Search Documents

By Donald L. Mordell

Introduction A very large part of the world's fuel resources are in solid form, as various grades of ?coal, but an increasing proportion of fuel demands on this Continent and else-where are having to be met by liquid fuels. Convenience and, in many cases, cost weigh heavily in favour of the liquid: fuels, and there are many fuel burning applications where the use of coal would be impractical, such as for automotive or air transport. By extrapolating the present trends one might conclude that, in future years in Canada and the United States, coal will be used only in a few power stations close to coal fields. If such a state of affairs should arise, it will obviously prove embarrassing to those accustomed to make their livelihood from the winning and marketing of coal, but it is perhaps not so obvious that it must also prove an embarrassment to the nation. The major reasons for this are two in number. Firstly, if present coal production is to be replaced by oil production, a large capital expenditure is necessary, which must inevitably be paid by the consumer; and secondly, in times of emergency, large amounts of oil fuels are required for military purposes which cannot be achieved with solid fuels. It is obviously unwise, therefore, to discontinue the use of coal for those non-military jobs that it can do. If we examine the major fuel markets we find that there are three: Domestic heating Steam generation Transport by air, sea, and land For domestic heating, the extreme convenience of oil, in spite of its greater cost, has captured much of the coal market.

Jan 1, 1952

By P. C. M. Knops, K. Rijnsburger, R. M. Santos

To overcome the challenges of mineral CO2 sequestration, this work utilizes a unique proprietary Gravity Pressure Vessel (GPV) reactor technology, and focuses on reaction products of high economic value. The GPV provides intense process conditions through hydrostatic pressurization and heat exchange integration that harvests exothermic reaction energy. Here, laboratory-scale tests of the envisioned process was performed in tubular and continuously stirred tank reactor (CSTR) autoclave reactors. The mineral used was Olivine (~Mg1.6Fe2+0.4(SiO4) + ppm Ni/Cr), although asbestos, steel slags and oil shale residues are also under investigation. The effect of several process parameters on reaction extent and product properties was tested: CO2 pressure, temperature, residence time, additives (buffers, lixiviants, chelators, oxidizers), solids loading, and mixing rate. The products (carbonates, amorphous silica and Chromite) were physically separated (based on size, density and magnetic properties), characterized (for chemistry, mineralogy and morphology) and tested in intended applications (e.g. as pozzolanic carbon-negative building material). Economically, it is found that product value is the main driver for mineral carbonation, rather than, or in addition to, the sequestered CO2. The approach of using a GPV and focusing on valuable reaction products could thus make CO2 mineralization a feasible and sustainable hydrometallurgical process.

Jan 1, 2015

By R. O. Suzuki, S. Natsui, R. Nashimoto, T. Kumagai, T. Kikuchi, H. Takai

A newly developed computational fluid dynamics model based on a multi-phase particle simulation is presented for predicting the entrainment behavior of liquid metal into slag due to rising single bubble. By comparing results calculated using this model against experimental data, it was found that the transient behavior of bubbles and the two immiscible liquids can be accurately estimated by this method. The rupturing of the thin water film surrounding the bubble was less reliably predicted, but this 3-dimensional unsteady numerical model still nevertheless provides valuable new information for directly predicting the change in the liquid-liquid interface over time. This model predicted the Young-Laplace pressure, and the interface shape was simulated with volume conservation using this model as opposed to the conventional particle method. This simulation model can calculate both of dispersed phase and continuous phase seamlessly.

Jan 1, 2015

By J. S. Kirkaldy, W. J. Slater, G. R. Mason

Activation analysis for copper and manganese in 10 mg samples machined from aluminum-base diffusion couples has been used in the study of ternary diffusion in the Al-Cu-Mn system. The accuracy, economy and convenience of the method are considered to be very competitive with other methods for analysis of such small samples. Neutron-activated aluminum-zinc alloys in the range from 10 per cent to 100 per cent zinc have been equilibrated with a known volume and the vapors subsequently condensed and collected. The vapor pressures relative to pure zinc (the thermodynamic activities) have been determined at 550°C' by recording the relative count of /'-rays from zn65 in the collected samples. The method is a sensitive one, although subject to serious obstacles to experimental accuracy.

Jan 1, 1961

By T. G. Ewart

INTRODUCTION FOR THE purpose of this paper, western bituminous coal is defined as steam coal produced in Alberta and southeastern British Columbia for sale primarily to railways and industries. Before examining present and future markets of this industry, it is proper to review briefly financial and operating conditions within the industry. The report of the Royal Commission on Coal, 1946, supplies financial data from which some conclusions may be drawn. In 1944, the industry as defined above had share capital of $24,886,696. In the fifteen years 1930 to 1944, inclusive, the industry produced: 44,364,211 tons of coal. The profit on this tonnage amounted to $4,678,382.58, which represented 10.6 cents per ton of production. Miscellaneous earnings increased the amount available for dividends to shareholders to a total of $8,487,952.41, which is equal to, 19.1 cents per ton of production. Dividends actually paid in this fifteen-year period amounted to $12,332,040.64, which represented an annual average rate of 3.40 per cent on share capital. It is worthy of note that, in 1944, the net current position of the industry, including investments, was $8,753,874.51. The writer believes that the financial position of the industry with respect to capital, current financial position, and net earnings, has not significantly changed from the fifteen-year period out-lined above. The figures quoted indicate the following situation: (1) The western bituminous coal industry is adequately financed. (2) The industry has followed a conservative dividend policy and has accrued funds for contingencies. (3) The industry has sold its production at very reasonable prices as evidenced by its moderate earnings per ton of production.

Jan 1, 1951

By E. Viljamaa

In this research, earlier developed information integration method and novel web technologies are applied to intensify infrastructure construction process control. The applied method uses semantic methods to integrate scattered information that is later on exploited by process management using state-of-the-art web technologies. The applied method and web technologies not only improve the process management situation awareness by integrated up-todate multi-source process data but also provide platform independent access and visualization tool for process data. Utilization of such technologies potentially lead on cost savings, make processes safer and also more environmentally friendly. The integration method also enables intelligent queries to the integrated data making possible to use machine based inferring to the data.

Aug 1, 2013

By David W. Mogk, Tamara Darsow, Macgregor L. Fogelsong, Robert M. Hunter, Frank M. Stewart, Edwin H. Abbott, Courtney A. Young

Abstract: Development of cost-effective techniques for recovering precious metals from their ores has been the goal of metallurgists for hundreds of years. Today, metallurgists are increasingly called upon to design processes for ores that are refractory to conventional recovery techniques. These challenges and the addition of environmental costs (including site remediation) to the total cost of mining have stimulated a search for alternatives to conventional processes, such as cyanidation. This paper describes the progress made to date in development of an innovative alternative to cyanidation, termed bisulfide leaching, for extracting gold, silver and platinum-group elements from refractory ores and concentrates. While bisulfide leaching can be implemented abiotically, significant benefits accrue from its practice as a bioprocess that integrates the steps of precious-metals liberation and extraction. In many applications, bisulfide leaching appears to offer significant advantages over the traditional cyanidation process. Dissolved bisulfide and hydrogen sulfide are much less toxic than dissolved cyanide and hydrogen cyanide. Recommended workspace exposure limits and harmful concentrations for hydrogen sulfide gas are higher than those for hydrogen cyanide gas. While the facilities required to practice the bioprocess on an industrial scale would be similar to that of cyanidation plants, chemical reagent costs could be 80 percent less. The bioprocess may also offer advantages in the leaching of ores and concentrates that are not amenable to cyanidation. For example, bisulfide leaching of ores containing carbonaceous material may produce higher gold recoveries if the "preg-robbing" characteristic of the material can be controlled biologically or with dissolved sulfide binding. Moreover, in that precious metals are much more soluble than base metals in bisulfide solutions, bisulfide leaching offers distinct advantages over cyanidation for selective dissolution of precious metals from base-metal concentrates. Thus, the bioprocess uses the natural sulfur cycle to mitigate pollutant production and to enhance precious-metals recovery.

Jan 1, 1998

By J. W. Jefferies

"Plant availability up 13%, production output up 40%, tons per employee up 15% and labor turnover down 52%. One mine manager states these were direct spin offs from the work being done to qualify for a safety award in the program known as the ""IMSRS 11 over a three-year period of time. ""Of Course"", stated this manager, ""these were in addition to an 87% reduction in our disabling injusry frequency rate.”Officially known as the International Mine Safety Rating System or the Five Star Mine Safety Rating, a new approach to mine safety is being used with enthusiasm by a significant number of mines in Canada, the U.S., Australia, Chile, Indonesia, the Philippines and South Africa. Significant results are coming into the International Loos Control Institute from over 125 mines from these countries.The program is built around a mine safety audit system that gives positive recognition to a mine at 5-step intervals along the way, (a star with each step attained). The Institute has licensed auditors in locations in Canada and the U.S. available to audit.It is believed the success of this program is the result of the premise upon which the program is based. The results being achieved are due to the concept that a modern, well-managed mine safety program maintains the basic foundation of a complete management system. When properly implemented, it reinforces those factors common to production, quality and safety. (Attitude - skill - knowledge - fitness - structure - machine - equipment - materials and processes). The IMSRS contains elements that reinforce all these factors. It uniquely treats safety as part of the ""right way"" to do the job and not just the ""safe way"" as a distinctly separate entity. Mines using this program now recognize that many of the older safety techniques were not necessarily the right way or the most efficient way to do things. It appears that this new approach to mine safety is a new avenue for the attainment of management's real goals for being in business, and at the same time achieves optimum support for the important target of safety and health for the mine worker."

Jan 1, 1983

By V. Concha, M. Hashemzadeh

"The objective of this study was to gain a better insight into the kinetics of chalcocite leaching in an acidic ferric sulfate media. Chalcocite leaching in acidic media is known to occur in two sequential stages, with the first stage being much faster than the second. The leaching residue from the first stage is typically assumed to be a covellite type of material. This study hypothesized that the mineralogy after the first-stage leaching varies in response to different leaching conditions. We investigated the dependency of the mineralogy of the first-stage leaching residue on temperature and initial ferric concentration. The experimental results showed that chalcocite leaching behavior altered upon temperature and initial ferric concentration. A proposed combined reaction model was found to be able to describe the experimental data. The first stage was described very well by the shrinking core diffusion model while the second stage was described very well by the shrinking core chemical reaction model. This finding has important implications for mine operations to manipulate leaching conditions to create the desirable leaching kinetics.INTRODUCTION The kinetics of chalcocite leaching in sulfate media has been extensively studied (Cheng & Lawson, 1991; Fisher, 1994; Fisher, Flores, & Henderson, 1992; Niu, Ruan, Tan, Jia, & Sun, 2015). Sullivan (John D. Sullivan, 1930) proposed a two-stage process for chalcocite leaching in an acidified ferric sulphate solution. The two-stage leaching of chalcocite is presented as the following reactions:"

Jan 1, 2017

By Eduardo A. Pérez, Alejandro R. Alonso, Rosa María Luna-Sánchez, Gretchen T. Lapidus

Rare earth elements have been widely used in various sectors, from the aerospace and steel industries, to electronic applications, particularly in displays and batteries for portable devices. The high demand for newer and better equipment, such as cell phones, tablets and lap tops, has increased the consumption of the rare earth elements and at the same time the need for its recovery from electronic wastes. For that reason, the recycling of batteries is important, principally the Ni-HM batteries, due to their elevated content of rare earths elements, in addition to the high concentrations of cobalt and nickel. The current processes are based on dissolution in strong acid solutions (sulfuric acid concentrations from 2 to 4 mol/L), and temperatures from 30 to 90°C. In the present work, electrodes from spent Ni-HM batteries were leached using 1 mol/L H2SO4, in the presence of ozone as the oxidant, where recoveries of 96% for La, Ce and Nd were obtained at room temperature. The separation of Ni and Co from the leach solutions was performed using an electrochemical reactor, after which rare earth elements were precipitated, obtaining a mixture of its hydroxides with impurities below 1%, according to EDS analysis.

Jan 1, 2014

By Hrayr Agnerian

The fair market value of an exploration property is determined by its potential to host a mineral deposit. This potential is gauged by the results of previous exploration, exploration stage, meaningful past expenditures and remaining targets that are not yet tested. Values of exploration properties can be viewed as distinct points in a three-dimensional space defined by orthogonal axes, namely: Exploration Stage (x-axis); Cumulative Expenditures (y-axis); and Property Value (z-axis). In general, these values are estimated by applying activity factors on previous exploration expenditures, e.g. an activity factor of 100% for an active property with good potential and a factor of 50% for an active property but past expenditures have not upgraded the property. At certain periods, a market factor may also be applied to reflect the activity of mineral property acquisitions. For properties that do not exhibit any exploration potential, only nominal values are applied.

Jan 1, 1996

By F. Rashchi, A. Ghahreman, J. Moghaddam, S. Karimi

"In this work, the kinetics of ferric-ferrous redox reaction on a passivated sphalerite electrode is studied by the application of chronoamperometry method in 0.5 mol L-1 H2SO4 solution. The electrochemical behaviour of ferric and ferrous couple was investigated on two sphalerite minerals acquired from two different geological regions (Iran and Canada). The carbon paste electrode (CPE) of sphalerite was initially prepared and passivated in 0.5 mol L-1 H2SO4 solution and after reaching the steady-state condition, ferric and ferrous sulfate solution was added. The registered current density differences between the current density of the passivated electrode and that of the electrode in the iron salts added solution were interpreted for kinetics of ferric-ferrous reduction-oxidation reaction. The equilibrium potential for ferric-ferrous couple on sphalerites surface was about 500 mV vs. Ag/AgCl. The exchange current density (i0) for ferric-ferrous redox reactions on the sphalerite samples had the same magnitude of 10–6 A cm–2. The electrochemical impedance spectroscopy (EIS) measurements at 550 mV vs. Ag/AgCl illustrated that sphalerite oxidation was controlled by two charge transfer process in both of Fe-free and Fe-containing solutions. The charge transfer resistance remarkably decreased when Fe salts added to the 0.5 mol L-1 H2SO4 solution, owing to the ferric-ferrous redox reactions being the predominant reactions on sphalerite surface.INTRODUCTION Direct atmospheric leaching processes for sphalerite concentrates are performed by reduction of an oxidant (e.g. ferric ion and oxygen) and oxidation of sphalerite to zinc ions. Oxygen could be an oxidizing agent as well, but the concentration of oxygen is very low in the solution. The role of ferric ions is predominate in this oxidation (Babu, Sahu, & Pandey, 2002). The oxidation reaction for sphalerite in the presence of ferric in can be presented as follows (Lampinen, Laari, & Turunen, 2015):"

Jan 1, 2017

By R. Niechcial

As populations grow and industry expands, the limited fresh water resources available are increasingly under stress. This situation creates conflict between communities and industry; and the sustainability of both is threatened. The symbiotic relationship between community and industry highlights the need to develop innovative solutions to these water shortages. The sea may hold the key to providing the resource to permit the development of industry, the sustainability of communities, and the protection of the dwindling legacy water resources around the world. Desalination technologies have developed to where it is now economically viable to create industrial and potable water quality from seawater. Nowhere is this development more important than in the arid region of Northern Chile, where high copper prices have encouraged a boom in mine development.

Jan 1, 2007

By Alessandro Navarra, Amir Arash Rafiei, Kristian Waters

Mathematical programming (MP) is fundamental to systems engineering and operations management, but has not been widely adopted by mineral processors. The current paper presents an interdisciplinary approach, using MP to incorporate basic notions of mass balancing into an optimization framework. The optimization is typically related to economic profitability. Two- and three-product formulas are extended to give formal descriptions of alternate modes of operation, and a global representation of the concentrator. At this global level, the framework may assist plant managers to make tactical decisions based on incoming feed data. The MP framework is demonstrated through sample calculations describing a lead-zinc concentrator.

Jan 1, 2015

By Francisca San Martin, Tomas Vargas, Willy Kracht

"In Cu-Mo deposits it is usual to find considerable amounts of pyrite (FeS2). When processing this kind of ore by flotation, pyrite is rejected using lime to increase the pH to alkaline conditions (pH ~10.5). In the case of using seawater without pre-processing, i.e., raw seawater, the lime consumption increases dramatically and the recovery of molybdenite drops due to the precipitation of magnesium hydroxide on its surface. In order to avoid these negative effects, alternative ways of depressing pyrite should be considered.The current work introduces the use of Acidithiobacillus ferrooxidans, bacteria commonly used in bioleaching, as an alternative to depress pyrite in seawater flotation. The paper presents the results of biodepression in three systems: fresh water, water with added sodium chloride at 35 g/L (which corresponds to the salt concentration in seawater ) and seawater. The results show that it is possible to bio-depress pyrite with A. ferrooxidans in natural seawater pH (7.8-8.2). A similar behaviour is observed when running the experiments in fresh water, and in water with sodium chloride added.INTRODUCTIONWater is a scarce but essential resource for human development. The main reason for this scarcity is that, although 70% of the earth's surface is covered with water, only 3% of the total is fresh water and an important part of this water is frozen, so that only 1% of fresh surface water can be used for human activities. In Chile, most of the mining activity is concentrated in the north of the country, located in the Atacama Desert, considered the world's driest desert. That is why some mining companies have chosen to use seawater in their processes. For example, Esperanza (Antofagasta Minerals), and Sierra Gorda (KGHM International) use raw seawater in their flotation processes."

Jan 1, 2016

Slurry flow, including flow through the charge, through the discharge grates, along the pulp lifters and its discharge from the mill is an important contributor to the efficiency of the grinding process within a SAG mill. Poor transport of finer ground material can adversely affect grinding leading to excess energy consumption and over-grinding of fine material. This paper extends a 1-way coupled DEM-SPH method to three dimensions and applies it to a 1.8 m diameter by 0.6 m long AG/SAG pilot mill. This provides detailed information on the internal flow of slurry within a SAG mill, including the prediction of dry regions and of slurry pooling. Full 3D analysis also allows the pulp flow patterns into and out of the mill via pulp lifter chamber to be investigated.

Jan 1, 2012

By G. P. Holmes

"Bell Copper is situated (Latitude 55°0''N, Longitude 126°14W) on Newman Peninsula on the east side of Babine Lake at an altitude of 2,450 feet above sea level. The mine site is approximately 170 miles north west of Prince George and 40 miles east of Smithers. Access to the property is by way of 30 miles of paved road to the Village of Granisle on the west shore of Babine Lake and then a further 9 miles of unpaved road to Bell Copper's west dock. The two mile lake crossing is made using a tug and barge. A compressed air bubbler system maintains an ice free channel for the barge during the winter months.Temperatures range from summer maximums of around 32 °C to winter minimums in the region of minus 40°C. Long periods in winter may be spent with temperatures in the range of minus 15""C to minus 28°C. Freezing temperatures usually start in October and last for six months. The lake normally freezes over in mid December and the ice breaks up in mid May. Snow accounts for approximately two t11irds of the annual precipitation of twenty-one inches."

Jan 1, 1976

By K. Fagerlund, L. Rosenback, T. Mäkinen, Y. Anjala

This paper deals with the nickel smelter and refinery concepts Outokumpu has applied at Harjavalta and several other plants. Also other process routes and modifications developed and tested by Outokumpu during the recent years are highlighted. Outokumpu started nickel production in Harjavalta in 1959. Until 1995 the Flash Smelting - Peirce-Smith (PS) converting route was applied. High grade nickel matte from the converting step was further refined by means of leaching and electrowinning to produce cathode nickel. In 1995 the nickel production capacity was increased from 17 000 t/a to 52 000 t/a based on the Direct Outokumpu Nickel Smelting Process (DON). In the DON process PS converting is eliminated and high grade nickel matte with low Fe-content is directly produced in the flash smelting furnace (FSF). Metal values from the smelting slag are recovered in the electric furnace (EF) as iron containing Ni-matte. The DON process can be operated with either two matte concept, where high grade FSF matte and EF matte are produced, or a single matte concept, where EF matte is recycled to the smelting furnace and thus only one type of high grade matte is obtained. The additional refinery capacity at Harjavalta is based on hydrogen reduction producing.

Jan 1, 2005

"ALTHOUGH Canadian metallurgists have long been active in research, the scope of the work was somewhat limited until the be-ginning -of World War II. The rapid industrial development of Canada during the past ten years has been accompanied by .a similar upsurge in research. However, the wide geographical distribution of the research centres has made it difficult for the individual research workers to meet together and to exchange ideas or even to learn what projects .are being investigated or the nature and extent of the facilities available for work of this kind.The purpose of the present symposium is to assemble data relating to projects under investigation and the facilities employed at the various metallurgical research laboratories in Canada, thus providing some measure of correlation so that workers in different locations may learn what kind of work •is being .done at other points throughout the country.In reporting the symposium it has not been possible to reproduce the papers in full, but excerpts have been selected that give the essentia1 data."

Jan 1, 1952

By W. S. Szolga, M. Moser, M. D. Soderstrom, L. Cohen

"CYANEX® 272 is a phosphinic acid-based solvent extraction reagent used commercially since the early 80’s to recover and purify cobalt from sulfate solutions. Historically, the design of CYANEX 272 circuits has involved the selection of an optimal pH profile during pilot-scale testing using mixbox pH control. The desired pH profile is required to be carefully controlled in the same manner during commercial operation. To assist operators in the design and optimization of their circuits, Solvay developed CYANEX 272-specific solvent extraction modeling software, which has enabled determination of the ideal pH profile and staging configuration. Solvay’s recent advances in modeling capabilities have allowed the simulation of circuits without direct mixbox pH control. Modeling has indicated that circuits operated without direct pH control can achieve the desired metal separation while simplifying the commercial operation significantly. This paper reviews a number of potential circuit configurations for the use of CYANEX 272 and demonstrates the separations achievable under the right design and operational conditions, some of which have historically been considered too difficult.INTRODUCTION CYANEX® 272 is a phosphinic-acid based reagent designed specifically for the separation of cobalt from nickel by solvent extraction from weakly acidic sulfate solutions (Rickelton, Robertson, & Burley, 1982; Rickelton, Flett, & West, 1984; Rickelton & Nucciarone, 1997). Following commercial introduction in the 1980’s, CYANEX 272 has been used in a number of hydrometallurgical flowsheets for cobalt purification and/or recovery. CYANEX 272 metal extraction occurs by means of a cation exchange mechanism. Extraction of a divalent metal ion M2+ is represented by the following equation where RH represents the CYANEX 272 ligand and MR2 represents the ligand-metal complex."

Jan 1, 2017