The underflow of the hydrocyclones forms the concentrate which is used for pellets making. As the cut-point of hydrocyclones is generally at 20 microns, relatively lower diameter cyclones in a cluster with parallel feeding are used. This is found to, often, result in choking of the spigots, at times, by extraneous material as well reporting along with the slurry. It is observed to lead to sub-optimum performance of the cyclones with loss of iron values into cyclone overflow and thereafter into tailings. Analysis of data of an operating beneficiation plant (Beneficiation Plant - 1, BP - 1) of M/s Jindal South West (JSW) Steel Limited, Karnataka, India over a period of one year indicated that weight recovery of the concentrate from two-stage hydrocycloning was 45% (with respect to feed to the cyclones) and assaying 63.43% Fe, 4.43% SiO2 and 2.32% Al2O3. CSIR - National Metallurgical Laboratory - Madras Centre (NML - MC), India developed flotation process for processing screw classifier overflow with a view to improve the recovery of ultrafine iron values from it. Detailed investigations at laboratory scale flotation column and on-site pilot plant trials proved that the production of the concentrate and productivity of the plant could be enhanced by adopting reverse cationic column flotation technology. It was established that a typical screw classifier overflow analyzing 60.54% Fe, 5.95% SiO2 and 3.67% Al2O3 could be upgraded to 64.21% Fe, 2.64% SiO2 and 2.20% Al2O3 with 82.7% weight and 84.7% Fe recovery. This translates into an increase of 80% in weight recovery of the concentrate compared to what is being obtained, at present, by two-stage cycloning. It had an added advantage of reduced SiO2 in the concentrate. Thus, SiO2 in the final concentrate could be reduced to 2.64% from 4.43% by adopting column flotation. The concentrate so generated meets the stringent specifications, especially in terms of alumina in it(should be less than 2.50%) for pellets making. Later, JSW Steel Limited set up the flotation plant in BP - 1 based on the process developed by NML - MC and was commissioned in 2010. Keywords: iron ore, washing, ultra fines, alumina reduction, column flotation

Sep 1, 2012

By Carina Ulsen

The existing construction and demolition (C and D) waste recycling technologies and standards have been essentially focused on the production and use of coarse recycled aggregates. Very few papers focus on the production of recycled sand, although some previous results show that fine aggregates fraction represents around 40 to 60% (in mass) of the Brazilian waste and it is usually used as road sub-base or disposed in landfills. The quality of the recycled aggregate is strictly related to the content of porous and low strength phases, mainly the patches of cement remaining on recycled aggregate surface. Some technologies have already been described in the literature, even though, to the moment none of these technologies has clearly succeeded in reaching the large market available. This paper presents a summary of the main properties of the sand produced from C and D waste by tertiary crushing at vertical shaft impact crusher (VSI). Additionally mineral processing technologies were applied on the attained product, such as gravity concentration by shaking table and spirals and removal of cement paste by attrition. The main properties of recycled sand are discussed and compared to the previous C and D waste, respectively: particle size distribution, particle shape, chemical composition, cement paste content and porosity. The results demonstrates that the crushing allowed producing a VSI-sand with low porosity and water absorption due to the increasing on the content of silicates from natural rock phases and increasing liberation between these phases and porous cement paste; the particles from the attained product presented also a better shape (sphericity and aspect ratio). The attrition tests assayed on VSI recycled fine aggregates accomplished a further selective disaggregation of cement paste and other porous materials - the porosity was reduced from 10% to 7%. The concentration by shaking table at narrow sieve fractions led to a product with low porosity and reduced content of cement paste, however, concentration on spirals did not succeed since separation was performed essentially by the size of the particles. The heavy product from shaking table represented almost 75% in weight and has less than 60% recovery of CaO+LOI, and expressive reduction on porosity. The aim of producing sand from construction and demolition waste through mineral processing unit operations changes the recycling approach and contributes for up cycling the recycled sand. The exhaustion of sand deposits on Brazilian large centers, the increasing price and the construction boom encourages the development of alternative materials as construction raw material. Keywords: recycled sand, construction and demolition waste, technological characterization

Sep 1, 2012

By O. A. Bascur

It is difficult to analyse the economics without an integrated view of mine transactions, stockpile inventories, process flows and assays. The lack of integration of mining and metallurgical information with sufficient detail to analyse and act is a problem. However, to take action requires real time information from manufacturing assets, corrected for gross errors from trucks, shovels, conveyors, faulty sensors, bad instrument calibration. Validation methods use process models to identify inconsistent information in the case of corrupt actionable information. This paper presents new strategies that transform the data into business information for continuous improvement and optimization. This technical presentation will review recent implementations enabling large metallurgical complexes to improve their data quality for overall production and energy management. A competence center emerges as an enabler for implementing operational intelligence. The evolution of Web services to troubleshoot plant information and to collaborate at the enterprise level is presented.

Jan 1, 2014

By Arkady Senchenko, Yevgeny Zhagun, Yury Kulikov, John Starkey

"The paper contains description of a new project in Russia - gold-processing plant at Aleksandrovskoye deposit (start up in September, 2013). The paper includes a brief description of plant flowsheet, data for material composition and technological properties of ore, as well as information about the achieved parameters of ore processing over the first months of plant operation. The project is interesting because a new semiautogenous mill and a ball mill were purchased on the basis of SAGDesign Consulting Group recommendations after the testing of ore samples characterizing the deposit according to specific years of operation. The plant has relatively small design capacity - 750 000 tpa, but nevertheless is the biggest gold-processing plant in the territory of Zabaikalsky region. Major valuable component in the ore is gold, silver is recovered as a by-product. The ores are very hard to grind. The design grinding flowsheet includes a semiautogenous mill operating in closed circuit with a screen, and a ball mill operating in a closed circuit with hydrocyclones (SAB). Process technology includes gravity processing and flotation with subsequent cyanide leaching of concentrates. Mill operation analysis and conclusions about the compliance of the achieved values to target ones are shown, as well as the accuracy of SAGDesign method when applied to very hard ores of Aleksandrovkoye deposit are presented in this paper. Basic directions of technological flowsheet optimization are also given."

Jan 1, 2014

By Xiong Dahe

In recent years many creative technologies are applied to SLon vertical ring and pulsating high gradient magnetic separators. SLon-2500 and SLon-3000 vertical ring and pulsating high gradient magnetic separators are created towards larger scale. Through optimizing the magnetic system and lowering the electric current density, their energy consumption is obviously dropped. New magnetic matrixes are developed to raise the beneficial efficiency of valuable minerals. Special SLon vertical ring and pulsating high gradient magnetic separators are developed which can treat coarser particles of 0-5 mm. Through these technology creations, the mineral processing efficiency of SLon magnetic separators is further raised and their processing cost dropped. Therefore, they have been found wider applications. SLon-2500 applied in Essar Steel of India. In 2007, Essar Steel did a test on its Kirandul hematite ore with SLon magnetic separator and got very good results. The feed grade is 59.77%Fe, after SLon one roughing and one scavenging, the total iron concentrate grade is 65.00%Fe and iron recovery 93.86%. In 2008-2010, the company bought 10 SLon-2500 magnetic separators to treat such iron ores. In 2010 the first SLon-3000 was applied to processing ilmenite. The magnetite-ilmenite deposit is located in Pan Zhi Hua, Si Chuan Province of China. The ore processing flow sheet is: Drum low intensity magnetic separator is used to take out magnetite, and then the SLon-3000 is used to recover ilmenite for roughing. The mags of the SLon-3000 are further cleaned by flotation. The SLon-3000 average operational results are: feed grade 9.52%TiO2, mags grade 17.43%TiO2, mags mass ratio 41.01%, TiO2 recovery 75.09%, non-mags grade 4.02% TiO2, non-mags mass ratio 58.99%. SLon magnetic separators Applied to treat 0-5mm limonite: The feed of SLon magnetic separator is usually 0-2 mm which needs to be ground by ball mill. As many Chinese iron ores are poor grades, if we can throw part of tails before grinding, the grinding cost will be greatly reduced. In 2010, a SLon-1500 and a SLon-2000 were specially built to treat 0-5 mm limonite. The feed grade is 26.51%Fe, mags grade 53.20%Fe, iron recovery 64.26, and tails grade 13.66% Fe. SLon-2500 applied to purify quartz. In 2009, a SLon-2500 magnetic separator was applied to purify quartz in Shan Xi province. Its feed is 0-1mm quartz which contains 0.15%-0.25%Fe2O3, the designed non-mags grade need to be less 0.08% Fe2O3. The production results of SLon-2500 non-mags are 0.05-0.06% Fe2O3, much better than the designed data. SLon applied in Si Jia Ying Iron Mine to recover hematite. Si Jia Ying is a big oxidized iron mine located in He Bei Province of China. In 2005-2010, a plant annually treating 10 million tons of oxidized iron ore was built in which 39 SLon magnetic separators are applied. The total flow sheet results are: Feed grade 30.44%Fe, iron concentrate grade 66%Fe, iron recovery 80%Fe, tails grade 9.65Fe%. SLon applied to recover specularite. Li Lou Iron Mine in An Hui Province of China built a plant annually processing 5 million tons of iron ore in 2010-2011. 25 SLon-2000 magnetic separators are applied to recover specularite. The total flow sheet results are: Feed grade 31.65%Fe, iron concentrate grade 65%Fe, iron recovery 80%Fe, tails grade 10.37%Fe. SLon applied in Da Hong Shan Iron Mine. Da Hong Shan Iron Mine is located in Yun Nan province of China. It treats 4.5 million tons of oxidized iron ore annually. 15 SLon-2000 magnetic separators are applied to recover hematite. The total flow sheet results are: Feed grade 35.61%Fe, iron concentrate grade 64.95%Fe, iron recovery 74.08%Fe, tails grade 15.55%. Keywords: SLon magnetic separator, iron ore, ilmenite, quartz, beneficiation

Sep 1, 2012

As a kind of collector, Xanthates are generally used to make sulfide minerals hydrophobic in flotation process. Xanthate adsorption on a galena surface has been widely studied experimentally. In this paper, DFT methods were employed to investigate the local adsorption interactions about the collectors,such as ethyl xanthate (CH3CH2OCS2?, EO) and ethyl trithiocarbonate (CH3CH2SCS2?, ES), absorbing on two different PbS clusters. From the results, it can be easily found that, on the edge or at the apex, both collectors, with two S atoms bidentate coordinating on the clusters, have surprising interaction energies, while on the surface, its interaction is relatively weak in the form of monodentate ligand. NBO analysis results reveal that there is at least a covalence bond with sulfur atom about 10% and lead atom about 90% when the absorbed lead is on the lattice edge or at apex, but, if the absorbed lead is on the lattice surface, no covalence band would be found. Meanwhile, the S-Pb bond, formed by the absorbed Xanthate and galena lattice, seems to have much more covalence characteristic than that formed in the PbS lattice inner. Furthermore, those data also imply that the difference of the collecting effect between the EO and the ES may be not notable, because of the similar distance and the interaction energy for the same interaction mode.

Jan 1, 2014

By O. Jerez, A. Novoselov, L. Gutiérrez, J. Morales, U. Kelm

"In Chile, the evaluation to reprocess tailings for elements other than the traditional Cu, Mo, Au, and Ag, as well as projects to implement long-term monitoring of mining residue sites are key elements of the government’s roadmap laid out for the mining industry for the next two decades. Characterization routines for tailings and mining residues in general have to be adapted from traditional ore and gangue mineral and micro-chemical studies. This contribution summarizes key aspects for the regional mining industry for a basic characterization of tailings with emphasis on small- to medium-size operations with limited in-house facilities and funds to carry out extensive characterization programs. The oldest tailings in Chile were deposited almost a century ago; this fact gives importance to the recovery of past ore /gangue feed information, process circuits and changes (e.g. acid to alkaline flotation), process water provenance and recovery, meteorological registers, and routines of filling a tailings impoundment. Basic characterization should include X-ray fluorescence spectrometry combined with laser diffraction (LD) granulometry followed by X-ray diffraction (XRD), optical microscopy (OM) and automated mineral analysis (AMA) on a reduced set of samples identified by hierarchical cluster analysis. For this detailed stage, only coarse tailings are recommended for direct a study by microscopy and automated mineralogy (P80 >100 µm); for fine tailings (P80 ~30 µm) a combination of XRD and deposit type adapted sequential extraction are more informative options. In particular, for XRD of clay phases, losses of crystallinity may result in deviation of spectra from standard reference phases due to prolonged storage. To monitor surface alteration, scanning electron microscopy can be complemented by Raman spectroscopy to detect residual reagents on mineral surfaces. For reactivity modeling BET measurements are essential."

Jan 1, 2018