Search Documents

By H. F. Letient, D. C. Johnson

At the 25th Annual B.C. Mine Reclamation Symposium in September 2001, Huckleberry Mines Limited received the Jake MacDonald Reclamation Award for its exemplary mine waste management plan, conceived to prevent the onset of acid rock drainage (ARD) and facilitate reclamation of the site. The mine is an excellent example of a total mine waste management plan, with all materials scheduled in detail for the life of the mine. The filling plan for the waste management facility takes into consideration the requirement for permanently flooding the potentially acid-generating rock. From an acid generation point of view, the tailings fall in the zone of potentially acid-generating material. To avoid long-term ARD concerns, it is planned to float pyrite out of the tailings toward the end of the mine life, thereby generating a non-potentially acid-generating tailings stream which will be used to cap the deposited mine waste. The pyrite-rich tailings will be discharged into the deeper portion of the impoundment. On closure, a permanent water cover will be maintained over the mine waste. Only beaches of non-potentially acid-generating tailings will remain exposed. Mining will be phased to also allow one of the pits to provide storage for potentially acid-generating rock and to be flooded at the end of mine life.

Jan 1, 2004

By G. S. Crawford

Forecasts prepared by the B.C. Research Council for the National Harbours Board suggest that mineral shipments through B.C. Lower Mainland port facilities will increase more than four-fold, from 6 to about 25 million tons, during the decade 1965 to 1975. The longer term outlook is for a six-fold increase to about 35 million tons by 1985. In 1967, minerais accounted for more than one-third of the total deep-sea traffic tonnage, nearly as much as grain. By 1975, the minerals' share will be about half the total. The principal items are exports of potash from Saskatchewan, and of coal and sulphur from Alberta and British Columbia. Additional exports include copper and other mineral concentrates and propane. Imports are chiefly salt and phosphate rock. Coastal traffic in such items as cement, sand and grave!, and limestone totalled 3.3 mil-lion tons in 1967. They will continue to be of major importance, but do not have the spectacular growth potential of the deep-sea traffic.

Jan 1, 1968

The information in this document has been prepared as at February 16, 2011. Certain statements contained in this document constitute ?forward-looking statements? within the meaning of the United States Private Securities Litigation Reform Act of 1995 and forward looking information under the provisions of Canadian provincial securities laws. When used in this document, the words ?anticipate?, ?expect?, ?estimate?, ?forecast?, ?will?, ?planned?, and similar expressions are intended to identify forward-looking statements or information. Such statements include without limitation: statements regarding timing and amounts of capital expenditures and other assumptions; estimates of future reserves, resources, mineral production, optimization efforts and sales; estimates of mine life; estimates of future internal rates of return, mining costs, cash costs, minesite costs and other expenses; estimates of future capital expenditures and other cash needs, and expectations as to the funding thereof; statements and information as to the projected development of certain ore deposits, including estimates of exploration, development and production and other capital costs, and estimates of the timing of such exploration, development and production or decisions with respect to such exploration, development and production; estimates of reserves and resources, and statements and information regarding anticipated future exploration; the anticipated timing of events with respect to the Company's minesites and statements and information regarding the sufficiency of the Company's cash resources. Such statements and information reflect the Company's views as at the date of this document and are subject to certain risks, uncertainties and assumptions, and undue reliance should not be placed on such statements and information. Many factors, known and unknown could cause the actual results to be materially different from those expressed or implied by such forward looking statements and information. Such risks include, but are not limited to: the volatility of prices of gold and other metals; uncertainty of mineral reserves, mineral resources, mineral grades and mineral recovery estimates; uncertainty of future production, capital expenditures, and other costs; currency fluctuations; financing of additional capital requirements; cost of exploration and development programs; mining risks; community protests; risks associated with foreign operations; governmental and environmental regulation; the volatility of the Company's stock price; and risks associated with the Company's byproduct metal derivative strategies. For a more detailed discussion of such risks and other factors that may affect the Company?s ability to achieve the expectations set forth in the forwardlooking statements contained in this document, see the Company's Annual Report on Form 20-F for the year ended December 31, 2009, as well as the Company's other filings with the Canadian Securities Administrators and the U.S. Securities and Exchange Commission. The Company does not intend, and does not assume any obligation, to update these forward-looking statements and information. Marc Legault, a Qualified Person and the Company?s Vice-President, Project Development, reviewed the technical information disclosed herein. For a detailed breakdown of the Company?s reserve and resource position see the February 16, 2011 press release on the Company?s website. That press release also lists the Qualified Persons for each project.

May 1, 2011

By Chris Larsen, Carole Fortin, Dave Scott, Curtis Deredin, Ian Orford, Jean Guy Gauthier, Andy Trusiak, Lyne Côté, Mike Cooper

"Upon successful commissioning of the Stage Grinding Project (Cormier et. al., 2002), process improvements predicted through pilot plant testing were obtained in several flotation circuits, resulting in higher grades and recoveries for zinc and lead concentrates. Subsequent to establishing new baseline operating conditions from the Stage Grind Project implementation, additional opportunities were identified, and through the application of Six Sigma methodologies further gains were made. Six Sigma improvement projects were carried out in the copper-lead, zinc, lead upgrading and bulk flotation circuits. The overall performance increase resulting from incremental improvement projects has been substantial.Most remarkably, given the operational maturity up to the late 1980’s, the Brunswick concentrator team has continued to deliver a steady stream of major improvements over the past fifteen years. While senior managers and their programs have changed several times, there have been some critical constants over the long run. Common elements have been a commitment to team work, a commitment to recruit and maintain technical personnel, a structured business improvement framework supported organizationally by senior management, and focus on a few priority initiatives rather than trying to fix everything at once.The paper briefly discusses the longer term setting and then endeavors to illustrate, with examples, how improvements are presently achieved by applying the Six Sigma quality program.INTRODUCTIONThe Noranda Inc. Brunswick Mine, located near Bathurst, New Brunswick, is one of the world’s larger lead/zinc mines. Milling of ore began in 1964 from the No. 12 orebody, with an expansion in 1966 to accommodate ore from the No. 6 mine. In excess of 100 million tonnes have been milled to date. The concentrator employs differential flotation to produce lead, zinc, copper, and lead/zinc bulk concentrates. The ore is massive sulphide, with approximately 20% valuable minerals, 60% pyrite and 20% silicates."

Jan 1, 2005

By R. Kwiatkowski

Agenda ? Health Canada Protocol _ Screening Level Risk Assessments (SLRAs) Contaminants Foods Exposure Pathways COPCs _ Site Specific Risk Assessments (SSRAs) In-depth, quantitative Monitoring Exposure estimates Food Issues in Environmental Impact Assessments ?Country Foods? ? Foods gathered from the project area and consumed by local residents.

Apr 1, 2005

By S. A. H Tyrrell, R. Rotzinger

"Taseko Mines Limited recommenced operation of the Gibraltar copper-molybdenum mine in 2004 and embarked on series of development projects to modernize the mine and increase throughput capacity. The Gibraltar Development Plan 3 (GDP3) project included a second stand-alone copper-molybdenum concentrator, a stand-alone molybdenum separation plant and associated services. Ausenco was contracted to commence the detailed design in 2Q2011, commissioning commenced in 4Q2012 and first ore was processed in 1Q2013. This paper discusses the design, implementation and commissioning of the GDP3 Concentrator.INTRODUCTION The Gibraltar Mine (Gibraltar) property is located in the Cariboo Region of south central British Columbia, approximately 360 kilometers northeast of Vancouver. The site is accessed via an 18 kilometer paved road from the town of McLeese Lake, which is located on the province’s main north-south highway between the cities of Williams Lake and Quesnel. Gibraltar was originally developed by Placer Development and commenced production in 1972. Gibraltar was acquired, while on care and maintenance, by Taseko Mines Limited (Taseko) in 1999 during a period of unusually low metal prices. Taseko recommenced operations at Gibraltar in 2004, and embarked on series of development projects to modernize the mine and increase throughput capacity. The 1972 Gibraltar process flowsheet incorporated two-stage crushing followed by rod and ball milling and flotation. In 2008 Gibraltar completed their first development stage that included the installation of a SAG mill, converting the existing rod mills to ball mills and adding additional flotation capacity. Gibraltar continued development with the installation of an in-pit primary crusher, expansion of the bulk regrind circuit, expansion of the cleaner flotation circuit, replacement of the tailings pumping system and replacement of the concentrate filters and dryer."

Jan 1, 2014

By Paul Gauthier

Aujourd?hui, avec un faible prix de l?or sur le marché, les opérateurs miniers doivent revoir leur façon de faire. La méthode de minage «Eureka» permet de réduire les coûts de production et d?accélérer la mise en production des chantiers. Les principales étapes du cycle de minage et les problématiques associées à l?utilisation de cette méthode à la Mine Bousquet y sont décrites.

Oct 1, 2001

By Jon R. Maki

"EVTAC, an iron ore mine in Minnesota, had trouble meeting the customer’s pellet silica requirements. In addition, the mine plan was moving towards a lower grade ore and funding was not available for plant improvements to compensate for the change in ore or improving quality. Small changes to optimize various processing equipment resulted in significant improvements in both quality and productivity; for example, productivity on one mill line increased by 10% while producing lower silica concentrate. This paper will provide the methodology that allowed EVTAC to improve quality and productivity through process optimization with little capital investment.INTRODUCTION EVTAC, an iron ore mine in Minnesota, had trouble meeting the customer pellet silica requirements. In addition, the short-term mine plan was changing to a lower ore grade. Because of limited funds, EVTAC did not have the capital for investing in the plant to compensate for the ore change or to make improvements to lower product silica levels. Small changes to optimize process equipment resulted in significant improvements in quality and productivity; for example, one mill line feed rates increased by 10% while also producing a higher quality concentrate. These changes were sufficient enough to allow the mine to lower the target ore grade beyond their initial goal. At one time, a $3M flotation facility was considered as a way to meet quality with the new ore grade. However, the process changes were able to accomplish the same silica reduction with roughly a $50,000 investment in VFDs for sump controls. This paper will discuss some of the modifications that allowed EVTAC to meet the quality and production objectives with little capital investment. It also discusses the methodology used to make these process improvements."

Jan 1, 2014

By M. Kalin

"SUMMARYWaste management in general, and the water treatment of mine and mill effluents, has become an ever increasing burden for mining operations. A reduction in these expenditures would undoubtedly be desirable if this could in fact be achieved within effluent guidelines and monitoring requirements.A brief summary is presented of the research which has as its aim the development of methods which would reduce such costs and lead to solutions for environmentally acceptable close-out conditions for acid generating mine waters. The basic concepts of Ecological Engineering and Biological Polishing are presented, together with an indication of the present state of these research efforts. Details are provided of the progress of various experiments which aim to promote reducing conditions, organic matter production and the establishment of biological filters which remove metals from the water which are then retained within the waste management areas. These conditions should lead to a curtailment of acid drainage and an improvement in effluent quality.A description is provided of the first pilot demonstration using this approach to achieve a walk-away condition for the close-out of a massive sulphide tailings resulting from 10 years of operating a copper/zinc concentrator in Northern Ontario.1.0 INTRODUCTION1.1 Waste management and close-outIt is recognized that the achievement of a cost-effective and competitive mining operation, from the commencement of exploration for ore bodies through to the day-to-day efficient operation of the mine, requires a certain expertise and sophistication. However, the environmental effects of these activities are considered peripheral issues and their importance as an integral part of the planning and development of the mine/mill, is not always appreciated."

Jan 1, 1988

By L. Salnais

"Aluminum alloy structural components f or aircraft designed prior to the early 1970s, were machined from 2024, 7075 and 7079 plate, bar and forgings in either the T3xxx of the T6xxx tempers. Protective treatments for these parts consisted of chromic acid anodizing and alkyd zinc chromate primer, plus a nitrocellulose lacquer for exterior parts.The major service problem with these parts was the frequent occurrence of exfoliation corrosion and stress corrosion cracking (S. C. C.). Therefore, 2024 and 7079 alloys, with min or exceptions, were not used in aircraft designed after the early 1970s. Replacement materials were 7075 and 7050 alloys in the overaged, exfoliation corrosion and S. C. C. resistant, T73xxx tempers.The use of improved materials together with the upgrading to chromated epoxy primers, polyurethane enamels and the introduction of water displacing corrosion inhibiting compounds have significantly reduced corrosion in aircraft. IntroductionThe prevention of corrosion in aircraft has been a challenge to aircraft designers for many decades. With the design of the first all-metal aircraft, the designer and builder were thrust into the relatively new field of protective treatments as corrosion started to become more prevalent. This resulted from the continually increasing importance and wider utilization of aircraft, and their exposure to a wider variety of ho stile environments such as urban industrial pollution, high humidity tropical areas and salt ladened marine environments.Corrosion advanced another significant step when, after World War II, designs of new and larger aircraft utilized larger and thicker metal sections in the manufacture of structural components. With thicker mill products came higher residual heat treat, fabrication and assembly stresses resulting in an increased number of stress corrosion and exfoliation corrosion problems.Apart from the exterior environment, aircraft interior s can be exposed to a number of fluids which are either directly or indirectly responsible for corrosion. The most common of the fluids is water which is usually introduced as a result of condensation, especially in pressurized fuselages, and spillage from lavatories, galley s and electrolytes from batteries. These fluid s have a degrading effect on protective treatments and are also corrosive to the substrate metal. Fluids such as phosphate ester hydraulic fluids and ester based turbine engine lubricating oil s are not corrosive to the substrate metal, albeit they do contribute to corrosion by the degrading effect on protective treatments."

Jan 1, 1988

By Robert J. Maron, Mark Fernald, Alex Van der Spek, O’Keefe. Christian, Tim Bailey

"Sonar array-based non-invasive flow measurement technology is becoming an accepted and many times a preferred method of measuring challenging single and multi-phase flows in the mineral processing industry. This fundamental sensor and measurement technology has been extended to two developments that provide new measurement capabilities useful for monitoring and managing slurry flows and pipes.The first development is the non-invasive measurement of real-time velocity profile of slurry flow in horizontal pipes. Multiple non-invasive passive sensors measure localized velocities and are combined to provide a velocity profile measurement. This information can be used to determine the approach and onset of solid deposition on the bottom of the pipe. Having this information in real time can enable operation at lower velocities and/or higher solids concentration while avoiding solids deposition or plugging and its associated operational costs.The second development is the non-invasive measurement of pipe wear on slurry lines. Presently, such measurements are made by hand-held portable ultrasonic thickness gages. The numerous shortfalls associated with the manual method are overcome with a set of permanently or semi-permanently installed transducers clamped onto the outside of the pipe. This ring of sensors contains a series of conformable ultrasonic transducers spaced around the circumference, which are used to measure the thickness of the pipe under their respective locations. Compared to manual methods, this system and approach results in better repeatability and accuracy. It also decreases inspection labor costs and pipe access requirements. The minimal accuracy variations in the presence of varying environmental temperatures will be shown. Trending of pipe wall thicknesses in high wear pipelines will be illustrated. The benefits of significantly improved pipe wear monitoring in hydrotransport lines with abrasive solids, and associated improvement in the ability to insure safe operation and avoidance of costly environmental damage due to leaks caused by pipe wear will be discussed."

Jan 1, 2009

By A. J. Hynes, Lutes. G. G., Ravenelle. J. -F.

"The Anomaly A area of the Clarence Stream gold deposits in southwestern New Brunswick contains mineralized structures that bear geometrical relationships to regional folding events. The four mineralized zones of Anomaly A (AD, MW, 93, and Murphy) are hosted by turbiditic graywacke, quartzose wacke, siltstone, and argillite sequences of the Kendall Mountain Formation. A regional scale structural analysis reflects at least four deformational events, three of which appear to control the folded geometry of Anomaly A (D2, D3, and D4). F2 and F3 folds are coaxial and are refolded into a dome and basin geometry by F4 folds. The mineralized zones are subparallel to axial surfaces of F2 folds. Structural analysis of a mineralized zone exposed at surface indicates that gold mineralization is hosted by a quartz-vein system that comprises veins generated during both D2 and D3. Threedimensional representations of Anomaly A created using drill-core data and ®GoCAD suggest that the quartz-vein system was emplaced in fault structures during D2 as well as within brecciated dilation zones during D3. Three of the four zones that make up Anomaly A have F2 hinge surfaces that can be linked through a geometry compatible with the style of F3 and F4 folds. The apparent continuity of these three zones indicates the potential for kilometer-scale mineralized structures at Anomaly A. Le secteur de l’Anomalie A du gisement aurifère Clarence Stream contient des zones minéralisées qui montrent des relations géométriques avec les épisodes de déformation régionale. Les quatre zones minéralisées de l’Anomalie A (AD, MW, 93, Murphy) sont comprises dans une séquence turbiditique composée de grauwacke, de wacke quartzitique, de siltstone, et d’argilite appartenant à la Formation de Kendall Mountain. Des quatre épisodes de déformation étudiés par l’entremise de cartographie structurale, trois semblent contrôler la géométrie de l’Anomalie A (D2, D3, et D4). Les plis P2 et P3 sont coaxiaux et sont replissés en dômes et bassins par les plis P4. Les zones minéralisées sont subparallèles aux plans axiaux des plis P2. Une analyse structurale effectuée sur une zone minéralisée exposée à la surface indique que la minéralisation aurifère est localisée dans un système de veines de quartz qui contient des veines générées durant D2 et D3. Des représentations en trois-dimensions créées avec le programme informatique ®GoCAD à partir de données de forages suggèrent que le système de veines est localisé dans des zones de failles D2 ainsi que dans des zones de dilatation associées avec D3. Trois des quatre zones qui forment l’Anomalie A possèdent des plans axiaux P2 qui peuvent être liés par l’entremise d’une géométrie qui respecte le style des plis P3 et P4. La continuité apparente de ces trois zones indique qu’une structure minéralisée pourrait s’étendre sur plusieurs kilomètres dans le secteur de l’Anomalie A."

Jan 1, 2008

By Michael G. Rulff, Tracy M. Holmes

"Vast amounts of time and money are spent fighting flow problems in plants that involve the handling or processing of industrial minerals. Because these types of projects tend to be capitalintensive, the right decisions, made at the design stage, can have a substantial positive effect on the economics of the project.Some of the problems related to solids flow in mineral processing plants include:•,Flow stoppages•,Uncontrolled flow•,Segregation of blended materials•,Build-up and dead material resulting in loss of live capacityUnfortunately few Universities in North America provide courses in the design or selection of bulk solids handling equipment, let alone the theory of bulk solids flow, with the result that engineers do not fully appreciate the effects of bulk solids handling on their process. The usual method of selecting “standard” equipment, all too often, leaves plant operators hammering on hoppers to promote flow, a technique that is not only usually ineffective but also unsafe and often causes damage to equipment. In short, too little consideration is given, at the design stage of projects, to the particular material and operating environment involved and how these will affect handling between process steps.This paper seeks to give a general understanding of bulk solids flow theory including flow patterns and flow property tests, and presents functional design guidelines to ensure reliable flow. As well, a case history will be presented. Our message is clear: To ensure uniform, reliable flow, a plant design must take into account the specific flow characteristics of the bulk solid to be handled or processed."

Jan 1, 2008

By Klaus Tietz, Hamish Adam, John Selby, Ian Glazier, Brian Sinfield

"Room-temperature tunable diode laser (TDL) analyzers are gaining in acceptance for highly critical safety monitoring applications in a variety of industries. This paper describes the testing, evaluation and deployment of a laser-based hydrogen cyanide monitoring system at the Campbell Complex of Goldcorp’s Red Lake Gold Mines in Balmertown, Ontario, Canada.A trial, single channel installation was followed by a staged multi-channel installation. Unexpected technical issues with the multi-channel installation were addressed and resolved.INTRODUCTIONLaser-based gas detection has several advantages over existing gas detection techniques (Ballangrud, 1993; Silver, 1992; Bomse, 1995; Table 1). For practical purposes, lasers generate light at a single wavelength. Room temperature tunable diode lasers (TDL) emit light in the near infrared (NIR) part of the electro-magnetic spectrum. Many gases of interest, including HCN, NH3 and others, absorb energy in the near infrared (NIR). Each gas has a unique absorption signature, or spectrum, made up of a large number of individual “absorption lines”. A TDL can be tuned to select a single absorption line of a target gas, which does not overlap with absorption lines from any other gases. Therefore, laser gas sensing is selective and does not suffer from interference from other gases. The single-wavelength nature of laser light also means that laser gas analysers have a linear response over a wide dynamic range.Tunable Diode Lasers (TDL) generate only a few mW of power. However, all this power is concentrated at one wavelength, the wavelength where gas absorption occurs, resulting in high signal-to-noise ratios and short response times, typically of about 1 or 2 seconds (Ballangrud, 1993). This also means that long path lengths can be used, enabling accurate measurements of very low concentrations, even with weakly absorbing gases. Tunable Diode Lasers provide all the advantages of other semiconductor devices: they are small, solid-state devices, operate at room temperature, and have long-term reliability (over 15 years). Currently, they can be obtained for any wavelength throughout the NIR (700nm to 2000nm). Because many gases absorb in the NIR, the technique is widely applicable."

Jan 1, 2011

By Tim Edwards, Richard Triglavcanin, Ian Arbuthnot, Darren Colwell, Brad Garraway, Ken Roberts

"In the mineral processing industries, there is an increasing need to design thickeners which are able to produce high density underflows usually referred to as “paste”.The behaviour of a flocculated suspension in compression needs to be well understood in order to arrive at a reliable thickener tank configuration (i.e. diameter, cone angle and depth) for a required paste result.As a suspension approaches paste consistency, it’s fluid characteristics change markedly. It develops a high yield stress, and may have an increased tendency to form agglomerates, which lead to a phenomenon known as “rotating beds”, “donuts”, or “islands”. These characteristics present challenges to the designer of the rake mechanism.The subject paper addresses the requirements for designing a paste thickener, covering the following topics:o Testwork for thickener sizingo Design of rake mechanismso Suspension rheology and effect on designo Case studiesTESTWORK AND SIZING FOR PASTE THICKENERSThickening slurries to the maximum possible density (paste) is becoming increasingly common. Applications such as Autoclave feed thickeners, paste backfill and some counter current washing (CCD) circuits are all examples of potential paste thickening applications. The principle of paste thickeners is that the compression zone is much deeper than on either high rate (HRT) or high compression (HCT) units; generally 3 metres or more. As the compression zone gets deeper, theunderflow density for a given flux rate (tph/m2) increases, as a result of two factors:1. Longer bed settling time. Settling flocs move relative to one another and release interstitial fluid when they are in compression. Increasing bed residence time achieves higher density underflow as more fluid is removed.2. The nett weight of the bed creates a compressive force on the settling flocs. This force increases with depth, so that the flocs at the bottom of the bed experience the highest compressive force. This represents the driving force to expel interstitial fluid and hence increase bed density."

Jan 1, 2005

By M. R. Saharan

A brief overview of rockburst control measures is presented. The paper then elaborates on one key rockburst control measure, which is known as destress blasting. A historical background of the technique is presented in order to understand different aspects of its field application. The publication enumerates key aspects of the technique as being used in practice in South Africa and North America. The paper also presents an analysis of three case studies in order to demonstrate difficulties associated with the field application of distress blasting in hard rock mines.

Jan 1, 2006

By Tatiana Ravani von Ow, Leandro Bomvisinho

"The size of mills driven by ring-gear or by a gearless solution has significantly increased in the last years. This has created additional challenges for the driven equipment. The requirements for the mechanical devices and the power grid have become more demanding. Controlled soft starting and operation, especially in dual pinion mills, as well as the protection of the equipment has gained importance. The selection of the drive solution for the mill therefore becomes more critical. Besides the classical criteria such as performance, efficiency and capital costs other factors come in the evaluation of the system such as flexibility and optimization of operation, reliability and the ageing of the grinding equipment.Variable speed solutions offer significant advantages over conventional fixed speed drives due to their application specific features and process optimization capabilities, even for ball mills where these are not seen yet as a must.The initial capital costs are higher than some of the direct on-line solutions however the benefits for the operation during the lifetime of the mill generated by the use of converter solutions justify the additional higher investment.INTRODUCTIONThe method of powering mills such as AG, SAG and Ball has a long and technically interesting history. It can be said; almost every decade in the last half century had its own trend. The trend was dominated by the market demand, by the process development and requirement of the mechanical and the electrical technology but mostly by the price of the applied technology.All has started about 50 years ago with mill diameters less than 20 feet driven by fix speed synchronous or wound rotor motors with the power of about 2 MW. Around 10 years later, the mill sizes increased, but the necessary torque could not be transmitted by one pinion therefore dual pinion solutions were developed to power the mills. However, realization of the dual pinion solution was only possible when load could be evenly shared between the two pinions."

Jan 1, 2010

By P. Botane, A. Cailleau

"Compagnie Miniere Esperance operates a gold primary ore body. The ore is processed through crushing, grinding and gravity concentration generating tailings with remaining fine gold. Analyses of the tailings proved a residual gold grade sufficient for a chemical treatment.As lab tests proved the technical feasibility of a pre-concentration using flotation, an on-site pilot operation has been carried out to assess the continuous circuit performances, define the best configuration and obtain enough data for the industrial circuit sizing.Data collected during the pilot campaign have been used for calibrating a process simulator built with the USIM™ PAC software. The simulator validated the feasibility of upgrading the existing plant, including the reprocessing of tailings to obtain a good fine gold recovery in a small amount of concentrate. A preliminary capital cost has been achieved to assess the flotation workshop profitability.INTRODUCTIONCompagnie Miniere Esperance (CME), a mining company based in French Guyana, operates a gold primary ore body in open pit. The ore is processed through crushing, grinding and gravity separation in two stages: a top plant and a bottom plant. A “coarse” pond contains tailings of the top plant; this product feeds the bottom plant. Tailings of the bottom plant are stored in the “fine” pond.Analyses of the fine ponds proved a residual gold grade sufficient for a chemical treatment. However, direct cyanidation would require a too large installation, regarding the local conditions (accessibility, supplying and meteorological conditions).It has been then decided to test the feasibility of a pre-concentration using flotation. Lab tests have been carried out by SGS Lakefield (Canada) in March 2007, which proves the technical feasibility."

Jan 1, 2009

By Denis Labrie

Le minage en profondeur sous contrainte modérée à élevée présente de nombreux défis aux opérateurs et aux ingénieurs de mine notamment au niveau du contrôle de terrain et de l?environnement minier souterrain, pour assurer la sécurité des travailleurs sous terre et la continuité du cycle d?opération. Des conditions de contrainte élevée signifient une pression accrue au front de taille et sur les structures minières tels les piliers de mine et les fins de zone, un risque de rupture violente ou de coup de toit plus élevé, des zones de rupture plus grandes au pourtour des excavations, des charges accrues sur le support de terrain, etc. Le présent article fournit un aperçu du travail fait à l?intérieur du Programme de Contrôle de terrain de CANMET au cours des sept (7) dernières années, entre 1995 et 2001, pour comprendre et suivre l?évolution des niveaux de contrainte à l?intérieur des structures minières. Les propriétés déterminées en laboratoire sur des échantillons rocheux et les prévisions effectuées au moment de la conception sont comparées avec les observations effectuées en chantier à la paroi des excavations et à l?intérieur de la masse rocheuse. La plupart des cas discutés ici montrent une corrélation satisfaisante entre les observations effectuées en chantier d?une part, et les résultats d?essai obtenus en laboratoire et les calculs réalisés lors de la conception d?autre part. Ces observations peuvent donc être considérées comme des moyens relativement sûrs pour vérifier et suivre l?évolution des niveaux de contrainte présents à l?intérieur des structures minières.

May 1, 2002

By Don Peel

Mineral aggregate, the most widely used mineral resource globally, has attracted little academic or public interest. Of all mining developments, the aggregate resource is seldom factored into resource management decisions. This lack of recognition to the strategic aggregate resource has significant economic, environmental, and social implications. Impact to the economics, the environment, and the community coincide with the key elements of the United Nations concept of ?sustainable development?. To build on the concept, the mining sector contracted the International Institute for Environment and Development to assess how mining activity contributes to sustainability. As a result, a useful assessment process was developed by the Mining, Minerals and Sustainable Development (MMSD) Task Group entitled ?Seven Questions to Sustainability: How to Assess the Contribution of Mining and Mineral Activities.? In Alberta, recent opposition to mineral resource development by community residents offers an opportunity to employ the MMSD?s assessment procedure. The public opposition to the mining activity was addressed through a stakeholder planning process initiated by the municipal council of Sturgeon County, Alberta. As a result the Calahoo/Villeneuve Area Structure Plan (CASP) was formulated and adopted. To measure the effectiveness of the CASP planning process in terms of sustainability, this paper applies the MMSD?s Seven Question assessment to the Calahoo/Villeneuve Area Structure Plan.

May 1, 2004