Search Documents

By P. D. Hanson, H. Colijin

"New procedures and techniques are now available for the design of bulk storage bins. These new methods have essentially eliminated guesswork in the gravity flow of bulk solids, and have provided a sound basis for the quantitative analysis of alternate designs of hoppers and bins. This paper will discuss the practical application of the Solids Flow Theory (Jenike & Johanson) and illustrate the required design procedure with a few examples of actual bin operations."

Jan 1, 1970

By A. D. Walters

"IntroductionScreens are used in coal preparation plants for four basic functions, namely:I. Scalping off large size run-of-mine coal for initial size reduction;2. Sizing of coal treatment in different process streams;3. Removal of magnetite (dense medium) from clean coal and refuse;4. Dewatering.Canadian coal preparation plants use screens extensively in the above functions. Even plants where no beneficiation takes place, screening and crushing are carried out in the size reduction process.Description of Process UnitsThe type of screen used in coal preparation plants generally falls into the following categories:Fixed Screens and Grizzlies (for large coal)Often a simple rugged construction, either set horizontally above a bin or inclined with the coal flow.Fixed Sieves (for fine coal)They are used for dewatering and/ or size separation of slurried coal or discard. The sieve bend, the Vor-Siv, the Wilmot riffle and the cross flow screen fall into this category. The most commonly used in coal preparation plants is the sieve bend, Figure 1. Coal slurry is fed tangentially onto a fixed curve wedge wire screen deck. The solids are separated at a predetermined particle size, delivering a partially dewatered overproduct and a dilute underflow. The coal slurry is initially delivered to the sieve bend via a feed box. A series of baffles spreads the feed evenly across the width of the deck. The slurry drops from the last baffle, passes through the feed spout and is fed tangentially to the screen. It is important that the feed should contact the surface immediately at the front end of the sieve bend. It is possible to lose as much as 250Jo of screening area with a poorly fitted screen box.The full stream of coal slurry flowing over the sieve bend decreases in depth, in increments of approximately •;4 the slot width each time it passes a slot. Sieve bends make a size separation at 112 to 2h the slot width. This feature virtually eliminates blinding of the screen surface. Slot sizes are normally quoted in millimetres, available standard slot sizes are from 2 mm to 0.125 mm. The sieve bend is also widely used in coal preparation for preliminary dewatering."

Jan 1, 1989

By L. S. Almeida, U. A. Courbassier, C. T. Guimãaraes, M. N. Souza, V. L. Silva, H. P. Dias, G. A. Bicalho, B. S. Rocha, P. N. Rodrigues, A. Carnevale

During primary aluminum production the anode changing is a very important task. So improvements on it will be essential to avoid disturbance and have a better operational control. After anode changing a good current distribution will be guaranteed using a cavity cleaner and precise anode setting. Albras switching a manually anode setting to an automatic one solved the setting problems. In this paper it will be shown some pot line results and the improvements on workers ergonomic and safety conditions. The device was developed in a partnership between Albras and Pesto.

Jan 1, 2006

By M. R. Hudec, M. A. Nikolinakou, P. B. Flemings

"We model the shale response to the large deformations associated with salt bodies, and we identify the implications of the stress changes for hydrocarbon exploration. We employ both the static and evolutionary approach, and show that while the static one can model actual geologic geometries, only the evolutionary approach can provide a detailed description of the stress history of shales, which is essential for predicting stress, porosity, and pore pressure and, more generally, for understanding Earth processes related to salt-hydrocarbon systems.INTRODUCTIONDuring the last two decades, understanding the stress, material behavior, and pore pressure in shales around salt bodies has become increasingly important. The energy industry routinely drills near salt (Beltrão, Sombra, Lage, Fagundes Netto, & Henriques, 2009; Meyer, Zarra, Rains, Meltz, & Hall, 2005; Seymour, Rae, Peden, & Ormston, 1993), because a significant number of hydrocarbon reservoirs around the world are found in layers dipping away from salt diapirs.Salt is a viscous material that cannot sustain deviatoric stresses. Under differential loading it flows, changes shape, and eventually relaxes to an isostatic stress state (Urai & Spiers, 2007). Therefore, emplacement of a salt body and its viscous relaxation process may cause significant deformation of the surrounding sediments, perturb their state of stress and create local overpressures (Dusseault, Maury, Sanfilippo, & Santarelli, 2004; Seymour et al., 1993). As a result, drilling near salt is particularly challenging, and problems leading to additional expense or even abandonment are common (Bradley, 1978; Dusseault et al., 2004; Meyer et al., 2005; Seymour et al., 1993; Willson et al., 2003).Historically, salt and the evolution of its cross section to the present day geometry have been studied using kinematic restorations (Rowan & Ratliff, 2012). This approach aims to explain the present geologic section through a sequence of plausible past sections; however, it does not model the constitutive response of the wall rocks, hence it cannot provide any prediction on their state of stress. Similarly, largestrain numerical studies (Albertz & Beaumont, 2010; Chemia, Schmeling, & Koyi, 2009; Goteti, Ings, & Beaumont, 2012; Gradmann, Beaumont, & Albertz, 2009) have focused on the rheological evolution of salt systems without modeling the geomechanical response of the sediments."

Jan 1, 2015

By A. Ghirian

Once cemented paste backfill (CPB) is transferred and placed into a mine stope, various coupled mechanisms will take place in the CPB material or structure. It will be subjected to strong coupled thermal (T), hydraulic (H), mechanical (M), and chemical (C) processes. Field studies have shown that the in-situ properties and performance of CPB differ from those obtained in the laboratory. This is mainly due to effects of the aforementioned coupled THMC mechanisms or processes. For a reliable and cost-effective design of a CPB structure and barricade, it is crucial to have a proper understanding of the THMC behaviour and evolution of CPB. Also, it is important to consider the effect of coupled THMC factors (e.g., self-weight pressure, drained/undrained and thermal conditions, pore pressure) while curing the CPB specimens. For this purpose, a laboratory setup is developed to investigate the properties of CPB materials. The setup is capable of curing CPB specimens (10 cm in diameter and 20 cm in height) under controlled vertical pressure (curing under stress) and various coupled THMC conditions, while continuously monitoring the evolution of total stress, pore pressure, suction, temperature, water drainage, chemical composition of the pore water and vertical deformation. Once the required curing time is achieved, the specimen can be extracted and then subjected to experimental tests of interest, such as those that determine the Unconfined Compressive Strength (UCS), shear strength parameters, saturated hydraulic conductivity and thermal properties. In this paper, we describe the developed experimental setup and present some results of the THMC behaviour of CPB under various curing stresses and rates of backfilling. The obtained results show that the THMC properties of CPB are strongly coupled due to several mechanisms, such as self-weight pressure, heat of hydration and suction development as a result of self-desiccation. The findings can assist researchers and practitioners to better understand THMC behaviour and thus design more cost-effective CPB structures.

Aug 1, 2013

By M. J. Gagnon

The agglomeration of particulate materials is used in many mineral processes to enhance the settling of the fine particles, Depending upon many physical and chemical parameters, the aggregates demonstrate specific density-size distributions, In this study, a fractal model of the agglomeration process is introduced, Based on reliable experimental data and on physical calculation, the model presented helps to envisage the initial formation of the micro-flocs, and to interpret the subsequent interactions between the aggregates in terms of either coagulation or flocculation, Data from different sources, materials and different agglomeration processes are analysed and compared in the light of the proposed model.

Jan 1, 2005

By L. G. Bergh

The experience developing a supervisory control and information systems in a SX pilot plant is presented. The plant is located at the Process Control Laboratory, Santa Maria University, in Chile. In this work, the problem of controlling this process is discussed and related literature is briefly reviewed. Then, an innovative control scheme organized in three levels, local, hydrodynamic, and metallurgical supervisory controls is presented in an architecture including field controllers, PLC, and PC networks. Operating decisions in the metallurgical supervisory control are taken with incomplete information from on-stream analyzers. The control proposed is based on metal and acid concentration predictions of intermediate and exiting streams through the use of dynamic and static models and flow rates and input concentration measurements. Preliminary results are presented. The main objectives are to develop and test intelligent techniques in a hybrid system, and to study measurement and supervisory control problems. It is expected to produce reliable results that will contribute to improve the efficiency of this emerging and important process.

Jan 1, 2007

By R. MacRosty

The demand to increase production levels in smelting furnaces has driven the increase in the power levels. Consequently, greater cooling capacity of the furnace shell has been necessary, resulting in the widespread use of water-cooled elements to protect the refractory linings. Since water ingress into the furnace is an explosion hazard, monitoring and maintenance of the water-cooled elements is of key importance. Some of Hatch's recent research and development efforts have been focused on methods to provide an increased level of monitoring of water-cooled furnace elements; this paper focuses on two technologies developed for this purpose. The first involves the installation of a fibre optic temperature sensor in a water-cooled tapblock. The sensor is capable of providing high accuracy temperature measurements with a fine spatial resolution throughout the tapblock. Hatch has already developed a diagnostic system that uses multivariate statistical analysis to interpret the large quantities of data generated by the sensor. A second technology under development is concerned with enhancing the operating integrity and safety through detection of leaks in the water circuits. A successful leak detection strategy requires minimal maintenance and the ability to detect minute leaks. An instrument that meets these criteria has been investigated and is currently under development. This paper focuses on the technology and results from the test work that has been completed to date.

Jan 1, 2007

A series of field and laboratory evaluations were conducted in order to characterize the effects of a Mann+Hummel SMF-AR® diesel particulate filter (DPF) system on the aerosols and criteria gases emitted by diesel engines. This system, with a durable sintered metal filter media and available active regeneration via an on-board electrical heater, has been considered for retrofitting diesel engines used in light- and medium-duty underground mining applications. Two DPF systems were installed on a forklift and locomotive from the underground mining fleet of the Vale?s Creighton Mine and evaluated over a 1,500-hour trial. This evaluation was complemented with field and laboratory emissions tests. The field tests were performed on the vehicles while at the Creighton Mine surface shop. During those tests, the emissions were assessed for the engines operated at hydraulic stall, high idle, and low idle conditions. The laboratory tests were executed at the diesel engine emissions laboratory at the National Institute for Occupational Safety and Health (NIOSH), here the DPF removed from the forklift was further evaluated at four steady-state engine operating conditions as well as at transient conditions using a custom-designed duty cycle. Very similar methodologies were used during field and laboratory tests to measure concentrations of aerosols and criteria gases in the diesel exhaust, both upstream and downstream of the DPF system. The concentrations and size distributions of aerosols were measured using a fast mobility particle sizer spectrometer, in exhaust diluted by a partial flow dilution system. The concentrations of CO2, CO, NO, and NO2 were measured in the raw exhaust using a Fourier transform infra-red spectrometer. Both field and laboratory emissions tests showed that the evaluated DPF systems were very effective in reducing aerosol emissions from all tested engines, and for all test conditions. The systems were found to have minor effects on gaseous emissions from those engines. The findings from this study should help the mining industry to better understand the benefits and challenges of using DPF systems to control the exposure of underground miners to diesel aerosols.

Aug 1, 2013

By M. Knot

Fans delivered to the Russian Federation, and eventually to countries of the former U.S.S.R., for mine ventilation must meet the legislative requirements of local jurisdictions. This paper presents a discussion of these legislative requirements and presents examples of fan equipment designed to meet the requirements. The legislative obligations discussed include four (4) separate requirements, including: ?Technical design requirements ? The Federal Agency for Technical Regulation and Metrology is responsible to issue a GOST R certification declaring conformance to the requirements ?Operational requirements ? A ?License for Application? must be obtained prior to operation ?Explosion risk requirements ? If the area of operation includes potential for explosion a special certificate must be obtained ?Technical condition requirements ? Market segments within the mining industry require special conditions that must be satisfied Examples of fans designed specifically for use in the Russian Federation are also discussed and examples provided. Designs for fan volume flow control will be highlighted.

Aug 1, 2013

By H. Hao

This paper outlines the development of a 2-D axisymmetric mathematical model to predict the evolution of temperature during the Direct Chill (DC) casting of AZ31 magnesium billets. Model predictions of temperature have been compared to measurements made on an industrial DC casting machine at Timminco Ltd, in Haley, Ontario. These measurements have been used to fine-tune the thermal boundary conditions employed in the mathematical model, The model, which is based on the commercial finite-element code ABAQUS, has been developed as part of a strategic project aimed at improving the DC casting process for light metals through a reduction in casting related defects and increased productivity.

Jan 1, 2004

By M. J. Young, C. A. Aird

"The Gem molybdenum prospect is situated at the head-waters of Clear creek, between the Fraser river and Harrison lake, about 30 miles north of• Harrison Hot Springs, B.C. Clear creek follows a deeply eroded fault zone southwesterly through the center of the claim group. Elevations range from 2,000 feet in the creek bed up the steep slopes flanking the creek to a height of 5,500 feet. The property lies within an area underlain by schists and gneisses which strike from north to west in a broad fold plunging steeply to the northeast. This metamorphic complex has been invaded by numerous bodies of grano-diorite, much of which is gneissic. A granite plug, roughly 2,400 by 4,000 feet in size, has intruded this broad fold just west of Clear creek and encloses a circular breccia pipe 1,500 feet in diameter. In the breccia pipe, fragments of metamorphic rocks, granite and quartz monzonite porphyry are firmly cemented in a matrix of quartz monzonite porphyry. All the above rocks are cut by numerous fractures filled by vuggy quartz veins, many of which contain molybdenite. Attentien was first drawn to the area by a quartz vein, 18 inches in width, known as the Gem vein, which consists of several laminated bands of quartz and molybdenite. Since 1964, exploration efforts have been directed toward attempting to outline a large, low-grade type of molybdenum deposit."

Jan 1, 1969

By S. Lun Sin

In this study, the effect of silicon on the microstructure, mechanical properties and hot tearing susceptibility of permanent mould cast AZ91E magnesium alloy was investigated. Varying amounts of silicon (0.5, 1.0 and 1.5 wt.%) were added to AZ91E in the form of an Al-53 wt.% Si master alloy. The phase formation, grain size and solidification behavior of each alloy were characterized and related to their tensile properties and hot tearing susceptibility. The results showed that the addition of silicon resulted in the formation of Mg2Si particles. The presence of these particles led to an increase of the hardness, but was detrimental to the tensile strength and elongation of AZ91E. However, silicon significantly reduced the hot tearing susceptibility of AZ91E. This was attributed to the reduction of the grain size and the decreased freezing range of AZ91E, which contributed to improve the interdendritic feeding during the last stage of solidification.

Jan 1, 2011

By R. Erpelding

High Pressure Grinding Rolls (HPGR) are said to be a good option in new grinding circuits. Due to their low energy consumption compared to other grinding systems such as SAG milling, there is a strong incentive to check their behaviour for certain ore types. With rising energy prices the operation will become even more beneficial in future. As published in the past, the HPGR is claimed to increase the liberation of the valuable mineral component within an ore. An investigation at the research centre of Polysius was conducted to substantiate the liberation behaviour in finish grinding operations. A pilot scale HPGR test unit (POLYCOM MAGRO) with a roll diameter of 950 mm and processing capacity of 80 t/h was used. Grinding tests were completed with a screen and a two stage drying air separation process (SEPOL). Analysis included standard screen analysis, fractional XRF and modern MLA technology. A technique was developed to oppose the amount of produced slimes (resuming bad flotation) against the positive effect of producing high mass fraction at flotation-easy sizes. The paper shows how effective the use of a dry grinding separation could be in terms of production of mass of liberated metal.

Jan 1, 2012

By A. C. Bonnier

"INTRODUCTIONI have been asked to make available our method of determining the ""Live Inventory"" within a gravity type thickener. The ""Live Inventory"" being that tonnage compatible with the optimum underflow density that satisfies the process requirements.One prerequisite of the calculations is the proper determination of the final pumpable underflow density. A further requirement is that, prior to shutdown, the thickener has been operated properly, particularly that it has not been operated for storage capacity.Until recently I had few chances to check the method. However, I was most fortunate to have had a recent opportunity covering several months on a 300 ft diameter thickener at a plant in the U.S.A., wherein the method was tested and verified many times. The method proved accurate in that our calculated tonnage checked with the actual dried physical inventory of the drying facility.At the precise moment that the feed to the thickener was shut down, a per cent solid determination was made at the critical place and the tonnage in ""Live Inventory"" determined. Let us say that at the moment the thickener U' Flow solids was 20%. The thickener then was allowed to cperate until the U' Flow solids dropped below 20%, at which time the thickener was deemed to be relieved. Anything much less than 20% was not suitable to the subsequent centrifuge operation.Most large metallurgical thickeners have a configuration of three slopes at the thickener ""bed"". These slopes are dictated by the raking blades and are shown on the manufacturers' erection drawings. The first slope is from the outer periphery and generally takes up a distance of about 60% of the radius, the second slope generally taking up the remaining 40%. Within this 40% area, there is usually another slope taken up by the cone on ""B"" type thickeners or an actual steeper inner slope on ""C"" type thickeners."

Jan 1, 1989

By Madaah Hosseini H. R., P. Abachi, S. Miraghaei

In this study, the effects of milling time, chemical composition and heat treatment on microstructure and magnetic properties of nanocrystalline Fe-Si (6.5-25 at.% Si) alloys prepared by mechanical alloying have been investigated. The results show that increasing the milling time or the Si content, decreases the lattice parameter and increases the internal microstrain. The prepared powders mainly consist of micron-sized particles with an average grain size of less than 20 nm. The specific saturation magnetization values are slightly less than those of single crystal or conventional Fe-Si alloys and decrease as Si content increases. The coercive force values of the nanocrystalline as-milled powders are much higher than those of corresponding Fe-Si bulk alloys with a minimum at 13.5 at.% Si. The values of coercive force decreased after annealing but it seams that the residual strain developed during milling is not the major contributing factor to the higher values of coercive force in the mechanically alloyed powders and nanocrystals behave as single-domain particles without exchange interaction between them.

Jan 1, 2006

By M. Kawahara, H. Sunayama

Oxidation rates of the cubic specimens, which were prepared by cutting the shaped magnesia-carbon bricks, were measured continuously with a thermo balance in the temperature range from 1273 to 1 823 K in N2-02 and Ar-02 mixed gas with 2.1 x 104 and 3.7x 102 Pa of oxygen partial pressure respectively. The effect of the graphite content, the maximum grain size of magnesia clinker and the oxygen concentration in the atmospheric gas on the oxidation rate for the MgO-C refractory has been investigated. The value of effective diffusion coefficient of O2, which diffuses through the porous decarburized layer, decreased with the decreasing of the porosity and the oxygen concentration in the external gas phase. It was speculated that the dense layer formed easily due to the high tortuosity of pores and the low recession speed of the carbon interface in the MgO-C bricks.

Jan 1, 2004

By H. S. Fowler

The Consolidated Mining and Smelting Company has been in the business of mining and exploration since its incorporation in 1906. The Company has reports written as early as 1890. Consequently, its files contain a very large number of reports, and also of maps, of ail descriptions. REPORTS Before describing the filing of maps, a brie{ note on our general system of filing reports will perhaps clarify the discussion. Reports of a non-periodic nature, primarily those based upon examinations by field engineers, are separated from all other data and filed in what we know as the Mine Series System. Each property on which reports are written is given a serial number, known as the Mine Series Number. This serial number is assigned at the time the first report is filed and it remains permanently identified with the property, regardless of its state of activity. Our mine series numbers now total over 5,000. The serial number for a property may be found by referring to an alphabetical index of properties. MAPS We found it necessary to divide maps into two groups: (1) Maps of properties (2) Maps of areas

Jan 1, 1944

By D. Seo, P. Au, X. Husang, D. Nagy

The production of single crystal (SX) turbine blades represents the current stateof- the-art in Ni-based superalloy design. With complex casting processes and alloy composition modifications, SX superalloys exhibit superior high temperature mechanical properties to their polycrystalline counterparts. Stresses and plastic deformation can occur in SX nickel-base superalloy engine components at various stages during their manufacture and use. For examples, stresses are created during initial solidification and also during solid state processing such as shot peening, grit blasting, blending, electrodischarge machining and welding. Stresses may also be created during service due to random events such as foreign object impacts. Subsequent exposure of SX to high temperatures during solution heat treatment and brazing repair can result in recrystallization which has been shown to be detrimental to both creep rupture strength and fatigue performance of the components. It is therefore the objective of this paper to understand the recrystallization behavior of two SX superalloys, PWA 1484 and 1483, subjected to pre-stressing and subsequent heat treatments.

Jan 1, 2006

By L. St-Georges

In aerospace and transportation industries, severe problems are related to fatigue failure. Aluminium is frequently used in these industries to optimize the solidity and minimise the weight of the structures. Nevertheless, the fatigue life of aluminium alloys is limited and specific efforts have to be made to reduce the vibratory stresses in the mechanical parts. When riveted, the life of the sheet metal structures can be increased compared to welded structures, due to the energy dissipated by the friction between the rivets and the sheet metal and the sheets themselves. In the past decade, a new tool was developed to assemble aluminium structures; the friction stir welding. With this new technique, fatigue life of the aluminium welded joints can be increased by a factor from two to ten. However, less energy can be damped by the friction between the components and increased vibratory stresses may occur. In this investigation, the potential of the friction stir welding to create damped aluminium sheet metal structures is evaluated.

Jan 1, 2006