Search Documents

By L. P. Srivastava

Rock bolts have been used since long to enhance the shear strength response of jointed rocks in civil and mining engineering structures. However, the assessment of strength response of a rock mass reinforced with rock bolts remains an unresolved problem till date. In the present article, an attempt has been made to study, through physical model tests, the shear strength enhancement of a blocky mass due to provision of passive rock bolts. Direct shear tests were conducted on large specimens of size 750 mm x 750 mm x 900 mm of rock mass under a normal stress varying from 0 to 2.0 MPa. Concrete was used as a model material to simulate intact rock and, elemental blocks of size 150 mm x 150 mm x 150 mm were used to form the mass specimens. Steel bolts of 6 mm diameter with 2 mm thick grout were used to reinforce the mass. Three different configurations of bolts were adopted. Observations were made on shear stress, horizontal shear displacement, and dilation during the tests. Effect of normal stress and reinforcement on peak shear stress and shear stiffness was studied. It is observed that the rock bolts enhance the shear strength of the mass by preventing sliding along the shearing plane, and by inducing additional normal stress due to tension mobilized in the bolts. The rock mass, therefore, becomes stronger due to the high degree of interlocking produced by the bolts. Shear strength of the mass increases with increasing numbers of bolts. In the case of reinforced mass, the enhancement in shear strength due to provision of bolts decreases with an increase in normal stress. The provision of bolts improves the cohesion of joints substantially. The effect on friction angle is low. The shear strength enhancement depends on the area of the bolts, spacing of the joints, spacing between the bolts and the cohesion of the intact material. A correlation has been established using which the enhancement in shear strength due to the provision of bolts can be assessed.

Jan 1, 2015

By W. Fergusson

This paper takes a look at the use of rubber to provide corrosion resistance and wear resistance in the mining industry. The longer life and reduced down time involved with the use of rubber are stressed, and examples are given of applications in grinding mills, skips, discharge chutes and screens.

Jan 1, 1979

By C. D. Anderson, C. G. Anderson, P. R. Taylor

"Rare Earths have become critical for our energy and materials driven society. While primary production must ramp up to fill growing demands, the recycle of these strategic elements must also be initiated. This paper will outline the potentials of and metallurgical technologies employed for Rare Earths recycle from various secondary sources.INTRODUCTIONWhen investigating the recovery of rare earths from secondary sources it is necessary to understand the nature of the sources to be processed. As of 2009, the USGS reports the distribution of rare earths by end use, in decreasing order, was: chemical catalysts 22%, metallurgical applications and alloys 21%, petroleum refining catalysts 14%, automotive catalytic converters 13%, glass polishing and ceramics 9%, rare earth phosphors for computer monitors, lighting, televisions 8%, permanent magnets 7%, electronics 3%, and others 3% (USGS, 2011). Additionally, it is reported that the amount of recycling was quite small and consisted primarily of rare earth magnet scrap, although with the sharp increase in the price of rare earths, and the potential shortage in supply, focus in this area is continually growing. Thus, the opportunities, whether realistic or not, are extremely vast in the recycling of rare earth containing materials. The following subsections will present methods proposed for the recycling of rare earths based on the feed material type.RECYCLING OF RARE EARTH MAGNETSCurrently, investigations are ongoing in the area of recycling production scrap and end-of-life materials in the rare earth magnet industry. The following techniques illustrate potential methods for the recovery of rare earths from secondary RE magnet sources.Recycling of Rare Earth Magnet Sludge by Selective ChlorinationDuring the production of neodymium magnets, a by-product of production is the so called “magnetic sludge”. This by-product contains high amounts of neodymium, thus a process for the recovery of Nd has been proposed. In this process the Nd present is selectively chlorinated/distilled by the addition FeCl2 via the following reactions."

Jan 1, 2012

By A. Scheltema Beduin, H. Oterdoom, A. Haaks, C. Kempe, A. Liedtke

The bath level measurement is applied in many furnaces to keep control of the level of slag and metal or matte inside. The BLM is used mainly in bath processes, and has not seen much evolution in its basic functionality. For a closed DC FeCr furnace, special demands based on the furnace design and extreme process conditions were considered for the design of a bath level measurement in order to collect valuable information about the furnace operation. This paper will describe these demands and the solutions for them, followed by some of the uses for the BLM in a closed FeCr furnace. Some of the future developments on the BLM conclude this presentation.

Jan 1, 2015

By Makhlouf Boubahziz

The HNIA field is part of the Tinrhert project which consists of developing 17 fields containing essentially gas with a few small rings of oil. It is considered as one of the main fields in this project in terms of its area and the number of geological structures that has formed it. It is a wide anticline of Cambro-Ordovician age, orientated NNE-SSW and located in the South-eastern part of Illizi basin. This structure extends from Alrar-center in the North, to the North of In Amenas in the South. The area is 1350 km2. The main reservoirs forming HNIA field are the Devonian (F2, F3 and F4), Siluro-Devonian (F6) and Cambro-Ordovician. These latest are formed by 4 sandy units alternated by layers of shale and shaly silt termed from the base to the top as follow: Unit II, Unit III-3U, Unit IV-2L and Unit IV3; these units are the subject of this study. The HNIA field is essentially gas, up to day this field is at the stage of appraisal and evaluation in order to establish a development plan; therefore the main target of this study is to contribute to this frame work. The following objectives are: ?To build a structural model of the study area. ?To integrate all the sedimentological, structural and petrophysical data in order to build a 3D geological model

Aug 1, 2013

By Mohan R. Srivastava

- OUTLINE - apologies and explanations - a quick bit of history - the wisdom of Wikipedia - ?Matheronian geostatistics continued to convert Bre-X?s bogus grades and Busang?s barren rock into a massive phantom gold resource?? - variogram analysis for Busang - would variogram analysis (or variance analysis) have revealed the fraud? - what went right, what went wrong

May 1, 2007

By Kenneth Blower

This paper gives a detailed coverage of the ore flow through the primary crusher, cobbing plant and concentrator, including equipment sizes, recoveries, reagent consumptions and product descriptions. Special features, such as rubber chutes, rubber-lined mills, pebble-mill grinding, steam-hooded filters and process control instrumentation, are also discussed.

Jan 1, 1968

By P. Mišcevic, B. Kavur, I. Vrkljan, N. Štambuk Cvitanovic

It is known from earlier and recent research that mechanical properties of intact rock like uniaxial compressive strength (UCS), Young's modulus (E) and Poisson's ratio (?) are influenced by shape deviations of test specimens as deviations from the ideal cylinder. That impact can be significant at certain level of inaccuracy of specimen preparing, and it should be objectively evaluated and controlled in testing. The effects of intact specimens side straightness, ends flatness, ends parallelism and perpendicularity to the specimen axis, on UCS, E, and ?, measured in several actual ways during laboratory compression tests, were determined by previous research on 90 homogeneous specimens of limestone. In this paper, we subject these new experimental results to Response Surface Methodology (RSM) to model the mentioned dependence, to identify significant connections of variables and to evaluate the conclusions obtained directly from experimental phase. This study indicates how the responses of the model (outputs) – parameters UCS/E/??of limestone rock depend on factors (inputs) – parameters of specimen shape deviations like flatness R, parallelism P and perpendicularity O, assuming modern test machines with spherically seated upper platen. Starting from general RSM model with three factors (R, P, and O), we investigated the multiple linear regression models of specific mechanical property (UCS, E, and ?). Using the NCSS program ("NCSS 2004 and PASS 2005") in several steps, final models with very high coefficients of determination were developed for properties with the most evident effects of specimen shape deviations: nine models for strength UCS and UCS50 (equivalent UCS for specimen with 50 mm diameter), and three models for ?L (Poisson's ratio calculated from axial deformations measured on the entire specimen length). These statistical models with their response surfaces further strengthen and confirm the results and conclusions from the experimental phase. The critical values of R, P, and O are established using an additional statistical analysis to determine the lower and upper engineering limits. These findings set the basis for the new eligibility criteria for specimens of limestone (and similar rock with UCS about 100-150 MPa) in further testing of strength and deformability.

Jan 1, 2015

By A. Brown

"The mining industry is no exception to the general rule that continuing research is essential to good management; in fact, because of the imperfect state of knowledge in regard to many important factors associated with a mineral extraction, mining research assumes a position of unusual importance. On the basis of a recent visit to mining research centres in a number of European countries, the author describes their organization and their role in the mining industries of these countries. Some observations are made on Canadian mining research efforts, with a view to indicating a more systematic basis of procedure."

Jan 1, 1960

By A. Jordens, Y. Zhiyong

"IMBSRE, one of the largest rare earth element (REE) producers in China, produces a rare earth oxide (REO) concentrate as a by-product by floating the middlings stream from a low intensity magnetic separation step in the main iron ore processing stage. As the mine depth has increased, flowsheet changes in the main iron ore circuit have reduced the REO grade and increased the magnetite to REO ratio in the middling product used as flotation feed for the REO circuit. Extensive laboratory work was carried out and identified a new modified hydroxamic acid product, Florrea 8920, that could provide better metallurgical results over the standard hydroxamic acid used as the main collector. This paper briefly reviews the use of hydroxamates in the flotation of oxide minerals, provides detailed information on the different hydroxamates available from Florrea and then provides a case study of the successful implementation of the Florrea 8920 product in a commercial Chinese REE flotation plant. The case study consists of a one year program of pilot plant testing and industrial trials to confirm the results of laboratory tests. The implementation of the new collector resulted in an improvement in grade and recovery to 61% and 64% respectively. The new collector also provided significant economic and environmental benefits.INTRODUCTIONThe flotation of rare earth element (REE) bearing minerals is a topic which has been dominated in the English language literature by the work conducted on the Mountain Pass bastnäsite deposit (Pradip, 1981; Fuerstenau, Pradip, Khan, & Raghavan, 1982; Pradip & Fuerstenau, 1983, 1985, 2013; Fuerstenau & Pradip, 1991; Fuerstenau, Pradip, & Herrera-Urbina, 1992; Herrera-Urbina, Pradip, & Fuerstenau, 2013). By far the most important collector type used for the flotation of rare earth minerals (REM) is hydroxamates. These reagents were initially extensively described as REM collectors in the English literature by Pradip (1981) however they have been successfully applied to numerous other minerals such as: cassiterite (Sreenivas & Padmanabhan, 2002); pyrochlore (Gibson, Kelebek, Aghamirian, & Yu, 2015); hematite, chrysocolla, rhodonite, hubnerite and pyrolusite (Fuerstenau, 2005); and malachite (Lenormand, Salman, & Yoon, 1979) amongst others."

Jan 1, 2016

By F. K. McKean

THE task of establishing a new corrosion testing laboratory is more difficult than it need be because there is very little information on the subject available in the literature. Many articles describing tests and results may be found, but a wide search will unearth only passing remarks on the different types of equipment that may be selected for accelerated corrosion tests. An article describing some of the apparatus needed in a corrosion laboratory should be of help to those interested in building a new unit or in making additions to an old one. In May of this year, the writer was given the assignment of equipping a laboratory for general corrosion testing, to form a part of the new Physical Metallurgy Research Laboratories of the Department of Mines and Resource~ at Ottawa. With the help of senior members of the staff, along with what could be gathered from other sources, a list of necessary equipment was compiled and a plan for arranging it in the rooms was decided upon. Where possible, the apparatus was constructed in the excellent machine shops at the disposal of this Department, while the rest was placed on order with the manufacturers.

Jan 1, 1945

By A. Navarra, C. Arrancibia, R. Yañez, C. Acuña, F. Valenzuela

"Discrete event simulation (DES) is a suitable framework to evaluate and optimize the dynamics of sulphide smelters. In particular, iron-nickel-copper-cobalt sulphides undergo continual oxidation within a roasting or smelting operation, followed by batch oxidation within the converting operation, thus producing iron-free Bessemer matte (or blister copper, in the case of copper smelters); this semi-finished product undergoes further processing to produce nickel, copper and cobalt products, and to recover precious metals. The juncture between continuous smelting and batch converting is often an appropriate focus for the earliest phases of DES development, since it is typically a major bottleneck within nickel and copper smelters; later phases may include increasing levels of detail for auxiliary unit operations, as well as plant logistics. Moreover, DES can support matte-slag chemistry, including Gibbs free energy balances to determine the iron speciation within the slag. DES is therefore capable of linking the fundamentals of oxidation reactions to the intricacies of plant dynamics.INTRODUCTION Discrete event simulation (DES) is gaining acceptance within the extractive metallurgy community, as a technique that quantifies the system-wide performance of metallurgical plants under conditions of uncertainty (Wheeler & McGinty, 2015). In particular, over 90% of smelters that process nickel-copper-cobalt sulphides and copper sulphides exhibit similar semi-continuous dynamics (Crundwell et al., 2011b; Schlesinger et al., 2011b), in which the converting aisle produces batches of material that are sent for further processing (Figure 1). Thus the tools and practices that are developed for a specific sulphide smelter are often relevant to numerous other smelters.The juncture between continuous smelting and batch converting has long been a focus for discrete event simulation (Welgama et al., 1996). Nonetheless, the broad acceptance of DES in nonferrous smelters has been hindered by interdisciplinary barriers that divide industrial and metallurgical engineers (Navarra et al., 2016; Noorossana et al., 2012); this divide has been less severe in steel plants (Hollocks, 2006). In recent years, DES has been used in copper smelters to analyze crane-and-ladle motions (Coursol et al., 2009a), reverts production and consumption (Noorossana et al., 2012), and innovative control systems (Herrera et al., 2016); additionally, DES models have accounted for shutdowns and random breakdowns to provide realistic assessments of copper smelter capacities, thus guiding equipment upgrades (Campbell et al., 2013; Coursol et al., 2009a). All of these studies feature a Peirce-Smith converting aisle similar to Figure 1 that, under normal operations, constrain the smelter throughput, and are thus a bottleneck (Campbell et al., 2013; Navarra et al., 2016)."

Jan 1, 2017

By A. Sutherland Brown, Stuart S. Holfand

"The Northeastern part of the Cariboo district lies in the big bend of the Fraser River between Quesnel and McBride. The area shown on Figure 1 extends from just west of Wells to Isaac Lake, about 30 miles across the regional strike of beds.Topographically the area extends from the moderately well dissected Interior Plateau in the west through a transition zone to the fully dissected Cariboo Mountains in the east.The area is an important source of lode and placer gold. The Cariboo Gold Quartz and Island Mountain lode-gold mines have produced more than 32 million dollars in bullion since 1932. Placer-mining has probably produced an equivalent or greater amount, although only 15 million dollars is officially recorded because accurate statistics. were not kept until fourteen years after the origiiaal gold rush of 1860.The regional structure of the Barkerville district was summarized by Lang in the Jubilee Volume (1948, pp. 141-149). Since then a large amount of detailed and areal mapping by the writers has expanded the information available and made necessary a complete revision of the regional geology. Much of the information summarized in this paper, together with a full discussion of the revisions, may be found in British Columbia Department of Mines Bulletins, Nos. 34 and 38, but other information is as yet un-published.Rocks of the Kaza group are exposed in the core of the Lanezi anti-clinorium between Spectacle and Isaac Lakes. The main part of the group is composed of greenish micaceous greywacke and greenish schist with knots of garnet, biotite, or both, and minor amounts of pebble conglomerate. The upper 1,000 feet is composed of white to brown quartzites and brown phyllites. Altogether, about 6,000 feet of the group is exposed. 1t is of latest Precambrian, i. e. Windermere, age."

Jan 1, 1949

By Yu. V. Ponomarenko, A. I. Meka, P. A. Witherspoon, Yu. I. Volkov, J. E. Gale

"The mining of iron ore in the Kursk Magnetic Anomaly (KMA) region of the U.S.S.R. is done mostly by the open-cut method. An assembly of open pits capable of producing about 100 million tons of ore per year makes KMA the largest iron ore field in the world. Three gigantic open pits are currently in operation: Lebedinsky, Mikhailovsky and Stoilensky. These pits are as large as 13 km2 on the surface and as deep as 230 m. The mining operations are constantly faced with the problem of flooding from aquifers that overlie the orebodies; the magnitude of the problem is evident from the fact that the present groundwater inflow to these three pits is about 110 million mt /yr.Under such conditions, safe operations and pit wall stability are of great importance, and this has been accomplished very effectively by the appropriate use of seepage barriers and drainage systems. At KMA, the most important items used in the system of groundwater control are standard pumping wells, raise wells that drain into a 20 km to 30 km long underground drift located just outside the perimeter of the pit, horizontal wells driven through the pit walls, and horizontal drains. This paper describes the mining and engineering technology that have been developed at KMA to control the groundwater systems and protect the mines from flooding."

Jan 1, 1992

By J. Cueto, M. Torres, J. Fernandez, J. Nuñez, C. Salgado, G. Zarate

Anglo American has used the extractant M 5640 in all the Divisions, which is an aldoxime modified with TXIB formulation, except in Los Bronces, where an aldoxime modified with tridecanol (TDA) formulation is used. It is a well-known fact that the aldoxime degrades while the modifier does not. With time the aldoxime/modifier ratio decreases significantly depending on the operating conditions of each plant. In order to evaluate the effect of this increasing modifier content in the organic of the plant, especially in the organic losses, a complete metallurgical test work program was started at laboratory and pilot plant scale. Results showed that the addition of aldoxime without modifier does not affect the chemical performance of the organic phase, but there is a significant decrease in the viscosity and density of the organic phase. Based on the results obtained in the metallurgical program, it was decided to run plant scale tests at both SX plants, Mantos Blancos and Mantoverde. In these tests, instead of adding the usual formulation of aldoxime modified with TXIB to maintain the organic inventory, CuPRO MEX™ 3406 which is an aldoxime without modifier is going to be added until the original aldoxime/modifier ratio is reached. The plant tests started in April 2013 at Mantos Blancos and in June 2013 at Mantoverde and will last 18 months. The results obtained at the laboratory and pilot plant scale, together with the preliminary plant test results, are discussed in this paper.

Jan 1, 2014

By J. A. Vezina

The effects of particle size distribution on metal extraction have been determined from pressure leaching Renzy Mines Limited concentrate with oxygen. Using a pulp density of 30 per cent solids, an oxygen pressure of 80 psig, a temperature of 230°F, a grind of 2.5 hours and a retention of 8 hours resulted in the almost complete dissolution of the nickel and the cobalt and the decomposition of over 96 per cent of the chalcopyrite finer than 20 microns. Only 11 per cent of the chalcopyrite coarser than 20 microns was reduced to smaller than 20 microns.

Jan 1, 1973

By John C. Lyons

"The Wabana iron ore deposits occur as flat-dipping beds of oolitic hematite and chamosite, of Lower Ordovician age, which outcrop for 3 miles along the northwest coast of Bell Island, Conception Bay, Newfound-land, about 16 miles from St. John's.The deposits occur in three zones, Upper, Middle, and Lower beds, separated respectively by 30 feet and 215 feet of shale and sandstone. They are primary sediments laid down in a shallow tidal basin by the precipitating action of a marine environment on iron-rich fresh waters flowing into the basin.The ore-bearing zones, while of wide areal extent, are not uniform beds of hematite that can be mined wholesale. The action of waves and currents during sedimentation; the delta pattern, velocity, and transporting power of streams flowing into the basin; the contours and oscillations of the sea bottom on which the sediments were laid have all been fundamental in the emplacement of richer and thicker mineable sections, and of lean zones so intercalated with shale as to be unmineable.The preservation of the deposits is due to their location in the Conception Bay syncline and to a considerable upthrust of the country east of the bay in post-Ordovician time.The hematite deposits were first recognized as such in 1892, and soon after were acquired by the Nova Scotia Steel and Coal Co. They are now being mined by Dominion Wabana Iron Ore, Limfred, a wholly owned subsidiary of the Dominion Steel and Coal Corporation, Limited. Production started in 1895, and up to the end of 1955 totaled 58,588,516 long tons of hematite ore, having an average dry analysis of about 51 5 per cent iron, 11 8 per cent silica, 0·9 per cent phosphorus, and l ·5 per cent moisture. About 40 per cent of the total tonnage mined has come from surface stripping and on-shore mines. These areas have now been almost completely depleted, and operations are confined to submarine mines extending for two miles off shore under the waters of Conception Bay. Three sub-marine slopes are currently in operation, Nos. 3 and 4 working in the Lower Bed and No. 6 in the Middle Bed. A general picture of the workings is shown in isometric projection in Figure 1. Submarine mining has been entirely by the room-and-pillar method, with an extraction of 60 per cent. The deepest workings, at a vertical depth of 1,850 feet below sea-level, have a rock cover of about 1,500 feet. No mining is done in areas where the rock cover is less than 200 feet. To date mining has explored six square miles of a potential area that may exceed 50 square miles."

Jan 1, 1949

By H. J. White

The effect of alloying elements on the mechanical properties and weldability of wrought gamma prime strengthened nickel- base superalloys is well known. An understanding of the basic guidelines concerning alloying additions has led to the invention and development of HAYNES® 282® alloy for applications in aircraft and land base gas turbines and other high-performance high-temperature environments. The alloy combines exceptional high temperature properties with good weldability and fabricability. At high temperatures (~ 900 °C), the alloy is stronger in creep strength than Waspaloy alloy (UNS N07001) and it approaches the creep strength of R-41 alloy (UNS N07041). Because the alloy has better thermal stability, fabricability, and weldability than Waspaloy and R-41 alloys, it is currently being considered as a candidate universal consumable for welding/ repair welding of gamma prime strengthened nickel based superalloys and it is also being considered as a suitable replacement for applications where R- 41, Waspaloy, and 263 (UNS N07263) alloys are currently being used. The alloy was designed to have improved resistance to strain age cracking, a problem common to gamma prime strengthened nickel based superalloys. In this paper, we present (1) results from hot ductility testing of annealed and annealed/aged material; (2) results from Time Resolved X-ray Diffraction (TRXRD) studies during a welding thermal cycle of annealed and annealed/aged material, and (3) gas metal arc (GMA) and gas tungsten arc (GTA) welding of annealed and annealed/aged material.

Jan 1, 2010

By A. S. Romaniuk

More than a decade ago, CANMET management recognized the need to make better use of existing technological information in mining and extractive metallurgy-two fields basic to the economic well-being of Canada. There were at that time no indexes or files dedicated to disseminating technical information for the many minerals mined and processed in Canada, including coal. CANMET, with the nation's largest research and library resources in the minerals field, was in a unique position to fill this need. Initial efforts were concentrated on building a mining file, beginning with identification of world sources of published information, development of a special thesaurus of terms for language control and adoption of a manual indexing/retrieval system. By early 1973, this file held 8,300 references, with source, abstract and keywords given for each reference. In mid-1973, operations were computerized. Software for indexing and retrieval by batch mode was written by CANMET staff to utilize the hardware facilities of EMR's Computer Science Centre. The resulting MINTEC file-one of the few files of technological information produced in Canada-is the basis for the national literature search service in mining offered by CANMET. Attention is now focussed on building a sister-file in extractive metallurgy using the system already developed. Published information sources have been identified and a thesaurus of terms is being compiled and tested. The software developed for CANMET's file-building operations has several features, including the selective dissemination of information and production from magnetic tape of photo ready copy for publication, as in a bi-monthly abstracts journal.

Jan 1, 1979

By L. Zhu, S. Kaierle, M. Dahmen, C. Zimmermann, T. Haubold, I. Kelbassa, C. Mattern

Application of integrally bladed disks (blisks) is of increasing interest in compressors of aero engines. Blisks are preferred due to their potential for size and weight reduction, for increased performance and for reduced manufacturing costs compared to conventionally bladed disks. In case of a damage the blisk aerofoils cannot be simply replaced. If the damage is beyond acceptance or blending limits refurbishment is possible only by scrapping the whole blisk assembly, or more cost effective by the application of advanced weld repair methods. Weld repair of blisk aerofoils is challenging as it affects a critical part with specific requirements regarding its mechanical integrity, and as the accessibility is usually limited. The paper describes the ongoing development of advanced weld repair processes as part of a comprehensive repair strategy which have been developed for small-sized blisk assembly to give competitive maintenance cost.

Jan 1, 2006