Search Documents

By STEPHEN V. FORGERON

The Loch Lamond celestite properties in central Cape Breton Island were mined by Kaiser Celestite Mining Limited from 1970 until 1976. Poor market conditions in J976forced operations to cease. Kaiser holdings included the Lake Enon, MacRae and A mac prospects. A total of about 272,000 tonnes of raw celestite have been mined. Celestite deposits are situated in the Loch Lamond Basin, specifically in Lower Windsor sedimentary rocks. Of the five formations in the Lower Windsor Group, celestite is found in the upper four. Celestite in the Enon Formation occasionally replaces shale that separates stromatolitic dolomite columns; elsewhere in the formation it occurs in association with siltstone and gypsum. Jn the B2 Limestone Formation celestite fills pores or grades between limestone and gypsum. It replaces both limestone and silty limestone conglomerate in the Loch Lamond Formation; this limestone is of unusually high grade (60 to 70% SrSO,J for the area. Evidence indicates that the Uist Formation may hold important celestite reserves. Original celestite mineralization probably resulted from evaporation of seawater on mudflats or 'sabkhas'. Secondary mineralization also may have occurred. Strontium ions could have been leached from pre-existing concentrations and overlying gypsum, moved downdip in groundwater and combined with sulphate rich waters to deposit as celestite in porous B2 limestones.

Jan 1, 1984

By I. Yutronic

Compañía Minera Doña Inés de Collahuasi's (CMDIC) Concentrator Plant is located at 4300 meters above sea level, approximately 2000 kms north from Santiago, Chile. The concentrator has three grinding lines. Each one, Lines 1 and 2, have one SAG mill at the primary grinding stage followed by a secondary grinding and classification stage consisting of one ball mill, two hydrocyclone batteries and a sump with two pumps. Line 3 has one SAG mill (Gearless Mill Drive), followed by a secondary grinding and classification consisting two ball mills, four hydrocyclone batteries and a sump with four pumps. Average throughput for these three lines is 150 Ktons per day. Peak values of 180 ktons per day have been achieved. Since late 2008 and throughout 2009 and 2010, Operations and Automation areas developed an optimization program for the grinding process, considering the implementation of Model Predictive Controllers (MPC) for the three SAG mills, and later, extending MPC to the secondary grinding and classification stages. The implementation of a MPC solution was based on stability considerations (high variability of the SAG process, high interaction between sump level control and classification efficiency, etc), requirements for an automated and consistent operation, the need to maximize throughput under timevarying scenarios and, in the long term, optimization of grinding process considering Specific Energy Consumption, among other parameters. MPC solutions had proven control robustness and strong optimizing capabilities in terms of helping in discovering new operational points and so achieving all of the aforementioned goals. On the first stage of the program, MPC implementation considered identification of dynamical process control models based mainly on historical data, in order to know the impact of a group of Manipulated Variables over Controlled Variables. Also, the impact of measured Disturbance Variables was modeled in order to take into account the high impact and interaction of these variables over the processes. At the end of this stage, 4 controllers were successfully operating for the 3 SAG mills and the secondary grinding and classification process. In response to challenges made by the working group, the second stage of the development of control applications in the grinding process required to achieve a design and implementation of a solution capable of governing the milling process, in addition to stabilization and optimization of both processes (SAG milling and secondary grinding), to integrate from a point of view of process control and automation. Therefore, in the second stage, MPC performance was continuously monitored and optimized through advanced tuning, inclusion of more process models (with proper step tests), redefinition of specific optimization criteria and adjustment to new process needs. Finally, successful MPC implementation at Collahuasi has proved that fast development and deployment of process control solutions is possible and allows immediate process stability, higher throughput, specific energy consumption reduction, and successful product size control, among many others.

Jan 1, 2012

By P. R. A. Andrews

"A sample of flotation feed from Bakertalc Inc., High water, Quebec was subjected to flotation evaluation to improve the recovery of talc. A number of alternative frother/collectors and depressants as well as flotation parameters including pH, conditioning time, frother/collector concentration and pulp density were assessed. In addition, the possibility of using a size coarser than that currently employed for flotation (95% minus 50 um) was investigated.As far as possible, a laboratory duplication of the present circuit arrangement was folio wed so as to minimize the cost of any changes. The best results obtained were a concentrate analyzing 95.96% acid insol for a recovery of 65.98% after four stages of cleaning. With recirculation of cleaner tailings, the recovery would be higher.The possibility of using an alternative method, based on the natural ability of talc to float unaided by a frother/collector, was briefly explored with encouraging results.IntroductionBakertalc lnc ., located in the eastern townships at Highwater, Quebec, Is approximately 140 km east of Montreal near the Vermont, U.S. border. Originally called Baker Mining and Milling Co. Ltd., it has produced pulverized talc products since 1938(1 ), although records show that talc was mined in the area as early as 1871(2). Feed to the mill originally was obtained from local deposits, but since 1952 the van Reet mine near south Bolton, approximately 25 km from Highwater, has been the source of ore .In 1957 a Raymond high -side roller mill was installed which enabled production of a greater range of talc products and, in 1960, new crushing equipment and a dryer were added. Other additions to the mill were the introduction of wet magnetic separation, although this was later discontinued, and flotation to produce high-grade talc concentrates."

Jan 1, 1985

By L. Gutierrez, M. Pawlik

The rheology artificial mixtures of bitumen with fine quartz of varying bitumen content, as well as actual oil sand ores, was investigated under different physicochemical conditions (pH, temperature). All rheological measurements were conducted using a Haake Rotovisco VT550 rotational viscometer, connected to a fixture specifically designed to measure properties of settling suspensions. It was found that at low bitumen contents (1 %, wt.) the pH of the slurries was the most important parameter that controlled the rheology of quartz-bitumen slurries. At higher bitumen contents (10%, wt.), it was a combination of high temperature and high pH that gave the lowest apparent viscosities and yield stresses of the model mixtures. These model observations correlated well with the rheology data obtained for slurries of actual oil sand ores. The overall results were discussed in terms of aggregation-dispersion phenomena between bitumen and mineral particles.

Jan 1, 2009

By Amir Karami, Derek Kinakin, Catherine Schmid

The Mathews Stability Graph Method (Mathews et al., 1981) has been used by geotechnical engineers and mining engineers for over 40 years to estimate the performance of longhole open stopes in underground mines. The method is widely used and accepted by practitioners because it is relatively simple to use and can be modified to account for observed performance at a given mining operation. While the simplicity of the method increases its accessibility and utilization, it does not intrinsically account for variability in the various inputs, including rockmass quality, structure, stress, or stope orientation. This paper presents a modified approach for the Stability Graph Method, whereby Python scripts are used to process available geotechnical datasets and combine them with actual or potential distributions of Q parameters, induced stress, structure, or stope orientation. The resulting Stability Numbers are then plotted as a contoured distribution on the Stability Graph.  This allows the practitioner to quickly incorporate large datasets into the analyses, while also developing an understanding of how variability in rockmass quality, induced stress, structure, or stope orientation could affect stope stability.  This paper presents the fundamental principles of the Stability Graph method, the Python script and workflow, and two case studies to demonstrate the utility of the tool.

Oct 1, 2024

By D. Chadwick, J. W. Matousek

Between 1860 and 1890 -- from the time of the American Civil War to the last decade of the 19th Century -- nickel production in North America was dominated (even monopolized) by the output of the industrial complex of the Gap Nickel Mine near Lancaster, Pennsylvania and the American Nickel Works in Camden, New Jersey. In some years, from one sixth to one third of the world's metallic nickel supply came from this enterprise. Mining and smelting were conducted at Lancaster; a matte of high iron content was shipped to Camden for pyrometallurgical and hydrometallurgical refining to produce nickel metal, copper sulfate, and cobalt oxide. The high purity nickel product was rolled into sheet for marketing, primarily for coinage, as nickel had few other uses at that time. The undertaking experienced all of the problems that face the mining and metallurgical industries of today: declining reserves, high labor and fuel costs, high transportation costs, fluctuating demand and prices, pollution concerns, and foreign competition. The technical features of the geology; the mining, smelting, and refining operations; and some of the economic aspects are assessed. The view is taken from that of the present time -- seeking those lessons from history that we are supposed to learn or face the prospect of repeating the mistakes of the past.

Jan 1, 2005

By David Ulrich Furrer

Materials and manufacturing processing technologies have played an important role in the development and capabilities of nearly all manmade products. Market drivers for fuel efficient, low cost, environmentally friendly, more capable transportation has given rise to significant materials challenges and subsequent developments. The rate of improvement and implementation of new commercial products can be limited by the rate of new materials and process technology development and qualification. As many materials are being designed for unique requirements and even location-specific unique properties, the implementation of tools and methods to enable rapid characterization and validation of material definitions and design systems must also be accelerated. A review of new integrated material, manufacturing process and component designs, engineering processes and emerging tools and methods will be discussed. The linkage of computational materials science and engineering into component design will also be discussed along with the challenges and opportunities for further growth and application of integrated computational materials engineering (ICME).

Jan 1, 2015

By R. C. A. Thurston

Introduction A mechanical spring has been .defined by Wahl ( 1) as 'an elastic body whose ?primary function is? to deflect or distort under load, and which recovers its original shape when released after being distorted'. Most material bodies are elastic to some extent ? and will deform under load, but they are seldom regarded as springs since this is not their primary function. The principal applications of springs are the absorption of energy and the mitigation of shock, the support cf moving masses or the isolation of vibration, and the provision or measurement of definite loads or torques. A large number of spring types have been developed to serve these purposes and to meet the different operational requirements; they range from the large semi-elliptic leaf suspension spring to the delicate watch hairspring. The springs of most importance in machine design, however, are the helical round-wire compression or tension types. They are made in a wide variety of sizes and are used in tremendous quantities, mainly because of their low cost, their compactness, and their relatively high efficiency. Their field of application is as broad as that of machine design itself, but the bulk of production is almost certainly for suspension systems of vehicles such as automobiles, freight and passenger cars, and mine cars, and it is with the last of these applications that this paper is primarily concerned.

Jan 1, 1951

By W. Lodge, G. Rasmussen

"The carbon-in-pulp (CIP) process has been the dominant gold recovery technology since the 1980s. During all this time carbon measurement, and control of the carbon transfer pumps has been largely manual in nature. Such manual operation inevitably limits process efficiency, potentially resulting in higher gold solution losses, and higher cost of circuit operation. Based on the authors’ experience, average plant solution loss is in the range of 0.02-0.03 ppm Au, as opposed to the general industry target of 0.01 ppm Au or less. Gekko Systems, in conjunction with Curtin University’s Gold Technology Group, has developed a carbon concentration meter, the ‘Carbon Scout’ meter. The meter automatically measures carbon concentration in all tanks, providing more frequent and more precise data. Combined with SIMCIL, a CIP circuit process model which is used to determine the optimum set points for the circuit, the meter should ensure lower gold solution losses, and more efficient operation of the carbon circuit. This paper will review they critical factors for good carbon management, the development of the meter and results from the first plant installation. Additional benefits of the Carbon Scout, including improved health and safety and the opportunity to measure other key variables in the leach/adsorption circuit from one central location will also be described.INTRODUCTION The carbon-in-pulp (CIP) process was first introduced to the gold industry in the early 1950s at the Carlton Mill in the USA (Fast, 1988), with the modern version of CIP becoming fully developed with large scale installations in South Africa in the late 1970s (Laxen, 1982). CIP quickly became the technology of choice for new operations, and for the retrofitting or upgrading of existing operations. In the 1980s the carbon-in-leach (CIL) circuit configuration became the process design of choice due mainly to its lower capital costs. With 40 years of operational experience, CIP/CIL for gold recovery is now mature a technology, whose operations and limitations are well understood. To extract further efficiencies from such technologies, by improving recoveries and/or reducing operating costs, is challenging and may require new approaches to circuit management. Gekko Systems, in association with the Gold Technology Group at Curtin University, has developed the Carbon Scout, an automated carbon measurement device. This device replaces manual measurement of carbon concentration in carbon adsorption tanks, providing more frequent and more accurate data for control of the CIP process. Data from the Carbon Scout can be used to automatically control the carbon forwarding pumps."

Jan 1, 2018

By P. J. Sylvester, S. J. Piercey, S. Maloney, S. M. Brueckner, L. Pilgrim, D. Hyde, G. Ogilvie

The 1806 zone is part of a Au-rich volcanogenic massive sulfide deposit at the Rambler Camp on the Baie \/erte Peninsula, northwestern Newfoundland, and is characterized by high Au grades (3.97 g/t), relatively low Cu and Zn grades (0.60 wt% Cu, 1.17 wt% Zn), and moderate Ag grades (27.83 g/t) at ca. 0.37 Mt ore. Gold and Ag occur as electrum and different Ag varieties including Ag-Hg ± Au alloys, miargyrite, and pyrargyrite that occur often in close proximity to electrum. Additionally, Ag-, As-, Sb-, and Sn-bearing sulfosalts are frequently observed and usually close to electrum. These textural relations strongly favor a syngenetic/magmatic origin for the 1806 zone, despite having a metamorphic overprint.

Jan 1, 2011

By S. Gregory

Many gold treatment plants have sulphides and coarse particle gangue components that contain gold in their tailings (cyanide leach residues and flotation tailings). Coarse and very fine liberated gold may also be present in some tailings streams. Two issues usually govern the economics of recovering additional gold from gold occluded in sulphide and gangue particles. The liberation characteristics of the gold in the sulphide and coarse gangue (gold liberation versus grind size) is the first and most important of the two. If fine grinding can liberate a reasonable amount of the gold, then the next important issue is how effectively these two constituents can be concentrated. Flotation will achieve high sulphide recovery but is usually costly. Selectivity is also an issue because of entrainment. Continuous centrifugal gravity concentration offers a viable solution to the recovery of both sulphides and coarse gangue however selectivity is also likely to be a problem. The possibility of improving concentrate grade by using a Falcon B separator was investigated. This paper describes a program of test work carried out on a gold leach tailings using a laboratory Falcon '13' separator. The program involved three different bowl angles: 10, 12 and 14 degrees and two bowl speeds (giving 250 and 350G accelerations). A number of tests were also performed on samples that had free gold present to ascertain the size-by-size recovery of gold in these samples.

Jan 1, 2005

By A. McLean, L. Gao, Z. Shi, Y. D. Yang, K. Chattopadhyay, G. F. Zhang

Levitation melting of metals is one of the emerging applications of magnetic and electric fields in liquid metal refining. The varying magnetic field generates induced current inside the metal droplet and leads to the Joule heating effect and Lorentz force against gravity. This contactless process can avoid contamination from the crucible and can be used to produce high-purity materials. Visualization of the levitation melting process is difficult, and thus generally investigated by mathematical modeling. In the present study, a three-dimensional mathematical model of metal levitation was developed using finite element method for proper understanding of the levitation process. The effects of harmonic magnetic field frequency, coils power input, and sample size on levitation nickel droplet were investigated. Temporal evolution of temperature fields were predicted directly though the model. Levitation and balance condition of the droplet were investigated as well.

Jan 1, 2015

By S. Khallouk, J. Zollinger, J. R. Kennedy, E. Bouzy, B. Rouat, D. Daloz

Titanium aluminides recently replaced Ni-based superalloys as turbine blades in the last LP stage of aircraft engines. To extend their range of use at higher temperature their properties need to be improved, either by alloying or processing. An efficient solution is to reduce the grain size during the solidification process. In the first part of the paper, an overview is given on the possibilities for grain refinement of such alloys, based on literature data and new results. The most efficient grain refinement is obtained with boron addition which leads to boride formations that are detrimental for in-use properties of turbine blades. In this work, the use of the high grain refinement potency of inoculation with non-brittle particles has been used by developing new refractory-based inoculants. The effect of one of these inoculants on grain refinement of an as-cast structure in a Ti-46Al is presented; resulting in a reduction of the grain size by a factor of 3.While less efficient compared to the potency of boron containing alloys, the grain refinement is effective and does not introduce any embrittling particles.

Jan 1, 2015

By H. W. Leon, F. J. Ellis

"This paper covers the new six-strand curved-mould billet casting machine at the Contrecoeur Works of SidbecDosco. It commenced production of 3 Yz-in. square billets at the beginning of January 1972. Together with two 100- ton ultra-high-power electric furnaces in a new meltshop, it is the principal source of billets for the existing rod and bar mill also located at Contrecoeur. The paper develops the reasoning for casting-to-size 3Y2 -in. billets and for choosing a six-strand machine. It indicates the significance of Sidbec-Dosco Montreal Works' extensive experience in operating a four-strand curvedmould billet machine since 1965 and the ways in which this experience influenced the design and operation of the new caster. Machine features are described in detail, as are the reasons for some of the features. The installation, checkout and crew training are briefly discussed as well as the tundish teeming trials. The first cast on January 5, 1972, is covered and a log is shown of the first casts to an empty ladle. There are operating statistics covering the first 100 casts, which produced 8000 tons of good billets in ten weeks of operation. Machine performance and billet quality were good and the few minor problems encountered are described."

Jan 1, 1973

By Julia Pflieger, Manfred Russ, Johannes Gediga

This paper shall show an economic feasible approach to implement Greenhouse Gas (GHG) reduction measures into the mining and metallurgy industry. The goal to improve energy consumption is directly linked to the reduction of GHG emissions and therefore directly in correlation with the economic viability. A baseline scenario of the considered reference system and of the respective reference year has to be defined, mapped and analysed. In a second step an analysis of the same operation using available and prospected Best Available Technology (BAT) processes is carried out to generate a basis for a benchmark system. The identified reduction potentials are reported and the GHG emission reductions are put into relation to the investment cost of the new process technologies / process adaption to be implemented. This economic feasibility calculation is necessary to realise a cost efficient GHG reduction roadmap implementation into the company's business operations. The GHG reduction roadmap is developed using ratios between GHG reduction and investment / operating cost to get an indication for a sequence for implementing carbon emission reductions measures.

Jan 1, 2010

By T. V. Nethery

Introduction A brief account of the East Malartic fire is essential if this paper is to serve the purpose implied by its title. The fire originated in the timbers of No. 4 shaft at the 10th, or 1,570-foot, level; this was the top or collar of the underground sinking operations. At the time, sinking was in progress and the shaft bottom was 242 feet below the 12th station horizon, or 618 feet 'below the l0th level. Above the l0th level, the shaft was not in use as the surface plant was not yet completed. The shaft crews descended from surface in No. 3 vertical shaft to the l0th level, where they transferred to No. 4 shaft, a distance of 1,450 feet. Of the sixteen shaftmen mucking at the shaft bottom, four were able to reach safety. One shaftman was overcome by fumes midway between the two shafts on the l0th level, while attempting his escape. The remaining eleven men climbed as far as the 11th station and there succumbed to carbon monoxide. No. 4 shaft, inclined at 61 degrees, bad been raised and timbered from the 10th level to surface; this bad been followed by sinking operations below the l0th. Two air hoists had been set up in the footwall of the shaft, 110 feet above the 10th level, and directly behind compartments No. 2 and No. 4. The waste from the shaft bottom was hoisted in 28-cubicfoot buckets on mono rails and dumped over standard shaft sinking doors into waste chutes built into No. 1 and No. 3 compartments. The five-compartment shaft, 7 ft. 8 in. by 34 ft. 6 in. overall size, was heavily timbered. In addition to the standard shaft timbers of 8 in. by 8 in. and 8 in. by 10 in. B.C. fir, the hanging-wall and ends of the shaft were laced with 4-inch spruce lagging. This represented approximately 300 board feet of timber in placee for every foot of shaft. The cause of the fire bas never been determined, despite every effort to do so. The inquest held for those who lost their lives in the fire was an extremely thorough one, but only the location of the origin, and not the cause, was established.

Jan 1, 1950

By C. J. Cajka

Commodity agreements, trade liberalization, producer cartels, the New International Economic Order, price stabilization and access to supply are buzz words of the day. The international concern and dialogue on these concepts, often by a new breed of politically motivated experts, have generated intense interest in seeking an international solution to natural resource problems. While this momentum was maintained during the past year, the growing incidence of protectionist actions by several major nations has been eroding confidence in the global approach. The seriousness of current difficulties has created an urgent need for decisive action. At the same time, the limitations of the global approach have become more evident.

Jan 1, 1978

By Zhou Yanwen, Fudong Wang, Shing Liu

Mixed CrB2 and MoS2 powder (Cr:Mo=1:1 atomic %), without any further process, were used as the targets to be sputtered and deposited onto stainless steel and silicon substrates by pulsed DC power supply. The structures and properties of the CrBMoS films were then analyzed by using SEM, XRD, micro-hardness tester. The SEM morphology of the films showed dense, defect free structure, and the preferred orientations of the films were CrB2 (111) and MoS2 (200) according to XRD spectra. The thicknesses of the films were measured and the relationship between the deposition rates and pulsed factors was determined. The films, with the micro-hardness as high as 19GPa and friction coefficient as low as 0.02, could be considered to be the hard solid lubricant films.

Jan 1, 2015

By W. Swidzinski

"Zelazny Most" post-flotation copper mine tailings pond is the only place to of storeing wastes for KGHM POLSKA MI EDZ S.A. The flotation tailings is are the main waste stream in copper mining in Poland. Sufficient storage capacity for tailings is crucial for , thus uninterrupted production of copper is crucially related to the possibility of storing wastes in the pond. The pond covers a Its over 14 km2 arca, almost 50 m high dams making this dame this construction one of the largest in the world. The risk assessment of potential damage due to un stable ility loss of dams or environmental contamination, as well as safely constructing damsincrease of dams within the design criteriaprocess, require quick access to a large amount of the monitoring data , which in vast amount have to be monitored, that needs to be analyzed and processed and reported, every day. This In the paper describes the numerical information system "SyZeM" , used for designated to the "Zelazny Most" pond, baseding on the Oracle database and Geographical Information System , to manage the graphical and descriptive data in coherent way., is presented. The main structure of the system, as well as the methodology of storing, processing and reporting the geological, geotechnical, hydrogeological, geophysical, chemical and survey data are shown. The aspects of Optimizing optimal and risk mitigation and safe management of copper wastes and risk mitigation with the help of "SyZeM" are discussed.

Jan 1, 2007

By F. E. Goodwin

Since the last CIM Zinc and Lead Conference ten years ago, significant technical and market forces have influenced how these metals are used, and the geographic distribution of their uses. Unprecedented price fluctuations have opened competitiveness issues, while the rapid growth of the Chinese market has created challenges both inside and outside China. Recent technical developments in battery energy storage, coatings, castings and chemical applications of lead and zinc will be reviewed together with the influence of these trends on end use markets.

Jan 1, 2008