Search Documents

By Chu E. Ho, Alfredas Daugiala, Nicola Ebanks

"The construction of an ancillary structure for the new Second Avenue Subway Line in Manhattan, New York City involved a deep excavation in highly variable rock conditions adjacent to a fragile masonry building. The maximum difference between the lowest and highest rock elevations was about 30 feet, which posed a problem for the installation of secant piles that formed the supporting retaining wall for the excavation. At certain areas, the rock levels were higher than the top of the invert slab of the ancillary structure. To avoid disturbance to the adjacent fragile building, the secant piles were fully cased for drilling through the overburden soils and the rock sockets were formed using non-vibratory technique. This paper discusses the design and installation details of the secant pile wall and the contingency measures that were considered to mitigate the highly variable rock conditions. Monitoring of the adjacent fragile building showed that impact of pile installation were controlled within tolerable limits and safety of the building was not compromised.INTRODUCTIONThe 96th Street Station forms part of the newly constructed Second Avenue Subway Line on the East side of Manhattan Island, New York City (Figure 1). During construction of this station, several deep excavations were carried out adjacent to existing fragile buildings (Arksman et al. 2012, Grigson et al. 2016). These fragile buildings were typically four to five stories high, with a single rubble wall basement supported on timber piles or seated directly on the fill. The timber piles were often found to be in a poor condition and connections to the footings were compromised due to rotting of the timber within the zone of water table fluctuation. Several of these fragile buildings had to be strengthened and underpinned to improve the stability of the structures prior to commencement of excavation for the new subway station box (Trabold et al. 2012, Ho and Pena-Iguaran, 2013). The situation was most challenging at Ancillary Buildings 1 and 2 located at 93rd and 97th Street respectively, where secant pile walls were located merely 2 feet away from the adjacent property line, due to architectural space constraints. While mitigation of excavation induced ground movements can be controlled by the adoption of a stiff excavation support system, a more concerning factor was the uncertainty associated with the impact of the secant pile wall installation on the stability of the existing fragile buildings. This was particularly difficult at Ancillary 1 where the secant piles encountered highly variable rock levels that intruded into the excavation space. The following sections discuss the design and installation of the secant pile wall and contingency measures that were considered at Ancillary 1."

Jan 1, 2016

By Kozo Takeda, Arashi Shimano

"Dry Jet Mixing (DJM) method as the representative deep mixing technique has been demonstrating best practice on ground mitigation works coping with complicated soil condition and limited site space. This technique plays an important role in many projects to stabilize soft ground involving troubles like sliding failure, settlement, bearing capacity etc. Serious disasters caused larger earthquakes make great demand on the application of deep soil mixing these days. Special design and alignment of deep soil mixing has been established against to liquefaction and serious failure due to liquefaction. In this paper, representative example of liquefaction mitigation by DJM method is summarized. The paper also present result of surveillance of sites installed DJM col umns after attack by Tohoku Pacific Ocean Earthquake. Performance of DJM columns suffered the earthquake is demonstrated at several sites even with conventional column alignment.INTRODUCTIONThe DJM method is a representative deep soil mixing technique of dry mixing manner in Japan. DJM can successfully install soil mixing columns trough automatically controlled binder injection based on pneumatic feeding theory and cumulative experiences.This method was joint-developed in 1978 by private organization under initiative of the Public Works Research Institute of the Ministry of Construction as the optimum method for improving the Japanese soft ground. Figure 1 shows full view of the DJM construction system. Figure 2 illustrates DJM working system indicating Binder Feeding Plant side and Mixing Machine side respectively.As typical soil mitigation method, many projects related with rivers and roads and city development has required DJM technology. The total number of the projects applying DJM has exceeded 5,000 with the total treated soil volume more than 32,000,000 m3 by the end of fiscal year 2013."

Jan 1, 2015

By Martin B. Hudson, Andrew K. Cho, Rolff B. Knobel, Les R. Chernauskas, Jonathan L. Ernst

ABSTRACT The Bruce Museum, located in Greenwich, Connecticut, is home to an extensive display of art and natural history exhibitions. A large addition was designed to be constructed adjacent to the museum requiring new spread footings to be installed up to 16.5 feet below the existing foundations. The soil conditions at the site consist of highly variable sand and gravel overlying weathered rock and sound bedrock. The Contract Documents called for traditional foundation underpinning. Traditional underpinning techniques, however, presented two major challenges on this Project; (1) deep underpinning pits would be required involving multiple levels and staging with tieback support and (2) the highly variable soil and bedrock composition and elevations presented uncertainty in the design and construction of the pits. In lieu of traditional underpinning, Geosciences Testing and Research, Inc. (GTR) proposed an “active” soil nail underpinning system. A major reason that the soil nail underpinning option was feasible, related to the fact that the soil nails and facing could be installed slightly in front of the existing footings rather than directly underneath the existing footings. The soil nail wall design involved one to four rows of soil nails with nail positions and wall depth able to be adjusted “on the fly” as excavation progressed depending on the field conditions encountered. To create the “active system,” the soil nails were pre-loaded to mitigate wall deformations that would be associated with a standard passive soil nail wall design. To evaluate the performance of the active soil nail wall and confirm design assumptions, an extensive automated monitoring, on-site testing and inspection program was proposed and executed by GTR to monitor deformations of the wall and the museum in real-time, evaluate and confirm bedrock and soil bond stresses and ensure that each soil nail was pre-loaded and locked off. Careful analysis, planning, and use of the observational method illustrates the importance of collaboration between design and construction personnel and applying engineering judgement throughout construction. The use of the observational method includes the potential for modifying design based on conditions observed. This paper presents a unique case study of the “active” soil nail underpinning system to support and protect sensitive structures, close collaboration between design and construction facilitated by real-time deformation monitoring, and its successful application as a safe and cost-effective alternative to traditional underpinning.

Oct 1, 2022

By Alexander Filotti, Richard Kalson

"1. INTRODUCTION- WHAT IS P3 OR PPP ?The Public Private Partnership (PPP or 3P) is a project delivery scheme based on the government providing land and/or a concession agreement, and on a private entity providing the design, construction, financing, operation and maintenance of the project for an extensive duration of time (up to thirty years). At the end of the operation-maintenance period, the project is turned over to the public entity, which fully owns the project at all times. While there are many PPP delivery schemes used around the world, for the present paper, we are going to analyze the impact of the Design-Build-Finance-Operate-Maintain (DBFOM) scheme on the deep foundation specialty subcontractor. There are couple of reasons that the PPP delivery system started to be used and implemented not only by developed nations (e.g. United Kingdom, USA etc.), but also by the International Development Bank for delivering major infrastructure projects in developing nations. From the point of view of government agencies, some of the reasons to use PPP are the following:??The primary use of private capital in an era where borrowing and/or supplemental taxation represents too much of a political risk. Budget deficits and taxation limits are extremely hot topics in every election (national or local) and the level of education of the electorate in this area is making it more and more difficult for politicians to use borrowed funds and additional taxation finance sources for public projects. At the same time, we see an increase in the social expenditures of the government in parallel with a needed increase in expenditures on infrastructure due to aging and neglect.??Bundling the construction risks with the operational and maintenance risks naturally pushes the private entity to increase the level of innovation and communications in the primary phase ( the construction phase) in order to develop future process based upon the innovation and communications utilized in the operation and maintenance phase of the project. This is true if contractual incentives are properly structured because “all revolves around incentives. In a world of ‘incomplete’ contracts, where it is difficult to foresee and contract about uncertain future events, it is important to get the incentive structure right” (Grimsey and Lewis, 2004).??The transfer of very expensive risks such as differing site conditions, schedule, design, construction, maintenance and operation costs from the public authority to the private entity.??The timespan of development and construction of a PPP project is usually shorter than the traditional procurement process (e.g. “ the I-595 P3 provided capacity improvements fifteen years sooner than a conventional plan would have offered. In Maryland, an innovative expansion of the Seagirt Marine Terminal in the Port of Baltimore was completed two years ahead of schedule due to the P3 model. As a result, the Port of Baltimore is only the second port on the US East Coast to have unrestricted access to both a fully functioning 50-foot channel and 50-foot berth.”)"

Jan 1, 2017

By James N. Mure

The paper describes the design development and construction of bored piles at Pindersfield Hospital, Wakefield, U.K. The piles were of monopile type. Monopile is the term used to describe piles which are constructed without pile caps so that the superstructure columns bear directly on the pile top. Pile geotechnical design was developed from the Site Investigation data and testing of two preliminary piles. Final design philosophy is described. Pile structural design was developed from the loadings applied by the superstructure, and the requirements, tolerances and limitations of monopile construction techniques. Construction was closely controlled in order to achieve a ?right first time? result. The conclusion gives a critique of the system and its value.

Jan 1, 2008

By Jeffrey C. Evans, Daniel G. Ruffing, Hejintao Huang

Soil-bentonite slurry trench cutoff walls are the most common type of vertical cutoff wall used in the US for seepage control and for passive control of contaminant migration at environmental sites. Design considerations are often limited to constructability considerations and a target hydraulic conductivity. With design-build contracts common, the backfill design is often left to the contractor. As a barrier soil, the hydraulic conductivity of bentonite slurry wall backfill is typically required to be equal to or below 1x10-7cm/s. The importance of stress state upon the hydraulic conductivity as well as the expected stresses are both established in the literature. Grain size distribution of the base soil and bentonite content both affect compressibility and hydraulic conductivity. This paper describes the results of studies undertaken to evaluate the interrelationships between compressibility, hydraulic conductivity, grain size distribution, and bentonite content. Three base soils were used representing a range of soils found on typical construction projects. Using these base soils, mixtures containing a range of dry bentonite contents from 0% to 5% were prepared to a slump consistent with field practice. The compressibility and hydraulic conductivity were measured in consolidometers adapted for falling head permeability tests at the end of each load increment. These experiments yielded the relationship between effective stress and hydraulic conductivity as well as consolidation characteristics including time rate of consolidation and coefficients of compressibility. The experimental results are then used to indirectly evaluate stress development and to assess the time needed for consolidation. The findings show a substantial decrease in hydraulic conductivity as effective stress increases, regardless of base soil type and dry bentonite content, a relative insensitivity of stress development to backfill compressibility, and a wide range of values for coefficient of consolidation depending upon backfill mixture and stress level.

Jan 1, 2016

By Jewels Stover, Charles A. Luxford

Oklahoma City is undergoing a replacement program for an existing 66in (1.675m) water pipeline that conveys raw water from Atoka Reservoir to the City. This pipeline currently crosses the Canadian River on elevated piers and is subject to flood hazards. To replace the existing pipeline and mitigate flood damage concerns, two parallel microtunnels will be constructed below the river channel. Access is from construction shafts located near the midpoint of the tunnels; opposing drives are launched from each shaft. This geometry dictated shafts of significant depth – exceeding 120 ft. (37m). To accommodate the casing pipe segments and microtunneling machines, a minimum shaft diameter of approximately 34 ft. (10.4m) was required. Due to the difficult geologic setting, a reinforced secant pile compression ring is specified by contract in the top 70 ft. (21.3m) of these construction shafts to provide a very low permeability support system.

Sep 8, 2021

By Anjana C. P, K. Ranga Swamy

The hilly regions of Kerala are severely affected by excess rainfall, causing tremendous damage due to landslides and slope failures. It is necessary to strengthen the existing slope profiles to prevent such disasters and avoid their risk to human lives and civil infrastructures. This paper studies the effect of micro pile to reinforce the slopes in Idukki district of Kerala, where slope failures are frequent. Three-dimensional slope stability analysis is carried out on slopes from the Idukki to obtain safety factor values using the MIDAS GTS NX program. The slope is fully saturated herein by taking the model's piezometric surface at the ground level to simulate high rainfall intensity. The critical slopes are then modelled with micro piles to analyze their effectiveness in improving the stability under static conditions. Different micro pile arrangements are considered, and a series of slope stability analyses have been carried out to obtain the optimum configuration with the required safety factor. The FOS values increased by more than 50% with micro piles for all the slopes. The optimum micro pile arrangement obtained for each slope shows that micro pile distribution between the toe and middle of the slope is an effective location for reinforcing slopes.

Sep 1, 2022

By G. Ranjan

The designers and the practicing engineers have started using latest and cost effective techniques of ground improvements which utilise the weak and poor sub-soil deposits efficiently for the civil engineering construction. In the present investigation, a new concept of 'skirted granular piles' has been advocated. An effective method of construction of granular piles as an economical alternative to vibroflot, and the skirt has been developed. The construction technique is based on indigeneous know how which effectively utilises the man-power technology avoiding import of costly equipment suiting to the developing countries. Full scale insitu tests have been carried out at four sites, having different soil conditions, on virgin weak sub-soil, and improved ground by casting plain and skirted granular piles. Effectiveness of different types of skirt has been demonstrated through insitu tests. A simple analytical approach has been proposed to predict the ultimate pile capacity. The predicted values of ultimate capacity have been found to demonstrate a good correspondance. Granular pile behaviour in terms of pile depth, diameter, spacing and stress deformation characteristics of the improved ground have been discussed. A significant improvement in ultimate capacity in improved ground has been noted. This is further augmented when granular pile group is skirted.

Jan 1, 2010

By Cory McElprang, Enamul Hoque, Aaron Thomas, Scott A. Jacobs

Crosshole Sonic Logging (CSL) only evaluates concrete on the inside of reinforcing cages leaving the outside unevaluated unless other types of testing are performed such as Perimeter Sonic Logging (PSL). While there have been some reports of PSL testing having accurately identified anomalies (e.g. Samtani et al 2005), experience by Case Foundation Company has indicated otherwise where false positives were determined with subsequent coring. Numerous cases of PSL false positives are presented as well as a study where a shaft was installed with both inside and outside tubes, and CSL and PSL data were compared. To date, there is very limited data published on perimeter sonic logging, or Gamma-Gamma Logging (GGL) with tubes on the exterior of drilled shafts. Several cases will be presented where false positives were experienced where PSL testing was performed. In addition, a direct comparison will also be presented where a shaft was installed with both tubes on the inside and outside where CSL and PSL data is compared. BRIEF HISTORY – CSL TESTING AND TUBES ON INSIDE The general procedure of Crosshole Sonic Logging (CSL) testing includes attaching tubes to the reinforcing cage to be able to send a transmitter in one tube and a receiver in another tube with which a sonic pulse is emitted from the transmitter and received in another tube. The time taken for the sonic pulse to travel between the tubes is measured and compared to expected values for the known distance between the tubes. Any increase in time from expected values indicates the sonic pulse traveled through a media other than homogeneous concrete such as objects in the path (spacer wheels, steel bracing, etc.), tube spacing, or soil inclusions. However, variations in arrival time can also result from differences in concrete density. The tubes have traditionally been placed on the interior of the reinforcing cage which protects them during hoisting and placement of the cage and reduces wave refraction caused by modulus of elasticity differences between steel and concrete. This allows the concrete within the interior of the reinforcing cage to be evaluated, but the concrete outside of the cage is excluded from traditional CSL testing. As a result, alternative integrity testing has been developed to not only provide different ways to evaluate the integrity of drilled shafts but to also address the issue of evaluating the concrete outside of the reinforcing cage. These alternative testing methods include Gamma-Gamma Logging (GGL), Thermal Integrity Profiling (TIP testing) and Perimeter Sonic Logging (PSL) which is similar to CSL testing but instead of the tubes placed inside the reinforcing cage, the tubes are placed on the outside of the reinforcing cage as shown in Fig. 1.

Jan 1, 2019

By R. Radhakrishnan, C. Gunasekaran

"Calicut Bypass Phase-II project included construction of 7 m high embankment over soft compressible clays up to 18 m in thickness. Approx 1.5 km length of road out of a total 5 km length consisted of abandoned paddy fields which were low lying, waterlogged and marshy in nature. On the basis of excellent results achieved in earlier phases of the by-pass construction, ground improvement work by installing pre-fabricated vertical drains (PVD) was undertaken to stabilize the embankment foundation along the weak clay areas prior to road pavement construction to avoid large post construction settlement as well as to improve the lateral stability during and after embankment construction. This project perhaps stands out as one of the highway projects completed within a very short time period of total 18 months including four month long heavy monsoon period, when embankment construction was not possible and construction of two bridges across rivers. All activities including the ground improvement had to be programmed and completed within the shortest time period possible. The paper discusses details of the extensive ground improvement and soil instrumentation carried out for the project and will illustrate how careful planning and execution can reduce the period required for highway projects involving ground improvement.INTRODUCTIONPhase-II construction of Calicut by-pass was undertaken on a priority basis by the State of Kerala in 2014. The main contract was awarded to M/S ULCCS Ltd, Kozhikode, Kerala and the ground improvement work was awarded to M/S Geo-Enviro Engineers P Ltd, as specialist agency to design and execute the work.Soil investigation carried out confirmed thick soft clay deposits below GL in three areas along the road alignment totaling approx 1.5 km in length. These areas were low lying, waterlogged and marshy in nature. Highway embankment had to be constructed up to 7 m in height above existing GL to form the proposed road alignment along these areas. On the basis of excellent results achieved in earlier phases of the by-pass construction using pre-fabricated vertical drains or PVD (R. Radhakrishnan, 2006), ground improvement using PVD had been included in the contract to stabilize the embankment foundation along the weak clay areas prior to highway embankment construction to avoid large post construction settlement as well as to improve lateral stability during its construction."

Jan 1, 2015

By K. Madhusudan Reddy

Pile response under combined uplift and lateral load is very important and it is imperative to evaluate the effect of combined loading and only few studies were reported on pile behavior under combined uplift and lateral loads. Model pile made-up of aluminum having an outer and inner diameter of 25.4 mm and 19.4 mm respectively is used. Dimensions of the model steel tank are fixed as 1.0 m x1.0 m x 1.2 m (depth) to avoid the boundary effects under combined lateral and uplift loads. Experiments were carried out on single piles at isolated uplift, isolated lateral loading and combined lateral and uplift loading, embedded in sandy soil. Results indicate that load?deflection behavior is nonlinear for isolated uplift and lateral load tests as well as in case of combined loadings. It is also observed that the behavior of piles under isolated loadings is substantially different when compared to combined loading.

By Musbah A. Hasan, Ahmed M. Nasr, Fauzi Jarushi

Many transmission towers, high-rise buildings and bridges are supported by piles. These structures may be subjected to large lateral loads. Therefore, experimental investigations on model piles under lateral loads were conducted in uniform dry sand. Small-scale model tests were carried out considering the influence of pile length, pile diameter, sand density, roughness of pile surface and vertical load on the lateral resistance of a pile. Furthermore, the effect of pile load eccentricity (e/L) on the ultimate lateral resistance was studied. Investigations, of the influence of various parameters on the magnitude of the coefficient of subgrade reaction (nh), were also performed. It was found that the lateral load capacity of piles increases with increase in pile length, pile diameter, pile surface roughness and increase in the sand density. The results also showed that the coefficient of horizontal modulus of subgrade reaction, (nh), decreases with deflection increase. From the results, the coefficient of subgrade reaction for a smooth pile embedded in medium dense sand would decrease by (134%) when the lateral pile head deflection (yg) changes from (2% to 5%) of pile diameter.

Jan 1, 2017

By Babak Mamaqani, Pirooz Barar

Regional Connector Transit Corridor (RCC) is part of the Los Angeles metro expansion project under construction which adds three new stations into the system. PB&A was responsible for the design of the support of excavation (SOE) systems for two stations, 2nd/Broadway and 2nd/Hope, in RCC. In this paper, challenges and lesson learned from SOE design of 2nd/Broadway station with a main focus on underpinning design are discussed. 2nd/Broadway station required to cut and cover excavation of 500 ft long by almost 100 ft deep, underneath 2nd Street. SOE systems consisting of drilled soldier beams with tiebacks and/or struts. The main challenge in 2nd/Broadway station was to underpin the LA Times building which was partially protruded into the station. A chellenging underpinning system consisted of concrete panels and ground anchors was designed to support the building surcharge and prevent settlement. The underpinning system was designed based on METRO design criteria and the deflection was evaluated by Finite Element Analysis (FEA) program, PLAXIS 2D. A maximum deflection of 0.4 inches was calculated to occur at the top of the underpinning system. Data from settlement and tilt sensors showed minimal movements which aligned with PLAXIS outputs. PROJECT DESCRIPTION The Regional Connector Transit Corridor (RCC) is Los Angeles Metro’s ambitious Light Rail Project. It runs under the City’s main thoroughfares, Flower and 2nd Streets, and when complete will alleviate traffic and parking congestion in downtown Los Angeles. The Regional Connector will connect thousands of residents living in the bedroom communities of the Inland Empire and Long Beach to their jobs Downtown. The rail line will serve 1.9 miles, using the $1.756 Billion budget to construct the underground rail line, including 3 new stations, at 2nd & Hope Street, 2nd & Broadway, and 1st St. & Central Ave (Fig. 1).

Jan 1, 2019

By William Billiet

"The Dulles Silver Line Phase II is an 11.4 mile extension of the Washington Area Metro Transit Authority’s Silver line in northern Virginia. There are three miles of elevated guideway, which are supported on 188 large diameter mono-shafts founded within the Triassic Geologic Aged Culpeper Fault Basin. Three lateral load tests were performed on fully instrumented test shafts. The challenge in developing the load testing program was how to reproduce the effects of the extremely high design loads along the test shafts, considering the limitations of the load test equipment. Development, execution, and analysis of the lateral load test program is discussed.INTRODUCTIONPlans for Dulles Silver Line Phase II include two Aerial Guideway sections on elevated track, the Main Line and Yard Leads. The Aerial Guideways are supported on mono-shafts (single, largediameter drilled shafts) socketed into rock. Lateral loads are resisted primarily through the stiffness of the shaft and the geotechnical resistance of the rock socket. The monoshafts were designed in accordance with AASHTO LRFD 2014. Based on our preliminary analyses, the production mono shafts were expected to consist of 6.5, 7.5, and 8.5 foot diameter drilled shafts with rock socket lengths varying between 8 and 34 feet (averaging 14 feet). Table 1 summarizes the maximum service load combinations for each size production shaft along the aerial guideway alignment.GEOLOGYThe project is located within the Piedmont Province, a major physiographic province on the east coast of the USA extending from Alabama to Pennsylvania. Within the Piedmont, a number of Mesozoic basins formed in rift valleys. Dulles Airport is located in the Culpeper Basin, characterized by a relatively shallow siltstone rock surface compared to the adjacent areas underlain by Piedmont crystalline rocks. The geologic stratigraphy at the load test sites generally consist of residual soils and intermediate geo-material (IGM) overlying siltstone rock. IGM is a term used by Virginia Department of Transportation (VDOT) to describe residual material as it transitions between soil and rock. For the purposes of the load test, the siltstone rock is classified as fractured rock (RQD<50), and competent rock (RQD=50). Table 2 summarizes the stratigraphy encountered at each test site."

Jan 1, 2017

By Stephen Buttling, Zhong Rui

"A single unit gas fired power station was being built on the edge of the Gulf of Thailand in 2001. The soil conditions consisted of very soft to soft Holocene Marine Clay, and the site was part of a coast line which had been subsiding below high water mark for some time. In order to provide access around the power station a road system in a figure-of-eight formation was required, and this also needed to be above the design flood level, allowing for future settlement. A ground improvement scheme was proposed and constructed, which consisted of two spacings of prefabricated vertical drains (PVD) over two depth ranges, vacuum consolidation and pre-loading, and rigid inclusions.During the construction phase, the vacuum consolidation was applied for 202 to 221 days in different zones, and monitoring allowed a prediction that the future settlement, including secondary consolidation over a period of 25 years, would be within the range of 175 to 355 mm, which met the contract requirement of less than 400 mm.The power plant was completed and became operational in 2003. Monitoring of the road levels continued, as did the settlement, and in early 2010 the total settlement since the end of vacuum consolidation had reached about 800 mm. The monitoring data both during the ground treatment and for the following 7 years is presented and analysed. This is supported by numerical analysis using 3D finite element methods which shows good agreement with the measured data, and allows a preliminary explanation as to why the predictions were so far out.BACKGROUNDAfter a period of bidding and negotiation, the Eastern Power and Electric Co Ltd (EPEC), an Independent Power Producer, entered into an agreement with the Electricity Generating Authority of Thailand (EGAT) in November 1997 to sell them power. In 1999 an Engineering, Procurement and Construction (EPC) contract and an Operation and Maintenance contract were signed with a supplier to provide a gas-fired (with oil as a back-up fuel) 350 MW combined cycle power plant in Bang Bo, Samut Prakarn Province, east of Bangkok. The site of the plant at Bang Bo is located immediately to the east of the Samut Prakarn Wastewater Treatment Plant, adjacent to the Gulf of Thailand (see Figure 1) in an area of very soft to soft marine clay (Bangkok clay) having low shear strength and potential for excessive settlement. The site layout comprises the main Power Plant components of generating block, cooling towers, fuel unloading area and storage tanks, switchyard and administration block, separated by access roads."

Jan 1, 1900

By Mu Chen, Ye-Shuang Xu, Dong-Wei Hou, Shui-Long Shen, Huai-Na Wu

"This paper presents a laboratory investigation on the mechanical behaviors of the cement-clay admixture improved by polypropylene fiber. Cement can significantly improve the clay admixture. The fiber additive also improves the strength and ductility of the improved clay. The Unconfined Compression Strength (UCS) of the polypropylene fiber-reinforced cement-clay presents an overall trend to grow with the increase of fiber length. The improved clay reached its peak strength at the fiber content of 0.5%. Then the UCS of the improved clay will slowly reverse if the fiber content continues to rise. For study of curing time, improved clay behaves better in its early strength, but an inhibition will be brought about if fibers are excessive.INTRODUCTIONGround improvement technology is essential for construction of structures in soft ground. Some traditional techniques often cost much but result in little. For instance, along the coastal region of China, soft ground is often improved by backfill with high quality sandy soil transported far away, leading to high additional haulage costs and long construction period. Reutilizing the excavated soil as backfill or subgrade after treatment, by contrast, will be more economical and effective (Hufenus et al., 2006). Many researches have been conducted to improve the compression strength of soft soil, among which, the method of mixing the soft soil with cement and fly ash is one of the most common ways (Kolias et al., 2005; Horpibulsuk et al., 2009; Porcino et al., 2012). It is known that soil resists well against compression and shear force but behaves poorly in resistance to tension. Therefore, utilizing tensile elements such as fibers and strips to improve the tensile strength will be effective because of its strength isotropy, better durability and cost effective (Haeri et al., 2000; Kaniraj and Havanagi, 2001; Consoli et al., 2010)."

Jan 1, 2015

By David P. Sauls

Design-build contract delivery provides unique opportunities for efficiencies in pile foundation design and installation. The Louisiana Department of Transportation and Development (LADOTD) US Highway 90 at Louisiana State Highway 85 (US90/LA85) intersection was contracted under the design-build delivery system, in part to take advantage of these efficiencies. As one of five projects recognized by the Design Build Institute of America (DBIA) when it honored LADOTD as its 2011 Transportation Owner of the Year in the highway/bridges category, the design-build method provided a way for this project to be ?shovel-ready?, which enabled the LADOTD to secure American Recovery and Reinvestment Act (ARRA) funding. This paper describes the benefits this project gleaned from the design-build process, which included synergy, schedule, design and construction efficiencies, and team building. Interlaced with design and construction of precast prestressed concrete (PPC) piling in compressible southern Louisiana soils, the design-build process rapidly translated computations to cost and schedule savings. A robust quality assurance program using Pile Driving Analyzer (PDA) equipment to evaluate pile set-up provided expedited acceptance of bridge bents and advanced construction schedule. Data evaluation includes analyses of PDA data obtained from 1-hour, 24-hour, 7-day, 14-day and 6-month restrikes of the project test pile.

By Michael Hughes, Selva Selvamohan, Ray Costa

"Cutoff walls are commonly used to mitigate underseepage problems for levee remediation projects. At abrupt changes in seepage cutoff wall depths there is a potential for water to flow around the back of the deeper cutoff wall leading to elevated seepage pressures on the landside that could result in exit gradients exceeding design criteria. This condition is referred to as end-around-effects and is a complex problem that requires detailed and time consuming 3-D numerical modeling to represent accurately. This paper presents a simple approach for assessing end-around-effects using the results of 2- D seepage analysis to determine if lateral extension of the deeper portion of the cutoff wall is required. This simplified approach provides a pragmatic solution to a complex 3-D problem. The presented procedure was used as part of the Feather River West Levee Project in Yuba City, California, to assess end-around-effects at 26 locations. The results showed that wall extensions of up to 100 feet were needed at only 2 locations.INTRODUCTIONAs the lead geotechnical consultant for the Feather River West Levee Project, AECOM were responsible for designing levee remediation works for approximately 35 miles of levee protecting the area around Yuba City, California, and communities to the north and south. Due to land use constraints, seepage cutoff walls were the main remediation alternative selected to address underseepage issues for the project.As part of the design review process, the California Department of Water Resources (DWR) requested AECOM to look at 26 locations along the levee alignment where the depth of cutoff wall changed abruptly from shallow to deep, or vice versa. At these locations there was the potential for seepage pressures to pass behind the deeper section of cutoff wall and stress the blanket layer landward of the cutoff wall. A condition referred to as end-around-effects.End-around-effects involve complex 3-D ground conditions that have traditionally been addressed by laterally extending the deeper section of cutoff wall an arbitrary distance based solely on engineering judgment. In discussions with DWR, AECOM developed a simple procedure to provide a more objective assessment of end-around-effects without the need for detailed and time consuming analysis. This procedure allows the engineer to make an informed decision of whether end-around-effects are a problem at the location of a cutoff wall transition rather than laterally extending the deeper section of cutoff wall an arbitrary distance based on engineering judgment alone."

Jan 1, 2015

By Cem Altuntas

This paper is the second in a series of two describing the design and construction of a foundation for a major high-rise real estate development on the west side of Manhattan, N.Y. The foundation members consist of large-diameter rock-socketed caissons, driven closed-end steel pipe piles bearing on rock, and a secant-pile retaining wall surrounding the entire site. This paper focuses on the Osterberg cell (O-Cell) load test completed for determining the allowable side-shear resistance between the concrete and the sides of the rock socket. Different qualities of mica schist bedrock, demonstrated by the penetration of rock with the soil auger or drill casing, were encountered. Accordingly, an additional subsurface investigation consisting of test borings at each caisson location was completed. Unconfined compressive strength tests were performed on representative rock samples. The ?soft? mica schist was observed to have vertical foliations and high mica content. For the first time in Manhattan, an O-Cell load test was performed to determine the allowable side shear resistance for both the soft and hard mica schist bedrock. The side shear resistance obtained from the O-Cell load test is compared with the side shear resistance allowed by the New York City Building Code and empirical correlations using unconfined compressive strength values for rock. The rock socket design for the caissons was refined based on the O-Cell load test results.

Jan 1, 2008