Search Documents

By M. J. Gole, R. E. T. Hill, S. J. Barnes

"The Agnew (also known as the Perseverance) nickel deposit and its northern extension, the Rocky's Reward deposit, form one of the world's largest accumulations of nickel sulphides hosted by komatiites. Agnew was previously classified as an ""intrusive dunite-associated"" deposit . It has now been shown that the sulphides are hosted by komatiite flows which underlie an adcumulate-textured dunite body that crystallized in a large lava channel.The rocks of the mine area have been subjected to a metamorphic temperature of550°C and pressure of up to 3 kb. The komatiites have mostly been reconstituted to olivine-amphibole chlorite assemblages. There is a zoned sequence of enstatite-, anthophylite-, talc- and antigorite-bearing assemblages inwards from the western margin of the ultramatic reflecting variations in the CO/HP ratio of metamorphic fluids.Facing directions are determined from variations in the proportions of metamorphic minerals and in rock compositions which reflect asymmetric layering in the flows . Olivine-sulphides matrix ore is hosted in a single 50 m thick, east-facing flow that is overlain by flows containing massive sulphides. Much of the massive sulphide has been physically remobilized into fold noses, faults and shear zones. Chemical diffusion of ore components has upgraded a sulphide-rich metasedimentary unit where it is in structural contact with massive ore.To the north, the mineralized flow sequence is separated from a stratigraphically higher komatiite sequence, the Perseverance ultramafic complex, by approximately 150 m of felsic meta volcanic and meta sedimentary rocks. Southward, the Perseverance ultramafic grades laterally into an olivine adcumulate body and its lower contact cuts progressively down stratigraphy until it lies directly on top of olivine-sulphide ore of the mineralized flow sequence. This discordant contact is interpreted as the base of a thermal erosion channel formed by a voluminous komatiite lava flow. This contact greatly influenced later deformation of the mineralized flow sequence."

Jan 1, 1989

By A. J. Paul Laprairie

The process for which it is to be used is too often the only consideration in the design of a vessel. A de-sign allowing for practical manufacture and erection, as well as for proper maintenance, can often give over-all economies. Most platework in-stalled today is of welded construction. Therefore, metallurgical control is important in its manufacture. Also, because many concentrating and re-fining processes tend to be corrosive, the subject of protective coatings as a part of the manufacturing process is extremely important. The plant de-signer should know how to evaluate and specify controls for the metallurgy and for the coatings. Mining operations are becoming more sophisticated in the field of mechanical engineering. More and more emphasis is being given to preventive maintenance. The first step in any maintenance program, however, is good inspection service. This paper will suggest methods for the inspection of platework, and outline methods for repair and replacement.

Jan 1, 1963

By W J. Dyck

Past attempts to establish an integrated steel industry on the West Coast of Canada have been unsuccessful for at least three reasons: (a) insufficient reserves of a suit-able iron ore supply; (b) a relatively small local market for iron and steel; and (c) the non-availability of an economical process to produce primary iron on a small scale. Today, the reserves of economically mineable ore deposits are ample to support a steel production of 100,000 to 200,-000 tons per annum. The local market has increased so as to be able to absorb most of this capacity. With-in the next few years, a small integrated steel plant, including the "H-Iron" direct iron ore reduction process for electric furnace charge stock production, will be able to show a profitable operation. Introduction

Jan 1, 1963

By F. H. Wheeler

CONSIDERING the nature of this audience, I perhaps, in addressing you on the subject of air transportation as related to the mining industry, should speak with tongue in check or at least with some reservation. I know full well that many of you, veterans in the great mineral development in Canada, are perhaps more conversant with the overall aviation picture than I, for aviation to you has been the means to an end, and in many instances has been part and ?parcel in the success of your particular projects, in the form of the initial means of transport. I feel, however, that we in this room today have somewhat parallel geographic interests - yours in relation to what is in the ground, mine in the air - and also in the forests and in the streams - aviation, hunting, and fishing - things which have occupied my attention practically all my adult years. In the light of what has gone. before, and in view of present developments, I think you will agree with me when I say that I do not think there could be a more intriguing pursuit than playing a hand in rolling back Canada's tremendous northern frontiers, even if, at this stage, we have made but slight impression on the untold opportunities which lie in our wide-spread, undeveloped areas.

Jan 1, 1956

By W. A. Jankola

Teck Cominco Metals Ltd. operates an integrated zinc-lead smelter at Trail, British Columbia, Canada. The zinc circuit comprises three parallel operations: conventional fluid-bed roasting, direct zinc pressure leaching of concentrates and atmospheric leaching of zinc oxide fume recycled from the lead smelter. The products from these three areas are combined in the main leaching plant where they undergo iron purification. Unlike most leaching circuits, the leach process in Trail begins with an acid leach and is followed by a neutral leach. An evaluation was undertaken to determine if the process at Trail could be improved by converting to the conventional neutral leaching process with a subsequent acid leach of the residues. This paper explores the results of these tests and the implications for Trail Operations.

Jan 1, 2006

By Richard W. Hutchinson, Robert W. Hodder

"Pyritic massive sulphide deposits lie conformably above submarine volcanic rocks, and beneath siliceous and manganiferous iron formations. The massive bodies are often zoned, with a barren pyritic top grading downward into pyrite with sphalerite, and occasionally galena, and a chalcopyrite-rich base. They are frequently brecciated, like the lavas beneath them, which contain pyrite and chalcopyrite as coatings on joints and fractures and as dispersed grains. The lavas also exhibit propylitic, argillic and silicic alteration. These sulphide deposits appear to have formed on sea bottom from fluids escaping through the lavas during periods of exhalative and sometimes explosive volcanism. The process may be comparable to the present deposition of base metals from hot brines in the Red Sea. Some porphyry copper deposits resemble the altered, sulphide-impregnated lavas which lie beneath bodies of pyritic massive sulphide. In porphyry copper deposits, pyrite and chalcopyrite occur as veinlets and dispersed grains in intensely fractured tuffs, flows, sub-volcanic intrusions or other host rocks, characterized by propylitic, argillic and silicic alteration. Metal zoning is present; sphalerite and galena often occur in manganiferous veins peripheral to a shell of pyritic veinlets which encloses the mineable zone of chalcopyrite-bearing veinlets. This sulphide distribution appears to have formed from hydrothermal fluids escaping, either passively or violently, from solidifying magma. The fluids may be comparable to hot brines encountered by drilling in the Salton Sea area of California.There are also important differences between massive sulphide and porphyry copper deposits. The former usually occur in differentiated, mafic-to-felsic subaqueous volcanic rocks, whereas porphyry copper deposits are often associated with shallow plutons and subaerial volcanic rocks of intermediate to felsic composition. Calcic-sodic metasomatism accompanies the massive sulphides, whereas potassic metasomatism characterizes the porphyry cop.per deposits. Further, ages of massive sulphides range from Archean (Keewatin) to Tertiary, but porphyry coppers are Triassic to Tertiary in age. These similarities and differences suggest that massive sulphide and porphyry copper deposits are related tectonically and metallogenetically. The former were generated during early stages of crustal evolution, particularly in Archean time, and were repeatedly derived during early stages of younger, individual tectonic cycles. In contrast, the porphyry coppers developed during the later stages of crustal evolution - later in terms of both absolute age and relative age within younger individual tectonic cycles. They appear in younger rocks generally, and specifically in rocks involved in events of the middle and late tectonic stages of orogenic belts. The massive sulphide deposits are of early-magmatic eugeosynclinal affiliation, whereas the porphyry deposits formed in late-magmatic, predominantly subvolcanic settings at the edge of continental plates, where contemporaneous exhalative volcanism was mainly a subaerial phenomenon. Transitional types of deposits exist and are found on continental margins with flanking eugeosynclinal sequences."

Jan 1, 1972

By J M. Fletcher

The responsibility and scope of the Industrial Engineering Department, as organized at the Jeffrey mine, has been broadened to include any study, project or report that could result in more effective use of men, materials and equipment. Although still emphasizing wage incentives and co t reduction, much more varied work is now done, consistent with the in-.creased complexity of industry. Additional activities now include production, maintenance and inventory control improved job evaluation, packaging, labour utilization studies, technical sales liaison, mining, milling and service department n1ethods, plant layout, and specialized project analysis. Additional techniques include the extensive use of work .sampling and standard data. A recent trend has been toward increased emphasis on industrial relations, both in introducing change to the men and in providing requested explanations to Union stewards and officers. These new responsibilities have resulted in the development of specialists in some rather narrow industrial engineering fields, as well as the necessity for industrial engineering assistance in supervisory and job training.

Jan 1, 1963

By A. Romero

"Most underground mines require heating or cooling systems to meet health and safety standards in the working areas. In regions where daily or seasonal fluctuations of environmental conditions exist, these systems tend to be over-sized and operate at low average load factors, which increase both investment and operating costs. One possible approach to reduce the temperature variations of the fresh air supplied to the mine, and so reducing the investment in large heating or cooling systems, is to use rock as a thermal regenerator or thermal storage system. Packed rock beds act as thermal inertial units, damping the atmospheric temperature oscillations to provide a more constant fresh air temperature. However, although regenerators exist in some mines, and packed bed rocks have been studied in detail in solar thermal power applications, there is a lack of tools to design new and sufficiently large storage systems of this kind. This work fills the existing gap by presenting a methodology to design and evaluate the impact on the ventilation systems of these regenerators. The method is validated using existing rock bed systems found in the literature and illustrates possible designs for small and large size regenerators in both hot and cold climates.1 INTRODUCTION “ It is quite amazing how often answers to extremely complicated problems can be obtained in this way, by using greatly simplified models of the real situation for the purpose of calculation.” Whiller, A. in private communication to J. S. Stachulak (1989). Motivation Most underground mines located in regions with extreme climatic conditions require the thermal pre-treatment of the fresh ventilation airflows, whether for heating or cooling. Heating commonly is needed in sites with sub-zero temperatures and is usually effected by direct or indirect burning of natural gas or propane. Alternatively, cooling is required in areas with hot temperatures, or in mines with high underground thermal loads where the fresh air at ambient temperature cannot provide enough refrigeration. Thus, when the ambient air conditions cannot provide by itself enough thermal power to ensure safe underground working conditions, a heating or cooling plant is required, which involves a considerable equipment and operation cost."

Jan 1, 2019

By John C. Robbins

A new technique for the determination of trace levels of uranium in solution has been developed. A compact laser emits short, but intense, ultraviolet pulses to excite the green fluorescence of a uranyl-complex formed by the addition of a proprietary reagent to the sample. Organic species present in most natural waters also fluoresce quite intensely, but their emission does not last appreciably longer than the excitation pulse, in contrast to the relatively long persistence of the uranyl fluorescence . Electronic 'gating' is employed to separate the long-lived contribution, rejecting substantially the organic emission. Results using the laser fluorescence method on many sets of natural waters of various origins have been compared against corresponding values generated by independent laboratories. Correlation has been generally good over a range from less than 0.1 to more than 100 ppb U. Solid samples have also been analyzed after extraction of the uranium into solution. Accuracies adequate for most exploration purposes have been achieved, but further work is required to determine effects of interferences in samples with complex matrices. The transport and deposition of uranium in natural waters is controlled by the organic and inorganic chemistry of the waters involved. It is suggested that interpretation of very low uranium levels will be aided by additional measurements of conductivity and organic content, with subsequent statistical treatment.

Jan 1, 1978

By A. G. Darnley

"The Geological Survey of Canada is devoting consider-able effort to finding ways to make airborne radiometric measurements both quantitative and reproducible. Equipment has been designed by Atomic Energy of Canada Ltd. to provide high count rates in order to minimize statistical uncertainty, this being essential to justify applying terrain clearance and Compton scattering corrections to the data. Correction factors have been determined experimentally and can be applied automatically. Considerable ground work has been undertaken in parallel with equip-ment development in order to determine field parameters.Two airborne gamma-ray spectrometers are described. One is based on three 5-by 5-inch Nal(Tl) detector crystals and is used in a helicopter; the other employs twelve 9-by 9-inch detectors and is used from a Skyvan aircraft. The former is being used to investigate the range of radiometric response from specific rock types, and for the correlation of ground and air measurements; the latter has completed initial trials and will be commencing experimental surveys during 1969.Results are given to show the comparative sensitivities of the various detector sizes, and operational requirements for a gamma-ray spectrometer survey are discussed briefly."

Jan 1, 1970

By H. B. Farnam

"THE IRON ORE Company of Canada has been using do-it-yourself type explosives for three years. During the last 12 months we have used over 10 million pounds of ammonium nitrate-fuel oil explosives and either purchased or formulated one million pounds of slurried explosives.W e have been moving approximately one million cubic yards of stripping and ore per month and we expect our production rate to in-crease. Eighty per cent of our strip-ping and ore is soft enough to be blasted successfully with ammonium nitrate-fuel oil mixtures. Twenty per cent of our material is extremely hard and requires an explosive having greater strength than an AN-fuel oil mixture.W e had been using canned am-monium nitrate base explosives and TNT pellets to give maximum bottom loading density to fracture hard rock. As AN -fuel oil became widely used, it was apparent that other types of explosives could be formulated to fit our blasting requirements. Dr. M. A. Cook of the University of Utah was consulted regarding new explosives and together we developed the blasting slurries.Figure 1 shows a general view of one of our hard rock pits. The foot wall is on the right-hand side and this material is called iron forma-Figure 1.-General view of hard rock pitstion by our Company but is called 'Taconite by the operators on the Mesabi Range. This material runs 35 to 45 per cent iron and many pieces are hard enough to scratch glass. The formation is tilted at an angle of 55 degrees as can be seen in Figure 3.The bedding planes of this rock are about 24 to 36 inches apart and if the material is not well broken or fragmented, large chunks or slabs must be handled by the shovels which reduces shovel capacity and efficiency and increases maintenance costs."

Jan 1, 1960

This paper presents a case study where Cenozoic age detritals and an ancient buried landslide have been modelled in the final walls of an iron ore pit. Orebody 25 is located in Western Australia’s Pilbara region and is an operating pit where a redesign of the final wall cutback was required. The existing slope design utilised a simplistic geological model of mixed conglomeratic, calcretic and clay –dominated detritals overlying deformed bedrock sequences. This simplicity resulted in a conservative design that was not reflective of the slopes performance to that point. Further field investigation was carried out with the results assessed in conjunction with historic drilling, mapping and laboratory testing. A detailed geotechnical model was developed including three conglomerate and two clay dominated units and laterstage calcrete overprinting. The clay units were of significant importance to the stability assessment and resulting slope design due to the thickness and poor strength conditions indicated by the laboratory and field testing. However, the drilling investigation shed only limited understanding as to the origin of the clays and thereby how they should be treated as a component in the stability analysis. A comparison of the ratio of various geochemical elements measured by assay was made between the clays and 1) shale bedrock and 2) clays of known detrital origin from other nearby sites. This indicated the clays had a strong affinity with weathered bedrock. This and other textural features resulted in the interpretation that the clay units were relic debris preserved following ancient landslides in bedrock shale. Using laboratory testing data and calibration of results for a landslide origin, stability analyses were run, resulting in a steeper slope design being implemented. Excavation of the final cutback is now in progress with the model confirmed as appropriate.

Jan 1, 2015

By B. M. Currell, M. J. Neate, P. W. Bowden

Historically the hydrogen fluoride laden fume emitted from the electrolytic cells in the aluminium reduction process is further treated in pulse jet dust collectors. These dust collectors act as dry scrubbers performing two duties: adsorbing the gaseous fluoride emitted from the cells onto alumina dust; and collecting the alumina dust minimising particulate and fluoride emissions to the environment.Patented StarBag (TM) technology has been used in aluminium smelters in Australia as a means of increasing the dust collection and fluoride scrubbing capacity of existing collectors. This technology provides an alternative to major capital equipment upgrade where increased capacity is required, and potentially lowers the production cost per tonne of aluminium where capacity limitations are being realised and production expansion is required. This paper presents the findings of on-site pilot scale, and full production scale comparative tests, highlighting the operational and variable differences observed utilising the Star-Bag(TM) technology at Boyne Smelters Ltd in Australia. The results illustrate how this technology can be utilised to increase the hydrogen fluoride scrubbing efficiency and dust collection capacity of existing capital equipment.

Jan 1, 2006

By F. McCarthy, W. Zhang, R. McDonald

"The processing of nickel laterites has been a topic of major interest at CSIRO for almost twenty years. During this period CSIRO has collaborated with other researchers and industry in developing a better understanding of existing processes and been actively involved in testing/developing new beneficiation and process options for these ores. The current paper summarises the results of selected studies and highlights improvements that have been achieved. Key topics to be discussed include enhancements in the mineralogical characterisation, beneficiation approaches, improvements in the understanding and application of leaching technologies, the development of synergistic solvent extraction (SSX) for the recovery of nickel/cobalt from laterite leach liquors and the collaborative development of the Direct Nickel process. Future opportunities and key research questions will be briefly examined.INTRODUCTION Nickel laterite ores comprise a significant resource in Australia and according to United States Geological Survey data nearly a quarter of world reserves are located there (USGS, 2016). More specifically, around 95% of Australian nickel resources (laterite and sulfide) are located in Western Australia (Australian Government, 2017). Given the recent closure of Queensland Nickel, essentially all of Australian nickel production occurs in Western Australia and the primary producers of processed nickel products include Nickel West (Kwinana) with ~84,000 t saleable nickel metal in 2016 (BHP Billiton, 2017), Minara Resources (Murrin Murrin) with 46,700 t nickel metal produced in 2015 (Glencore Australia, 2017), and First Quantum Minerals Ltd (Ravensthorpe) who sold 25,882 t nickel as mixed hydroxide product in 2016 (First Quantum Minerals, 2017). The total sales of nickel from Western Australia in the 2015-16 financial year were 175,722 t. The study of nickel laterites at CSIRO recommenced at the time second generation High Pressure Acid Leaching (HPAL) plants were being commissioned at Bulong, Cawse and Murrin Murrin in the late 1990’s. A combination of technical and engineering issues meant that the ramp-up times at these operations were slower than expected and the outcomes resulting from the attendant problems are well documented (e.g. Griffin & Becker, 2000; Reid & Barnett, 2002; O’Callaghan, 2003) while the issues faced at the BHP-Billiton-built Ravensthorpe plant have been addressed by the current owners of this project, First Quantum Minerals Ltd (Piper, 2012)."

Jan 1, 2017

By P. J. Lunder, R. C. Pakalnis

This paper presents the results of research that has been undertaken in order to develop an improved method of determining the strength of hard-rock mine pillars. Pillars are found in various shapes and sizes in all underground mining operations. Prudent engineering design requires that if pillars are to perform as desired, both the pillar strength and the pillar stress must be determined. A detailed pillar stability study has been combined with an extensive database of published pillar case histories (178)resulting in a new “hybrid” pillar strength formula, “The Confinement Formula”, that utilizes classic strength of rock methods combined with empirical methods. “The Confinement Formula” utilizes a “mine pillar friction term” calculated from the average minor/major stress ratio with-in the pillar core. Statistically, the new formula provides better results at predicting pillar strength for the combined database than the best empirically ft pillar methods that currently exist. “The Confinement Formula” allows for the determination of the strength of mine pillars with an increased level of confidence over previously applied methods.

Jan 1, 1997

By F. Melo, M. Pawlik

Fine coal aggregation in concentrated coal-water suspensions was studied through steady-state rheological measurements. The wettability of coal particles was modified by dry oxidation of a bituminous coal. The degree of hydrophobicity was monitored using film flotation. The rheological measurements revealed that hydrophobic coal particles aggregate in aqueous suspensions, over a wide pH range, and produce slurries with high yield stresses. As the degree of coal oxidation increases, the coal particles become more hydrophilic and such suspensions exhibit lower yield stresses values. The yield stress values for suspensions prepared from oxidized/hydrophilic coal become a strong function of pH and correlate well with the surface charge as determined through electroacoustic measurements. These results indicate that the yield stress of aqueous suspensions of coal, and hence coal particles aggregation, is strongly affected by the wettability of coal particles.

Jan 1, 2004

By F. Vahdatikhaki

Simulation techniques have offered significant boosts toward a cost-and-time-optimized planning of construction projects by enabling project managers to effectively comprehend the behavior of projects. Using historic data from projects of like nature, simulation considers uncertainties involved in a project through accommodating the stochastic modeling parameters. However, the heavy reliance on the statistical data and not taking into account the context-specific features of the project cause the degradation in the realism and accuracy of the simulation models. Similarly, the extent to which a historic pattern could be retrofitted to new projects will decrease in line with the growing uniqueness of the projects and the novelty of construction methods. Furthermore, the existing real-time simulation frameworks are not capable of distinguishing the transient environmental changes, with minimal long-term impacts on the productivity, from the influential changes that will greatly impact an operation. In addition, existing simulation tools are devoid of location awareness, resulting in the inability to consider safety threats in their representation of the project. To address these issues, this research proposes a framework based on the integration of new tracking technologies used in Automated Machine Guidance (AMG) with simulation-driven 4D modeling methods. The proposed framework automates the adjustment of the simulation model based on the updated data from the site, and thus transforms simulation from a predictive tool used at the planning phase to a proactive monitoring platform usable throughout the planning and construction phases. A prototype is developed to test and demonstrate the effectiveness of the proposed approach.

Aug 1, 2013

By Malcolm Scoble, Nick Vagenas, Greg Baiden

Recent advances in underground communications technology have demonstrated the feasibility of teleoperation and automation in underground metal mines. One major challenge lies in the automation of underground mobile machines from surface, with the potential to reduce significantly the need for human involvement in underground operations. This paper reviews the evolution of underground metal mining automation, principally related to the development of teleoperation and automation of mobile mining machines. Examples of prototype systems are given and the associated benefits that have been observed are reviewed.

Jan 1, 1997

By A. N. Shen

Fe3A1 intermetallics are potential inexpensive candidate for hot applications. In this project, torsion tests on hot-rolled and annealed Fe3A1 (Fe-15.5A1-5.8Cr-1.0Nb¬0.05C) were carried out over the ranges 750-950°C and 0.01~1s-1 . The experimental results showed that when peak stress op>90MPa (LogZ>16s-1 , Z: temperature-compensated strain rate), specimens cracked at randomly low strains. Optical microscopy exhibited original elongated grains and many grain boundary cracks associated with segregation. With op<40MPa (LogZ<16s-&apos;), specimens deformed with low random op but considerably high fracture strains; slowly propagating cracks may explain the reduced flow stress. Optical microscopy showed both elongated grains and equiaxed subgrains with some indications of geometric dynamic recrystallization (gDRX) and of static recrystallization (SRX). Compression tests gave higher stress with little effect of the preexisting cracks. The activation energy Quw of current material in satisfactory torsion and compression tests is about 10% higher than previously published. Fe3A1 has body-centered cubic structure in the experimental range, so it was compared with ferritic stainless steel 434C (Fe- 16.55Cr-0.96Mo-0.21Ni). Constitutive constants and restoration mechanism are compared between these materials. While Fe3A1 is hardly a light metal, it is considerably lighter than most steels. Furthermore, like the other body centered cubic metals (BCC) (a-Fe, ß-Ti, ß-Zr and ß-brass), it exhibits a high degree of dynamic recovery (DRV) like Al alloys, producing easier hot workability than that of austentic stainless steels.

Jan 1, 2007

By Jerry C. Tien, Yingjiazi Cao

"Coal spontaneous combustion (SponCom) is a natural phenomenon in underground operations, which can either happen naturally or be triggered by human activities. For underground operations, espe-cially in coal, SponCom can happen frequently as a result of air leakage, although its incubation period may vary depends on types of coal and surrounding environment, resulting in uncertainty in control. In China, most of the underground coal operations now use longwall mining method because of its superior safety, high productivity and efficiency. With an increased popularity, there is also an increasing necessity to study spontaneous combustion, its occurrence and management. There have been many theoretical analysis and experimental studies over the past half century hoping to understand the occurrence of coal combustion and its control measures to better understand the occurrence and to design controlling measures to limit the dam-age it causes. In this paper, research on coal spontaneous combustion fundamentals from these three aspects will be reviewed, gaps highlighted and possible directions for future studies. INTRODUCTION The history of anthropic development is the history of human's energy utilization progress. From the first usage of fire, people have been continuingly seeking energy resources on earth. Coal, as an abundant, economic and convenient source of fuel quickly became indispensable and made significant contribution to economic growth worldwide. With technology and societal development, people are becoming more and more coal-dependent, but at the same time, problems of fossil fuel combustion came into sight. In global coal mining industry, spontaneous combustion has now presented one of the most challenging safety issues, it is also believed that it has contributed significantly toward the climate change. It is essential that more effort be invested to examine the cause of SponCom and its control measures. Coal SponCom is a complex process, with both physical and chemical inter-actions among various interrelated factors such as local airflow distribution, ventilation pressure, methane emissions (if any), and physical surroundings underground. With the advent of powerful computers, simulation techniques and af-fordable modelling packages in recent years, significant advances have been made in understanding sponta-neous combustion. But because of the complex nature of combustion and varying underground conditions, there are still areas that need further examining. This paper will focus on illustrating the current research of coal spontaneous combustion and addressing research gaps and future study areas."

Jan 1, 2019