Search Documents

By Jose R. Hernandez-Aguilar, Jeet Basi

"The study evaluated the impact on overall circuit metallurgy of improving the performance of the two flotation columns that make up the final Mo cleaning stage in the Cu/Mo separation circuit at Highland Valley Copper mine. The results showed that a key factor to improve the overall circuit metallurgy was to control the size of the bubbles generated in the columns. When a large proportion of small (< 1 mm) bubbles were generated, the production rate of solids-in-concentrate increased by a factor of 4-5 compared to typical production figures without compromising concentrate quality. This increase in concentrate production rate reduced the circulating load in the circuit causing a significant increase of Mo recovery. A statistical analysis of historical production data showed a strong relationship between final concentrate production rate and overall Mo recovery. This relationship along with the results from this study indicated an opportunity to increase the recovery of Mo from 90% (typical) to 94% without downgrading concentrate grade. This 4% increase represents about 14,000 lbs or $500,000 worth of Mo each month at current metal prices.To provide a rational interpretation of the results, this study also examined whether the model of Gorain et al. (1997; 1998; 1999) could explain the increase of Mo recovery seemingly resulting from the decrease of bubble size. The data showed that the model predictions did not agree with the experimental data, i.e., for a given change (decrease) of bubble size, the predictions underestimated significantly the observed recovery increase. An interpretation based on the fundamental analysis of Finch and Dobby (1990) and Hernandez-Aguilar et al. (2005) is proposed to explain the discrepancy between measurements and predictions obtained from Gorain et al.’s model.INTRODUCTIONIt is generally accepted that the size of the bubbles generated in a flotation cell – a concept usually referred to as “bubble size” – has a significant effect on metallurgical performance. However, a significant number of mineral processing practitioners often question, with valid reasons, the practical benefits of implementing process improvement strategies based on controlling bubble size. “Small” bubbles are often considered to be “favourable”, but how small they need to be for a particular case, or how to adjust operating conditions to control a target bubble size, or whether the bubbles need to be smaller in the first place are questions that usually remain unanswered. Two reasons explain this situation."

Jan 1, 2009

By G. Bellefleur, K. Stevens, E. Adam, D. Synder, G. Perron, C. Müller

The Downhole Seismic Imaging consortium was initiated by the Geological Survey of Canada and three Canadian mining companies to assess the usefulness of borehole seismic techniques for the exploration of massive sulphide deposits within areas of steeply dipping stratigraphy. Field tests were conducted over two sub-economic massive sulphide deposits located in Norman West, Ontario, and Halfmile Lake, New Brunswick, using various shot configurations and a three-component borehole receiver array. The Norman West deposit, or structures associated with the deposit, produce detectable seismic reflections as far away as 1500 m. However, these reflections are difficult to distinguish from fault reflections and lithological contacts near the base of the Sudbury Igneous Complex. At Halfmile Lake, the rock properties are favourable for direct orebody detection. The Halfmile Lake deposit has a clear but relatively complex seismic signature on the downhole data, showing not only P-wave reflections, but also strong reflected S-waves and modeconverted waves. Such prominent S-waves and converted waves have not been recognized previously in borehole or surface seismic data acquired over massive sulphide deposits. These waves add complexity to the interpretation but provide additional imaging capabilities. Reflected S-waves and converted waves should be considered when designing seismic surveys for mineral exploration.

Jan 1, 2004

By L. Flett, S. Woods, C. Deredin

"Following a significant reduction in world Imperial Smelting Furnace (ISF) capacity from 2003 to 2008, a major optimization initiative was successfully carried out on the lead upgrading and bulk (zinclead) flotation circuits in the Brunswick Concentrator.This paper describes the process improvements that have taken place in order to reduce the quantity of bulk concentrate:•,Increase in lead upgrading rougher flotation circuit capacity•,Installation of a closed-circuit bulk regrind utilizing MillPebs and 150 mm Cavex hydrocyclones•,Installation of two additional cleaner flotation stages on the bulk circuit•,Optimization of the manipulated variables in the lead upgrading and bulk circuitsINTRODUCTIONThe Brunswick Mine (Xstrata Zinc Canada) is located near Bathurst, New Brunswick and is one of the world’s largest lead/zinc mines. Milling of ore commenced in 1964 from the No. 12 orebody, with an expansion in 1966 to accommodate ore from the No. 6 open pit mine. The planned closure of the mine will take place at the end of the first quarter in 2013. The ore is a complex massive sulphide, consisting of approximately 20% valuable minerals, 60% pyrite and 20% silicates.A simplified flowsheet for the concentrator is given in Figure 1. The overall flowsheet involves SAG milling, secondary ball milling, selective flotation, and dewatering by thickening, filtering and drying. The complexity of the flowsheet evolves from the requirements for fine grinding and the production of four concentrates: zinc (sphalerite), lead (galena), copper (chalcopyrite) and bulk (sphalerite plus galena).Primary hydrocyclone overflow feeds the copper-lead aerator-roughers for flotation at pH 9.0 with soda ash. Plant xanthate (80-20 sodium isopropyl and potassium amyl) and AP407 are used as collectors in the copper-lead circuit. The rougher concentrate is directed to the copper-lead regrind circuit and the tailings are fed to the secondary grinding circuit. The secondary hydrocyclone overflow from the secondary grinding circuit feeds the copper-lead rougher-scavenger banks. Rougher concentrates are reground to a P80 of 28 µm prior to three stages of copper-lead cleaning. The first stage of cleaning is done in an open circuit with the tail reporting to the cleaner scavenger. The cleaner scavenger concentrate reports to the regrind circuit and the cleaner scavenger tail combines with the rougher/scavenger tail to feed the zinc circuit. The second and third stages of cleaning are performed in closed circuit with the cleaner tail being recycled to the copper-lead regrind circuit. The average final concentrate grades 23% Pb, 3% Cu and 704 g/t Ag, and is fed to the copper separation circuit."

Jan 1, 2013

By R. A. Hill, J. D. Pitts

"Long distance slurry pipeline systems have been successfully trans-porting steam coal, iron concentrates, copper concentrates and limestone for an aggregate of nearly 60 years and nearly three billion ton-miles annually. A phosphate concentrate pipeline is nearing start-up and systems for coking coal, lead/zinc concentrates and fly ash are planned. The solids pipeline concept, first patented in the early 1900's and commercialized in the 1950's, is now a proven technology providing an economic, environmentally pleasing and safe method for long distance bulk transport.The challenge for larger tonnage and longer distance movements of solids, for traversing increasingly rugged terrain in grass roots mineral developments, for transporting untried materials and for shipping more economic forms of proven materials still remains. This has necessitated continued refinements and optimization of the technology. The economic and environmental incentives for slurry pipelines when compared to other transport alternatives has justified substantial activity in this area. The scope of planned systems in coal, iron and other minerals is indicative of the firm place slurry pipelines will have in worldwide mineral development.In this presentation, the state-of-the-art in long distance slurry pipelines is reviewed with a focus on major systems of interest to the mineral processing industry. An overview of new developments in the application of this concept is presented, and finally, a projection of the future of pipelines in mineral development both worldwide and in Canada is discussed."

Jan 1, 1978

By Neil H. Brown

Outline ? Cameco - Cigar Lake ? Cigar Lake Mine Development ? MDS #1 ? MDS #1 Improvements ? MDS #2 ? MDS #2 Improvements Pending ? Acknowledgements Mine Development System ? Mining methods tested and developed over the years ? Construction began officially in 2005 ? Water inflow events in 2006 and 2008 ? Successful dewatering and re-entry in 2010 ? Remediation continues ? Production target is mid-2013

Oct 1, 2010

By D. Brand

"The risk management objective of the AMIRA Code of Practice for Metal Accounting has seldom been systematically investigated in the literature up to the authors’ knowledge. Risk is defined in the Australian Standard on Risk Management (AS/NZS 4360:2004), as “the chance of something happening that will have an impact on objectives”. The simplified economic analysis performed in this paper has lead to define “something happening” as measurement non-representativity and “impact on objectives” as NSR loss from the optimal NSR. This has pinpointed a missing link being the establishment of a relation between NSR in flotation plants and measurement representativity. The proposed framework, referred to as the total cost of representativity, answers the previously unanswered question of how much accuracy/reproducibility is fit for purpose in a given flotation plant. Authors readily acknowledge that it is way easier to assess the cost of accuracy/reproducibility than the cost of inaccuracy/irreproducibility. However, this exercise not only answers previously unanswered questions but also establishes an essential link with operational excellence. This paper exposes why such operational excellence could neither be attained nor proved without a state of the art metal accounting system. This should impact not only how metal accounting systems are audited/designed/refactored, but also how flotation plants are designed.IntroductionBecause representative metal accounting is a vital source of information for the financial accounts of a mining/metallurgical company, the need for a code on metal accounting was recognized in 2001 and a team was formed in 2003, under the sponsorship of several major mining houses, to produce such a code. Table 1 exposes the two main objectives of this AMIRA Code of Practice for Metal Accounting."

Jan 1, 2017

By C. Pelley, S. Kelebek, G. Kunzel, S. Gregersen, M. Pollanen

A series of small-scale tests was conducted to evaluate the effect of micro-fracture development, imposed by blasting, on the material properties of the rock as well as its resistance to crushing and grinding. The uniaxial compressive strength, tensile strength, Poisson’s ratio, Pwave, S-wave velocity, point load test index, crushing, and grinding work indices were evaluated for samples without any blasting load and for samples which had received a variety of blast loads ranging from a single impact with a lowstrength detonating cord to a combination of impacts at different times and significant impacts with powder factors close to those used in practical blasts. It was shown that the rock mechanics parameters change even at low impacts, suggesting easier crushing of the rock. Damage values appear to be affected by timing as stress wave superposition affects the damage process. Fragmentation is achieved at higher impact levels while work index modification of the fragments is also observed when high powder factors are used, suggesting improvements in grinding.

Jan 1, 2006

By S. K. Mitterecker, T. Hofbauer, F. Baerhold

"Acid regeneration is a very important process step in each acid leach circuit. It is required to recover dissolved metals and HCl from spent leaching acid. Andritz Metals presents its recently commissioned spray roast pilot plant. The facility is now available for testing and demonstrating acid recovery or metal oxide production which is a requirement in several flow sheets under development for the mining and specialized oxides industries. Results from pilot test campaigns are reported here. We are currently focusing on a nickel ore leaching process, which requires both a feasible iron control and acid regeneration step. In addition, we disclose the results of a magnesium ore and aluminium recycling test campaign conducted in our pilot plant facility.INTRODUCTION Hydrochloric acid regeneration is widely used in the steel industry to regenerate spent pickle liquors into hydrochloric acid at a typical concentration of 18 wt.%. Andritz Metals (formerly known as Ruthner) has built more than 200 acid regeneration plants worldwide (Andritz Metals brochure). As technology leaders Andritz also has vast experience with specialty metal oxide plants, producing metal oxides such as aluminium oxide (Al2O3), magnesium oxide (MgO), nickel oxide (NiO), cobalt oxide (Co3O4) and mixed oxides from metal chloride solutions (Baerhold F., Lebl A., Starcevic J., 2006), (Jedlicka, H., n.d.), (Ruthner M.J., Krischner H., 1973), (Ruthner Ind. Planungs AG, 1967). Hydrochloric acid leach circuits have been developed and proven in the industry for many years. Examples of industrial applications are: synthetic rutile production (TiO2) (Walpole E.A., Winter J.D., 2002), Quebec Iron and Titanium’s UGS process (Patoine M.-C., De Mori A., Borowiec K., Coscia C., 2002), magnesium and potassium production (Priemer H., 1973) and Goro Nickel (Vahed A., Colton D.F., Duterque J.P., Karner W., Baerhold F., 2004), (Taylor A., 2013). One of the critical process steps in developing a hydrometallurgical process is acid regeneration, as it is an economic requirement to recover both the dissolved metals and acid (commonly HCl) from the spent leaching solution."

Jan 1, 2016

By Robert Gannicott

??A mining company without the burden of operating a mine ??Management focused on marketing a high-quality, run-of-mine range of Canadian diamonds ??Robust revenue stream ??Specialist diamond knowledge ??Canadian exploration and development expertise ??BUT ??Single asset revenue base from depleting ore reserve ??Limited influence on production plans

Apr 1, 2005

By Jean Cayouette, Paul Blatter, Paul Cousin

"The Laronde mill was commissioned in 1988 and has been treating the Laronde Penna ore since 2000. The Laronde plant, situated in the Abitibi region of Quebec, has experienced mill expansions to accommodate 7500 mtpd and to recover gold and silver as well as important amounts of base metals (Cu, Zn, Pb). Ten sequential metallurgical and environmental processes are responsible for metals recovery and process viability. Over 200,000 ounces of gold, 4,5 million ounces of silver, 7000 tonnes of copper, and 78,000 tonnes of zinc are produced annually.In 2008, the Goldex plant began trucking high grade (35-45 g/t Au) pyrite sulphide concentrate (TCGO) for gold extraction at a newly constructed treatment plant, increasing gold output at Laronde by 40,000 ounces. In 2009, the high gold grade Lapa ore processing facilities were annexed to the Laronde plant increasing output by 120,000 ounces of gold. TCGO and Lapa productions are forecasted until 2018 and 2015 respectively, with known reserves of each mine.Today, up to 140 permanent employees run and optimise the Laronde plant operation. As a result, Laronde has intricacies intrinsic to a large and varied operation. The paper will outline the metallurgical highlights, challenges, and future outlook related to the treatment of each ore type (Laronde, TCGO, and Lapa).INTRODUCTIONFollowing the 2000 to 2003 expansions, the Laronde plant evolved into a mature milling complex with developed processing, man power, and water treatment capabilities able to accommodate the complex Laronde ore. The ore requires a series of grinding, copper/lead flotation and separation, zinc flotation, zinc tails precious metals leaching, followed by a counter-current decantation circuit and Merrill Crowe precipitation. A paste backfill and SO2-air cyanide destruction operate intermittently. The tailings area has a dedicated cyanide destruction and metals precipitation plant prior to water recycling to the mill. A biological water treatment plant was put into service in 2004 to address the build-up of thiocyanate in the tailings ponds at Laronde. This was the result of the high sulphide content of the Laronde ore and 90% recirculation of the process water. The plant uses bacteria to oxidize and destroy thiocyanate, and removes phosphate from the water before it is released to the environment."

Jan 1, 2011

By S. Kelebek, E. Yalcin

"Two composite samples of a gold-bearing ore from North Western Quebec (Barry Township) were tested to assess their grindability, recovery by flotation and Knelson concentrator as well as extraction using cyanidation.Work index values (BWi) for two composites were found to be 10.4 and 11.0 kWh/tonne, respectively. Flotation tests involved feed samples for which the particle size ranged from a P80 value of 205 ?m to 53 ?m, which resulted in gold recoveries of 91.8% to 95.8% (at gold grades of 130 to 140 g/tonne). Cyanidation tests indicated gold extraction levels ranging from 94.2 to 97.5%. Higher, recoveries were obtained at finer grind sizes and higher cyanide strengths. However, the grind size had a bigger impact on gold leaching. Gold grade and recoveries obtained with the Knelson concentrator device were lower than those obtained by flotation. Mass recoveries to concentrate products strongly depended on the fluidization pressure used. High gold recoveries can be obtained generally at low water pressures of 3 to 4 psi. Higher water pressures produced more selectivity at the expense of higher gold losses.It can be concluded that the gold ore samples tested have good characteristics due to moderate levels of energy requirement, high gold recoveries and extraction rates attainable.INTRODUCTIONBench scale testing of ore samples is an important step in the long series of metallurgical and economic studies involved in bringing new ore bodies into production (Coleman, 1980). Through a laboratory testing program, the behaviour of an ore in a particular process on a larger scale can be established. In an exploratory manner, this testing can be helpful for classification of ores in terms of “good ore” or “problematic ore” by providing preliminary information on recoverability of target minerals. Potential problems if any can be assessed by further investigation of products (e.g., middlings) obtained as a result of testing. A detailed bench scale experimental program in the metallurgical laboratory can also provide the background work for flowsheet development. Depending on the simplicity or complexity of the ore to be tested and type of details required from a testing program, the amount of samples required in the mineral processing laboratory can vary from several kg to more than one hundred kg depending on how detailed the metallurgical testing program is."

Jan 1, 2008

By Mehmet Canbazoglu, Kaarlo Haavanlammi, Hannu Laitala

Cobalt is currently a critical metal because of the increasing number of electrical vehicles forecast for production. Copper and zinc are base metals that are used in many everyday applications, including vehicle production. Eti Bakir Co. Mazidagi Phosphate Plants in the Mazidagi district of Mardin, Turkey is a multi-product facility that produces cobalt, copper, and zinc, as well as fertilizers, from the roaster calcine. Roaster off gas is treated in a sulfuric acid plant (SAP) and the acid itself is utilized in fertilizer production. The comminution circuit, roaster, SAP, and calcine leaching process were developed by Outotec and integrated with the fertilizer production process implemented by Eti Bakir A.Ş. This paper describes the hydrometallurgical calcine leaching process used at the plant, with a focus on the oxidative pressure leaching of the cobalt, zinc, and copper-containing calcine. The cold and hot commissioning phases of the pressure leaching autoclave start-up are discussed together with experiences from the ramp-up period. The production processes of the copper cathode and cobalt and zinc-containing salts are also presented together with some of the plant’s operating parameters. INTRODUCTION The ETI Bakir A.S. fertilizer plant, Turkey, is located in Mardin Province near the border with Syria, (Figure 1). The leaching plant project was started in 2012. The purpose of the plant is to separate the valuable metals from the calcine produced by the pyrite roasters, which are used to produce a SO2 containing gas for the new sulfuric acid plant. Fertilizer production requires sulfuric acid, and for this reason a sulfuric acid plant was built; customer already had access to pyrite concentrate, which is used as the roaster feed. During the engineering phase of the roaster and acid plants it was noticed that the roasted calcine contained considerable amounts of valuable metals like cobalt, copper, and zinc. To recover these metals, a calcine leaching process was developed at the Outotec Research Center in Pori, Finland. The main process connections of the Mazidagi site are shown in Figure 2.

Jan 1, 2019

By Graham Davey

"Ultrafine grinding of minerals has been in wide spread use in the industrial mineral field for over 30 years. Within the last 10 years the metalliferous industry has shown interest in the ability to produce ultrafine particles, as chemical, physio-chemical and physical separation processes have advanced to be able to treat ultrafine metalliferous particles. Also as the primary mineral deposits are depleted, new more difficult deposits must be mined. Existing operations are also looking to maximize economic return from existing deposits, requiring new thinking and technologies.The recent development of industrially proven and cost efficient technologies for ultrafine grinding has opened up another processing option for the treatment of finegrained metalliferous and refractory gold ores. The current commercial designs are variations of stirred mills used in the industrial minerals sector for the past 30 years. For the purposes of this paper ultrafine grinding is considered to be P80 of less than 15 microns.Attrition milling to fine grind sizes presents some challenging issues relating to scale-up including the dearth of information on the quantitative impact of feed and operating conditions, as well as the precise and accurate measurement of particle size distributions. Two examples from recent installations will be analyzed including Thalanga Copper and Century Zinc Mines. Both have diverse grind size targets for the SMD, yet both have realized significant metallurgical gains."

Jan 1, 2002

By K. Loutet, A. Guenkel, K. Nikolaisen

"The INCO SO2/air process was patented by INCO in 1985. Well over 80 mining operations worldwide are using this process to oxidize cyanides to cyanates in the tailings from gold, silver and copper mining operations. The sulphur dioxide (SO2) for this process can be supplied either as liquid SO2, SO2 gas or as a sulphite-based salt. The majority of SO2/air operations have used sulphite-based salts as the ‘SO2’ equivalent probably due to low capital cost. Liquid SO2 has also been used frequently, but due to concerns with safety and availability, this option is often not preferred. The solid salt sodium meta-bisulphite (SMBS) is commonly employed, but its cost is an order of magnitude higher than that of sulphur. Due to the high cost of SMBS, the increased capital cost for a sulphur-burning SO2 gas plant (green field or retrofit) usually has a pay-back of less than three years. In addition, a SO2 gas plant offers potential for significant heat recovery from the sulphur burning process. In terms of safety, the SO2 gas plant only requires the storage of relatively benign sulphur and the site inventory of SO2 will be limited to the plant gas volume. Therefore, a SO2 gas plant will not trigger the Canadian Environmental Protection Act (CEPA) E2 Regulations or the US Clean Air Act Section 112(r) accident prevention regulations, as may be the case for liquid SO2.Most existing mining operations using ‘SO2’ are gold operations, but in recent years there has been an increased interest in larger sulphur dioxide gas plants for hydrometallurgical facilities that employ leaching of cobalt/manganese minerals or precipitation of manganese/iron (e.g. Tenke Fungurume and El Boleo).This paper focuses on the production of sulphur dioxide gas generated on site and on demand for the use in hydrometallurgical processes. The capital and operational costs of a SO2 gas plant is compared to conventional process alternatives using sulphite-based salts or liquid SO2."

Jan 1, 2016

By Michael Young, Josh Rubenstein, Michael Cooper, Tom Shouldice, Dan Curry

"Xstrata Nickel Australasia’s Cosmos plant in Western Australia is currently implementing a debottlenecking project to increase nickel output while maintaining metallurgical performance and a low unit cost for production. Mineralogical analyses indicated that the processing bottlenecks could be removed by simply reconfiguring portions of the circuit as well as adding capacity with technical advancements – notably an IsaMill™, Jameson Cell, Wemco® SmartCell™ and Larox Filter.The Wemco® SmartCell™, which is particularly suited for coarse mineral flotation, and Jameson Cell, which is particularly well suited for fast floating and fine minerals, combine as rougher scalpers to complete the main stream portion of the flotation circuit. Addition of the two new cells meet the required flotation capacity to handle the forecast increase in nickel feed grade and tonnage.The addition of an IsaMill™ for regrinding allows the SAG mill to produce a coarser primary product, thus enabling increased throughput. The advantages offered by the IsaMill™ include operation in open circuit (internal classification), an inert grinding environment (ceramic media) for better downstream flotation (“clean” new surfaces), compact footprint (easy to retrofit into existing plant) and energy efficiency. With the new rougher capacity addition, the remaining original plant cells were reconfigured to suit the new regrind mill and cleaning requirements. The existing 24 m2 Larox pressure filter was replaced with a larger 32 m2 unit to dewater the increased concentrate output.The paper describes the upgrade at the Cosmos concentrator with particular emphasis on the mineralogical data and metallurgical benefits associated with the changes.INTRODUCTIONThe Cosmos concentrator is located 680 km northeast of Perth in Western Australia. The deposit’s development and operations were started in 1999 by Jubilee Mines NL, Cosmos’ previous owner, with the first production of nickel concentrate in April 2000. The Cosmos concentrator treats a komatiite hosted high grade nickel sulphide ore, with sulphides being predominantly pentlandite and pyrrhotite with lesser amounts of pyrite and chalcopyrite."

Jan 1, 2010

By Sylvain Létourneau

Help organizations maximize the benefits of the data that they collect ? perform scientific research in: machine learning, data mining, statistics, artificial intelligence, soft computing, information retrieval, information systems, and natural language processing ? preferred application areas: Equipment Health Management, Bioinformatics, Health, Web Mining ? today?s talk limited to Equipment Health Management While the aircraft is still in the air, IDS: ? clusters relevant WRN, FLR, and snag (pilot) messages ? identifies probable causes based on TSM and provide links to corresponding TSM pages ? assesses MEL conditions (GO, NOGO, GOIF, ?) ? displays relevant maintenance history, suggests fixes based on similar cases ? Commercialization with MxI Technologies Ltd and Air Canada in 2000

May 1, 2008

About MAC ? The national organization of the Canadian mining industry ? Mining, smelting and refining of base and precious metals ? Mining of iron ore, diamonds, uranium, oil sands, coal and industrial minerals ? Many associate members ? www.mining.ca

Aug 1, 2013

By Fathi Habashi

"Crushing and grinding of ores and their beneficiation by washing away gangue minerals has been practiced since ancient times. Primitive crushing was done by hand pounding the ore with a hard stone then by using metallic hammers. The mortar and pestle was mechanized using a lever and when the size of operations increased in the middle ages, the stamp mill was introduced. The grindstone played an important role in grinding of ores. Panning for gold and hand sorting of minerals were two old methods of separation, now gave way to modern techniques. Flotation started in the middle of the nineteenth century by using oils to collect the mineral particles and float them on the surface of the aqueous slurry. It was only in the 1920s when it was discovered that organic compounds were affective floating agents. Textbooks written by distinguished engineers such as Rittinger, Rickard, Pryor, Taggart, Richards, Gaudin, and others contributed to the recognition of this field as a new discipline to be taught in Universities. INTRODUCTIONThe ancient Egyptians knew already that it would be easier to melt an earth rich in gold particles than another which is poor. As a result all efforts were made to enrich the gold by washing away the light gangue minerals (Figure 1). Another ancient method for enriching gold particles from a river stream was by means of fleece, hence the Greek myth of the “golden fleece”. The present day Georgia was known in ancient times as Colchis and was a center for gold working. It was known to the ancient Greek as the land of Golden Fleece. The use of special cloth to catch gold particles was also described by Agricola in his 1555 book De Re Metallica (Figure 2)."

Jan 1, 2009

By K. G. Wheeland, J. E. Dutrizac, M. Wasserlauf, A. A. Condy

Numerous processes for the treatment of thiosalts in base metal milling effluents have been examined in the past decade. Flowsheets for thirteen processes are outlined, and cost estimates are presented for a base case of a 720 mi/h effluent flow containing 1400 mg/L thiosalts. The processes are ranked on the basis of Numerous processes for the treatment of thiosalts in base metal milling effluents have been examined in the past decade. Flowsheets for thirteen processes are outlined, and cost estimates are presented for a base case of a 720 mi/h effluent flow containing 1400 mg/L thiosalts. The processes are ranked on the basis of

Jan 1, 1988

By Pablo González, Rodolfo Espinosa, Jose-Luis Noyola, Sergio Cossio

"Minera Penmont, at La Herradura, is a joint venture between Industrias Peñoles, S.A. de C.V., and Newmont Mining Corporation. The mine is located in the northern Mexican state of Sonora. La Herradura consists of an open pit mine with two-stage crushing and heap leaching facility, the gold is recovered from the pregnant solution using the Merrill-Crowe process; production began in July 1998. La Herradura produces about 130,000 gold ounces per year, and treatment capacity is 22,000 tonnes/day. Ore mineralization occurs in a shear zone with quartz and native gold. Gold distribution is quite heterogeneous due to the coarse visible gold, in some coarser particles ranging from 100 to 600 microns.Sampling and assaying protocols where established during exploration and prior to starting up operations, based on nomographs developed from early heterogeneity tests. But, as the coarse gold problem became noticeable, it was necessary to develop new sampling protocols to have an acceptable relative standard deviation to control the fundamental error within ± 15%.An experimental program was developed and conducted on a selected ore block made of 195 blastholes; regular ore grade control procedures were applied to both sets of data to evaluate the difference in results between the protocol established prior to starting up operations (“existing”) and the new protocol (“leaching”). In the “existing” protocol, subsampling is done through riffle splitters, and coning and quartering. Fire assaying is used to estimate the gold content, on a 50 g sample. In the “leaching” protocol a 12,000 g sample was bottle rolled cyanide leached, and the leach residue was assayed on a 50 g sample using fire assaying, and a weighted average total gold content was calculated. Currently, a new alternative method is being evaluated, where sub-sampling is done using rotary splitters, and fire assay on a 50 g sample; in this “rotary sampling” protocol and for comparison purposes, gold assays were also repeated using the “leaching” protocol.Test results were compared in three groups < 0.30 g/t (below cut-off), 0.30 to 0.8 g/t, and >0.8 g/t. Overall. Results show that the protocol established prior to starting up operations underestimates the gold assays. Detailed technical results, alternative options, and their implications are discussed in the paper."

Jan 1, 2003