Search Documents

By M. Carvalho

The primary motivation underlying the proposal of polygeneration systems for mine sites is to increase the efficient use of natural resources by combining different technologies and energy resources while satisfying energy service demands. For many mineral producers, particularly in Canada?s mining extremes of climate and depth, energy in support of mineral production can be the second largest cost centre after labour. A generic methodology is proposed for the design of energy supply systems in mine sites, based on a search for the minimum discounted cost of energy supplied for all feasible different plant configurations. These configurations can be represented within a connectivity matrix which corresponds to a network representation. A Mixed Integer Programming formulation is set out for the multiperiod synthesis and operational planning problem. This is characterized by i) binary variables for the selection of technologies, ii) integer variables for the determination of the number of units installed, and iii) by continuous variables for the representation of energy and economic flows. Through the integration of particular energy supply strategies matching specific mine circumstances (on-grid, remote, degree days, etc) and consideration of technologies that improve energy efficiency, hitherto not considered new technologies and demand management systems or new perspectives on optimal mine site energy supply can be investigated. Some of these investigations identify the economic conditions through which biomass energy feedstocks should be used, for direct heat production, for gasification and providing for Fischer-Tropsch syndiesel manufacture. As well as integrating demand from mobile diesel-fuelled plant into an optimization procedure that hitherto has only been considered for static energy production and consumption plant, this analysis shows how the techniques can be used to explore economic conditions of threshold prices for biomass (purpose-grown biomass and peat are considered herein) and trucked-in diesel. The methodology also allows for electricity and syngas storage and diesel and biomass bunkering. Within the paper the energy demands for a remote, open pit mining operation located in Northern Ontario are considered as a case study to illustrate the technique and investigations. As expected, for mines close to electricity, natural gas, and diesel distribution infrastructures, the optimal choice is to connect. When a constraint is applied specifying that connection is not possible, as would be for the case exemplified, the optimal choice includes some of the more exotic options for mine site energy supply.

Aug 1, 2013

By K. Purazrang, P. Sh. Naseri, P. Abachi

In present work, the comparative measurement of aluminum alloys' resistance to the unstable fracture was provided. Besides, the rupture mechanisms of high strength 7075 and 7050 aluminum alloys were investigated. The specimens were used as solution treated, quenched and aged condition. The elastic-plastic behavior of specimens was determined by carrying out tensile test on cylindrical specimens. The small sized specimen with 6.35 mm thickness and V-notched radius less than 60 µm was used for evaluation of damage properties, in accordance with ASTM B871-96 standard test method. All tear specimens were machined in L-T orientation. The mechanical tests were conducted at RT on an universal Instron machine under cross head speed of 0.1 mm/min. The results of mechanical tests made the evaluation of tear strength to 0.2 % tensile yield strength ratio, as a measure of notch toughness, available. The comparison of specimens' resistance to crack propagation and unstable fracture due to the presence of crack-like strain concentrator was provided using tear test data. The microstructure of specimens was studied under optical microscopy. The rupture micro-mechanisms were analyzed by examination of specimens fracture surfaces using SEM. The microstructure examination indicated almost equiaxed grains on the transverse directions and elongated grains on rolling direction. Moreover, intermetallic particles were evident at microstructure. Considering the SEM fractographs, it seems that the intermetallic particles act as void nucleation and damage initiation sites. However, the damage mechanism of tensile specimens and severely notched specimens, especially near the notched root differs due to stress and strain states.

Jan 1, 2006

By Ashu Garg, Anirban Bhattacharya

"Friction stir spot welding of aluminum alloy AA6061-T6 sheets was performed with circular (plunge depths 0.4 and 0.6 mm), square and triangular tool pin (plunge depth 0.4 mm) with constant 0.2 mm shoulder penetration to characterize various zones of weld nugget. It was observed that the depth of the stir zone formed below the tool pin is comparatively similar for different tool pins but wider for circular tool pin. The size of another stir zone formed at the interface of tool pin and a tool shoulder is observed to be larger for triangular and square tool pin due to the higher swept rate. Predicted strain from finite element analysis, calculated strain rate using Zener-Hollomon relationship and experimentally measured grain size distribution indicates severe amount of plastic deformation in-and-around the nugget/spot region. Finer grains in various stir zones were observed than thermo-mechanically and heat affected zones. Grain size (at distribution peaks) in stir zones varied around 2.54 µm to 3.69 µm for different tool pin profiles as compared to base metal grain size of 20 µm. Microhardness results indicate that the welded region is quite softened than base metal and maximum hardness is mostly observed around the thermo-mechanically affected zone.INTRODUCTION Friction stir spot welding (FSSW) is widely used for joining the sheets of materials like aluminum, copper, magnesium, etc. The process begins by plunging a rotating tool (generally having a pin and a shoulder) into the sheets to be welded. Continuous stirring of the tool and downward plunging force generates localized heat due to friction at the tool-sheet interface and plastic deformation of the sheet metal. The material gets softened and the plasticized material adjacent to the tool pin starts flowing due to the action of tool rotation and tool plunge thereby causing intermixing and bonding between the overlapped sheets. The tool stirring also promotes grain refinement in the weld nugget associated with high strain, strain rate and thermal cycle. The formation of new microstructure also affects the mechanical properties and efficiency of FSSW joints. Studies also showed that the tool pin design and tool shoulder feature exerts a noteworthy influence on the material flow and intermixing during the FSSW process (Reilly et al., 2015; Hirasawa et al., 2010). Sarkar et al. (2016) studied the material flow and intermixing during FSSW using tracer material method and reported that the size and width of flow zone increases with tool penetration depth. The influence of tool rotational speed on microstructure and stir zone temperature was investigated during FSSW of dissimilar AA6061-AA5754 alloys (Gerlich et al., 2007). They reported that the average grain size in stir zone of AA6061 weld increases with increase in tool rotational speed. In another work, Gerlich et al. (2008) studied the local melting and tool slippage during FSSW of Al alloys. Tool slippage was investigated by calculating the strain rate using Zener-Hollomon relation. Garg and Bhattacharya (2017a) studied the effect of dwell time, tool pin profiles and tool rotational speed on shear strength, microstructure, temperature and strain distribution during FSSW of AA6061. In another work, Garg and Bhattacharya (2017b) analyzed the effect of different tool pins and pinless tools on the shear strength and microstructure during similar and dissimilar FSSW of AA6061-T6 and pure Cu. Chang et al. (2004) proposed mathematical relationship between the average grain size and Zener-Hollomon parameter during friction stir processing of Mg alloy. Solhjoo (2010) presented a mathematical approach to determine the critical strain as a function of peak strain required for initiation of dynamic recrystallization in austenitic stainless steel. Fratini and Buffa (2005) also proposed the numerical model to determine the grain size during continuous dynamic recrystallization phenomenon."

Jan 1, 2018

By Joseph Bradley

THROUGHOUT this article, minerals used in the paint industry are designated 'pigments'. They may be classified in two groups: (1) Pigments which are used in the state in which they occur in nature, requiring only mechanical preparation. (2) Pigments which require heating or chemical treatment before use, in order to obtain from them a product of the desired quality or shade of colour. They may be further classified according to colour, as follows: White Pigments .-These include calcium carbonate (chalk, marble), gypsum and alabaster, kaolin-or china-clay, and magnesia. However, the white pigments most extensively used are compounds prepared chemically from minerals containing lead, zinc, titanium, and antimony. The white pigments are of particular importance because, not only are they used by themselves, but they also serve as adjuncts to other colours for the production of special shades. Yellow Pigments.-These are mainly naturally occurring ferric hydroxides, as limonite and bog iron ore, or similar. compounds prepared artificially. Brown Pigments .-Pigments of this group are distinguished for their beauty and depth of colour, and many of them are used in the finest of paintings. Familiar names are sienna, umber, and Vandyke brown. They are for the most part ferric hydroxides, containing varying amounts of water; but the group also includes a manganese brown, which consists chiefly of a mixture of oxide and hydroxide of manganese. Red Pigments.-Chief among this group is ferric oxide, known under various trade-names, such as Canadian red, Persian red, etc., and also the much prized and somewhat rare vermilion. The pigment used is either naturally occurring hematite, de-hydrated limonite, or artificially produced red ferric oxide.

Jan 1, 1937

By R. L. Bruening, L. Navarro, R. M. Izatt, N. E. Izatt, S. R. Izatt

Green chemistry principles will be discussed, and examples will be given of the use of Molecular Recognition Technology (MRT) to selectively separate valuable metals such as rhenium and palladium from various copper refinery feed streams. Recovery of these metals has numerous advantages including (i) conservation of valuable resources, (ii) prevention of environmental damage, and (iii) elimination of capital and operating expenses due to re-processing or disposal of metal-bearing streams. INTRODUCTION Refining of copper ores has a long and successful story. The history of copper, one of the first metals mined in human history, illustrates the global challenges faced as a result of increased demand for major metals and for by-product specialty metals found with them in trace amounts (Izatt et al., 2014). Copper has valuable properties, which have sustained its use over the centuries. It is an ideal material for creation of novel materials. Some desirable properties of copper that have proved valuable in our high-technology society include suitability for alloying with many other metals; ease of joining by soldering and brazing; good combination of mechanical qualities; high resistance to corrosion; suitability for many artistic purposes; and, of great importance in the modern era, efficient and economic use as a conductor of electricity. Copper mining in the U.S.A. began in the late nineteenth century in Montana (Izatt et al., 2014). The estimated total amount of copper mined globally before 1800 is about 5 million tons, four times less than is mined in a single year today (Flanagan, 2018). Production of copper in the U.S.A. has remained fairly constant at about 1,300,000 to 1,400,000 metric tons per annum from 2013 to 2017. Specialty metals such as bismuth, rhenium, molybdenum, and others that have become essential in our 21st century technology, and precious metals such as silver, gold, and the platinum group metals (PGMs) are concentrated by geochemical processes in trace amounts in copper ores. These specialty and precious metals were discarded into tailings in early mining operations, since limited extractive technologies existed and uses for most of them were limited. Thus, economic benefits for recovering them were limited, primarily, to silver and gold. Today, copper processing is the main, and often the only, commercial source for certain of these elements (Izatt et al., 2014). For example, molybdenite (MoS2) is the predominant ore mineral of molybdenum mining (Pohl, 2011). Cu-Mo-Au porphyry ore deposits supply ~75% of the world’s copper, 50% of the molybdenum, nearly all of the rhenium, and 20% of the gold. Typical ore grades are 0.5–1.5% copper, 0.01–0.04% molybdenum, and <1.5 g/ton gold. Molybdenite is the primary source for rhenium, among the rarest of metals, which is an essential component of super alloys, such as turbine blades in the aerospace industry (Pohl, 2011). Most rhenium is obtained as a by-product of molybdenite from copper mines in Chile. The case of rhenium raises an important issue. Continued availability of rhenium, selectively concentrated in copper ores, depends on continued mining and processing of copper. Since the mining company’s main interest is typically in copper production, continued recovery of rhenium and other specialty elements present in the ore body is at risk. Dependence of specialty metal supply on continued mining of major metals exists in several additional cases including indium, gallium, selenium, tellurium, germanium and bismuth (Pohl, 2011). PGMs, on the other hand, are typically mined for their own value, which far exceeds that of associated base metals. However, copper ores often contain marketable amounts of platinum and palladium, making their separation of interest, if this can be done economically.

Jan 1, 2019

By Qiling Zhang, Zengqian Hou, Xiaoming Qu

Abstract - The Okinawa trough is an active back-arc-spreading center in which submarine hydrothermal exhalation (black chimneys) and sulfide mineralization are forming. Fluid inclusion composition in minerals of the hydrothermal feeder zones in the JADE field shows that the hydrothermal systems are extremely gas-rich. There are two independent and co-existing fluids, CO2-hydrocarbon and saline fluids. Microthermometry and Laser Raman Microprobe (LRM) analyses on individual fluid inclusions of the CO2-hydrocarbon type, dominated by CO2 and containing minor CH4, C2H4, C2H6, N2 and H2S, are almost equivalent to the fluid inclusion composition of a natural gas field. The saline fluid is mainly composed of H2O and contains minor Na+ and K+. It is close to a H2O-NaCl, or H2O-NaCl-KCl system, with salinities from 3.7% to 7.5% NaCl eq. Before venting on the seafloor, the fluids experienced immiscible separation. One of the end-member fluids is downward circulating seawater that interacted with sub-seafloor rocks. The other was gas (volatile)-rich fluid derived from a shallow magma chamber. The immiscibility separation of fluids resulted from the decrease of temperature and pressure of the hydrothermal system and continuous input of magmatic volatiles. The saline fluids in this system are discharging to form sulfide chimneys and black smoke. Meanwhile, CO2-rich fluid discharges as CO2 bubbles through hydrate pipes. A large amount of CO2-CH4-H2S gas or fluid in the upper part of the hydrothermal system, and reaction of this gas or fluid with saline fluids, finally enables the accumulation of metal sulfides.

Jan 1, 1999

By J. R. Kish, J. Dabrowski

"The susceptibility to intergranular corrosion modes is a major technical issue preventing widespread utilization of higher strength welded AA7xxx extruded beam profiles, in the peak-aged T6 condition, in automotive bumper assemblies. A study was undertaken to evaluate the relative exfoliation corrosion resistance (ASTM G85-A2) as a function of joint design parameters, namely the base alloy composition, heat-treated condition and beam orientation after exposure to a cyclic acidified salt spray test. This paper documents the major findings extracted from this study.INTRODUCTIONBumper systems play a predominant role in the passive safety of an automobile, since they are one of the main structures for absorbing the collision energy in the event of an automobile crash. Heattreatable AA6xxx-series (Al-Mg-Si) and AA7xxx-series (Al-Zn-Mg) Al alloys, with relatively high strength, toughness, energy absorption, weldability and formability, make it possible to design costcompetitive bumper systems to crush in a controlled fashion. In this context, Cu-lean AA7xxx extrusions, such as AA7003 and AA7108, which exhibit higher strength than AA6xxx extrusion, such as AA6082, represent an attractive light weight material from which to fabricate bumper assemblies (Clausen et al., 2000; Pedersen et al., 2008; Chen et al., 2009).Arc welding is a key joining process for AA7xxx alloys within the transportation industry. A major technological issue preventing widespread utilization of arc-welded AA7xxx joints is the susceptibility to severe localized corrosion (Kent, 1970, Reboul et al., 1985; Holroyd et al., 1987). It generally occurs as exfoliation corrosion within a heat affected zone (HAZ) a few millimeters from the weld bead, or a type of stress corrosion cracking (weld-toe cracking), which initiates at the weld toe and propagates into the interfacial region between the weld bead and the HAZ (so called “white zone”). In addition to the micro-galvanic cell activity induced by the intermetallic compound constituent and strengthening particles present, there is strong evidence that macro-galvanic cell activity between the weld bead and base AA7xxx alloy may be playing a controlling role. Electrochemical profiles taken across fusion welded joints, in cross-section, during exposure to saline solutions suggest that a significant potential difference exists across the AA7xxx arc-welded joint (Shumaker et al., 1967; Grauer and Wiedmer, 1980; Tuck, 1985, Onoro and Ranninger, 1993). These studies consistently show that the HAZ and base alloy are more electronegative with respect to the weld bead (arc-welded with AA5xxx filler wire). Despite this initial important work, the majority of the recent corrosion research effort on welded AA7xxx alloys has focused on the performance of friction stir welds (Lumsden et al., 1999; Wadeson et al., 2006; Hatamleh et al., 2009)."

Jan 1, 2012

By William D. Gallant, Thomas M. Barczak, Carol Tasillo

"This paper describes the results of full-scale testing of several multi-layered wood crib configurations that were tested in the Bureau of Mines mine roof simulator in cooperation with the Cape Breton Coal Research Laboratory and Cape Breton Development Corporation of Sydney, Nova Scotia. Nine different crib configurations currently being used as wood packwall supports for advancing longwall applications in Canada were evaluated. Configuration parameters understudy included the aspect ratio (height-to-width relationship) and percentage of solid material used in the crib construction. Test results and generalized wood crib behaviour are discussed in detail. Recommendations are made concerning crib constructions to maximize strength and stability. A cost benefit analysis of multi-layered wood crib configurations is made. A comparison of laboratory results and underground observations of several wood packwall supports in the Sydney coalfield suggest in situ load capacity is less than that measured in laboratory testing. Reasons for the apparent decrease of in situ load bearing capability are described.IntroductionA cooperative effort was undertaken by the U.S. Bureau of Mines with the Cape Breton Development Corporation (CBDC) and the Cape Breton Coal Research Laboratory (CBCRL) to evaluate the behaviour of gateside packing materials used in advancing longwall mining applications in the Sydney coalfield. As part of this effort, full-scale tests were conducted on wood packwall supports in the Bureau&apos;s 3-million pound (13.3 MN) active load frame.Nine different pack configurations were evaluated as part of this study. The wood packwall supports were multi-layered crib constructions from 6 in. (0.15 m) by 6 in. (0.15 m) cross section timbers using timber s 30 in. (0.75 m) and 60 in. (1.5 m) in length . The percentage of solid material in the crib constructions varied as illustrated in Figures 1 and 2. A summary of crib constructions is provided in Table 1."

Jan 1, 1991

By I. Farr, H. Wittens

"In 1989 and 1990 abnormally high levels of arsenic in ore from the Thompson Open Pit Mine threatened Manitoba Division's electro-nickel production. The paper will discuss our development of a flotation process to separate pentlandite and gersdorffite (the prime nickel and arsenic bearing minerals).The presentation will focus on the development of the process from conception, through lab and plant test work, to plant optimization and full scale production. The paper will conclude with the benefits and cost of the completed project.INTRODUCTIONRejection of arsenic from nickel sulphide ores was not a primary concern in the Manitoba Division until 1989. At that time increased production in the Thompson Open Pit mine, which contains high arsenic ore zones, resulted in excess amounts of arsenic in the Thompson Refinery affecting electro-nickel quality. This problem was resolved through extensive efforts by Mill personnel. The purpose of this paper is to familiarize the reader with- the Thompson Mill.- the mineralogy of the Thompson orebody.- the evolution of Ni/As separation in the Mill.- the metallurgical impacts of the separation on the Mill.- the importance of the separation to the Manitoba Division."

Jan 1, 1991

By Chr. Krause

Within the scope the collaborative research centre 599 (Medical University of Hanover, University of Veterinary Medicine Hanover, University of Hanover) the behaviour of the degradation of magnesium materials as implants are investigated by using animal experiments (rabbits). Thus extruded cylindrical pins from the magnesium alloys MgCa0.8%, WE43 and LAE 442 were implanted intramedullary in the tibiadiaphyses. The implantation duration was 3 and 6 month. After the explantation 3 point bending tests were carried out to investigate the possible changes of the mechanical properties. Clearly changes in dependence of the implantation duration could be determined. The three magnesium alloys show a decrease of the mechanical resistance with an increasing implantation time. To evaluate the degradation process, wich is the reason for the changes, micrographs and element analyses (EDX) have been accomplished after the 3 point bending tests. The micrographs show for all used magnesium alloys corroded surfaces but no preferred corrosion on the grain boundarys. The element analyses show beside a layer which is rich in calcium and phosphorus an agglomeration of rare earth elements in this layer. With these results a using of magnesium alloys as a material for implants can be announced.

Jan 1, 2006

By D. Gaboury

Most hydrothermal gold deposits contain quartz with fluid inclusions that record composition and temperature of the mineralizing event. Quartz has strong chemical and mechanical resistances to weathering and abrasion. Hence, quartz fragments occurring on weathered surfaces or in till cover have the potential to be used for gold exploration as far as we know what is the signification of the volatile content of the fluid inclusions for gold mineralization. In this perspective, fluid inclusions were analyzed in pure quartz by solid-probe mass spectrometry from gold deposits hosted in the Archean Abitibi (Canada) and Paleoproterozoic Birimian (Western Africa) belts. This approach provides the relative abundance of volatiles from families of fluid inclusions decrepitating at specific temperatures (Td). Fluids in gold deposits are aqueous-dominated with CO2 and minor H2S in accordance with their fundamental role as gold-ligands (H2S) and for pH-buffering (CO2) of the gold-bisulfide solubility. However, there is no correlation between CO2 and H2S contents of fluid inclusions with the gold grade of the samples. This suggests that trapped fluids represent a marginal portion of the fluid history recorded by the veins. However, in barren quartz veins away from known mineralization CO2 or H2S are commonly absent. Wide ranges in H2O Td from 250 to 450°C and CO2-H2O Td offsets are common, indicating phase separation. The content of other volatiles seems to be more dependent on the geological setting. Helium content may suggest proximity to a crustal-rooted fault, a critical parameter for gold mineralization. Methane and especially C2H6 appear to be indicative of fluid buffering by organic-rich material such as graphitic-shale. These rocks may provide an important primary gold reservoir from sedimentary metal-rich pyrite. Nitrogen-bearing fluids may be related to a magmatic component but can also be derived from organic-rich sedimentary rocks. For gold exploration, quartz containing CO2- H2S-bearing fluid inclusions and having H2O-CO2-Td offsets within 250 - 450°C has strong vectoring potential.

Jan 1, 2011

By George S. Martin, Michael D. Winship

"Placer Dome Inc. is the operator of the Musselwhite project located 100km north of Pickle Lake, Ontario. J.S. Redpath Limited was contracted to conduct an underground exploration program using shaft access.During the winter of1988, the shaft collar was established in 16 metres of water bearing sand and till overburden. This paper will illustrates the engineering techniques used to overcome the obstacles to installing a shaft collar in deep overburden. Specialized dewatering and piling procedures were employed.INTRODUCTIONHarold and Allan Musselwhite discovered gold in the Opapimiskan Lake area, north of Pickle Lake, in 1962. The prospectors were grubstaked by ten companies in 1973.A diamond drill program was initiated shortly thereafter.In 1983an underground ramp exploration program was carried out on the West Anticline portion of the property. The program was unsuccessful in establishing an ore reserve so surface exploration continued. In 1986the ""T"" zone was discovered. Further surface drilling was done and an over-all drill-indicated reserve of 6 million tonnes at 7 grams per tonne was outlined. The gold mineralization occurs in several vertical tabular deposits within the iron formation. In late 1987the joint venture partnership, now consisting of Placer Dome Inc., Inco Gold Co., Corona Corporation and Esso Minerals Canada, contracted J.S. Redpath Limited to conduct an underground exploration program on the ""T"" Zone.The scope of work for the project was to: 1. establish a 45 km winter road in 1988 and 1989;"

Jan 1, 1989

By E. H. Mulligan

THE ERRINGTON B-I mine is located on the Errington orebody of Steep Rock Iron Mines, Limited, at Steep Rock Lake, Ontario. In 1946, this orebody entered the shipping lists of the Lake Superior iron ranges as an open-pit operation. During the period 1946 through 1953, the mine produced a total of 9,000,000 tons of iron ?ore. In 1950, as the mine approached the economic limits for open-pit operations, ground was broken for an underground development to exploit the deposit at depth. The mine is designed for an ultimate production of 1,500,000 tons per year by the block-caving system of mining. The initial shaft is 1,200 feet deep and will produce or-e from the 700 and the 900 levels. The 1,100 level will be used as a drainage level and as a haulageway for waste rock, which is hoisted to surface by skip. Ore from the two production levels moves by a system of ?ore passes to a crushing plant located below the 900 horizon and is hoisted from this point to surface by conveyor belt. At the present time, all material handling on the levels is by tramming, but as tram distances increase conveyor haulage will probably be installed. The initial stage of the Errington B-1 development is expected to produce 6,000,000 tons of ore over a period of four years. The second stage will require deepening of the shaft and development of lowe1? production levels. The conveyor hoisting plant will be extended to serve these new levels. We visualize the mining of this orebcdy down to 2,500 feet by these methods.

Jan 1, 1956

By P. J. Mackey

"The metal producing industries in Canada and in the U.S. in many ways owe their technical beginnings to Welsh technology. The first copper smelter in Canada started in 1849-50 with a Welsh reverberatory furnace and skilled furnacemen brought across from Swansea to operate the equipment1- The Rocky Mountain smelting industry began with the installation of furnaces resembling the Swansea smelters(2). It was only later that the North American industry developed newer and improved methods. This article briefly describes the metallurgical history of the Lower Swansea Valley, being that section of land stretching northward from Swansea along the banks of the River Tawe, and bordered by hillsides east and west of the river. The Valley has had a classic cycle of development and decline common to industrial areas of Britain which grew in the Industrial Revolution. Perhaps more than any other area today, the Swansea Valley represents a complete cycle of use from agricultural to the peak of industrial development through to decline and dereliction. The conditions which made the Tawe Valley attractive to certain industries were laid down nearly 300 million years ago with the Carboniferous swamps and forests which covered the area, later forming the south Wales coalfield. As a result of glacial action and the deposit of glacial outwater and alluvial gravels, the valley adopted the traditional configuration, with its rocky sides occasionally remaining exposed. Up to probably about the 16th century, the Lower Swansea Valley was similar in use and appearance to many other valleys in the region. From the 14th century, the natural oak woodland had provided a continuous source of timber to produce charcoal for iron making as well as for structural purposes. Agriculture was the main activity in the valley in this period, but it was likely that the farmers also mined small amounts of coal by way of ""bell pits"", and adits into the coal seams."

Jan 1, 1999

By I. Ciabatti

Inorganic salts of hexavalent iron (ferrate (VI)) are versatile reagents for water and industrial effluent treatment because of the strong oxidising effect of the ferrate ion (FeO42-) and the well-known coagulation properties of the resulting ferric ion. Among other applications, ferrate can effectively remove arsenic, cyanide and phenols from industrial effluents. Furthermore, ferrate salts can be prepared from ferrous sulphate, a common byproduct of the steel and titanium industries, and possibly from other iron wastes. Notwithstanding their many potential advantages, the industrial-scale application of ferrate salts, such as potassium ferrate (K2FeO4), for effluent treatment has been hindered by the difficulties inherent in their synthesis and stabilisation. Within a project co-funded by the European Commission, the large-scale synthesis of stabilised potassium ferrate was realised through a new synthesis process, and different applications of the resulting ferrate to effluent and wastewater treatment are under investigation. This paper reports the results of the application of stabilised potassium ferrate for the purification of textile effluents. Laboratory and pilot-scale tests were carried out and the performance of the ferrate was compared to that of chemicals currently used in wastewater treatment. According to these experiments, potassium ferrate is a promising reagent for an effective treatment of textile and other industrial effluents.

Jan 1, 2006

By I. B. Schalamuk, R. E. de Barrio, M. J. Pons, M. B. Franchini, L. Meinert

"Several Fe, Fe-Cu, and Cu-Ag prospects hosted by Mesozoic carbonate-rich sedimentary rocks that were intruded by diorite stocks define an approximately 20 × 200 km belt along the Andes Cordillera of southwest Mendoza province, Argentina (34°-36°S). This belt includes the Hierro Indio and Vegas Peladas Fe skarns, Las Choicas, and several other Cu-(Ag) prospects.The main features of the Fe skarns include: association with mantle-derived middle Miocene (~15-11 Ma) diorite stocks and sills; widespread alteration including epidote ± amphibole ± magnetite endoskarns, and zoned garnet (Grs0-66 Adr32.5-100) ± magnetite ± pyroxene (Di24-50 Jo2-9 Hd74-41) exoskarns formed from oxidized, saline, high-temperature brines (530º-660ºC; 60-70 wt.% NaCl equiv.); and magnetite-hematite orebodies associated with quartz ± epidote ± calcite ± actinolite formed at lower temperatures (290º-436ºC) from saline fluids (32-50 wt.% NaCl equiv.) of magmatic origin.West of the Fe skarn belt, the Valle Hermoso district covers more than 300 km2 and hosts several poorly known Cu-(Ag) prospects (estimated 30 Mt with 1.5% Cu and 20 g/t Ag). These prospects share many characteristics with the iron oxide copper-gold-type systems and manto-type Cu deposits of northern and central Chile. One of the prospects (Las Choicas) is located at the apex of a regional 015°-trending anticline, along the contact of stratified calcareous sandstone and limestone (Neocallovian-Oxfordian) with a diorite pluton. This pluton has positive Ta and Nb anomalies (on normalized diagrams) and a high Ti content, features uncommon in Miocene diorites associated with Fe skarns and of magmas derived from sub-arc mantle sources. Alteration at Las Choicas includes early widespread chlorite + calcite ± albite ± scapolite ± ilmenite or titanite ± apatite, and local actinolite ± hematite ± biotite alteration of diorite and sedimentary rocks along contacts. Later Cu mineralization (1%-10% Cu) is associated with calcite ± albite ± quartz alteration in fractures, vein networks, and crackle breccias. Mineralization is zoned from bornite ± chalcopyrite ± millerite with Zn, As, Mo, Ag, and U anomalies in the main orebody, through chalcopyrite-rich breccias with Zn anomalies, and chalcopyrite ± tetrahedrite vein networks with Sb, As, Ag, and Zn anomalies in the uppermost zone, to a Cu-depleted pyrite-rich envelope with Co anomalies, and finally to late, barren calcite veins in distal zones."

Jan 1, 2007

By Jean-Guy L. Gauthier

"With the Ontario Ministry of the Environment stipulating that the cumulative concentration of copper, lead, zinc and nickel in mine mill effluent must be no greater than 1.0 milligram per litre, it has become necessary for the mining industry of find some form of treatment for the removal of heavy metals from effluent waters.To comply with these guidelines, it became necessary for Mattabi Mines Ltd., which is situated 50 miles Northeast of Ignace in Northwestern Ontario, to develop a compact, cost effective and technically sound treatment process to remove heavy metals from their tailings overflow. A design committee consisting of mine metallurgists, environmental engineers, a Dutch research and development team and the equipment supplier engineering staff was set up to accomplish this.Using some new and innovative wastewater treatment equipment, the guidelines established by the Ontario Ministry of the Environment can now be met. The sludge produced from the precipitated heavy metals is sent directly to the concentrator, thus eliminating the danger of re-dissolution of the metals in a landfill site, while recovering some of the valuable metals that would otherwise be wasted in a sludge landfill."

Jan 1, 1980

By R. Drozd

"The Bullmoose Mine is currently under construction in the North East Coal area of British Columbia, and approximately $300 million will be spent to bring this 2.3 million-tonnes-per-year metallurgical and thermal coal mine into production by December 1, 1983.The project is an unincorporated joint venture undertaking, with Teck-Bullmoose Coal Inc., a wholly-owned subsidiary of Teck Corporation, holding 51%, Lornex Mining Corporation holding 39%, and Nissho-Iwai (Canada) Ltd. holding 10%. Bullmoose Operating Corporation will be the manager and operator of the project.This paper will broadly cover the history and exploration work on the property, the geology, open-pit mining plans and equipment, the preparation plant flowsheet from breaker station to clean coal silo, the 35 km highway truck haul, the railroad loadout system, manpower requirements, construction progress, approvals and permits, and general financial arrangements.IntroductionThe Bullmoose Mine Project"" is located about 87 road kilometres south of Chetwynd, B.C. and consists of an open-pit coal mine, a plant facility in the Bullmoose Creek valley below the mine, and a separate rail loadout facility on the British Columbia Railway Branchline near the new town of Tumbler Ridge some 35 road km to the east.The plant will be capable of producing a total of 2.3 million tonnes per year (mty) of washed metallurgical and thermal coal. Long-term metallurgical coal contracts for high quality, medium volatile, bituminous coal have been signed with nine Japanese buyers for 1.7 mty, and the balance of 0.6 mty will be thermal coal production.Plant construction began in the spring of 1982, and in May 1983, preproduction waste and overburden removal in the mine will commence. The plant should be fully operational by December 1983, and first vessel loading at the Ridley Island port is scheduled for January 1984."

Jan 1, 1983

By G. Mihaylov

The basic principles of systems analysis are presented. A model has been designed to determine the location of the Main opening in the presence of three or more stock orebodies. The necessary condition is to find a location for the Collection point which is an essential element in opening up each orebody (stock). The model takes into account the total transportation costs from each orebody to the collection point. Three variants are considered provided that the orefield is divided into two levels at least: - a collection point is designed at every level; - a collection point is designed at the lowest level, i.e. where the so-called concentration level is formed; - the collection point is located at a point between the planes of the two levels; The effect of the depth of mining and mine output on determining the method of opening up the orefield has been analyzed by considering a vertical and/or an inclined shaft. A function has been constructed which allows for investigating in both a static and dynamic regime the capital costs for constructing the whole complex including the shaft. The character of the function does not allow finding the global limits. Therefore, it is of particular importance to specify the limiting conditions. In this case these are the flow capacity of development openings and the shaft. The basic groups of cost and natural indicators for assessing and selecting an optimal technological solution have been systematized. The combined analysis of the two approaches to finding the location of the Main opening and determining the mining method enables us to determine when an inclined shaft is best, and the depth at which opening by a vertical shaft has no alternative. Thus, a transition area is formed for which the selection of an optimal technological solution requires an analysis similar to that proposed in this paper. Conclusions are finally drawn which serve as a basis for determining the areas of application of each opening, including the use of a combined scheme of mine opening. The approach presented can be used in both investigating the possibilities for opening up new orefields and reconstructing existing ones in cases when the mining operations go deeper.

Aug 1, 2013

By Ken G. Kress

Syphons can be a simple, reliable and proven alternative to otherwise more complex pumping systems or low level outlet works. In a simple form they consist of a pipeline constructed over the top of an embankment or high topographic feature, connecting a source pond to a receiving pond or channel (see Photograph 1). The syphon action is initiated by removing air from the pipeline (priming) using simple devices which can be purchased ?off the shelf?. Once primed, the syphon flow rate can be controlled or stopped using conventional gate, valve, orifice plate or other devices. Repriming is not required even if the flow is stopped, provided the syphon is not drained. A limiting factor in considering a syphon as a design option is the maximum lift (i.e., vertical distance from source pond level to summit of syphon) which is approximately 9 metres, or less, dependent on syphon pipe features and site conditions. Pipeline syphons can be quickly constructed from readily available materials including steel, polyethylene and PVC pipe. They are particularly well suited to many of the unique conditions often encountered at minesites. This paper identifies situations that can sometimes be best resolved using pipeline syphons. It provides basic principles for pipeline syphon design and includes case histories of their successful application.

May 1, 2001