Search Documents

By J. Jin, J. D. Miller

"Bubble attachment at hydrophobic surfaces is of critical importance in the flotation recovery of mineral resources and fundamental experimental results have been reported in the literature describing the details of film thinning, rupture, and displacement. Now, for the first time, bubble attachment phenomena are examined using Molecular Dynamics Simulations (MDS). The simulation involves a nitrogen bubble containing 906 nitrogen molecules in a water phase with 74,000 water molecules at the hydrophobic molybdenite (001) surface. During the simulation period of 1 ns, film rupture occurs and the nitrogen bubble attaches to the molybdenite (001) surface, resulting in a contact angle of about 90o. In contrast, the film is stable at the hydrophilic quartz (001) surface and the bubble does not attach. Contact angles, determined from MD simulation after stabilization of the three phase line of contact, are reported and these results agree well with experimental and MDS sessile drop results. In this way, film stability and bubble attachment are described with respect to interfacial water structure for surfaces of different polarity. For example, the interfacial water molecules for the hydrophobic molybdenite (001) surface have relatively weak interactions with the surface when compared to the hydrophilic quartz (001) surface, as revealed bythe presence of a 3 A water exclusion zone at the molybdenite/water interface. INTRODUCTIONAttachment of air bubbles to mineral particles is of fundamental importance in understanding flotation separation phenomena. It is well known that attachment of an air bubble at a hydrophobic surface includes film thinning, film rupture, and film displacement (Somasundaran, 2006; Wilson, Adlard, Cooke, & Poole, 2000). Experimental techniques, such as high speed video, can catch the process of bubble attachment at a mineral surface (Drelich & Miller, 2012; Niecikowska, Krasowska, Ralston, & Malysa, 2012). However, molecular scale information to examine the phenomena has not yet been reported."

Jan 1, 2016

By M. A. Clayton, D. Kinakin

The Mitchell Creek Landslide is a large, structurally controlled, complex bedrock instability located in northwestern British Columbia. Characterization of the landslide using aerial photograph, exploration geology, and geotechnical investigation data has been completed allowing the development of a three dimensional conceptual model of the landslide domains and slope behaviour. Three domains have been identified in the landslide, from top to bottom: the Sliding domain, a relatively intact slab slowly sliding into the valley; the Transition domain, located in the mid slope of the landslide and showing evidence of significant extension and continuing to subside and displace into the valley; and a Toppling domain, at the toe of the landslide in an area of overturned foliation. Movement is greatest in the Toppling domain, with long term estimated rates of movement up to 4 times that of the Sliding domain; the Transition domain exhibits the greatest range of displacement rates, with average long term values approximately double the slower Sliding domain. This paper documents the results of numerical modelling of the Mitchell Creek Landslide with variation in geomechanical properties, basal rupture surface configuration, structural fabric, and pore water pressure conditions. The locations of internal shear surfaces within the landslide have been estimated from surface scarps, structural fabric orientation, and borehole monitoring data. The performance of each numerical model was evaluated against observed behaviour of the landslide. The configuration and properties of the basal rupture surface were identified as critical to model behaviour, as was spacing and location of internal structures.

Jan 1, 2015

By A. Quilodran, B. Jakovljevic, T. McCallum, P. Wong

"Rare earth separation by solvent extraction (SX) requires multiple separation plants each consisting of many extract, scrub, and strip stages to separate the individual metals. SX modeling advances have brought benefits to circuit design and process optimization by quickly narrowing test conditions without the need for exhaustive laboratory studies. Modeling can be used to optimize circuit configuration, O/A ratios, and acidities, which allows for CAPEX and OPEX savings. A comparison between pilot plant data and the results expected from modeling is presented for rare earth separations with CYANEX® 572.INTRODUCTIONRare earth separations can be difficult due to limited separation between the elements (Xie, Zhang, Dreisinger, & Doyle, 2014). This requires relatively complex solvent extraction circuits utilizing multiple extract, scrub, and strip stages as well as multiple SX configurations to achieve the desired metal purities. Designing rare earth circuits can be complex, and significant time and testing may be necessary to determine the required staging and optimal conditions.Circuit modeling for rare earth separations has been introduced to the industry using CYANEX® 572 extractant (Soderstrom, McCallum, Jakovljevic, & Quilodran, 2014). CYANEX® 572 is an acidic organophosphorus extractant formulation which has a weaker ligand-metal complex strength than that of the traditionally used phosphonic acid extractants. This allows efficient extraction while requiring a significantly lower acid concentration for stripping (Wang, Li, Zhao, Dong, & Sun, 2015). The reduced acid requirement in strip is expected to provide OPEX savings.The modeling can be utilized to quickly determine the required acidity and organic/aqueous (O/A) ratio for a given separation. It is also expected to reduce CAPEX requirements as optimal staging can be determined, and implemented.CYANEX® 572, combined with modeling, was utilized to produce a purified dysprosium (Dy) stream. To achieve this separation, multiple SX circuits were designed and operational conditions specified to separate Dy from the mixed rare earth chloride feed."

Jan 1, 2016

By James Kear, Romain Prioul, Robert G. Jeffrey, Andrew P. Bunger, Dimitry Chuprakov

"Unconventional gas and geothermal reservoirs are typically naturally fractured and therefore the challenging problem of hydraulic fracture (HF) growth through naturally fractured rocks is an important issue especially for the development of accurate predictive HF models. This paper presents results from laboratory experiments in which HFs have been created in both sandstone and crystalline (gabbronorite) rock specimens such that they impinge either orthogonally or at an oblique angle on an unbonded, machined frictional interface. Depending on the conditions of each experiment, the fractures either cross or are blunted at the interface. The growth behavior was ascertained for these experiments based on a synthesis of the injection pressure record, active ultrasound monitoring, and direct post-experiment inspection of fractured specimens. From these experiments we observe: 1) A contrast between direct crossing and crossing with an offset for orthogonal and oblique intersection, respectively, 2) Apparent independence of crossing/blunting behavior on the friction coefficient for orthogonal intersection, 3) Dependence of the stresses required to promote crossing on the intersection angle between the HF and NF, 4) Existence of cases in which the hydraulic fracture crosses but then essentially ceases propagation such that all fluid is diverted to the interface. INTRODUCTIONHydraulic fracturing is a vital technology used to increase the productivity of oil, gas, and geothermal wells. Predicting hydraulic fracture (HF) growth is, in turn, critical to design of hydraulic fractures that grow to the desired length, accept the desired amount of proppant, and remain contained in the reservoir without unwanted height growth into surrounding layers (e.g. Economides and Nolte, 2000). The importance of HF modeling has prompted 6 decades of research during which simulators have become more efficient, more accurate, and have addressed a growing range of complexities (see review of e.g. Adachi et al., 2007).One of these complexities is the interaction between HFs and mechanical discontinuities such as natural fractures (NFs). Efforts in this area have been mainly driven by development of unconventional (i.e. low permeability) oil and gas resources because essentially all viable low permeability reservoirs, including shale gas/oil reservoirs, are naturally fractured to some degree (King, 2010). One of the most important questions for developing effective HF stimulation strategies in these reservoirs is whether the hydraulic fracture(s) is/are expected to be single-stranded or whether interaction with the NFs will lead to network-like growth. The basic building block for numerical simulators that can address this question (such as Kresse et al., 2013 and Weng et al., 2014) is whether an HF that intersects an NF will cross the NF or whether its growth will be captured by the NF so that additional fluid injection pressurizes the NF but does not generate ongoing growth of a new HF. These scenarios, including subcategories such as crossing with an offset, have been recognized for several decades (Daneshy, 1974; Warpinski and Teufel, 1987, and as recently reviewed and expanded by Chuprakov et al., 2013)."

Jan 1, 2015

By Marcelle A. Hauseux

"The Turgeon Lake granite lies 5 miles north of Baie Johan Beetz, Quebec, at the eastern margin of the Grenville Province. The rocks are classed as granites, granulites, quartzites, biotite schists and gneisses, and amphibolites. The granite's uraniferous character is manifested by phosphuranylite, uraninite, and metamict .zircons associated with magnetite. Field anomalies occur in irregular pods, conformable with the tectonic foliation, in bands roughly paralleling sedimentary bedding. Associated features diagnostic of uraniferous granite are smoky quartz, brick-red feldspar, magnetite and a coarse to pegmatitic grain size. The granite is chemically and physically heterogeneous. Metasediment-granite contacts are diffuse or sharp, and usually conformable to bedding. The regional foliations within all rock types are coherent, and sedimentary structures are often preserved within both metasediments and granite. Autometasomatism probably was a strong granitization agent.A uranium reconcentration into fold-axial zones from original sediments which have been highly granitized during at least two phases of folding is suggested from the available data."

Jan 1, 1977

By A. Mosqueda Martinez, L. C. Trytten, R. P. Kofluk, J. J. Budac

The Corefco ammonia leach nickel refinery treats Ni-Co mixed sulphides from the high-pressure acid leaching of Moa Bay nickel laterite. Due to the low iron content of the feed, the ammonia leach process generates a leach residue with ~10% Ni+Co. Since commissioning a leach residue pressure filtration circuit in 2002, this residue has been stockpiled, dried, and sold commercially. For several years, the residue was sold to nickel smelters overseas. In 2014, re-processing of the residue in the high-pressure acid leach was tested. Lab test work was completed showing excellent extraction of the contained nickel and cobalt, and additional beneficial effects in the high-pressure acid leach circuit. A plant test in Moa confirmed the results, and preparation for shipment of the valuable leach residue for re-processing has begun. This paper outlines the test work and results, and some commercial considerations.

Jan 1, 2015

By L. T. Pasiechnyk

After a brief review of the various hydrocarbon storage methods currently being utilized and statistics on underground hydrocarbon storage, this paper will briefly describe the technology involved in solution mining salt to create caverns of engineered shape and size and briefly discuss the economical and environmental advantages of hydrocarbon storage in solution-mined salt caverns. Other possible uses of salt caverns will be mentioned.

Jan 1, 1978

By C. Stapel, P. D. Roberts, D. G. Jones, W. G. Macdonald, R. J. De Meijer

"Abstract-Measurement of natural radioactivity has been used in both a qualitative and a quantitative way in mineral exploration, particularly in the search for uranium. In the last five years, the Kernfysisch Versneller Instituut (KVI) and British Geological Survey (BGS) have designed, built and tested a new detector system that greatly improves quantitative applications in mineral exploration, especially on the seafloor and in the nearshore zone. The new system is an enhancement of an earlier BGS design. The major improvements comprise the use of a highly sensitive ?-ray detector, together with new data processing, from which concentrations of natural radionuclides may be deduced in real time. After laboratory analysis of samples, these concentrations can be converted into mineral percentages. Once the mineralogy of an area has been characterized, this conversion can also be done in real time.Thus far the system has mainly been used to map heavy-mineral concentrations in coastal subtidaland intertidal sediments. For such work the multi-sensor detector probe is towed on the seafloor and various parameters are recorded continuously. The probe contains, in addition to the gamma-ray detector, a water-pressure sensor (giving water depth) and an acoustic device to measure bottom roughness. The system, when used together with high-precision positioning systems such as D-GPS, enables the production of detailed maps of bathymetry, bottom roughness, and seafloor radioactivity or mineral distribution. These maps allow mineral concentrations to be readily correlated with seabed topography and sediment type. In the same way, ?-ray detectors could be used advantageously during dredging operations to provide on-line assessment of the mineral content of the dredged sediment as well as to guide the direction of dredging. Additionally, the same technique could be used to monitor the subsequent fate of a dredge spoil after dumping on the seafloor.Natural radioactivity arising from potassium and the thorium and uranium decay series has potential use for the fast and reliable assessment of siliciclastic and phosphatic impurities in limestones. Detection of such impurities may preclude the use of the limestone for chemical or cement production.Apart from its use in exploration, the technique has significant potential in mineral processing, particularly of heavy minerals. It can be applied as on-line quality control in dry and wet separation processes and for process control, by using decisions based on the results to control valves and other instrumentation. In addition, it can also be used in environmental monitoring of waste arising from mineral extraction and processing. In conclusion, the technique described has a diversity of applications in exploration, mining and mineral processing."

Jan 1, 1997

By A. R. Chambers

Malagash received its name from the Indians many years ago on acco.unt of its turbid (milky) waters, although,' the red men did not appreciate the significance of this turbidity, and were, of course, entirely ignorant of the crystal beds of pure salt that lay beneath their feet. The salt lake of the Mississippian, or Lower Carboniferous period, in which these beds occur, was apparently a large one, for there is evidence of its existence at intervals all the way from Sydney, Cape Breton, to St. John, New Brunswick, 300 miles as the crow flies, and there is no knowing what its other dimensions may have been, as much of this horizon is now buried on the one side beneath the waters of the Gulf of St. Lawrence, and on the other underneath the Atlantic ocean. About midway of the area and underlying the counties of Colchester and Cumberland, there occurs a synclinal basin of which the Malagash salt outcrop forms only a small portion of its northern limit. This basin has been described very fully by A. C. Hayes. (1) The operations carried on at Malagash since Hayes wrote his report have brought to light very little in the way of new geological data, except to confirm his pre-dictions as to the probable faulting of the salt strata, and the effect which these faults would have on mining operations.

Jan 1, 1924

By J. Shanks

A S far back as 1925, Brazeau Collieries, Limited, became interested in .briquetting. This was brought about by complaints from their principal customer that stack losses, due to a high percentage of fine coal in their mine run, were excessive. The Company considered oil spraying of the fines. This, after some experiments and tests had been made, was ruled out as uneconomical and impracticable. When sufficient oil to be effective was put into the fines, it caused the coal in the tender of stoker-fired engines t0 arch over the screw feeder. The Company ultimately placed their problem in the hands of the Re-search Department of the University of Alberta. Experimental work was carried on by this department over a period of more than a year. The results obtained and the experience gained in this research work were conveyed to Brazeau Collieries in a report dated October 31st, 1929, and in a supplementary report dated February 2nd, 1935. Most of the results obtained in experimenting with Brazeau coal are embodied in a brochure, reprinted from the proceedings of the Second International Conference on Bituminous Coal, Vol. 19-24-28, entitled Principles in the Briquetting of Coking and Non-Coking Bituminous Coals, by E. Stansfield and W. A. Lang. All who are interested in briquetting should read this brochure. In the writer's opinion, iris the most important treatise on the subject printed in recent years. The results given in the paper are, of course, those obtained in laboratory investigation. It was pointed out to the writer that it would be most interesting to have such results correlated with those obtained in commercial practice. In this short paper, an attempt is made to do so.

Jan 1, 1942

By M. Board, R. Pakalnis, S. Seldon, R. Brummer

The Kidd operation mines roughly 10 000 tpd of copper and zinc ore from underground and employs about 700 personnel. In the late summer and fall of 1997, major movements in the proximity of the east wall of the Kidd open pit had been observed. The Kidd pit had been mined from 1965 to 1977 to depths of 260 m (850 ft), followed by subsequent mining by underground methods to current depths in excess of 1830 m (6800 ft). The No. 1 Mine (2600 Level to pit bottom) is approximately 90% extracted, with most of the remaining reserve between 2000 and 2500 levels. Although initial concerns centred on the stability of the pit walls, the potential ramifications of the movements to the underground were recognized and measures were implemented to ensure the safety of personnel as well as to minimize the potential damage to existing operations. In late October, damage to underground operations was observed as deep as the 2000 Level. In the final assessment, the global mobilized mass was a “wedge”-shaped hangingwall block extending from surface to about 610 m (2000 ft) below surface. The “wedge” boundaries are defined by a fault and shear zone which have continuous lengths in excess of 1070 m (3500 ft); its base by shearing through the host rock mass; and its eastern face by deep tension cracks (Fig. 1). Mined and filled excavations at the western face of the “wedge” allowed mobilization of a mass in excess of 30 M tonnes. Movements in excess of 75 cm (30 in.) per day were recorded on the surface stations that preceded the complete shutdown of operations on October 29, 1997. The evaluations in the days following the shut-down were centred on mitigation of immediate and future possible negative impacts on infrastructure and mining of the remaining No. 1 Mine reserves while ensuring the safety of the operators. This effort required the rapid assessment of the potential damage of the block movement on underground infrastructure, stope access, drainage and ventilation, as well as airblast potential due to the falling of a large block into the pit near the ventilation intake at the base of the pit. These assessments were presented in a previous paper (Seldon et al., 1999). In total, the lateral movement of the block on the ground surface was over 4.3 m (14 ft). This paper describes the detailed studies performed to understand the failure mechanism and to assess the impacts on future mining in No. 1 Mine.

Jan 1, 2000

By D. A. Le, T. S. Nguyen

"In Canada and other countries, several types of rock formations are being considered for the geological disposal of radioactive wastes. In order to better understand the ability of these rocks to contain and isolate the wastes, the Canadian Nuclear Safety Commission collaborates with different international research organizations and has access to experimental data from Underground Research Laboratories (URLs) in the world. Such an URL is situated in Opalinus Clay, at Mont Terri, Switzerland. An experiment, consisting of the excavation of a tunnel followed by water and gas injections in a test section of the tunnel, was performed at the URL. The authors have developed a mathematical model, based on the poromechanics theoretical framework, to simulate those phases of the experiment. The constitutive relationship for the stress-strain behaviour of Opalinus Clay takes into account its inherent anisotropy due to bedding. The model was able to capture the main features of the experiment such as the prediction of the shape and extent of the excavation damage zone and its influence on water and gas migration.INTRODUCTIONIn Canada and many other countries, several types of rock formations such as crystalline rocks and sedimentary argillaceous rocks, are being studied for the disposal of used nuclear fuel from nuclear power plants. Geological disposal relies on multiple natural and engineered barriers for the long-term containment and isolation of the wastes. The host rock is a major natural barrier and is the subject of extensive research. The Canadian Nuclear Safety Commission (CNSC), Canada’s nuclear regulator, will be responsible for the licensing of future deep geological repositories. In order to evaluate the safety of deep geological repositories, CNSC staff keep abreast of scientific developments by collaborating with national and international partners on experimental and theoretical research on the long term performance of those engineered and natural barriers. Through that collaboration, the CNSC has access to data resulting from experiments performed at different Underground Research Laboratories (URLs)."

Jan 1, 2015

By B. van Beek, T. Goff, P. Gebski, P. Szyplinski, W. L. Ying

"Monitoring the refractory lining integrity is essential to assure the safety of the operators and to determine the remaining campaign life of a furnace. Early detection of refractory lining degradation is essential to avoid sudden furnace failures and prevent unscheduled shutdowns. In the mid-1990s a stress wave propagation technique was developed and since then it has been utilized by Hatch Non-Destructive Testing (NDT) Group to evaluate furnace linings. For the last 17 years the AU-E technique evolved in terms of hardware, software and signal acquisition and interpretation. Most importantly, based on more than a decade of commercial applications, an extensive database of various failure modes, refractory deterioration trends and material properties has been created. This knowledge base is an integral part of AU-E which progressed from a NDT technique towards a comprehensive approach for furnace condition monitoring. All of the improvements introduced over the last several years have greatly improved the accuracy of the measurements. The data analysis process has also become more time efficient making the critical results available to the furnace operators in a more timely manner. Today the AU-E technology is used on a variety of process vessels in non-ferrous, glass, chemical and iron and steel industries.In this paper we are reviewing the available techniques for furnace refractory lining measurement and discussing the pros and cons of each method. The need for continuous improvement and development of new techniques for refractory monitoring is also emphasized. Finally, we are presenting a number of case studies and comparisons between the physical verifications and the AU-E measurements."

Jan 1, 2015

By Fabio Terzi

In this investigation some preliminary results are reported about the electrochemical oxidation of CO using goldbased encapsulated nanoparticles grafted on conducting substrate. The investigation has been planned in four steps: 1. production of Au(111) substrate and modification with self assembled monolayers; 2. synthesis and embedding of nanoparticles; 3. grafting of encapsulated nanoparticles on electrode substrates; 4. investigation of CO electroxidation on the modified electrode. The systems were characterized by means of various techniques (spectroscopic, microscopic, and electrochemical methods), obtaining information about SAM's structure and morphology, size and composition of nanoparticles and electrochemical behavior of modified electrodes.

Oct 1, 2003

By J. Pepin

When using alternating current submerged arc welding (SAW) to produce pipes from microalloyed linepipe steels, it is critical to balance penetration depth and deposition rates, in order to minimize the number of weld passes while still maintaining good heat affected zone (HAZ) microstructures and properties. A series of bead-on-plate (BOP) submerged arc welds were performed on X70 steel, using different waveform variable settings (i.e., balance, offset and frequency). Weld bead cross-section profile deposition and penetration areas were measured, and both Vickers hardness and Charpy V-notch impact testing were performed. Both single electrode and tandem electrode welds were evaluated.

Jan 1, 2011

By M. H. Fathi

The aim of this work was to prepare the metallic coatings on 316L stainless steel dental implant and evaluate the corrosion characteristics and thus the biocompatibility of the uncoated and metallic coated dental implants and comparison of the effect of the type of coatings on biocompatibility. Three types of metallic coatings including Tantalum, Niobium, and Titanium coatings were made using physical vapor deposition process on 316L stainless steel dental implant. Structural characterization techniques including; X-ray Diffraction, Scanning Electron Microscopy and Energy Dispersive X-ray Analysis were utilized to investigate the microstructure and morphology of the coatings. Electrochemical potentiodynamic tests were performed in two types of physiological solutions at 37±1 °C in order to determine and compare the corrosion characteristics. All three types of metallic coatings had a positive effect on improvement of the corrosion behavior so that the coatings could increase the corrosion resistance of 316L stainless steel and this trend was independent to the type of physiological environment. Biocompatible metallic coatings could decrease the corrosion current density that is a distinct advantage for prevention of ion release. This can improve the biocompatibility of the implant and, consequently prevention of tissue damages, inflammation and irritation and obtained desirable histopathological response.

Jan 1, 2007

By Takayuki Takasugi, Naoya Masahashi, Yasuyuki Kaneno, Satoshi Semboshi, Yusuke Kadoi

Cu–Ti alloy wires doped with and without a small amount of Ni were fabricated by over-aging and using intense drawing procedures. For both the Cu–Ti alloys with and without Ni doping, the over- aged microstructure was occupied fully with a coarse lamella of Cu solid solution and β-Cu4Ti plates precipitated discontinuously by grain boundary reactions. The full-lamellar microstructure was developed much more rapidly by aging in multi steps at 873 K to 723 K rather than by isothermal aging at 723 K. Ni doping in Cu-Ti alloy was also effective to accelerate the formation of the lamellar microstructure. When drawing the over-aged alloy with inferior hardness but superior electrical conductivity, the strength increased steadily and eventually exceeded that for the wires drawn from the peak-aged alloy. In addition, the electrical conductivity of the wires drawn from the over-aged alloy was always much greater than that from the peak-aged alloy. Eventually, the procedure of over-aging, followed by intense drawing, could enhance both the strength and electrical conductivity of Cu-Ti alloys, whichever they contain a small amount of Ni or not, rather than the conventional peak-aging and drawing process. INTRODUCTION Cu-based alloy wires, which have an excellent combination of strength and electrical conductivity, have attracted extensive attention for highly mechanically stressed electrical devices, such as conductive lead wires and wires in suspension springs. Cu-Be alloys are widely used for such electrical components owing to their combination of strength and electrical conductivity among industrial Cu-based alloys. However, since beryllium is potentially toxic and also a rare element, substitute materials for Cu-Be alloys have been searched for several decades. Age-hardenable Cu–Ti based alloys have been proposed as candidates because their mechanical and physical properties are comparable to those of Cu-Be alloys; however, their electrical conductivity is inferior (Datta & Soffa, 1976; Soffa & Laughlin, 2004). In order to satisfy the requirement of downsizing and streamlining electrical devices, further improvement of the mechanical and electrical properties of Cu–Ti alloy wires is needed. Age-hardenable Cu–Ti alloys, which contain approximately 3 to 6 at.% Ti, are typically prepared using a solid solution treatment above 1100 K and then aging at a moderate temperature of 700 K to 800 K. It has been revealed that the microstructural events during aging progress as follows (Soffa & Laughlin, 2004): (1) compositional modulation of the parent supersaturated Cu solid solution in an initial aging stage (Laughlin & Cahn, 1975), (2) continuous nucleation and growth of fine needle-shaped precipitates of metastable β’-Cu4Ti with a tetragonal structure in a peak-aged stage, and (3) discontinuous precipitation of cellular components laminating the plates of a terminal Cu solid solution and stable β-Cu4Ti with an orthorhombic structure at the grain boundaries in an over-aging stage. It has been also accepted that the highest number density of dispersed fine β’-Cu4Ti needles should contribute to maximal strengthening. On the other hand, decease of the strength in the over-aging stage occurs due to the replacement of the fine β’- Cu4Ti needles with cellular components containing coarse β-Cu4Ti plates, while the electrical conductivity is significantly enhanced due to the depletion of solute Ti in the Cu matrix. This suggests that a combination of strength and electrical conductivity for age-hardenable Cu-Ti alloys is in a trade-off relationship, and that innovative improvement of both properties might be limited to tuning the aging conditions.

Jan 1, 2019

By L. Shang

In conventional continuous hot rolling processes, metals are usually reheated to a temperature such that the workpiece will maintain appropriate hot working characteristics as it proceeds through the rolling mill, assuming that the temperature is continually decreasing. Metallurgically, reheating will reduce micro-segregation in the as-cast material, may increase the as-cast grain size and will affect any second phase particles present in the as-cast structure. All these changes can affect the hot working characteristics, and the final as-hot rolled microstructure. In order to study the effect of reheating on AZ31 magnesium alloy, a plate sample was cast in a water cooled copper mould and a series of compression tests was performed at a temperature of 350 °C, strain rate 0.01 5-1, and strains from 0.2 to 1.0, after different reheating schedules. It was found that there is no significant difference in flow behavior between the as-cast sample and all but one of the reheated ones. The reheat treatment of the 'anomalous' sample was a two stage heat treatment; it was first reheated to 450 °C, cooled to room temperature, then reheated to 350 °C. The effect on the flow curve was to increase the flow stress. This result may be related to changes in second phase particle characteristics.

Jan 1, 2006

By D. Michaud, C. Bazin, S. Lévesque, L. Pérez-Barnuevo, H. Longuepée

In recent years, with the emergence of Geometallurgy, a great effort has been made to characterize ore resources as early and accurately as possible, to allow better design and a more efficient operation of mineral processing circuits. In this context, core logging plays an important role, since drill cores provide the first insight into the ore characteristics. However, to satisfy geometallurgical requirements, traditional core logging does not suffice. New tools and methodologies need to be developed for the automation of core logging and the acquisition of mineralogical data better related to mineral processing performances. In this paper, a methodology for the geometallurgical characterization of drill cores is proposed, based on the drill core textural patterns. Textural pattern is defined here as the macroscopic spatial arrangement of minerals. The Mont-Wright iron ore deposit (Quebec, Canada) is used as a case study. The first part of this work aimed at analyzing the potential link between the iron ores textural patterns observed in drill cores and their response to ore processing, namely comminution and concentration. Preliminary results show similar performances in terms of energy consumption and heavy liquid separation for samples showing the same textural pattern. In the second part, this work seeks to develop a methodology for the automated identification of drill core textural patterns by the application of digital image analysis and discriminant function analysis. The results obtained show that this methodology is able to discriminate between the textural patterns identified at Mont-Wright with a good rate of success. Therefore, this work lays the foundation for the development of a new drill core characterization tool, which would allow for the early prediction of the iron ore behaviour during mineral processing through the identification of drill core textural patterns.

Jan 1, 2016

By A. O. Dufresne

Introductory At the Annual Meeting of the Institute, held two years ago, I had the privilege of presenting a paper on Recent Mineral Discoveries in Western Quebec. In it were pointed out the areas favourable for prospecting in that section of Quebec adjoining the mining camps of northern Ontario; the discoveries that ?had been made were recorded; and some of the developments up to that date were reviewed. Since then, two full years have elapsed, during which a considerable amount of serious work has been performed with such results that western Quebec has today six properties about ready to mine commercial ores of gold, copper, and zinc. These results have been brought about after large sums of money had been invested to bring the district to a producing stage. A smelter has been built, and is already producing copper; two railways have extended their lines into Rouyn; and the Provincial Government has shown faith in the future of the district and has spent large sums of money in the building of highways and for other public works. The purpose of the present paper is to review the developments of the last two years, and the work that has been performed in various spheres of activity in that section on western Quebec covering the county of Abitibi and the northern part of the county of Temiscamingue.

Jan 1, 1928