Search Documents

By H. W. Kasaini, E. Bourricaudy, T. Larochelle

Rare Element Resources Inc., a U.S. based company, has developed a three-stage process for producing a +98% mixed REO powder from hard rock feedstock (-48 mesh, 2.9-4.8% REO) consisting of bastnaesite and ancylite minerals. Firstly, the whole ore is digested in chloride media at low temperature in counter-current flow mode. Secondly, the rare earths (REEs) are selectively precipitated as oxalates directly from an impure pregnant leach solution (PLS). Finally, significant amounts of free acid and water are recovered from the REE-depleted filtrate and subsequently recycled within the process. Excess heat from the oxalate calcination process is captured and reused in the plant. Due to the low leach temperature (45 ºC) and moderate acid dosage (240-297 kg/t, HCl), rare earth oxides (REOs) are preferentially leached out of fine solids leaving most of the base metals (Ba, Fe, and Al ) in the residue. Selective recovery of REEs from the PLS is achieved by mixing dilute oxalic acid (33% H2C2O4) and PLS at elevated temperature (85-95 ºC). The REEs plus thorium are precipitated as oxalates (REE2 (C2O4).xH2O) while the base metals are left behind in the barren filtrate. Multiple batch and pilot test results have confirmed that 50-80% of the oxalic acid can be recovered from the REE-depleted PLS through low-temperature crystallization (10-15 ºC). Typical leach efficiencies of critical rare earths at 45 ºC range from 85-99% (average 93%) while oxalate precipitation at high temperature increases the crystal size of RE oxalates (>450 microns, d80) thereby improving filtration. The economic benefits of this process include elimination of flotation and magnetic separation Capex and driving hydrometallurgical Opex down to $6- 7/kg, REO produced. As part of a comprehensive risk mitigation strategy, Rare Element Resources Inc has operated multiple pilot plants at SGS in Lakefield, Ontario, Canada to optimize counter-current leaching (CCL), REE oxalate precipitation (OXP), and thorium removal circuits. This paper presents pilot testing data from CCL and REE OXP circuits.

Jan 1, 2016

By E. Uzun

"In this study, H2SO4 and HCl leaching behaviour of an ore sample containing 1.87% of Ni, obtained from the Karaçam (Eskisehir-Turkey) lateritic deposit that started operation recently was investigated. Acid concentration, temperature and reaction time were investigated as variables by comparative leaching tests and the optimum leaching conditions were selected on teh basis of Ni, Fe, Co and Mg behaviour. For H2SO4 leaching, optimum leach parameters were 95°C, a 12 normal H2SO4 concentration and 90 minutes of reaction time, and under these conditions Ni and Fe dissolutions were 97.6% and 95.4% respectively. On the other hand, 70°C, an 8 normal HCl concentration and a reaction time of 90 minutes were found to be the optimum parameters for HCl leaching, and Ni and Fe dissolutions found were 97.1% and 97.8%, respectively.INTRODUCTION Today, nickel and various nickel compounds are obtained from sulphide and lateritic nickel ores (Moskalyk & Alfantazi, 2002). Even though about 72% of the world's nickel reserves constitute lateritic ores, only about 42% of nickel is produced from these ores. The decrease in production from sulphide deposits, on the other hand, and increases in the use of nickel in the iron and steel, and battery production sectors, and especially the production of nickel cast irons in recent years, have accelerated the importance of making use of lateritic deposits (Luo et. al., 2010; Chang et. al., 2010). In the beneficiation of sulphide nickel ores, mostly pyrometallurgical methods are used. On the other hand, about 39% of lateritic ores are beneficiated by pyrometallurgical, and 61% are beneficiated by hydrometallurgical methods (USGS, 2009). In laterite beneficiation, the ore properties are of significance; that is to say, limonitic ores are eneficiated by high pressure acid leaching or via the Caron process, nontronitic ores are beneficiated by high pressure acid leaching or heat treatment (smelting), and ores containing serpentine by pyrometallurgical methods (Berezowsky, 2004; McDonald & Whittington, 2008a; Dreisinger et. al., 2015)."

Jan 1, 2017

By J. Budac, E. Krause, C. L. Stewart, D. Wrana, S. W. Laundry

"As part of an over-all arsenic management strategy, Inco has developed a novel process that converts a by-product high moisture copper/arsenic sulphide precipitate into a crystalline copper arsenate suitable for the manufacture of wood preservation chemicals.The copper/arsenic sulphide precipitate is atmospherically leached with oxygen and sulphuric acid, producing a crude (blue) copper arsenate precipitate, elemental sulphur, and a copper and nickel containing solution. The blue copper arsenate is dissolved with sulphuric acid, the molar Cu/As ratio is raised to 2, and a crystalline copper arsenate (olivenite) is precipitated by the addition of sodium carbonate. Dissolved copper is recovered using metallic nickel (or matte) and elemental sulphur, to produce a low-moisture (low-arsenic) precipitate suitable for standard nickel-copper processing.The process was successfully piloted at Inco's Manitoba Division between September 1990 and June 1991. The copper arsenate product typically analyzed 43% Cu and 25% As, and the moisture content was about 10%."

Jan 1, 1995

By G. J. Simandl

"Since the 1980s, China has become the predominant producer of REEs. Recently, it introduced REE export quotas and this started a world-scale REE exploration rush. REE resources are concentrated in carbonatite-related deposits, peralkaline igneous rocks, pegmatites, REE ± P veins, ion adsorption clays, placers, and some deep ocean sediments. REEs could also be derived as a by-product of phosphate fertilizer, U processing, Ti-Zr-bearing placers, and exploitation of Olympic Dam-type sub-type of IOCG deposits. The ideal REE development target would be located in a politically stable jurisdiction such as Canada. REE grade and tonnage, mineralogy, and permissive metallurgy are some of the key technical factors that could be used to screen projects. INTRODUCTIONAccording to the International Union of Pure and Applied Chemistry (IUPAC), the term “rare earth elements” (REEs) encompasses yttrium (Y), scandium (Sc), and the lanthanide series: lanthanum (La), cerium (Ce), praseodymium (Pr), neodymium (Nd), promethium (Pm), samarium (Sm), europium (Eu), gadolinium (Gd), terbium (Tb), dysprosium (Dy), holmium (Ho), erbium (Er), thulium (Tm), ytterbium (Yb), and lutetium (Lu). This definition is used throughout this paper.REEs are subdivided into light (LREE) and heavy (HREE) categories. LREEs include, Sc, La, Ce, Pr, Nd, Sm, Eu, and Gd and HREE include Tb, Dy, Ho, Er, Tm, Yb, Lu, and Y. Promethium (Pm) does not occur in nature. Concentrations of individual LREEs in the upper crust of the Earth are comparable to those of base metals. Even the least abundant REE (Lu) is about 200 times more abundant than gold.The production of REEs, reported in the form of oxides (REOs), for 2011 is estimated at 140 000 t (Figure 1a). Although high technology industries can substitute several REEs with other materials, these substitutes are typically more expensive or less effective than the REEs they replace. A number of countries, including the United States, consider several REEs essential for national security, their economy, and a general reduction in green house gas emissions. The forecasted demand for individual LREOs is much higher than that of HREOs (Figure 2). Dy, Eu, Tb, Nd, and Y are essential for the US economy and subject to predicted supply disruptions (U.S. Department of Energy, 2010)."

Jan 1, 2012

By D. Karpoff

"IntroductionUNTIL the recent discovery and development of deposits at Allard Lake, on the Lower Romaine river, practically the whole of Quebec's - and indeed of Canada's - production of ilmenite had come from deposits in the vicinity of St. Urbain, Charlevoix •county, a village about eight miles north of Bay St. Paul on the north shore of the St. Lawrence, some sixty miles below the city of Quebec (see Figure l) . Although these deposits were known nearly three hundred years ago and were worked in a small way during the years 1872-74, when a charcoal blast furnace was operated by the Canadian Titanic Iron Company for making white pig iron, it was not until 1908 that more or less continuous production commenced and has •continued to the present by the American Titanic Iron Company. The whole of the output has been exported to the United States.The ilmenite occurs in lenses •and dyke-like bodies within anorthosite. Production has come chiefly from three deposits: General Electric, Furnace, and East and West Coulombe. During 1951 -52, an extensive diamond drilling programme was carded out under the direction of the writer to test the Furnace and the East and West Coulombe deposits (Figures 2 and 3), which form part of the property of St. Lawrence Iron and Titanium Mines, Limited. The average tenor of the orebodies encountered in the course of the drilling was 38.60 per cent TiO2 and, in addition to these high-grade •bodies, there was found a very considerable tonnage of lower grade ore."

Jan 1, 1953

By Magella Pelletier

"IntroductionDepuis une vingtaine d'année, les nombreux travaux de géochimie effectués par l'industrie privée et les milieux gouvemementaux ont permis:• de découvrir de nombreuses zones minéralisées a valeur économique;• d'identifier et de vérifier certains patrons de dispersion géochimique au-dessu s de secteurs minéralises déjà connus;• de favoriser le développernent des techniques analytiques;• de forcer le développement d'une mise en carte des résultats d'analyse, qui soit plus adéquat afin de permettre une meilleure interprétation géochimique.L'une de ces cartes géochimiques qui permet le mieux de mettre en valeur les données analytiques et qui fut instaurée au debut des années 80, est la carte d'interprétation géochimique par pondération.Cette carte numérique semi-quantitative, qui est construite à partir des données de base et de l'importance des éléments indicateurs pour une substance donnée, permet d'identifier et de définir des zones possédants de fortes probabilités pour la recherché de sources minéralisées."

Jan 1, 1987

By James H. Cobbs

Blind boring of shafts is becoming an increasingly important part of shaft sinking. Blind-bored shafts have reached diameters of 25 It in Europe and 16-1/2 ft in the United States. Much of the technology developed for blind boring has evolved from the technology of drilling wells for oil and gas production. Blind boring offers economic advantage in a number of situations where conventional shaft sinking either is extremely difficult or very expensive by virtue of large-capacity aquifers which must be penetrated, unstable ground or where very rapid sinking is required. In sedimentary rocks, blind boring is cost competitive with conventional sinking, in diameters of about 12 ft or less. Blind boring is not competitive with raise boring where conditions are favourable for raise boring. Blind boring does, however, offer greater flexibility than raise boring and can be performed in situations where raise boring is inefficient or impossible. Combination machinery has been developed to perform both blind boring and raise boring, so that the machine can be used effectively in situations where only the near-surface portions of the shaft are unfavourable for raise boring. Development work is being supported by the United States Bureau of Mines for blind boring equipment capable of boring shafts up to 30 feet in diameter.

Jan 1, 1979

By E. T. Turner

Introduction 1n assembling material for this paper on Wood Refuse Burning 1 turned first to the records of our early studies of the problem in order to learn how and why certain basic decisions were arrived at and also how it came about that the completed central steam plant differed so much from the original plans. It may be of interest, therefore, to outline the engineering problems as they presented themselves in the early part of 1948, and to indicate the economies involved. Although the principle of using wood refuse as boiler fuel instead of burning it to waste was quite sound, and in fact the practice had been in use for a long time in the boilers of many lumber companies, there was some guesswork as far as Hollinger was concerned in deciding how best to handle the large quantities of wood refuse involved and as to the type of boiler equipment necessary to .burn it efficiently. These problems will be examined first. Hollinger Boiler Equipment in 1948 Hollinger had four separate boiler houses, at Main, No. II, and No. 19 shafts, and a small unit at the compressor plant for heating purposes. Main and No. Il boiler houses operated all the year round; No. 19 and the compressor plant only in the winter. At Main there were four 36-year-old HRT boilers with total available h.p. of 500, at No. II, three 30-year-old HRT boilers with 195 available h.p., and at No. 19 two old field-type locomotive boilers capable of producing 95 h.p.

Jan 1, 1951

By P. D. R. Maltby

"The Canadian Institute of Mining and Metallurgy has undertaken to host the XIV International Mineral Processing Congress to be held in Toronto at the Royal York Hotel from October 10 to 16, 1982. The theme of the Congress will be ""Worldwide Industrial Application of Mineral Processing Technology."" The program will include 10 sessions and numerous field trips to the different mining areas of Canada.For prospective authors, the preliminary program includes sessions on,1. Flotation - plant practice, equipment design, simulation, control and economics.2. Comminution - plant practice, equipment, design, simulation, control, wear, energy consideration and economics.3. Round table seminar on large grinding mills.4. Round table seminar on modern and future plant design.5. Mineral processes to recover precious metals.6. Mineral processes to recover energy minerals (coal, uranium).7. Mineral processes to recover industrial minerals.8. Round table seminar on the environment and ecology and how the different countries cope with associated problems.9. Materials handling with an emphasis on agglomeration techniques ereconentration methods, solid-liquid separation.10. Open session to deal with topic emerging from general demand."

Jan 1, 1980

By A. O. Dufresne

WITHOUT transportation, mining would be quite impossible. Any person familiar with the operation of a mine knows full well that from the minute ore is blasted, it is kept moving until it reaches the treatment plant. In the mill, by means of conveyors and elevators, the ore is brought from receiving bins to one machine after another until finally its valuable mineral is separated from the gangue. The finished product must then be shipped -either by boat, rail, or motor trucks to industrial centres, where it undergoes further treatment and transformation into finished commercial goods. Everybody appreciates that the winning of an or-e includes, amongst various operations, the moving of large quantities of material of generally low value. Transportation, therefore, must be considered One of the most important factors in the economics of mining. My assignment, this afternoon, is not to treat of that phase of transportation as it directly affects mining operations, but rather to consider some of the aspects of overland transportation and its influence in bringing about the development of mining camps in Canada. I shall take the liberty of rapidly surveying conditions facing prospectors, mine developers and operators from the time a region is still in a pre-pioneering stage until such time as a mine starts shipping its concentrates.

Jan 1, 1956

By M. W. Grabinsky, J. H. Curran

"Characterizing the spatial distribution of rock stresses is a challenge, especially in the geologically complex environments typically found at most metalliferous mines. Therefore, instead of focusing, specifically, on the task of making stress measurements, the engineer should instead attempt to develop a better understanding of the interaction between stress, mining geometry and rock mass behaviour. This paper demonstrates such an approach using a Canadian Shield hardrock mine case study, in which geomechanical models are used to relate stress, mining geometry, and rock mass properties to observed excavation response, and numerical modelling is used to better quantify this interaction.IntroductionUnderstanding how the mine geometry, field stresses and rock mass interact to produce the observed rock mass response to mining can be a significant challenge. Consider our present ability to quantify the basic geomechanical design input data. Mine geometry is normally quantified in more detail than is required for analysis purposes. Our understanding of rock mass strength and stiffness is far from complete, but established procedures do exist to obtain estimates of these parameters based on index and laboratory testing data and field mapping. Our ability to quantify field stresses is probably the most limited, in part because stress measurements are difficult and expensive to carry out, and in part because the stresses vary to an unknown degree from point to point within the rock mass. The engineer must, therefore, consider whether or not stress measurements are justified and, when they are, where the average stress state needs to be quantified and how many of which type of measurements will be required to determine the average stresses.Such was the case at Ansil mine, a massive sulphide deposit in hard rock located at a depth of more than one kilometre in the northern Québec portion of the Canadian Shield. The Ansil orebody was relatively rich, but small, with the potential for significant stress-related problems. As a result, geomechanical design had to be done carefully from the start – there would be little opportunity to modify the mining strategy once production had begun, and the economic consequences of stope dilution and rock mass instability would be severe. An extensive stress measurement campaign was carried out, but the determined stress magnitudes were unexpectedly low. The designers were, therefore, faced with a dilemma:"

Jan 1, 1997

By A. Brown

"The first printed report on Canada's coal resources was published in Paris in 1672(1. Written by Nicholas Denys, then Governor for France of Isle Royale (Cape Breton Island), the report dealt exclusively with the coal of the Atlantic region because little or nothing was known about the interior of North America. Clearly, also, he wrote about a resource of which much was known among the military and early settlers of that day. This early knowledge is not surprising because the presence of coal is clearly displayed in the coastal cliffs of Cape Breton as it was also, at a later date, to the first arrivals on Vancouver Island.An example of early use was that of the French garrison at Fort Louisburg in the first half of the 1700s. Still earlier, in 1643, Governor Winthrop of New England reported the receipt of a small ship load of coal from New Brunswick (2). Despite this early knowledge there was no significant development of coal mines until the 1800s. This had to await the ending of wars between the French and British factions and the growth of population. Basically, also, its development awaited the beginning of the Industrial Age. Organized coal mining began in Canada in 1825 with the formation of the General Mining Association. This British firm was the creation of a group of London jewellers which had been granted royal rights, by the British crown, to all minerals in Acadia (substantially the present Maritime Provinces). The Association took over a number of existing small mines and opened up larger operations in the Sydney coal field. Subsequently, it expanded to the mainland Nova Scotia fields at Stellarton and Springhill. The Association continued in existence as the major coal producer in Canada until 1899 when it sold its properties to the Nova Scotia Steel and Coal Company, Limited (3). This Montreal-based firm managed the coal mines as a major Canadian producer of coal until 1968 when financial problems led to the expropriation of the mines by the Government of Canada. The federal government established the Cape Breton Development Corporation to operate the larger mines on Cape Breton Island. This Crown corporation continues to be a .major producer of coal in Canada."

Jan 1, 1985

By R. F. Tylecote

"The closure of the iron and steel making plant at Consett in Durham in 1980 marked the end of an era-a long era in the world's iron and steel making history. Iron had been smelted in the Tyne-Wear area of the United Kingdom since before the Roman period, but apart from evidence of smithing in the Roman period, the historical evidence for iron production on a large scale dates from the 14th century.The paper describes sites in the area that first worked the bloomery process and then, in the 16th century, as did most of Europe, graduated to the blast furnace process. The main emphasis is on the early introduction of coal to iron making at the end of the 18th century and the use of the steam engine to render integrated sites possible.IntroductionIron has been smelted in the Tyne-Wear area of the United Kingdom since before the Roman period, but apart from clear evidence of smithing in the Roman period, the historical evidence for iron production on a large scale dates from the 14th century. Like many other countries, the United Kingdom benefitted from the visits of foreign observers, such as Jars, Svedenstierna, de la Houliere and Dufrenoy, who left detailed records. In modern times, information gained from excavations of iron and steel making sites has supplemented the historical record.Natural ResourcesUp to the end of the 19th century, the industry was wholly dependent on its own resources. Iron ore, limestone, wood, coal and water power were all found a short distance away from the main valleys of the Tyne and Wear. The main sources of iron ore were the coal measures, with rider ores from the lead vein s in Alston and Weardale, and carbonate ores from shale horizons in the Carboniferous limestone. Good coking coal was available from West Durham and reasonable coal from the Tyne valley and Northumberland limestone. Limestone was plentiful."

Jan 1, 1983

By D. Vanin

"Conventional single heading track drifting in the hard rock mining industry has not shown any significant improvements in advance rates, despite the advent of modern track jumbos and igh speed muck handling systems .This paper presents Kiena 's experience in using a 7 ft 2 in. diameter larva Mark 6 Tunnel-Boring Machine (TBM) for driving 6000ft of drift.IntroductionKiena Gold Mines is located about 5 miles west of the town of Val d'Or, Quebec, approximately 300 miles north of Montreal. The mine commenced production in October 1981 and has gone through various expansions of ore production with 287 916 metric tonnes in 1982 to reach 453 800 metric tonnes in 1986.Due to the majority of claims being covered by a lake, a grassroots exploration drive of remote areas of the property was required to allow diamond drilling on a yearly basis. High speed sequential excavation methods (SEM) of single heading drifting in the mining industry has not progressed much in the past 20 years despite the advent of electric-hydraulic jumbos, Haggloader and Hagglund type cars. Certain examples of record SEM drifting advances have been performed in the past but only under very specific ground and cost conditions."

Jan 1, 1987

Reaction between xanthate ions in solution and oxidized compounds present on the surface of galena to form lead xanthate is considered to be a side reaction not contributing to flotation, although accounting for some consumption of reagent. The direct reaction of lead sulphide with xanthate and oxygen to form lead xanthate is the most significant to flotation. Coadsorntion of dixanthogen is also involved. Previous work has shown lead recovery in lead rougher flotation to be a function of m [H+] where: m = concentration of xanthate in solution rHl = hydrogen ion concentration. A plausible explanation for this relationship is suggest-ed. Likewise, the experimental findings that the amount of xanthate adsorbed under certain conditions is a function of m'[H+] are explained in terms of reaction between xanthate ions and soluble basic lead salts such as PbO.PbS04? It is also shown that m[H+] should have a constant value in lead cleaners operating at a higher pH than the roughers. This conclusion is confirmed by plant data, and the value of the constant agrees well with the calculated value. The finding is useful in mill control.

Jan 1, 1965

By A. Hutwalker, T. Plett

"Blast fumes are one of the major sources for NOx in underground mines. In 2016, the Occupational Exposure Limits for NOx in Germany were reduced by 90%. The task is to keep re-entry times after blasting at the present level and thereby ensure an economic operation of the mine. Measurements show that using ventilation solely is not sufficient. A new approach to reduce NOx from blast fumes is described. Laboratory experiments were performed and a reduction of NOx was observed. Measurements were conducted at an explosive factory’s testing facility and in an underground mine at blasting operations. INTRODUCTION Whether for production of ore or for drift development, the processes in an underground mine are always the same: 1) fracturing the rock, 2) loading the pile, 3) support the resulting cavity. The fracturing of the rock can be done mechanically, by cutting, for example by using continuous miners or tunnel boring machines, or by drilling and blasting. Drilling and blasting is more flexible than mechanical driving, as it can be used independently of the rock strength. Furthermore, this driving method allows a more flexible reaction to changes in geological and/or operational conditions. Thus, underground mining and blasting are almost inextricably linked with each other, and regardless of the size and level of technology of the mine, blasting is hardly avoidable. Depending on the mining method chosen and the existing framework conditions, such as the mechanical properties of the rock or the availability of machinery, blasting is an integral part of daily operations. Even in mines where blasting is not part of regular operations, it cannot be completely avoided. The blast fumes generated by the explosions are, in addition to diesel engine emissions, one of the two main sources of emissions of nitrous gases underground. Up to now, state of the art for dealing with blast fumes is ventilation. The fumes are diluted with fresh air and ventilated out of the mine. This treatment of blast fumes is more than sufficient with the former German Occupational Exposure Limits (OEL). The adaption of the OEL in Germany to the recommendations of the Committee on Occupational Exposure Limits (SCOEL), a committee of the European Commission, leads to big challenges for the mining industry in reducing the concentrations of these gases at the workplaces underground. On its meeting on May 2nd and 3rd 2016, the Committee on Hazardous Substances (Ausschuss für Gefahrstoffe, AGS), an advisory body of the German Federal Ministry of Labour and Social Affairs (BMAS), advised the BMAS to copy the OEL, as recommended by the SCOEL, to the Technical Rules for Hazardous Substances (TRGS 900). BMAS followed this advice, consequently the new OEL where published on November 4th 2016 and became part of the TRGS 900. Table 1 shows the former and new OEL for Germany. These new OEL became law after publishing, but two exceptions were made: For tunneling operations, they became law on October 31st 2017, for mining operations they will become law on October 31st 2021 (BAuA, 2004, 2016, 2017)."

Jan 1, 2019

By T. C. Cheng, G. P. Demopoulos

It is the object of this paper to discuss various options for improving the hematite process in terms of increased throughput hence lower capital cost and production of saleable quality hematite. With reference to increasing the throughput of the process, it has now been determined via the analysis of Akita Zinc Co's continuous industrial autoclave performance data that the process kinetics is limited by the rate of the hydrolytic precipitation reaction. By correlating the hydrolytic precipitation rate to supersaturation ratio, it is shown that accelerated kinetics can be achieved via the following measures: (1) in-situ neutralization with addition of zinc calcine; (2) elevation of temperature; and (3) dilution of feed; of which, the first one was retained for further evaluation. According to presented estimates, addition of calcine, amounting to only 2.6% of the total zinc calcine processed, can allow for shortening the retention time by at least 50%. Such drastic shortening of retention time may be either used to increase the throughput of a given autoclave circuit or alternatively to release autoclave capacity for clean hematite production. Hydrothermal treatment of the crude hematite product proved effective in producing clean hematite as according to laboratory tests, hence allowing the sulphur content of hematite to be reduced from around 4% to less than 1%. A conceptual flowsheet incorporating in-situ neutralization for accelerated kinetics with hydrothermal upgrading of crude hematite without sacrificing production capacity and with minimum upset of the plant's water balance is described.

Jan 1, 2004

By M. Phylli Bray

"Concurrent with the continuing demise of many Canadian mining towns is the rise of a new method of providing remote mine sites with a workforce. This is the Long Distance Commute (LDC) which uses commuter labour and requires no permanent settlements to support the mine operation. It provides a flexible and cost effective method of operation to the industry and relieves both governments and industry of the expense of building and maintaining mining towns. However, little attention has been paid to the effect on workers or their families of the LDC work schedule whereby workers spend a fixed number of days at the site followed by a fixed number of days at home. Off-shore oil rig experience would indicate that negative social impacts may be expected. Research leading to an understanding of the problems involved seems to be indicated. One innovative suggestion has been to use already established but dying mining towns as workforce pick-up points for new LDC operations further north.BackgroundUntil recently, mine towns were considered as a necessary component of mine development. This was a natural symbiosis resulting from the need to provide workforce accommodation close to isolated mine sites. The early mine communities in Canada were often just a huddle of shacks around a head frame. Gradually mining companies began to provide housing which varied from basic duplexes and quads in grid pattern layout to professionally planned and designed towns, either model company towns or the more recent suburbs-in-the-bush, the so-called ""instant towns"" of the postWorld War II era of resource development. The improvement in accommodation reflected the need to attract a stable workforce as mine operations became more sophisticated. City amenities were expected and offered in these mine towns as a way of encouraging a permanent community of mining families. Indeed in towns like Manitouwdage, Schefferville, and others, it was not unusual to find a significant percentage of two- and three-generation families apparently providing the permanent mining communities so desired by mine operators."

Jan 1, 1991

By R. M. Kleine

In the fall of 1968, Sheridan Geophysics leased the Renzy Mine property 50 miles northwest of the town of Maniwaki, Quebec. A 500-tpd flotation mill was dismantled at Belleterre, Quebec, trucked into the mine over a winter road and re-erected during extreme winter conditions. Approximately one billion gallons of water were removed from Renzy lake to expose the orebody. A 3,000-hp diesel generating plant and a self-supporting community were set up during the early part of 1969. This was a remark-able achievement considering that most of the work, including the pouring of foundations and the draining of the lake, had to be done during the winter months. Despite this, the project was completed ahead of schedule and one million dollars below budget. The mill is now treating an average of 800 tpd.

Jan 1, 1970

By W. G. Miller, J. D. Scott, D. C. Sego

ABSTRACT An overall study was conducted to evaluate the properties and processes influencing the rate and magnitude of consolidation for oil sands fine tailings produced using different extraction processes. As part of the overall study, a comprehensive description of physical and chemical characteristics of fine tailings generated by caustic and non-caustic processes was carried out. Ultimately, the influence of these fundamental properties on the compressibility, hydraulic conductivity and shear strength properties of the fine tailings was assessed. The characteristics of the fine tailings are presented in terms of index properties, mineralogy, specific surface area, water chemistry, liquid limits, particle size distribution and structure. A difference in water chemistry was concluded to be the cause of substantial differences in particle size distributions and degree of dispersion of the comparable caustic and non-caustic fine tailings. The degree of dispersion was consistent with predictions for dispersed clays established by the sodium adsorption ratio (SAR) values for these materials. A linear variation of increasing dispersion with increasing SAR up to a SAR value of about 40 has been suggested, above which fine tailings are completely dispersed. The observed dispersed or flocculated structures (viewed using a scanning electron microscope) supported the predictions based on SAR values.

Jan 1, 2010