Search Documents

By Hideki Yamamoto, Norihiro Murayama, Junji Shibata

"Hydrothermal syntheses of zeolite from coal fly ash were carried out by using various alkali sources. NaOH, Na2CO3, KOH, K2CO3 and their mixture were applied for an alkali source of zeolite synthesis. The various physical properties of the reaction product, such as the kind of zeolite crystal, cation exchange property, surface texture and so on, was investigated through the zeolitization reaction from fly ash. The mechanism of zeolitization reaction was considered from these results.Zeolite P(NaP), hydroxysodalite(HS) and chabazite(K-CHA) are synthesized as zeolite species, when fly ash hydrothermally reacts in various alkali solutions at 393K. The crystal structure of the products obtained in NaOH solutions for 3h changes from NaP to HS with increasing NaOH concentration. K-CHA formation in KOH solutions needs 10h of reaction time, which is longer than that of NaP or HS.Dissolution, condensation and crystallization steps exist in the zeolitization reaction from fly ash, and the particle surface of products remarkably changes in each step. The fly ash is spherical particles and the surface is smooth(Fig.1(a)). The dissolution of fly ash occurs in the heating process until 393K, and the particle surface changes like unevenness(Fig.1(b)). In case of NaP, the condensation of aluminosilicate ions takes place at 373-393K, and the amorphous aluminosilicate is deposit on the unreacted fly ash(Fig.1(c)). The crystallization of NaP already begins to occur at 393K and the surface is covered with fine zeolite crystals for 24h(Fig.1(d))."

Jan 1, 2003

By P. A. Harvey

Previous studies have reported that inorganic electrolytes can enhance floatability of coal. The research has shown that the enhancement, if any, is highly dependent on changes in solution pH, type of electrolyte, and electrolyte concentration. The reasons for this are still not clear. In this study the floatability of coal particles in mono and divalent salt solutions was investigated. The zeta potential and hydrophobicity of the coal was measured experimentally, and a modified Hallimond tube was used to determine the floatability of coal particles by single bubbles, where the collision efficiency was equal to unity. The experimental information was used in conjunction with the Hogg-Healy-Fuerstenau equation to quantify the electrical double layer interaction. It was found that for low electrolyte concentration (less than 0.1 M) solutions the flotation recovery of coal particles was less than that for distilled water, and decreased with increase in concentration. Conversely, at electrolyte concentrations above 0.1 M, flotation recovery increased with increasing concentration (Figure 1). Both of these results are consistent with previous observations, but are inconsistent with expectations when considering the possible influence of electrical double layer interaction. Modelling of the system indicates that the electrical double layer is compressed with increasing electrolyte concentration, resulting in an increase in flotation recovery due to a diminishing of the (electrical double layer) repulsion between the bubble and the coal particles. Moreover, for electrolyte concentrations above about 0.1 M the electrical double layer is completely depressed and would have little further influence, if any, on the flotation process. Therefore, the electrical double layer interaction is not the principal determining factor for the flotation of coal in electrolyte solutions.

Jan 1, 2003

By A. Ekrem Yüce, Gülay Bulut, Feridun Boylu, Vecihi Gürkan, Istanbul Technical University, H. MustafaTarkan

"Nickel sulphide ores subjected to this investigation were taken from Orhaneli district where widespread chromite mineralisation can be occurred. Significant amounts of magnetite and chromite have been existed in the ore together with sulphide and oxide type nickel minerals. Ore sample is constituted about 70% magnetite, 15% sulphide minerals, 5% chromite and iron oxides as well as 10% gangue minerals.According to the chemical analysis results, the representative ore sample contains 1.32% Ni, 10.8% SiO2, 78.4% Fe2O3, 1.3 g/t Ag and 1.0 g/t Au. Mineralogical examinations showed that pentlandite (Fe, Ni)9S8, violarite (Ni, Fe)3S4, millerite NiS and asbolane (Co, Ni)MnO2.(OH)2.1-2H2O were the main nickel minerals and magnetite, chromite, chromium spinals, pyrite, pyrhotite, chalcopyrite, cubanite, goethite, hematite, limonite, rutile, chlorite, talc and serpentine group minerals as associated minerals.The aim of this investigation was to produce valuable nickel concentrates by using gravity separation, magnetic separation and flotation methods. As a results of laboratory scale studies, alternative flow sheets for the production of nickel sulphide concentrate were developed. The related experimental results are given in Table 1."

Jan 1, 2003

By M. M. Fan

In Florida?s phosphate industrial practice, the most favorable upper size limit of froth flotation is 1.18 mm which corresponds to particle weight of about 2.8 mg. Conventional froth flotation is not efficient in upgrading coarse particles (+0.425-1.18 mm). A limited number of studies have been devoted to understanding and improving coarse particle flotation. We have shown that the coarse particle flotation performance can be significantly improved by the presence of picobubbles generated by hydrodynamic cavitation. In this study, the size of picobubbles produced under certain hydrodynamic conditions was measured by a laser particle size analyzer. A size-by-size flotation performance analysis of coarse phosphate froth flotation in the presence of picobubbles is conducted in terms of flotation kinetics, selectivity and recovery. It was found that picobubbles doubled the flota-tion rate, increased the P2O5 recovery more significantly for +0.85-1.18 mm particles than +0.425- 0.6 mm and +0.60-0.85 mm particles. At a given acid insolubles (A.I.) rejection, the presence of picobubbles increased the P2O5 recovery by up to about 25%.

Jan 1, 2014

By Tohru Kamo, Shigeyuki Katano, Hideki Nakagome, Maiko Adachi, Shingo Nakamura, Kaneshi Taniguchi, Zar Zar Hlaing, Takaaki Wajima

Tantalum capacitor is a small-sized and has large capacity, and is indispensable for electric equipment. The demand increases year by year, and a quite large number of used tantalum capacitors is generated. Recovery of tantalum from tantalum condenser is recently important since production of tantalum have not been stable for the price and the quality. However, recovery of tantalum from tantalum-condenser is difficult since tantalum parts strongly cover with the flame retardant resin made of halogenated compound (mold resin). This research investigated recovery of tantalum parts from tantalum condenser using steam gasification with mixed molten carbonate. Mixed molten carbonate (Na2CO3:K2CO3:Li2CO3 = 1:1:1) (3 g) put into the reactor, and heated with electric furnace while flowing nitrogen (160 mL/min) and steam (1 mL/min) warmed by heater. After heating to setting temperature (450 - 650 oC), tantalum condenser (3 g) was put into the reactor, heated for 5-10 min, and then cooled to room temperature to recover the reacted capacitor by filtration after treating with distilled water. At relatively low temperature (550 oC) heating for 10 min, mold resin can be decomposed by using steam gasification with mixed molten carbonate, in comparison with using pyrolysis and steam gasification without carbonate, and decomposition reaction occurred over 500 oC by using steam gasification with mixed carbonate. Recovery of tantalum parts from capacitor is successful using steam gasification with mixed molten carbonate at 530 oC for 5 min, due to the effective decomposition and removal of mold resin from capacitor. Furthermore, most halogen gas generated from decomposition of mold resin can be trapped in molten carbonate not to exhaust halogen gas. These results suggested that recovery process of tantalum parts from used condenser using steam gasification with mixed molten carbonate is expected as a feasible way to recycle the rare metal in electric equipment.

Jan 1, 2014

By M. L. Torem, R. H. Rojas, A. G. Merma

"Fine particle recovery by conventional flotation processes is very low mainly due to the low probability of bubble/particle collision and adhesion. In order to solve the problem of low particle recovery, several flotation technologies have been developed to increase bubble/particle collision efficiency. Among these technologies, the electroflotation process stands out. This process has advantages in the generation of microbubbles (<100 µm) and in the production of different amounts of hydrogen and oxygen microbubbles. These advantages favorably influence the fine particle floatability, due to the greater probability of particle/bubble collision and adhesion. The electroflotation tests were conducted for a hematite/sodium oleate system in a Partridge-Smith modified electroflotation binary cell of 0.38 L usable volume. The sodium oleate concentration, particle size, pH and current density were evaluated. Satisfactory results in the recovery of hematite were found at pH values of 7, reaching hematite floatability of 99% and 90% with hydrogen and oxygen bubbles, respectively.INTRODUCTIONThe flotation recovery of fine and ultrafine particles is normally very low and is caused by several factors, among them, the low probability of collision and adhesion bubble-particle, the difficulty to overcome the energy barrier (entrainment and entrapment), low selectivity, surface oxidation and mineralogical changes (Schulze et al., 1989; Waters et al., 2008; Shahbazi et al., 2010). This problem can be overcome by decreasing the bubble size or by increasing the apparent particle size. However, it is worth noting that the use of small bubbles or micro bubbles also involves some disadvantages such as their low momentum resulting in a slower process comparing with conventional flotation. Electroflotation is an attractive alternative for treating fine particles with small bubbles less than 100 µm, generated by the electrolysis of water. Electroflotation is one of the variants of the flotation process, where the gaseous phase is produced by electrolysis of an aqueous solution, generating oxygen and hydrogen bubbles (Sarkar, 2010; Gupta and Ali, 2012). These smaller size bubbles allow the recovery of fine particles by increasing the collision efficiency. This process is versatile and competitive in relation to other techniques such as dissolved air flotation and dispersed air flotation because the electroflotation units are smaller, more compact and require less maintenance and less operating cost than other flotation units (Zouboulis and Matis, 1995,). In addition, the electroflotation process is a clean technique and provides results in a short time, requiring only the investment in the electroflotation cell construction stage and the choice of the electrodes (Ketkar et al., 1991; Sarkar et al., 2010; Sun et al., 2011). In this sense, this study assesses the effect of pH, particle size and sodium oleate concentration on electroflotation of hematite fines."

Jan 1, 2018

By Lokesh K. Thakur, Peter Radziszewski

"For the cases tested (11 mills with 15 operating conditions), the Bond abrasion test steel media wear rate prediction gives an overall error of 73% and a standard deviation of 192.5%. However, total steel media wear in a given mill (ball or SAG) grinding process is a product of three recognised wear mechanisms -- impact, abrasion, and corrosion. A total media wear model can be defined on the assumption that the effect of each wear mechanism can be independently determined which allows for a total media wear model to be defined as the summation of the wear result of each mechanism (eqn. 1). It is assumed that impact and abrasive media wear is a function of the energy dissipated in impact and abrasion as estimated by a DEM charge motion simulation. Corrosive media wear is assumed to be a function of the media surface area present in a mill.The 3 initial tests developed (steel abrasion wheel, corrosion batch mill, impact chamber) coupled with the impact and abrasion energy spectra from a DEM charge motion simulation produced total steel wear rate results for the same cases as the Bond abrasion test giving an overall error of 0% and a standard deviation of 66.1%. However, if one were to consider the general observation that wear is proportional to energy and maintain the assumption that corrosion is proportional to media surface area then one would realize that the total media wear eqn. (1) can be reduced to eqn. (2). As this is a linear equation and one has, for the same mill, media wear and operating data for three different operating cases, one obtains three equations with three unknowns. This defines a simple matrix manipulation to determine the constants k1, k2 and k3. From the previous data set, we had 6 identical mills grinding the same ore but having different worn liner profiles and charge volume which provided the opportunity to average out the ki values over 20 combinations of 3 cases. With the determined ki values, it was possible to determine a second estimate of the contributions of impact, abrasion and corrosion to total media wear giving an overall error of 0% and a standard deviation of 56%."

Jan 1, 2003

By Chuansheng Luo, Qiuyang Hong, Lili Zhang, Dongyun Liang

"The metallogenic rock of a sandstone-type Cu ore is arkose-quartzite as well as siltstone and the cement is composed of argillaceous minerals including sericite, chlorite, etc. and carbonate minerals including calcite, dolomite, etc. A detailed process mineralogy study on this complex copper ore was carried out using MLA combined with traditional research methods. According to the results, there are many types of Cu minerals including copper sulfideminerals, secondary copper sulfideminerals, copper oxideminerals, copper carbonate hydroxide minerals and copper silicate minerals in the ore. Based on the occurrence of Cu, the copper existing as copper sulfide minerals (bornite, chalcopyrite and chalcocite) and copper oxide mineral (malachite) which have a good floatability accounts for 49.28% while the copper (chrysocolla) hard to be recovered by flotation and the copper existing in the cement (sericite, chlorite, psilomelane and limonite) accounts for 48.65%, and the copper existing in the carbonate minerals (calcite and dolomite) accounts for 1.72%. The process mineralogy study indicates that the process "beneficiation combined with hydrometallurgy" should be applied due to the various occurrence of Cu. The abundance of calcite and dolomite is about 12%, so removing these acid-consuming minerals by floatation is an effective way to reduce the acid consumption in the hydrometallurgical process and the lowest Cu loss is 1.72%. So the process "floating copper minerals-floating calcium minerals (calcite and dolomite)-leaching copper from the tailings" is used in the pilot tests. The recovery of floating copper and leaching copper from tailings is 46% and 30% respectively, so the total recovery of copper is 76%. Compared with the original process "leaching copper from crude ore-floating copper from the residue", the total recovery reduces by 1% but the acid consumption of producing per ton of copper decreases from 37t to 12t. The new technology process has a great advantage."

Jan 1, 2014

By Gus Van Weert, Samuel A. Bolorunduro, David B. Dreisinger

"INTRODUCTIONAcid pressure oxidation of high-grade natural acanthite was investigated in the range of 110-150°C and in the sulphate media. High acidity and low pulp density were used to prevent the precipitation of silver.RESULTS AND DISCUSSIONTwo sets of acanthite specimens were obtained from La Valenciana and Ingleterra mines, Mexico. Pressure oxidation tests were conducted on 1 litre scale in a standard 2-litre Parr titanium autoclave.EFFECT OF TEMPERATURE ON THE REACTION OF ACANTHITEThe effect of temperature on the rate of oxidation is presented in Figure 1. The rate of reaction increased with increasing temperature."

Jan 1, 2003

By V. M. Bystritsky, M. G. Sapozhnikov, G. M. Nikitin, A. B. Sadovsky, Yu. N. Rogov

"At present kimberlite ore is processed in crushers or grinding rolls with subsequent grinding in wet mills down to a size of 0.2 mm. The basic disadvantage of the standard diamond processing technology is that crushing kimberlite ore can damage the most valuable large diamonds of few carats. Tagged neutron method offers a possible solution to this problem. It allows detecting diamond inside kimberlite ore without its disruption. The results of the tests of the neutron separator prototype carried out at the Lomonosov processing factory of PJSC Severalmaz are discussed. The possibility to detect the diamond in the rock whose size is 10 times larger than the size of the diamond is demonstrated.INTRODUCTION At present standard diamond processing technology implies disintegration of kimberlite ore in crushers or grinding rolls down to a size of 0.2 mm. It inevitably leads to high probability that large and most valuable diamonds could be damaged. The fraction of diamonds which lost integrity in the process of ore enrichment could be as large as 35-65% [1]. Tagged neutron method (TNM) [2] offers a possible solution to this problem. It allows detecting diamond inside kimberlite ore without its disruption. The main idea of the TNM is irradiation of an object by fast 14.1 MeV neutrons from binary nuclear reaction d + 3H ?4He + n (1) and detecting (tagging) the 4He (a-particle) that accompanies neutron. That gives possibility to determine direction of the neutron momentum. Those tagged neutrons irradiate kimberlite ore under investigation and produce gamma rays via inelastic scattering reactions with nuclei"

Jan 1, 2018

By Ashok M. Raichur, S. P. Vijayalakshmi

"Recent advances in technology and the growing environmental concern have laid emphasis on the usage of fine clean coal. Coal fines are also generated in large amounts during various coal processing operations and are difficult to be treated, handled and disposed. Since most of the operations use water as the carrying medium, the fines so generated contain lot of moisture. Conventional technique for processing coal fines includes flocculation by a polymeric reagent followed by moisture removal using a rotary drum or a pressure plate filter, which produce a product with more than 30% moisture. Polymeric flocculants though required in small amounts, need high shear mixing for good performance and operate only in a narrow pH range. Moreover they increase the viscosity of the solution by many folds. Hence it becomes imperative to emulate newer methods for efficient fine coal processing. One such method is the novel use of microorganisms in coal processing.The present investigation deals with the utilization of two gram-positive microorganisms, Mycobacterium phlei and Bacillus subtilis, as bio flocculants and dewatering aids in fine coal processing. Preliminary characterization done on J-coal and M.phlei showed that they are negatively charged over most of the pH range. B.subtilis was found to possess positive charge below pH 4.7. The adhesion studies proved the high potential of microorganisms for adsorption to surfaces. Adhesion tests were conducted at various experimental conditions by varying parameters like pH and ionic strength of the suspension. Results obtained showed that adhesion is always higher in the presence of an electrolyte like KNO3 and most of the adhesion takes place in 15 minutes. With change in pH the amount of B.subtilis adhering on to J-coal remained almost constant and for M.phlei it decreased at higher pH values. Increase in ionic strength did not increase the adhesion of bacteria. Flocculation experiments confirmed the ability of the bacteria to act as bio flocculants. It was seen that about 98% of the coal settled in about 2 minutes on the addition of bacteria along with the addition of the electrolyte. The electrolyte was found to be indispensable for efficient flocculation of the coal suspension and for the attainment of a clear supernatant after flocculation. Also the optical micrographs revealed the formation of large, tight flocs when the electrolyte is present along with the bacteria. Further, flocculation tests were done in the pH range of 2-10 and the flocculation efficiency was found to be independent of pH."

Jan 1, 2003

By Özcan Y. Gülsoy

Coal beneficiation with optical sorting has not yet been studied in detail. Optical separation of coal from gangue particles as a dry method can be used as an alternative to the other enrichment methods. Developments in optical and pneumatic technology put the optical sorting one step forward by means of applicability of the mechanical sorting to the mineral industry. Because of the inefficient separation performance, dry separation of coal is very limited in industrial applications. Therefore, optical sorting depending on color differences between two minerals can be introduced to coal beneficiation systems. In this study, coal samples obtained from Konya-Ilgin region (Central Anatolia-Turkey) were separated by optical sorter and the results were evaluated. The conventional floatability tests for Ilgin coal are conducted by collecting most of the feed material at 1.3-1.4 g/cm3 density range. Separation of Ilgin coals with heavy medium methods will not be possible because of poor density difference between coal and its impurities. There are important color differences among the floated particles at 1.3-1.4 g/cm3 density range. Therefore, Ilgin coal is subjected to optical sorting in a pilot scale optical sorter. Different size fractions were fed to the optical sorter and then rejected and accepted particles by equipment were analyzed. Ash content of the accepted particles was reduced to 25-35 % and ash in tail increases up to 55-60 % after sorting. Although most of the material floated at low densities, optical sorter separated the feed into two different quality products. This study has the potential to clarify applicability of optical sorting even to non-floatable coals and to provide an important contribution to both industrial applications and literature.

Sep 1, 2012

By Yuriy V. Gulyaev, Galina V. Sedelnikova, Valeriy D. Lunin, Valentin A. Chanturiya, Igor J. Bunin

"In Russia the industrial exploitation of ore deposits is determined as a strategic direction of gold extraction industry development. The majority of gold-containing ores of Russia is referred to category of rebellious ores with 3-5 g/t gold content and is characterized by low factors of gold and silver extraction under cyaniding. The resistance of goldcontaining raw materials under their processing is caused by presence of very fine gold particles less than 0,1-0,01 µm in size, associated with the pyrite and arsenopyrite. Significance of the problem of rational rebellious ores beneficiation and high precious metals extraction is increasing from year to year.Group of scientists from IPKON and IRE, Russian Academy of Sciences, has developed highly effective, powereconomic and ecologically clean method of breaking-up of resistant gold-containing ores and their beneficiation products on the base of using an energy of powerful electromagnetic pulses. For the first time there have been designed laboratory installation for resistant raw materials treatment in dry and wet state (solid/liquid ratio = 5:1) and ground material less than 1-0,5 mm.Mechanisms of powerful electromagnetic pulses action on natural mineral components, including dielectrics (quartz, calcite), semiconductors (sulfides) and metals (gold, silver) have been theoretically accounted. Pulses action parameters and ways of pulses generating have been discussed in different conditions. At tension of electromagnetic field, exceeding the electric strength of processing material, an electric breakdown develops in the mineral matrix of sulfides and dielectrics. Under the series of pulses action the forming of plural breakdown channels occurs, leading to strength loss of material and microcrackes developing. Thus, the action makes it possible for leaching solution to access precious metals particles under cyaniding process. Distinctive changing of pyrite and arsenopyrite surface structures under the influence of powerful electromagnetic pulses is confirmed by studies using optical and scanning electron microscopy."

Jan 1, 2003

By K. Saberyan

Zirconium and hafnium are two important elements in nuclear industries. Zirconium is used in fuel rod for its low neutron absorption. Hafnium should be separated from zirconium, because it has higher neutron absorption cross section. In this research, separation process of the mentioned elements from (Zr+Hf)Cl4 mixture produced in the Zirconium production plant (ZPP) of Iran (Esfahan) was studied employing solvent extraction method in the nitric acid medium by using tributylphosphate (TBP) as solvent, and kerosene as diluent. The effects of nitric acid, sodium nitrate and amount of extractant, zirconium concentration in aqueous phase, phase ratio, agitation time, and mixer agitation rate were investigated on the separation process. The process was optimized at 5 M nitric acid, 1 M sodium nitrate, 60% (v/v) TBP. The optimum values for phase ratio, agitation time and agitation rate were 1.5 min and 500 rpm respectively. In this condition, the zirconium extraction efficiency, and separation factor were 65.1% and 205.59, respectively. Finally, we accessed to nuclear grade in this research.

Jan 1, 2014

By H. U. R. Kattentidt, W. L. Dalmijn, T. P. R. de Jong

"Research at Delft University aims to develop systems for automatic inspection and sorting of bulk solids which can be applied in the mineral processing and recycling industry. A recent development includes an automatic sorter based on airport X-ray inspection technology. It is designed for continuous inspection and sorting of 5 - 150 mm solids and has as objective a cost effective and high capacity on-line inspection and sorting.Dual energy X-ray transmission imaging provides instantaneous data about particle dimensions and the atomic number distribution. The system provides particle thickness and average atomic number on a pixel level at scanning speeds between 250 and 500 lines / second. With existing X-ray components inspection speeds between 0.5 and 2 m/s at approximately 1-meter inspection width and between 1.5*1.5 and 5*5 mm2 sensor resolution can be achieved.Imaging algorithms that were developed by Delft University for applications in recycling, waste cleaning and other applications acquire shape, size distribution and composition data. Currently on-line processing of a product at a rate of around 200 particles per second is possible using a standard PC. Experiments with a demonstration X-ray unit indicated good potential for various applications in solids processing. They include continuous inspection of organic content, sulphur, chlorine, ash, and metal distribution. It is applicable for coal cleaning, ore sorting, industrial minerals, and various applications within waste cleaning and recycling. Dual energy X-ray transmission fundamentals and recent progress in system development and applications are presented."

Jan 1, 2003

The Arctic is a region of special economic, geopolitical, research, socio-ethnic, and defense interests of both Russia and other countries of the Arctic zone. Introduction of innovation technologies at ore-processing factories is a direct responsibility of the state and this problem should be solved on the basis of coordination of interests of different stakeholders. The task of elaboration of scientific principles of rational state regulation in the North is very topical. Innovations require considerable investments first of all from private capital. However as an investment object innovations are not attractive for investors as they require large expenditures for long-term projects, and they are connected to high risks because market incentives form striving to get quick profits of private companies and result in a certain behaviour strategy while innovations need ?long money?. Under such conditions without state regulation of investment and innovation activities development of the mining sector in the Arctic practically has no prospects. At innovation development of mining enterprises economic growth is provided at the expense of active state innovation activities. The elaborated strategy of ore-processing enterprises should correspond to the modern paradigm of the ore-processing industry development which is not only for extraction of minerals but also for multi-profile structure having comprehensive use of the resources on the rational basis intended for rational complex utilization of mineral resources of the AZR which by the definition includes maximally full use of the whole aggregate of resources on the economically rational basis with obligatory environmental with resource reproductive and socio-economic functions and deterrents. The main principle of creation of innovation technologies is to obtain more products of higher quality with minimal costs. This allows increasing ?productivity of the resources? several times. This principle makes increasing productivity of the resources the most important and in this case efficiency of use of the resources brings extra profits at the expense of lack of new costs such as payment for protection and utilization of wastes. According to the economic theory only ratio between demand and supply is able to fix optimal proportions in economy and to give necessary signals for investment activities of mining enterprises. In this context market for minerals and increase of mineral resources productivity do not create incentives for investment activities without which neither sustainable economic growth nor solution of macroeconomic tasks are possible. Nevertheless countries should not reject this idea in spite of economic efficiency of the enterprises. Extraction degree of useful components and especially oil in the Arctic zone is one of the lowest in the world. This can lead to crisis of oil industry and other mining sectors. The reason for that is lack of a state policy of realization of innovation technologies in the mining sector in the Arctic.

Jan 1, 2014

By lves Matiolo, Jorge Rubio, Carlos Perez Guerrero, Denise G. Nunes, Fabiano Capponi

The problem (very old) of processing by flotation, the fine (“F”, 38-13 µm) and ultrafines (“UF”, < 13 µm) mineral particles continues to be a major technical challenge in the area of mineral processing. Many different processes have been proposed over the last three decades but, unfortunately, most of them have not found practical applications yet. This paper describes some advances in flotation research in fines (“F”, 38-13 µm) and ultrafines (“UF”, < 13 µm) mineral recovery by two different techniques. Extender flotation (EF) and flotation with bubbles with a wide size distribution-SB of copper sulphide ore fines (1 % Cu) were compared with a “standardised” (STD) mill laboratory procedure. Comparative evaluation was made through concentrate grade and recovery (size by size results included), “true” flotation recoveries and process kinetics. Copper porphyry samples, containing about 1/3 of the mass and about 37 % of the total copper content in the fines and ultrafines fractions were used. In the EF tests diesel-in-water emulsions were used as an extra reagent, added after the collector and frother addition. In SB tests, drawing air through an aspiration nozzle, directly in the pulp, generated bubbles sized about 50-200 µm. Both techniques yielded higher metallurgical efficiencies than the mill standard but better results were obtained with the extender flotation, with emulsified diesel oil (90 gt-1). Concentrate recoveries were of the order of 85-90 % (84 % in standard conditions), 14-17 % Cu grade (15 % Cu in the standard) and 3.5-4.5 min-1 for the Klimpel rate constant (3 min-1 in the standard). Size by size and true flotation results proved that metallurgical and kinetic gains, obtained with the two techniques, might be attributed to fines and ultrafines enhancement. Data obtained are discussed in terms of physical and physicochemical parameters related to aggregation and capture (of particles by bubbles) phenomena and the practical potential of these techniques are envisaged. The following figure shows size-by-size copper recoveries results, after classification of produced concentrates and tailings using micro-sieves. Results clearly show that flotation of the F and UF fractions is highly improved with injection of small bubbles (SB) and with the addition of an extender collector. It is believed that the techniques presented here will establish shortly a new basis for the flotation enhancement of the F and UF, aimed at solving a very old problem. This work is being continued, now at pilot plant scale, and results will be published en the near future.

Jan 1, 2003

By Sonia Helle, Ursula E. D. Kelm

"From a metallurgical point of view, acid leaching of oxide zone copper ore is considered in the first place in terms of ore grade, whole rock mineralogy, rock granulometry, crushed aggregate size distribution, porosity, permeability and corresponding fluid flow characteristics. Despite exhaustive physicochemical and general mineralogical characterization, drops in copper recovery occur and are often attributed to and “unquantified mineralogical misbehaviour” of the gangue phases. This study establishes an experimental link to monitor and quantify the chemical interaction of chrysocolla, malachite and atacamite with reactive gangue phases.Laboratory-scale sulphuric acid (15%) leaching in small columns is carried out using a synthetic rock composed of 57% quartz, 1% ore phase, and 42% reactive gangue. Gangue phases were selected to represent mineralogy found in argillic, advanced argillic, and propylitic alteration zones. Exotic copper ores of Codelco Norte (in particular Mina Sur) served as model for the modal distribution of mineral phases. Natural reactive gangue phases (<200 Tyler mesh) were chosen as pure as possible: Saz-1 and Swy-1 montmorillonites, KGa-1B and KGa-2 kaolinites (all Clay Mineral Society, USA, Source Clays) Nau-2 nontronite, Imt-1 illite (both Clay Mineral Society Special Clays) and Chilean mordenite, laumontite and bentonite. Ore phases are: mineraloid chrysocolla from Radomiro Tomic (Codelco Norte), reagent grade malachite and a purpose synthesized atacamite-paratacamite mixture. Complete chemical, physicochemical and mineralogical characterizations were carried out for ore and gangue phases.The following observations hold for samples with and without mineralization: Smectite-rich gangue increased up to 75% in volume. Once wet, air-filled vesicles formed due to the rapid sealing effect of overlying smectite in the column. No volume change occurred for illite, mordenite and kaolinite gangues. For kaolinite mixtures acid puddles formed on top of the column during initial leaching due to the delamination and barrier formation of this phyllosilicate. Fluid recovery was <60% for expandable phases and reached up to 80% for non-expandable mixtures. These observations confirm the very low extractions obtained in ore with a combined smectite – kaolinite gangue for Mina Sur. The most important mineralogical changes observed in the solid residues are: reduction of basal smectite phase reflections (XRD), and slight loss of illite intensities. This is also reflected in the major element composition of the residues, which demonstrate a loss of Mg, Mn, Ca, Na, K followed by Fe, Al and Si; with their proportions depending on the starting materials. Furthermore, alunogen and meta-alunogen formed, with related phases coquimbite (illite) and godichite (nontronite) also depending on gangue mineral chemistry. For laumontite samples, meta-alunogen and alunogen precipitated from the leachate."

Jan 1, 2003

By Kobus (J. J. ) Rossouw, P. Chris Pistorius, Johannes Sono

"Different coal properties are important in SL/RN (coal-based rotary kiln) direct reduction of iron ore, and in electrical smelting of prereduced iron ore. Laboratory simulation was used to evaluate two candidate coals, which were similar in volatile content and rank, but differed in reactive maceral content. The tests served to evaluate both the reduction rate (during direct reduction) and the dissolution rate of carbon from the coal into an iron bath.Reduction rates of mixtures of magnetite and devolatilised coal were assessed isothermally, using samples of 55 grams. The off-gas analysis was used to follow the extent of reduction. Results are shown in Figure 1 a). Coal B was expected to be more reactive, based on its higher content of reactive macerals (77%, compared with 61% for Coal A). In line with this, Figure 1 a) does show a higher reduction rate with this coal. However, increasing the reduction temperature increases the reduction rate substantially,especially for the less-reactive Coal A.For the dissolution experiments, samples (mass: 250 g) were melted in an alumina crucible (under a nitrogen atmosphere), to give a starting composition around 1%C. When the desired temperature was reached, 25 g of char was added on top of the melt, through a feeding port. Results are shown in Figure 1 b). The more-reactive Coal B was less crystalline (the graphite crystallite size estimated from X-ray diffraction was 4.6Å, compared with 11.4Å for Coal A). This is associated with a lower dissolution rate in iron."

Jan 1, 2003

By John A. Herbst

Professor A.M. Gaudin and his students at MIT were dedicated to understanding the fundamentals of mineral processing and as a consequence were constantly searching for better quantatative descriptions of size reduction, liberation and mineral separations. I have had the good fortune of meeting Professor Gaudin and working with many the modeling pioneers who followed him. I have observed first hand the refinement of mineral processing models as they increased in realisticness moving up the steps of the pyramid (see figure below) from pure empiricism to the current pinacle of physics based models. During this journey our industry benefited significanbtly as model prediction errors were reduced from ± 20% to ± 1%. Unit operation and plant simulations improved in accuracy and speed of calculations.

Sep 1, 2012