Search Documents

By J. W. M. Porritt, K. C. Cheng

Knowledge of radon emanation rates from uranium-bearing rocks is essential to the design of mine ventilation systems for uranium mines. Measurements of equilibrium ratio between radon and its daughters in mine air are important for a better control of mine radiation conditions. The concentrations of radon and daughters were monitored at cut-and-fill stopes in the Beaverlodge Mine of Eldorado Nuclear Ltd. during all phases of the mining cycle. The radon emanation rates of ore and rock samples were measured at the laboratory and the results were compared with in-situ emanation tests in an isolated ore drift. Samples of backfill solution, backfill drainage and ground seepage water were measured [or radon and analyzed for radium and uranium. The results showed that discharges of backfill solution and daily shift-end blasts were the two major sources for a rapid release of radon gas in the ventilation air. Other mining operations, such as drilling, mucking, etc., contributed little effect on radon release to the mining environment. Radon emanation rates of the Beaverlodge are samples ranged from 13 x 10-18 to 600 X 10-18 Ci/cm2/ sec and that of waste rock samples from 0.54 x 10-18 to 13.4 X 10-18 Ci/cm2/sec. The in-situ emanation rate of mine walls with ore-to-rock ratios of 1 to 7 was 60 x 10-18 Ci/cm2/sec. The average equilibrium ratio of radon and its daughters in stapes was 32.6%. Under a normal ventilation condition, the average background levels of radon concentration in cut-and-fill stopes ranged from 13 to 80 pCi/L. The discharges of backfill solution during backfill operations at 100 tons solids per hour released approximately 1.8 x 106 pCi/min of radon and elevated radon concentration in stapes 2 to 5 times above the background levels.

Jan 1, 1981

By Walter Valery, Lauren Hafla, Megan Tibbals, Adrian Dance, Jeff Snyder

"Newmont Mining Corporation’s Carlin (“Carlin”) operation processes roaster feed through a double rotator, dry grinding mill following secondary crushing. Metso Process Technology & Innovation (“PTI”) was involved in a review of crushing and dry grinding circuit operations in August 2009. A number of opportunities for increased throughput were identified in the PTI study.Extended plant trials were conducted in July 2010 to provide justification for possible circuit modifications and if needed, additional equipment. The trials confirmed that a finer crusher product would reduce the build-up of material ahead of the coarse grinding chamber in the double-rotator. Also revealed were material transport and airflow restrictions in the dry grinding circuit that resulted in a high circulating load.The secondary crushing plant demonstrated it was capable of reducing the amount of +¾” material in the mill feed thus increasing dry grinding throughput. However, wet and sticky feed affected screening efficiency resulting in low utilisation of the existing crusher capacity. The open circuit configuration also made it difficult to control crushing circuit product size.For the dry grinding circuit, changes in grinding media size, transfer grate design and increased airflow were recommended to reduce circulating load issues and increase circuit capacity. This paper summarises the crushing and grinding circuit review, the extended site trials performed by PTI and the improvements in dry grinding operation that resulted from this study."

Jan 1, 2012

By W. S. (Steve) Vaughan

The Origins of Joint Ventures in Canada?s Mining Industry ? Among the most important financing structures used in our mineral industry today ? Virtually unheard of in the Canadian industry prior to the 1970s ? Borrowed from the U.S. oil and gas sector where it came into prominence in the late 1930s ? The Securities Acts of 1933 and 1934 in effect killed the sale of (equity) shares for financing oil and gas wells and start up mining companies

May 1, 2013

By R. A. Campbell, R. R. Rogers

"AbstractThe experiments described show that crude bismuth metal containing up to 5 per •cent lead, 0.14 per cent silver, 0.015 per cent copper, 0.02 per cent iron, .and small amounts of antimony, nickel, and tin may be refined to a bismuth content of 99.98 per cent by distillation followed by chlorination. It also is shown that bismuth trichloride of high ,purity may be produced by passing chlorine over hot •crude bismuth metal and allowing the resulting vapours to •condense in a cooler .part of the system.IntroductionBISMUTH is used in the production of alloys and pharmaceuticals. During 1952, the New York price for the refined metal was $2.25 per pound in ton lots.Some months-ago a Canadian producer requested the Mines Branch to investigate methods of refining the bismuth which they had been producing. Their crude product had been selling for $1.50 to $1.70 per pound and it was desired to increase its purity to at least 99.98 per cent so that it could be sold for $2.25 per pound."

Jan 1, 1955

By J. R. Foster

Investigations into the effect of a variety of acid digestions on common rock-forming minerals demonstrated a considerable variation in the proportion of the total metal extracted. A similar situation applies to the analysis of a number of common rock types. In addition, grain-size variation has an effect on the amount extracted by certain digestions. This work indicates that considerable care needs to be given to selecting an appropriate acid digestion capable of determining metal held in particular components of a sample. By using partial extraction techniques, the identification of certain patterns of metal distribution, undetectable by normal methods involving total metal analysis, may be achieved.

Jan 1, 1973

By N. W. Hendry

ABSTRACT Exploration by geophysical methods and diamond drilling of an occurrence of chrysotile asbestos, located ten miles east of Matheson, Ontario, was commenced on March 25th, 1949, by the Canadian Johns-Manville Company, Limited. The asbestos is associated with a narrow sill-like body of basic and ultrabasic rocks which strikes northwesterly across portions of Munro and Beatty townships. To date, asbestos zones of commercial interest, many hundreds of feet in length, width, and depth, have been outlined by diamond drilling along a 2-mile length of serpentine. The fractures occupied by the asbestos veins are closely associated with the regional faulting in the area. The mining of the first occurrence, or A orebody, will be by open-pit methods. Milling will commence at a rate of 50 tons an hour. INTRODUCTION OCCURRENCES of chrysotile asbestos in Munro township have been known at least since 1914 and references to them appear in reports published by the Ontario Department of Mines in 1915 (1) and 1919 (2). J. G. Ross (3) in his excellent publication on Chrysotile Asbestos in Canada, mentions an occurrence in Munro township. The area was first mapped in detail by J. Satterly, of the Ontario Department of Mines, in 1944, and brief mention is made of chrysotile asbestos in Satterly's preliminary report (4), which was published the following year.

Jan 1, 1951

By Sandeep Singh Sandhu, Karanvir Singh Ghuman, Manjit Singh

"Cobalt based super alloy stellite 6 was weld cladded on AISI 304 L stainless steel using SMAW process in order to improve the wear resistance for tyre crusher blades. Microstructure characterization and micro hardness testing was performed on stellite 6 cladding. The suitable parameters viz. 80 Amp current with arc weaving technique was selected by performing bead on plate experiment were further used for depositing multipass multilayer cladding to achieve full filler chemistry at the top surface. Further GTAW process was used for re-melting the top surface of the cladding. Comparative evaluation of the claddings showed that TIG re-melting resulted in increased microhardness and wear resistance in comparison to as cladded specimens even with lesser deposition of material. It was observed that TIG re-melting improved the hardness from 603 HV0.5 kg to 712 HV0.5 kg. Micro structures of stellite 6 contained cobalt solid solution matrix along with inter dendrite chromium carbides which resulted in the increased micro hardness values. Pin on disc abrasion tests were carried out at room temperature and the worn out surfaces were characterized using SEM and EDS.INTRODUCTIONThe crusher blades are used in many industries for crushing various types of material and its wider applications in tyre rubber crushing mills, metal-powder crushers industries etc. Most of the crusher blades are damaged by the wear and impact loading conditions. It is because of metal to metal abrasion and the temperature also plays a vital role in blunting the cutting edges of these blades. The wear is the major cause which leads to loss of material and thus the productivity that can never be recovered (Kotechi et al., 1992). The wear can be reduced by coating of various super alloys which could reduce the behavior of metal degradation even in aggressive environments. Cladding of cheaper low alloyed material with expensive superalloys to enhance the performance of components at low cost has been investigated by many scholars (Deng et al., 2010, Kennametal, 2007, Lolla et al., 2014, Singhet al., 2014, J.N et al., 2003, Ramkumar et al., 2012). Many researchers have reported that cladding is an application of build-up deposits of specialized alloys to resist abrasion, high temperature corrosion and impact loadings. Cladding is used for providing required mechanical strength properties as well as inhibition of oxidation and other corrosive degradation. Coatings are used to protect the heat affected areas like tubes of fluidized bed combustor etc. (Kirchbner et al., 2008, Wang et al., 1994, Hocking et al., 1993, Ananthapadmanabhan et al., 1991, Staia et al., 2001). Coating techniques are widely used for the protection of turbine engine and boiler tubes against high temperature corrosion attack, power generation equipment, chemical process equipment, aircraft engines, pulp and paper processing equipment, bridges, rollers and concrete reinforcements, orthopedics and dental, land-based and marine turbines, ships. Coatings of stellite 6 are widely used in steam turbine blades and boiler tubes for power generation because of an excellent combination of impact, wear and other properties. It can maintain its properties even at high temperature and in harsh environments (Kobayashiet al., 1999, Alam et al., 2009, Munehru et al., 2009). The loading and unloading conditions experienced by the material may induce the surface cracks which lead to its breakage and leaving large pits in the surface (Meng et al., 1995). Many researchers have reported that the properties of cladded layers can be increased by various techniques such as controlling the current variations, dilution, heat input, laser and other re-melting processes, addition of special alloying elements, speed of weldingetc(C.M Anaet al., 2002, Kumaret al., 1999, Luo et al., 2012, et al., Madadi et al., 2011, Shin et al., 2003, Kuzucu et al., 1997, Sudha et al., 2008, Sawant et al., 2017, Houdkova et al., 2016, Ciubo"

Jan 1, 2017

By Chris G. Dobson

Introduction The Britannia mine is at Britannia Beach, on Howe sound, approximately thirty miles from Vancouver. The first claims were staked in 1898, and a local company was formed at that time to develop them. In 1904, Mr. Grant B. Schley became actively interested in the property and in the following year the Britannia Mining and Smelting Company, Limited, was incorporated to operate it. This Company was taken over a few years later by the Howe Sound Company, Limited. The mine comprises five more or less separate ore-bodies, which have produced approximately 20,000,000 tons of ore to date. The East Bluff ore-body, with which the present paper deals, is well suited to large-scale mining by means of carefully placed powder blasts. It covers approximately an acre and lies in the slate footwall, in a bay produced by a fault. The hanging-wall side, on the west, forms the face of the Bluff glory-hole, which extends to the 1,200 level. A portion of this ore was available for breaking into this old glory-hole, below which four bulldoze chambers could quickly be built. Mining of this block is complicated by a very soft footwall, which 'runs' badly when broken. In stoping, care is taken to guard against the hazard of dilution by deliberately leaving a small portion of ore on the footwall. Some of this will undoubtedly be lost, but it is hoped to recover a fair amount of it after the major drawing is completed. The deposit occurs in a greenstone which has been highly silicified following brecciation. The chief minerals are chalcopyrite, sphalerite, and pyrite. Concentrates of copper, zinc, and pyrite are made at the mill. The average grade of ore runs 0.7 per cent copper, 1.5 per cent zinc, and 0.03 oz. gold per ton. The rock, which is practically a chert, is extremely hard, but shatters well. Both in stoping and drifting, holes must be closely spaced and powder used generously. Development When development work started in the East Bluff, there were no raises and only one drift on each level in this section of the mine. After blocking out the ore by thorough diamond drilling, a production of two thousand tons per day was set as a goal. To obtain this tonnage from so small an area required a great deal of carefully planned and well timed development work.

Jan 1, 1935

By L. Drisdelle, S. Gendron

"Survival in today's business climate requires participation of all employees in a Total Quality Management Program encompassing everything - ""safety, quality of products, quality ofet1ch and every job done, and of course production "". We all know what needs to be accomplished, but struggle with how to do it, especially in an industry which has not always experienced management/union cooperation, and mistrust is still present.This paper describes a process to improve team work and employee involvement in Inco's nickel carbonyl refinery at Copper Cliff The process involves facilitatorship training for all employees, and a system for reinforcing and accomplishing the required behavioural change. The system is described in detail and a number of examples are presented. At the refinery, the staff is starting to understand as Max DePree recently wrote ""Without Quality Behaviour, you cannot have Quality Product"". IntroductionThe Copper Cliff Nickel Refinery (CCNR) is Inco's largest and most modern nickel refinery, which celebrated its twentieth year of successful operation in April 1993.The heart of the refinery is the Inco pressure carbonyl (IPq plant which produces high purity nickel pellets and specialty powders by refining an approximate 80% nickel granule feed. The carbonyl plant is a modem chemical plant with very special and demanding requirements for safety and environmental protection due to the toxic nature of the refining gas.Since 1987, there has been an emphasis at CCNR on a comprehensive Total Quality Improvement (TQI) Program which was designed based on recognizing customers' needs for improved systems for quality management. This program is customer oriented and comprises such elements as team organizational concepts, customer audits, process assessment and internal quality auditing.A detailed review of progress was made in early 1991 and it became apparent that the ""ownership"" of the TQI program was not broad based. In fact, the program was very much a staff driven effort and fell far short of total employee involvement and relentless continuous improvement that are now considered essential to remain competitive and stay in business.Inco staff has now come to regard that early phase of our TQI program as ""the technical aspects of total quality improvement"".The safety experience was also puzzling. Even though the safety statistics were good with an average lost time frequency of 1.6 for the last five years, the perfonnance improvement had plateaued and remained pretty much the same. Clearly a new approach was required if significant progress and continuous improvement was to be made."

Jan 1, 1994

By S Romanchuk, V N. Macvkiw, D. J. I. Evans

The paper describes the processes developed and piloted by Sherritt Gordon Mines Limited for recovering copper, in the form of specification copper powders, from Lynn Lake sulphidic copper concentrates and Fort Saskatchewan Refinery by-product copper sulphides. The process includes ammonia pressure leaching and hydrogen reduction from solution. Nickel and cobalt present in the con-centrates dissolve in the leach solution and a method was developed for separating these metals from the cop-per. Methods are described for con-trolling the physical properties of the copper powder produced in the reduction vessel. The chemistry of the process is briefly discussed and the effects of some of the more important process variables are described. SHERRITT Gordon Mines Limited have developed and proven on a pilot plant scale, a process (I) for the production of copper powder

Jan 1, 1961

By K. V. Gow, F. A. Jerabek

"THE NOVA SCOTIA TECHNICAL COLLEGE has been granting degrees in mining engineering since 1909. The college was established in 1907 to provide the final two years of the undergraduate program in engineering the earlier years of which are given at several small universities scattered around the Atlantic Provinces. Since the beginning of the program, 251 Bachelor of Engineering degrees have been awarded in mining engineering. Although the average class size has been small, increases in enrolment in the past few years have resulted in Nova Scotia Technical College being the second largest mining department in Canada, based on the number of graduates per year. This year 18 students received B.Eng. degrees, and next year 17 will graduate.In 1968, it was necessary to make a decision on whether or not to abandon, for economic reasons, the program in mining engineering. For several years enrolment had been very low and resignations among the mining engineering staff created a situation in which the program could easily have been dropped. However, it was decided to continue mining engineering, as it was the only such program in the Atlantic Provinces. New staff members with many years of practical experience in the mineral industry, not only in Canada but in the U.S.A., South America, Africa and the U.K., joined our department. At the same time the enrolment in mining engineering began to increase significantly."

Jan 1, 1972

By A. Himsley

This paper presents a review of the existing ion exchange resin systems for treating unclarified pregnant liquor, with particular reference to uranium extraction. A new concept of a truly continuous ion exchange system is described and operating details are given,of a 0.6.-m (24 in.) diameter pilot plant treating unclarified acid leach liquor.

Jan 1, 1977

By Joseph D. Martinez

"The benefits of modern technology can readily be identified with energy availability. A clear correlation has been established between per-capita energy consumption and the GNP for various nations. The United States is an outstanding example of a nation which has benefited from vast energy reserves. The nation is now challenged, how¬ever, by dwindling reserves and the need to develop new sources consistent with the preservation of environmental quality. The development of new, virtually inexhaustible and environmentally acceptable sources cannot be expected for several decades. Meanwhile, we will have to depend on coal, nuclear energy and/or rigorous conservation measures.The net effect of environmental considerations has been to delay and perhaps ultimately eliminate the nuclear energy option as a national energy alternative. This forces a more positive move toward coal as the next major source of electrical power. Our coal resources are large, but the use and production of coal is also a threat to the environment. Thus, we seem to be moving from one major accessible source to another due to environmental concern only to face the probability that the alternative is also environ¬mentally unacceptable.Controversies revolving about energy choices must be resolved by an analysis of the relative benefits and impacts of these two sources and others. The pattern of changing energy sources is not new. We have moved from wood to coal to oil and gas in the past and must learn to adapt in the future. Rational decisions must be made relative to the utilization of intermediate energy sources pending development of promising future approaches. A collapse of current levels of energy supply could threaten our technological society and the means to develop a new energy base."

Jan 1, 1976

By S. N. Dixon

"Maximizing the value of each tonne of processed ore is the goal for all operations. Cyanidation processing of gold-copper ores has been challenging since its first use in 1889. The current practice treats a bleed or the total flow of mill solution to recover copper as copper sulfide (by sulfidization, acidification, recycling, and thickening), or to recover the cyanide (by acidification-volatilization neutralization). The process presented uses the adsorption of copper cyanide by carbon and the selective elution of copper from carbon to concentrate copper into a smaller stream. Copper contained in the smaller stream is precipitated as copper cyanide.RÉSUMÉ Toutes les exploitations ont pour objectif commun d’optimiser la valeur de chaque tonne de minerai traité. Depuis sa première utilisation en 1889, la méthode de traitement par cyanuration des minerais aurifère et cuprifère s’est révélée complexe. La pratique actuelle traite la saignée ou le débit total d’une solution de traitement du concentrateur pour récupérer le cuivre sous la forme de sulfure de cuivre (par sulfuration, acidification, recyclage et épaississement), ou pour récupérer le cyanure (par acidification, volatilisation et neutralisation). Le procédé présenté dans cet article utilise l’adsorption sur charbon actif de la solution de cyanure de cuivre et l’élution sélective du cuivre depuis le charbon pour concentrer le cuivre en un plus petit jet. Le cuivre contenu dans ce plus petit jet est précipité sous forme de cyanure de cuivre.INTRODUCTIONProcessing gold-copper ores by cyanidation has been a cost-control challenge since the cyanidation process was first used in 1889. Copper cyanide is stable only in the cuprous state, not the cupric. This factor results in the oxidation of a mole of cyanide per mole of nonchalcocite copper extracted. Each mole of copper extracted forms a cyanide complex with a minimum of 3 mol of cyanide. This cyanide-to-copper mole ratio is required to dissolve gold. The oxidation of cyanide and copper complexation with cyanide results in high cyanide consumption for copper-gold ores, which is a significant operating cost.One challenge in processing gold-copper ore is the cost of cyanide related to the extraction of copper. Processing 10,000 t/d of ore containing 1,000 mg/kg copper and 10% copper extraction yields 1,000 kg/d of copper. Currently, processes to remove copper from cyanide leach solution treat either the total flow of the barren or a bleed of the barren. The two processes used for copper-gold ores are sulfidization, acidification, recycling, and thickening (SART), which produces a copper sulfide product for sale; and acidification- volatilization-neutralization (AVR), which recovers the cyanide from a gas and produces a low–cyanide content solution. This low–cyanide content solution can be recycled to the process or might require additional treatment before being disposed from the operation."

Jan 1, 2017

By A. Blackmore, D. Baker, L. Human

"Mechanical mixing equipment is common in a wide variety of mining, metals and process applications, such as hydrometallurgical reactors, solvent extraction, digestors, and tanks for storage of slurry or hydrocarbons. Computational Fluid Dynamics (CFD) has been applied successfully to single-phase mechanical mixing problems for several decades and is established as a reliable design tool. As computational power and CFD codes have improved over the years, there have been significant advances in modelling capabilities including improved models of turbulence, interaction of rotating and stationary components, multiphase flows, and modelling of free surface interfaces, for example. This paper will provide an overview of the application of CFD to mechanical mixing problems. First, it will review the traditional single phase Multiple Reference Frame (MRF) approach and introduce a range of advanced modelling techniques. Three examples of the application of CFD to industrial mixing problems will be given. It will be demonstrated that CFD is an effective tool for reducing technical risk in design, for identifying the root-cause of mixing problems, and testing modifications to existing operations."

Jan 1, 2015

By G. Bridgstock, S. S. Forbes, E. M. Elkin

"OPERATIONS at Canadian Cop-per Refiners Limited, since the refinery was established in 1931, have been described in previous papers ( 1,2). Since then the refinery has treated the entire copper output of Noranda Mines Limited and Hudson Bay Mining & Smelting Company Limited. With the commencement of production in 1956 at Gaspe Copper Mines Limited, this copper has also been refined. From the start of operations to the end of 1958, the following had been refined: copper, silver, gold, selenium and tellurium.Construction of new buildings and additions to other buildings have been needed to handle increased receipts. The refining capacity has been increased from 112,000 tons of copper per year to a total of 236,000 tons per year.The refinery is located at Mont-real East, Quebec, close to railway and highway facilities. Incoming materials and shipments, with some small exceptions, are handled by rail. Some finished products are sl1ipped by industrial flatcar to the adjoining plants of Canada Wire & Cable Company Limited and Noranda Copper & Brass Limited."

Jan 1, 1960

By David A. Edgecombre

This paper discusses modern practices in the extrusion of steel. Particular emphasis is given to a description of the Ugine Sejournet method of extrusion, involving the use of glass as a hot work lubricant. Other methods are also mentioned. A brief history of extrusion is presented; present practices in the quality extrusion of tubing and solids are described; and the future potentials of the) process as a tonnage producer are briefly discussed. The advantages of extrusion and the reasons for the use of a glass lubricant, as well as the various methods of using glass, are given. The process, as described, is being used in the manufacture of large commercial quantities of stainless steel tubing and sections. This extrusion process is an essential and unique means of forming such atomic-age materials as titanium, zirconium, molybdenum and other super alloys all of which are materials required in the creation of nuclear installations.

Jan 1, 1963

The use of roof bolting gave promise of substantial economic benefits to Continuous Miner operations at Michel Colliery. As the first step in the adoption of bolting, 142 anchorage tests, employing six types of anchor shells, were made in three mines. Significant differences were found in the anchorage capabilities of the various shells and the various roof rocks. Introduction S PORADIC attempts at roof bolting had been made at Michel Colliery over a period of ten years. Results were indifferent or inconclusive. A concerted effort was not made, because a compelling need for bolting did not exist. By 1962, however, the advent of Continuous Miners had brought a new significance to roof bolting and, at the same time, the increasing price and scarcity of mine timber made bolting materials more competitive in cost. A fresh appraisal of bolting, therefore, became justified and necessary. The potential benefits of roof bolting at Michel are several.

Jan 1, 1963

By Jirí Faltus

The paper deals with studying the impact of structural properties and anodizing of surface on the corrosion properties of extruded rods from commercial aluminium alloys: AA6082, AA6262, AA6012, AA2007 and new lead-free aluminium alloys AA6023, AA2015 and AA2111B. Samples were exposed to the corrosive atmosphere NSS, AASS in the chamber by EN ISO 9227. Surface of samples were either in the original state or anodizing by selected mode. The depth of corrosion attack and the form of corrosion attack are evaluated depending on the type of alloy, the metallurgical condition and surface treatment of the samples.

Jan 1, 2015

By Patrick E. Cavanagh

"A pilot shaft furnace was operated for one year at Steep Rock to produce special high-grade products from coarse ore, using lignite as fuel. The furnace is 10 ft in diameter and 60 ft high. When operated to heat coarse Steep Rock ore to drive off combined water and give a 64-per-cent-Fe product, the fuel consomption was 900,000 Btu's per long ton of product. The furnace was run in this way from September 1966 to January 1967 to establish the technique of feeding and discharging the furnace and controlling the gas composition and temperature. The furnace is similar in operation to a lignite water gas producer containing a large proportion of catalytic iron oxide. Steam injection is used to control the temperature. The product was tumbled in a rotary trommel to stabilize it. The resulting fines could be fed to the conventional pellet plant at Steep Rock. The furnace was next operated to make 77-per-cent-Fe metallized coarse ore. Several major modifications in de-sign were made and the furnace was successfully operated for short periods to maintain the required conditions to remove 75 per cent of the oxygen from the ore to give a 75-per-cent-reduced product at a grade of 77 per cent iron. The furnace cooling zone was operated under positive pressure, with internai alkaline water sprays to cool the charge. The product was discharged from the open bottom of the furnace without serions reoxidation. The metallized ore was magnetically separated from the discharge. Most of the charred lignite discharged along with the ore is re-cycled. Fuel requirement was 11,000,000 Btu's per long ton of product. This metallized coarse ore is intended for blast furnace feed. A short test run was carried out to establish the conditions for making a highly reduced melting stock for steel furnaces. To achieve 90 per cent reduction and over 90 per cent Fe, the furnace must be slowed down so that the production rate is about one-half the rate when making a 75-per-cent-reduced metallized product. Fuel requirement is 15,000,000 Btu's per long ton of product. The simple shaft furnace developed is similar to the top half of a blast furnace, with some major modifications to allow discharging into the open air. This Low Temperature Blast Furnace program has been technically successful and has resulted in making data available for the design of a commercial plant. Study of the commercial feasibility of large-scale production of metallized coarse ore at Steep Rock is still continuing."

Jan 1, 1968