Search Documents

By A R. Bonani, M P. Pe±a

The optimisation of slope angles, that is to say, increasing them, compared to the original design is always the subject of analysis of stability for geotechnical engineers and economic analysis for planning engineers. Questions to be answered include: What is the acceptable risk? What factor of safety? What probability of failure or reliability? The Rosario Open Pit has a history of failure, poor quality rocks and high pore pressures. It was decided to deepen the pit below the programmed design to test the practicality of different design approaches, which if successful, could be used to improve the economics of mining at Collahuasi. The revised slope design has factors of safety in the range of 1.0 to 1.2, probabilities of failure of ten to 38 per cent, and increased slope angles of between 3¦ and 5¦ with respect to the original design. The pit deepening with these design slopes will deliver an extra two million tonnes of ore which will have a significant positive impact on mining economics.

Jan 1, 2007

By P Moser, P Schimek, F Ouchterlony

This paper summarises the findings of 27 model-scale bench blasts in magnetic mortar, which were conducted from 2011 to 2014 at the blasting site of the Montanuniversitaet Leoben.The aim of the study was the investigation of the influence of blasthole delay times in small-scale bench blasts on the face characteristics and cracking damage created in the surrounding rock, which affects the fragmentation in subsequent rows.The test specimens or blocks, which were produced out of magnetite concrete, were roughly 1:100 in scale to normal bench blasts. The confinement of the testing blocks at the sides and back ensured the similarity to normal bench blasts with regard to the wave transmission into the surrounding rock. The specimen contained three or four rows with five blastholes each and were shot row by row, with virgin (undamaged) material in row 1 and increasingly damaged or preconditioned material in the following rows.The tested delay times varied between 0, 28, 73 and 140 µs, which corresponds to 0, 0.4, 1.0 and 2.0 ms/m of burden.The evaluation of the material properties showed that the use of magnetite concrete eliminated the inhomogeneous behaviour of rock, but some unexpected differences of the individual production cycles were still detected.The characteristics of the bench after each blast was evaluated along three horizontal lines out of a 3D model of the bench face. The tested delay time sequences of the virgin (first row) and single preconditioned blasts (second row) produced more overbreak for longer delays, while the third-row shots resulted in a smoothened surface independent of the chosen delay.The introduced damage after every blast was evaluated by an observation of irregularities on the newly blasted bench face. The visible cracks at the top of the testing blocks were documented and divided into several crack families according to their angle, length and origin. The remaining block was broken out of the blasting site after blasting, cut into several horizontal and vertical slices and dye penetrant spray was used to visualise the cracks created. Some of the detected crack families showed an influence of the delay time. The calculated mean crack density and mean crack intersection density showed that longer delays resulted in a higher degree of damage.The fragmentation results were well reproduced by the basic three-parameter Swebrec function. The observed improvement of fragmentation in the second- and third-row blasts was linked to the preconditioning of the burden for the following row while blasting the actual row. With the exception of the simultaneously initiated blastholes, the blasts showed coarser fragmentation for the shortest delays, while the longest delays generated the finest fragmentation.CITATION:Schimek, P, Ouchterlony, F and Moser, P, 2015. Influence of blasthole delay times on fragmentation as well as characteristics of and blast damage behind a remaining bench face through model-scale blasting, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 257–266 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By E A. Agorhom, M Beyuo, C Owusu, I Quaicoe

Understanding the mineralogy and liberation of gold particles in an ore is key to the development and optimisation of gold processing operations, being cyanidation or gravity separation. This can be achieved through basic historic geological information, gold deportment studies, chemical speciation and metallurgical test works. The present study assessed the nature of the occurrence of gold particles (mineralogical composition, liberation, associations and surface chemistry) and its effect on the process route (cyanidation and gravity separation) of a typical paleo placer gold ore deposit within the Tarkwaian Rock system. The investigative approach used involved chemical assay, quantitative X-ray diffraction (QXRD) and quantitative evaluation of minerals using scanning electron microscopy (QEMSCAN). The ore samples (A, B, C, D, E, F) used were obtained from six active pits of a gold mine working on this orebody. The results of the mineralogical analysis revealed that the ore is highly oxidised and comprised quartz (>80 per cent) and Muscovite mica (>6 per cent) as the major mineral phases in all the samples. Trace amounts of hematite, kaolinite and todorokite were also identified in all the samples. The chemical analysis showed presence of gold (Au) in all the samples with samples B (3.62 g/t) and C (3.96 g/t) containing the highest concentrations. Trace amounts of copper (Cu), iron (Fe), sulfur (S), aluminium (Al), arsenic (As) were also detected in all the ores. The QEMSCAN mineralogical liberation and gold association results revealed that the gold grains were relatively coarser in all samples (P80 > 80 µm Au in size) except F (P80 < 32 µm Au in size). Gold grains were highly liberated especially in sample B with the majority of the locked gold grains forming complex associations. All the samples responded well to cyanidation and gravity separation except samples C and F, respectively.

Aug 24, 2022

By J Rayner, R P. Langmead, J A. R Coote

Gosowong is situated within the Neogene magmatic arc of Halmahera island in the Maluku province of eastern Indonesia. It was discovered as the result of a rigorous ground reconnaissance program in an area with no previous mining activity. The broad structural setting in the Gosowong District comprises an elongate dome formed by the forceful upward intrusion of magma along a deep-seated structure, resulting in associated tensional fracturing trending parallel to the long axis of the dome. Four copper-gold porphyries and numerous low-grade epithermal veins occur within this mineralised corridor, with the Gosowong Deposit being the only economic occurrence discovered to-date. Gold mineralisation is hosted within multiphase epithermal quartz-adularia and quartz-chlorite fissure veins, breccias, and stockworks. High-grade gold mineralisation is emplaced in two gently south-plunging ore shoots along a 400 m section of the north-striking, east-dipping, Gosowong Fault, the primary control on mineralisation. The Gosowong Fault is believed to be a tensional fracture associated with uplift of the dome. Lithological variation and structural intersections play a large role in grade distribution within the vein zone. Host rocks comprise a wide range of shallow marine, intermediate-basic volcanic and volcaniclastic rocks of ?late Miocene age. The Gosowong gold deposit is a classic example of a low-sulphidation epithermal gold deposit, based on the abundance of adularia and illite in the alteration assemblage, and low base-metal sulphide content within quartz-adularia veins. The indicated resource is estimated at 0.99 Mt at 27 g/t Au and 38 g/t Ag for a total of 870 000 ounces Au, using a cut-off grade of 2 g/t Au.

Jan 1, 1999

By R Justa Cámara, L M. Pinillos Lorenzana

Barcelona Metro Line 9 (Line 9) is an essential infrastructure, improving the transversal transport in Barcelona by connecting the greater part of the currently existing radial lines. The purpose of Line 9 is to create a peripheral line surrounding the city of 1.6 million people (metropolitan area exceeds five million), and includes 52 stations, of which a total of 32 are deep shafts and 19 transfer stations in a densely populated area with several geographical constraints.The tunnel has an inner diameter of 10.90 m, bored with an earth pressure balance (EPB) tunnel boring machine (TBM) in soil sections with precast concrete lining type universal ring and segments 40 cm thick.A single tunnel solution was adopted, driven by functionality and costs savings. The internal tunnel section is divided into two levels to allow for one way rail transit including the platforms in each station on each level in order to optimise the space created by the TBM excavation and comply with the operational needs. The division in two areas of the tunnel was carried out through the construction of a horizontal slab resting on the tunnel segments with a constant thickness of 40 cm at the central part of the slab and supporting side walls.CITATION:Justa Cámara, R and Pinillos Lorenzana, L M, 2014. Two transit levels in one tunnel tube – an innovation in Barcelona Metro Line 9, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 387–398 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By N Mangadoddy, P Jampana, S Diddi

The study of air-core dynamics in hydrocyclone operation is essential for predicting separation efficiency in mineral processing. Electrical resistance tomography (ERT) allows non-invasive measurements of hydrocyclone internal flow dynamics. Existing regularisation methods such as Gauss-Newton and TV norms rely on optimisation techniques which have very high computational cost for very fine meshes. In contrast, the monotonicity method has much lower computational cost as it does not solve such minimisation problems. In this paper, results from the monotonicity method, Gauss-Newton (GN) (Tikhonov) and Total-Variation (TV) norm-based minimisation methods for estimating the air-core diameter in hydrocyclones are compared. We study these methods on the laboratory hydrocyclone experimental two-phase flow data. The results obtained are validated against High-speed video (HSV) imaging and Computational Fluid Dynamics (CFD) results. The results on different mesh sizes, in particular for very fine meshes with the number of cells ranging from 30 000 to above 100 000 are also investigated. The data used in this study is obtained from ITS Z8000 ERT system. This system does not measure the voltages on the current carrying electrodes. Since these voltage values are required for the monotonicity method, we implement an interpolation method to compute them. The results show that the monotonicity method provides a closer approximation of the interface between air and the water phases.

Aug 24, 2022

By M Hilden, K Barbosa, M Yahyaei, C Ndimande, K Runge, V Jokovic

Classification devices provide a link between comminution and flotation. Basically, it determines which particles are diverted back for additional grinding and which ones pass to downstream flotation. Therefore, the classifiers play an important role in the performance of a mineral processing circuit. Hydrocyclones are the most common classifiers used in wet grinding, despite being associated with poor classification efficiency. Hydrocyclones are widely used due to advantages related to low maintenance as well as reduced capital and operating cost. Other classifiers, such as fine screens, have much better classification efficiency compared to hydrocyclones. The major challenge of using screens in an operation, however, is their large footprint and increased maintenance requirements relative to hydrocyclones. Some researchers have demonstrated that switching from hydrocyclones to screens, as the classifier device in a ball milling circuit, resulted in a 20 per cent increase in plant throughput and significant improvements in coarse particle recovery, resulting in a 6 per cent increase in overall flotation recovery. However, it is known that these benefits of improved classification are very much ore specific, ie depending on the ore response. Therefore, there is a need to estimate the benefits of improved classification in pilot scale testing before the plant could consider the potential classifier upgrade. This paper presents the results of two pilot-scale grinding tests where the ore sample was processed using different classifiers: a traditional hydrocyclone and hybrid classification involving the use of a semi-inverted hydrocyclone followed by a screen. The size specific energy and circulating load were used to compare the performance of the grinding circuit. The grinding product was subject to mineral liberation analysis and the impact of classification efficiency on the mineral liberation is discussed in the paper.

Aug 24, 2022

The Mt Lyell Mine at Queenstown, Tasmania was re-opened in 1995 by Copper Mines of Tasmania Pty Ltd, a wholly owned subsidiary of Mt Lyell Mining Co Ltd. The re-opening followed over 100 years of copper and gold mining at Mt Lyell. Major changes in practice were implemented across the site. Preventing further damage to an already disturbed environment was a major priority. Sublevel caving, at a lower cut-off grade, replaced open stoping for the deep underground mining. Development and later stoping are handled by a contractor, National Mine Management Pty Ltd, in the largest underground contract awarded at the time. Large scale sublevel caving was new to Mt Lyell and not widely practised in Australia, requiring studies and systematic development of the method, particularly in drilling and blasting. Rehabilitation and upgrading of mine infrastructure have been and will continue to be a challenge. The mine has, since 1995, returned to being a stable producer with potential for growth.

Jan 1, 1998

By K Haroon, J D. Speed, S P. Wood

Online analysis of continuous and batch processes has seen a dramatic increase in recent years, with examples ranging from petrochemicals to pharmaceuticals, to industrial biotechnology and food and drink. The particularly challenging environment of alumina processing has meant that instrumentation needs specific features and characteristics to be truly suitable, features such as: robustness, resistance to caustic conditions both in the analyte and the ambient environment, and reliability for long-term continuous use. Here we present the development of a novel FTIR spectrometer that achieves these requirements through the use of a static optics arrangement of mirrors, and stable diamond-tipped light-pipe probe. Firstly we give a very brief explanation of spectroscopic analysis, and the difference between FTIR and other infrared methodologies. Next we outline the novel arrangement of mirrors required to produce an interferogram without moving mirrors, and compare the benefits and drawbacks of this approach instead of conventional designs. We then share the results of laboratory analysis of synthetic Bayer liquors, with detection limits for aluminium hydroxide, sodium hydroxide, sodium carbonate and various sodium salts of organic acids. We then share the results of analysis on production samples, both in idealised laboratory conditions and then online in the process itself. Lastly we present work on in situ ultrasonic descaling solutions to avoid scale build-up and provide continuous cleaning of the probe – preventing the need for probe removal and manual cleaning.

Aug 24, 2022

Mining had a very considerable effect on the country&apos;s development. The visual evidence remaining is an integral part of New Zealand history. Early mining for manganese and copper in the 1840s was succeeded by alluvial gold rushes. These gave way to hard rock extraction, hydraulic elevation and dredging. Coal mining dating from the 1850s was fairly widespread. Other minerals were obtained on a small scale. Manufacture of mining&apos; machinery stimulated industrial engineering enterprises. Schools of mines played a significant part in advancing technical skills and several remain as museums. Surviving mine structures and site relics are part of the industrial heritage signifying the technological and economic development of a small isolated nation. Some of these are described. Identification, recording and preservation where practicable is advocated.

Jan 1, 1990

By D B, M A. Sares, D W. Coulter, D C. Peters

This presentation discusses NASA-funded research on the ability of hyperspectral remote sensing to map diagnostic acid rock drainage (ARD) mineralogy that adversely affects water quality within watershed and to determine the relative contributions of natural ARD sources of metals and acidity to that drainage. Ground-based reflectance spectroscopy, combined with water chemistry, is used to identify mineralogical and chemical variations throughout a watershed. Integrated with hyperspectral data acquired from airborne remote sensing platforms, such as the NASA Airborne Visible Infrared Imaging Spectrometer (AVIRIS) sensor, a methodology has been developed that should improve environmental assessments and tracking of impacts on and from drainages. Phase I of this project focuses on a drainage basin (Lake Creek), tributary to the upper Arkansas River in central Colorado, which is impacted by natural acid rock drainage from areas of high-sulfide hydrothermal alteration. This project builds upon research and inventory efforts by the Colorado Geological Survey (CGS) to identify hydrothermal alteration that is the primary source or is contributing to acidic and toxic drainage in Colorado. This presentation will cover ground and airborne hyperspectral remote sensing techniques and results and water analyses for seasonal high-flow and low-flow conditions in Lake Creek. Identifying correlations between mineralogy, especially mineralogy that can be identified through airborne remote sensing, and water chemistry is a key focus of this project. Of particular interest are low-pH iron phases such as jarosite, ferrihydrite, schwertmannite, copiapite, and transitional amorphous phases as well as AlOH phases from higher, although still acidic, pH environments which are observed to mix with the iron precipitates within the streams draining from the hydrothermal systems. Drainage in the Lake Creek watershed derives from the Grizzly Peak caldera (Oligocene), which exhibits extensive hydrothermal alteration. Alteration types include silicic, quartz-sericite, quartz-sericite-pyrite, advanced argillic, and argillic. By understanding the chemistry of a naturally impacted drainage and its relationship to the surrounding geology, the project goal is to allow more efficient and complete identification of such sources in mineralised terranes through remote sensing technology.

Jan 1, 2003

By V Rimal, d M. Tangstad

Multiphase slags form the basis of the reduction pathway for manganese ferroalloy production. The present work aims to understand the flow of slag through the coke bed based on experimentation in controlled conditions. Synthetic slags of different basicities were evaluated for their phase composition, viscosity, and flow. The two-phase slag will have two zones: a liquid slag zone and a multiphase zone. The multiphase zone will consist mostly of a solid phase with some liquid slag between the solid particles. The multiphase part will hence have a high viscosity. The liquid zone will flow into the coke bed while the multiphase area will stay. With increasing reduction, the multiphase area will decrease in size until the solid phase is gone and the whole slag will flow into the coke bed. The effective viscosity of slag will decrease with the lowering of the solid oxide phase. The results from flow experiments confirmed that the segregation of phases occurs when slag flows through the coke bed. It is observed that the flow is dependent both on the size of the void and the viscosity of slag.

Aug 21, 2024

By D Matthews

Increases in mining and production capacities can have a major impact on the productivity of a mining and production facility during the construction and commissioning period. With minimised production loss in mind, a multi-phase modular plant design was implemented on the Khumani Mine in the Northern Cape, South Africa. The first phase involved a run-of-mine (ROM) crushing facility and the subsequent modular processing facility with capacity for 8.4 million tons per annum (Mt/a) product. An interim phase comprising modular additions to the processing facility increased capacity to 10 Mt/a product, with tie-ins occurring during maintenance periods. The second phase involves a second ROM crushing facility and modular additions to the processing facility, increasing capacity to 16 Mt/a product. This paper outlines the design considerations and limitations with modular design that need to be considered and shows how effectively construction and commissioning were implemented within shut-down and maintenance periods.

Jul 11, 2011

By T Raynlyn, J J. Campbell, R J. Holmes, J R. Manuel, S P. Suthers, A Poliakov

Prediction of the downstream processing performance of iron ore needs detailed information on mineral composition, textural peculiarities, particle density, porosity, mineral liberation and association and mineral grain size. Optical image analysis and automated iron ore texture classification systems are a way of obtaining such information. Furthermore, this information can be used for predicting the output of specific processes and their combinations. Several examples of the application of such an approach to process performance studies for iron ore are discussed. These include the application of classification by ore texture to modelling and optimisation of hydrocyclone performance, the effect of including textural information in modelling of sinter properties, and combining textural information with an experimental study of stirring and ultrasonic treatment of haematitic-goethitic iron ore fines to understand the deportment of fines and the breakdown/deagglomeration of particles. In all cases, the availability of textural information is important and helps provide a better prediction of process performance and/or understanding of the unit process.

Jan 1, 2008

By B M. H Sharp, R P. Hide, S P. Devine

Uncertainty and debate currently pervade the mining industry in New Zealand. The operational uncertainties, whether external (eg gold prices, the exchange rate), or internal (eg coal expansion difficulties), are large. In addition, many wider factors which influence mining are in a state of flux. State Coal Mines, the operating branch of the Mines Division of the Ministry of Energy I may be made a state corporation, with the remaining Mines Division functions being revamped. The agencies administering environmental legislation are to be restructured. Mining legislation amendments have been proposed and then dropped, and the area is now to be reviewed (The Press, 31 July 1985). Some mining licences have been withdrawn, and become the subject of heated debate in the community (The Press, 19 July 1985, and subsequent letters to the editor).

Jan 1, 1985

By W Newton, J Price

This paper outlines the design, justification and performance of a gravity circuit upgrade at the Marvel Loch treatment plant. The design of the upgrade was simple but effective. The key components of the upgrade were the addition of a sluice and a second Knelson Concentrator. The sluice was installed as a pre-concentration step. The upgrade also included the purchase of a Mineral Cone to treat the increased quantity of gravity concentrate. The cost was low because of the use of mostly second-hand equipment. The result was that for a cost of $75 000 the gravity recovery doubled and the overall recovery increased by over one per cent. This paper shows that you do not need to spend millions of dollars to be innovative and successful.

Jan 1, 2000

By Vink L, Johnson N. W, Mackenzie J, Young M. F, Johnston M, Landmark V

The influence of ore textures on metallurgical behaviour is poorly understood for most ores. An alternative method for characterising ore textures and for determining the resulting implications on ore processing has been developed for the Geor

Jan 1, 1998

By Cameron A

In recent years there have been significant developments in the tech- nology available for blast monitoring, analysis and simulation. Progress in these areas has been achieved through research conducted by explo- sives manufacturers and independent research groups from universities and mining companies. Miners are increasingly keen to exploit this tech- nology to help them design blasts which make optimum use of explo- sives to produce easily excavated muckpiles for the minimum possible cost. The art of blast design in the future will increasingly depend on an adequate understanding of the nature of the rock mass, the perfor- mance of explosives and the characteristics required of the muckpile to suit the chosen excavation machinery. Despite recent advances in blast simulation and the prediction of blasting performance, the best way to determine how a particular explosive will function relative to other explosives is to conduct properly designed and monitored field trials. This paper discusses recent work at Mount Thorley Colliery which demonstrates that field blasting trials can be monitored and analysed to provide quantitative data on the relative performance of bulk explosives. Techniques used in the trials included the sampling and analysis of explo- sives, insitu measurement of VOD, monitoring of near and far field vibra- tions, high speed and still photography and survey measurement of muckpiles. These techniques provided data for the analysis of throw, swell, fragmentation and burden movement together with data on the consistency and robustness of different explosive products. The blasting trials allowed both the shock and heave energy of various explosives to be observed in the field and led to the derivation of design rules for the use of differ- ent explosives at the mine.

Jan 1, 1988

By G A Brown

Environmental legislation is changing rapidly throughout Australia at the present time, and with that change comes additional responsibilities for the mining and petroleum industries. Among the many changes that are being made are increased penalties for both criminal and accidental environmental impairment. The defences for criminal offences are limited and for other offences the laws may impose strict liability - in effect the offender is guilty until proven innocent. Mines may be included under contaminated land legislation, creating additional liabilities for clean-up, rehabilitation and long-term management. It is not unknown in Australia for the value of a mortgaged property to be less than the amount of the environmental liability acquired by a mortgagor in possession due to contamination of the site. An essential part of the management program for resource projects is now the regular conduct of an environmental audit, the results of which assist in the management of the legal and financial liabilities facing company directors and managers. The audit can also assist with negotiations with government agencies, staff, unions, insurers, Aboriginal and other community groups. An environmental audit may also help to ensure that companies are claiming the maximum allowable deductions for environmental works under the tax laws, and provide evidence in support of such claims. Environmental legislation affecting resource industries Environmental legislation in Australia is changing rapidly and can impose massive constraints, substantial administrative costs, and considerable liability on directors, managers and the corporation. Pollution control legislation Every State and Territory of Australia has a range of pollution control legislation contained in either individual acts relating to air, water, noise and land, or embodied in a single environment protection act. Pollution control legislation provides a critical management baseline for resource industries throughout Australia, often requiring the full-time attention of an environmental manager or an environmental department. In general, it is an offence to discharge effluents into water, or emit gases into the atmosphere above prescribed limits, cause noise above a regulated level, or contaminate land without a licence. A licence determines how much of a substance can be discharged, the location, the receiving environment, the quality, and the time at which discharges can be made or noise can be caused. Planning legislation Planning legislation controls where a project is located, how it will be constructed and operated, how large it is allowed to be, and what will happen once the project is completed. Development consents or approvals will generally contain a range of conditions controlling the preparation of the site, the construction of the facility and the way it is operated throughout its expected life time. Resource projects may be regarded under legislation as scheduled or designated developments requiring special treatment during the decision-making process. Under planning legislation, it is usual for resource projects to be subject to an environmental impact assessment process. Resource legislation Resource legislation specifically covering mining and petroleum in Australia, also contains requirements regarding protection of the environment during exploration for and extraction of minerals and oil. A mining or petroleum production lease usually contains numerous conditions regarding protection of the environment and rehabilitation of the site during and after the life of the extractive process.

Jan 1, 1994

By N Madani, S Abulkhair, N Morales

Conventional geostatistical algorithms cannot reproduce bivariate complexities such as inequality constraint, nonlinearity and heteroscedasticity. Poor reproduction of these features may decrease the accuracy and reliability of mine planning results. For example, it is not unusual to have an inequality constraint between primary and disturbing elements in a metalliferous deposit. Implementation of traditional methodologies for such complex data sets can lead to the incorrect reproduction of a bivariate relationship, which will affect the validity of NPV results. In this paper, an iron data set containing iron and silica grades with an inequality constraint between variables is introduced as a case study. This study proposes an algorithm based on a hierarchical sequential Gaussian cosimulation integrated with inverse transform sampling. The proposed methodology considers the linear inequation between two variables in the hierarchical cosimulation process to reproduce an inequality constraint. As a comparison, conventional sequential Gaussian cosimulation is also applied to the same data set to demonstrate the difference in bivariate relationships from both models. Unlike the proposed algorithm, the conventional cosimulation cannot reproduce an inequality constraint and slightly overestimates silica grades. The modelled realisations are then used to assess the uncertainty of a plan and generate a stochastic strategy that adapts the destination of the blocks depending on the scenario. Two-stage stochastic long-term production scheduling takes extraction decisions using average information (ie e-type model) and ore/waste destinations based on geostatistical realisations. As a result, the proposed strategy is closer to the upper bound, highest possible NPV for each realisation, than to the lower bound, deterministic strategy that does not manage the risk of sending extracted material to wrong destinations. Furthermore, Comparing production schedules resulting from proposed and conventional geostatistical methodologies shows the importance of inequality constraint reproduction and more accurate long-term mine planning.

Nov 8, 2021