Search Documents

Mid-ocean ridges host approximately 65 per cent of about 100 known sites of high-temperature venting and polymetallic sulfide deposits; most of them are located at the East Pacific Rise (EPR), while more diverse mineralisation styles occur at the Mid-Atlantic Rise (MAR). Seafloor hydrothermal activity at the EPR are related to MORB while different substrates, including MORB and ultramafic intrusive rocks, are associated with æblack smokersÆ at the MAR. Depth of hydrothermal activity ranges from 0.7 to 4.3 km. High-temperature vents precipitating Cu-Fe sulfides (chalcopyrite and isocubanite, rare bornite), pyrrhotite, pyrite (¦ marcasite), and sphalerite, and low-temperature edifices precipitating marcasite (with pyrite), sphalerite, barite, andsubordinate chalcopyrite (pyrrhotite and isocubanite are absent) occur in both environments. There are considerable differences in Fe, Zn, Cu, Ag, Au and trace element contents in ores and in theFeS contents in Zn-sulfides in these deposits. Acomparison with anhydrite and sulfide minerals precipitating from modern black smoker fluids sulfide reveals many similarities but also some important differences. Fluids with salinity values above and below that of seawater at 400¦C down to 130 - 170¦C deposited sulfide minerals. Mantle-derived He prevails in fluids trapped by sulfides in EPR 9¦N and 21¦N hydrothermal systems. Hydrothermal fluids in MAR and back-arc systems are richer in radiogenic 4He. The sulfur isotope composition varies in the different hydrothermal fields and within zones of a chimney. EPR sulfides display narrower range of d34S values, while MAR and back-arc sulfides can bedepleted and enriched in the heavier d34S isotope. The most important finding is that fluid temperature, salinity, R/Ra ratios and d34S values ranged more significantly in the polymetallic sulfide deposits than when measured directly on venting fluids. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

By G M. Mudd

Mine tailings represent one of the two largest sources of mine waste from the minerals industries (the other being waste rock). Given the problems of declining ore grades and growing production, tailings generation is increasing exponentially across the global mining industry. Common practice is for mines to build large containment dams to store tailings during operations, which are then rehabilitated following mine closure. At some sites, however, the controversial practices of riverine or marine dumping of tailings is still practiced. As recent tailings dam failures have shown, there are legitimate questions being raised about the long-term viability of leaving tailings above ground due to the risks of collapse and failure. At present, it is rare for mines to emplace tailings back into former mine voids following mine closure, most commonly into a former open pit mine void (although a fraction of the tailings may be used for underground mine backfill, this is minor in scale). The approach of in-pit tailings has numerous advantages, such as inherent physical stability, low to negligible acid and metalliferous drainage (AMD) risks, as well as allowing more productive use of formerly mined land. In tropical areas where surface repositories are prone to leakage with potential for AMD and widespread dispersal of radionuclides (in the case of uranium mining), in-pit management provides particularly strong advantages – thorough hydrogeological studies are required, however, to address residual groundwater contamination risks and to establish sound, long-term environmental monitoring regimes for groundwater quality and subsidence issues. This paper presents a study of in-pit tailings management and compares it with surface repositories established in a tropical climate. The comparisons lead to the conclusion that, at least under tropical conditions, in-pit tailings management should be considered as world’s best practice – especially for radioactive uranium tailings.

Aug 8, 2011

Upgrading of Indonesia's Bauxite by Washing Method There were eight bauxite samples used in this research, three samples from Kijang contain total SiO2 18.36 - 29.16 per cent, Al2O3 40.12 - 48.36 per cent, Fe2O3 4.27 - 5.13 per cent, one sample from Tayan, contains total SiO2 4.69 per cent, Al2O3 38.95 per cent, and Fe2O3 19.67 per cent, and four samples from Mempawah contain total SiO2 33.5 - 44.8 per cent, Al2O3 29.8 - 35.9 per cent, Fe2O3 7.29 - 9.88 per cent. All of those bauxite ores have not fulfilled the requirement for Bayer process yet; therefore simple up-grading using a rotary drum scrubber is needed. The scrubbing process was carried out with time variable up to 60 minutes with solid percentage applied was 50 per cent and rotary speed was set up 30 rev/min. The bauxite was washed by following steps: scrubbing, screening, drying, and finally it was analysed to show chemical content. The washed bauxite produced has size fraction that is retained on the 1.7 mm of screen opening. The result of the research shows that the higher alumina content of the raw bauxite, the longer washing time is needed moreover the higher quality of the washed bauxite is produced. The highest alumina content of the washed bauxite was 53.67 per cent with the alumina recovery was 89.66 per cent and the concentration ratio of 84.80 per cent was achieved within 20 minutes of washing time of the raw bauxite (Al2O3 48.36 per cent). The washed bauxite resulted from this research is suitable as a raw material for Bayer process.

Sep 13, 2010

By Mercer J. K

Shaft guide reaetions in No. 2 Ore Shaft, Mount Isa Mines Limited, have been reduced to a low order of magnitude by the use of self aligning slippers and spring loaded guide rollers. Before commissioning the new 4500 h.p. winder at No. 2 Ore Shaft in January, 1958, it was realised that the increase in hoisting speed from 1800 to 2650 ft/min. would cause high shaft guide reactions which would be increased further when the elongated 12 ton skips replaced the existing 7 ton skips.The Cambridge accelerometer was used to measure the shaft guide reactions and to confirm that progressive skip modifications were resulting in reduced reactions. The skip modifications were completed in 4 weeks.INTRODUCTIONIn 1956 an expansion programme was initiated to increase production from 5000 to 11000 tons per mining day. At No. 2 Ore Shaft the 1500 h.p. winder operated at 1800 ft./min. and hoisted a 7 ton capacity skip. The new 4500 h.p. winder operates at 2650 ft./min. and hoists a 12 ton capacity skip. No. 2 Ore shaft is equipped with two 5 ft. by 5 ft. hoisting compartments (Fig. 1) and any increase in skip capacity meant an abnormally long skip. This feature, coupled with the increase in hoisting speed, could have caused very high shaft guide reactions. Before commissioning the 4500 h.p. winder, a Cambridge accelerometer was borrowed from the University of Adelaide and was used to measure the shaft guide reactions. Rather than carry out an extensive shaft timbering programme, the skips were modified by fitting cushioned guide shoes and spring loaded guide rollers (Fig. 1). Testing commenced in February, 1958, and was completed in March, 1958.

Jan 1, 1961

By M F. Lee

In order to make good decisions, as to whether large diameter raise bored shafts can be constructed in blocky rock at a particular location, mine planners, management, geotechnical engineers and contractors must understand and consider a range of geotechnical issues. Firstly, mine management must ensure that adequate time and resources are available to find appropriate shaft sites. Deep weathering, adverse structures, groundwater, etc might mean that the most desirable location, with respect to other mine development, might not be suitable. Special site investigation drilling, etc may be necessary. Even then, alternative construction options might be necessary, other than just reaming through to the surface. A site investigation borehole should then be drilled to investigate specific and general ground conditions along the raise alignment. Often, only small sections of weak blocky rock dictate raise stability. While the empirical McCracken and Stacey method is typically used in Australia to assess raise stability and assess geotechnical risk, until recently it had no published performance data.An Australian database of raise performance now exists and is presented below, courtesy of an industry survey by the Eastern Australian Ground Control Group. Raise diameter and ground conditions (in terms of a lower bound Qr value) is presented for 50 cases versus raise performance.

Jan 1, 2008

By N Tyson

Throughout Australia and the world, there have been in recent years a number of incidents involving the reaction of ammonium nitrate based explosives with ground containing certain types of sulphides. This paper presents a comprehensive strategy designed to identify, assess and mitigate the risks involved with blasting in areas of reactive ground. Undertaking blasting in reactive or potentially reactive ground involves a degree of risk, the level of which is dependent upon the controls in place for specific sites; this in turn depends upon the degree of sound reasoning and judgement behind the implementation of these controls. Implementation of controls to minimise the risk of incidents also involves a measurable increase in production and blasting costs. To achieve a balanced solution to this matter, decision-makers need to understand how the risks eventuate, how they should be evaluated, and how control measures reduce the risk. Also required is an understanding of how the problem affects the economics of the operation, and the magnitude of this effect. It is the aim of this paper to provide a structured approach to gaining this knowledge, so that mine management, the workforce and explosive suppliers may jointly develop more effective economic and safe blasting systems for potentially reactive ground. Using a combination of fault/event tree risk assessment and semi-quantitative analysis, a structured approach to dealing with the issue will be illustrated.

Jan 1, 2001

The green field discovery of a two million ounce high-grade refractory gold ore deposit in the Indonesian Province of Sulawesi Utara, led Newmont to utilise its proven technical expertise in dry grinding and whole ore roasting to develop a 2000 tonne per day, 160 000 ounce per year operation in this remote and picturesque location.Located at an elevation of 250 in above sea level and ten kilometres to a deep water natural harbour, the hard rock open pit mine, process plant and infrastructure facilities were built to budget at a capital cost of US$132 million. The plant was commissioned with oxide ore, with the first gold poured in March 1996 and with refractory ore in January 1997. The operation rapidly met its production targets because of extensive forward planning and training programs developed for the local workforce. The presence of steep topography, fertile coastal plains, high rainfall, high seismicity of this location led to the decision to dispose of neutralised tailings in deep water off the coast instead of impounding tailings in a dam. This paper describes the development of the project and the challenges in developing a gold operation in a remote location which lacked infrastructure, the steps taken to ensure a smooth commissioning, and the selection of the workforce to operate a technically sophisticated facility.

Jan 1, 1997

By M J. Cole, J Zhou, D J. Borrow, S M. Iveson, K P. Galvin, J L. Sutherland

New technologies can easily take around ten years to commercialise. Strong research support is needed in parallel with the process of innovation and commercialisation, in building a deeper understanding of the underpinning physicochemical and hydrodynamic forces that deliver the separations, in achieving improvements, in the deployment of a new technology, and in expanding the innovation platform to create new IP. External investment beyond the research, derived from the genuine value proposition of transformational change, funds the pathway for traversing the so-called Valley of Death.

Aug 24, 2022

At the Waikato North Head Ironsand operation, NZ Steel Mining Ltd is using a Bucket Wheel Excavator û shiftable conveyor mining system to excavate Titanomagnetite bearing sand and clay. The system utilises two Bucket Wheel Excavators with a two level shiftable bench conveyor and common trunk conveyor to deliver the material to a processing plant. The system was commissioned in November 1984 and has proved itself to be a high capacity, low cost method of excavating. Techniques of handling high sand faces have been developed and the conveyor layouts are going through a process of change to cope with the variable geo technical conditions and remain within: the characteristics of the excavators. The safety requirements for operating the system have been of a high standard and the experience has increased the confidence of the Company and the Mines Department Inspector's, for the first Bucket Wheel Excavator Mining system in New Zealand.

Jan 1, 1986

By B P. Wrench, N R. Steward, C Wu

A gold mine in southern China has transitioned from an open pit operation to a fully underground mine. An overhand mining method is used which requires the mined stopes to be filled with backfill having an unconfined compressive strength of at least 0.35MPa. Tailings from the process plant is deposited into separate flotation and Carbon in Leach (CIL) tailings storage facilities. The tailings has a high fines content and the thickener on site could only produce a dilute flotation tailings at a solids content of about 30 wt%. This resulted in two undesirable outcomes: the density of flotation tailings in the Tailings Storage Facility (TSF) was significantly lower than planned so that the TSF could not store the life of mine tailings and that the backfill product had to include a high percentage of manufactured aggregate and increased cement content to achieve the required strength. This paper presents results of a tailings study which identified that the flotation TSF would be capable of storing the remaining life of mine tailings if an amended backfill product made up of 100% of flotation tailings could be introduced. A 100% tailings backfill with the addition of 8% cement was developed by classifying the tailings and using the coarser fraction in the backfill. This backfill allowed 60% of the flotation tailings to be placed underground and only the remaining 40% in the flotation TSF. A new thickener was designed and installed to thicken the tailings and rheological testing of the tailings, using a closed loop pilot plant, provided parameters to upgrade the underground reticulation system to deliver cemented backfill to stopes throughout the mine and to deliver thickened tailings to the TSF. The revised design was implemented and has resulted in considerable cost savings. CITATION:Steward, N R, Wrench, B P and Wu, C, 2018. Optimisation of surface tailings storage and tailings backfill – a case study, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 454–464 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By Chappell B

Backfill in the form of mine waste tailings has inherent problems associated with attaining adequate strengths upon placement. Fines are usually removed to ensure adequate drainage, which lowers the cohesive strength of the fill, leaving the fines to he placed in a tailings darn. Electro-drainage and electro-chemical grouting is examined to investigate its effects on densification and shear strength within a silty clay tailing having low permeability and shear strength. Two separate grouting mechanisms are observed for the iron and silica grouts used. Electro- osmosis is associated with iron grout that deposits within the tailing matrix under a converging pH gradient, and increases the permeability of the tailing. This process initiates cation exchange and causes cementing of the granular contact points between the clays. Electro-phoresis causes sodium silicate solution to deposit silica grout in the voids of the tailings. The resultant effect of these mechanisms results in an increase in cohesion, leaving the void ratio of the iron grouted tailings as it was but significantly reducing the void ratio of the silica grouted tailings.

Jan 1, 1998

By D Matthews

With the increasing demand for quality-specific ores, coupled to the reality of even more complex minable iron ore reserves, there is a growing need for real-time online material analysis of plant feed and product. For a full system mass balance, the combination of conveyor weight scales, flow and density transmitters are required. This alone does not guarantee product grade. For optimal process control and material blending, real-time online elemental scans in combination with the mass weighting is becoming more than a ‘nice to have’. These elemental scans located at key positions, enable the mining and plant operators to make informed decisions timeously, therefore ensuring product outcomes and optimising operations where material grade and the control thereof are important. Typically, these units follow the mining and primary crushing circuit as well as on the product conveyors, low-grade conveyors and tailings lines. Deployed after the primary crushing circuit, an analyser acts twofold:1. guaranteeing mining production, and2. processing facility feed blends.The analysers on the product conveyors guarantee saleable product. The analysers on the low-grade conveyor and tailings line complete the elemental balance and identify the potential of the low-grade and tailings for future processing. The system losses (accumulation) are calculated to determine the amount of material ‘lost’ during the processing stage which does not report to any of the aforementioned and can be used as a measure of the efficiency of the plant. A further advantage of the real-time online analysis of material is that immediate intervention can be taken in the event that the product is not of saleable product grade requirements. In the Khumani Iron Ore mine, Northern Cape, South Africa, run-of-mine (ROM), product and control analysers were included. Run-of-mine and product stockpiles are certifi ed, low-grade material is not currently directly measured, but calculated from the internal control loops. Iron units are reconciled between product and feed material.

Jul 11, 2011

By J Krahn

In designing climate exposed soil structures such as caps and covers over mine waste it is necessary to include the wetting and drying influences of the local climate in order to accurately predict the net water, vapour and oxygen fluxes across the ground surface and through the base of the covers. The most advanced evaporative flux modelling tools currently available to practitioners have been limited to rigorous one-dimensional models (ie SoilCover) or semi-empirical two-dimensional models (ie Hydrus-2D). It is common practice to use the rigorous one-dimensional evaporative flux model results to develop a surface boundary function that can then be applied within a saturated/unsaturated two-dimensional model. However, this is not an ideal situation and results in a further approximation of the real system being modelled. This paper will highlight the use of a new modelling tool, VADOSE/W, which brings existing, rigorously formulated evaporative flux theory into the familiar setting of a two-dimensional model. The model is enhanced for simultaneous two-dimensional oxygen gas transport analysis, which has direct application in the mine waste industry. A key focus of the paper will be addressing the limitations of one-dimensional analysis for cover systems on sloping and hummocky terrain.

Jan 1, 2003

Banks' focus in using cash flow methods can differ markedly from that of equity investors. This paper attempts to explain and describe bankers' approach by: ò outlining the fundamental difference between banks' and investors' risk / return profiles. ò describing lenders' consequent use of cash flow methods in mineral valuation. areas. explaining lenders' specific treatment of key risk Fundamental to understanding banks' appraisal of mineral projects is the appreciation that lenders have a basically different risk profile and outlook from those familiar to equity investors. Lenders do not normally participate in any project upside. The economics of lending dictate that banks can only accommodate a low probability of loan default and consequently banks' principal focus in mineral ""valuation"" is ensuring an acceptably comfortable probability of debt repayment. A simple conceptual explanation of lenders' risk / return position is outlined.

Jan 1, 1994

By P C. Hagan, J Chen, S Saydam

Fully grouted cable bolts have been used in underground mining industry for more than 40 years and are becoming more and more popular especially when severe geological conditions are encountered, such as high stresses and large cross-section excavations. The axial performance of cable bolts are mainly relied on the load transfer process between the cables themselves and surrounding rock masses via grout annulus. Therefore, the selected grouts play a significant role in determining the reinforcement quality for underground openings. In order to better understand the mechanical properties of Stratabinder HP grout, which is one type of cementitious grouts commonly used in Australian underground coalmines, plenty of unconfined compressive tests are conducted on it. Following diverse standards, two different kinds of samples are prepared and tested with the w/c ratio ranging from 0.35 to 0.45. During the test important mechanical properties including uniaxial compressive strength (UCS) values, Young’s modulus, Poisson’s ratios and so forth are recorded. Based on experimental results, the effect of w/c ratio on the mechanical properties of Stratabinder HP grout is studied. Beyond that, influences of sample size on the failure mode, peak strength as well as residual strength of this kind of grout are summarised and analysed.CITATION:Chen, J, Hagan, P C and Saydam, S, 2014. Mechanical properties of cementitious grout serving in fully grouted cable bolting systems, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 269–276 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By K Esmaeili, S Aziznejad

Impact-induced rock fragmentation is a mechanism that is commonly used for rock breakage in drilling and crushing. Additionally, rock fragmentation by blasting is frequently used in rock excavation operations. Experience shows that the presence of discontinuities can significantly influence the impact-induced damage and fragmentation of rock. Quantification of the response of jointed rock masses to impact loads is complicated by the fact that the available laboratory tests are mainly designed for aggregates or intact rocks. It can be argued that neither of these tests adequately represent a jointed rock mass. This paper presents the results of a series of numerical simulations used to investigate the influence of pre-existing discontinuities on the impact-induced fragmentation of rock masses. The methodology includes determination of the static and dynamic mechanical properties of a rock unit by conducting a series of laboratory tests on intact rock samples collected from a quarry in Canada. A 2D distinct element code, Particle Flow Code, was used to generate a bonded particle model in order to simulate both static mechanical properties (uniaxial compressive strength, elastic modulus, Poisson’s ratio and indirect tensile strength) and dynamic mechanical property (drop weight tensile strength) of the intact rock. The calibrated numerical model was then used to construct large-scale synthetic rock mass samples by incorporating discontinuity networks of different intensity into the bonded particle model. Finally, the impact-induced fragmentation inflicted by a rigid projectile particle on the jointed rock mass samples, simulated by a synthetic rock mass model, was determined. More fragmentation was observed for the rock mass samples with higher joint intensity.CITATION:Aziznejad, S and Esmaeili, K, 2015. Effects of joint intensity on rock fragmentation by impact, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 377–384 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

Many stress measuring instruments use overcoring stress-relief principles but adopt different sensing techniques. Every technique is subject to certain limitations of rock types and conditions. To investigate the performance and reliability of the instruments in field measurement, a simple and practical approach has been developed to allow comparable laboratory results to be obtained which simulate in-situ rock and stress conditions. Four commonly used devices, the USBM deformation gauge, the CSIRO HI cell,the CSIR triaxial cell and the UNSW SI cell were thoroughly tested in the laboratory. Some conclusions have been drawn as to their suitability and reliability in different field conditions. Recommendations are provided for the choice of an appropriate technique for a given rock type and condition. A new thin-wall cell that overcomes the disadvantages of earlier devices has been developed and tested. Its laboratory performance shows that it has good prospects.

Jan 1, 1990

By F Saloojee, F K. Crundwell

Refractory ores need to be pretreated prior to cyanide leaching for acceptable gold recovery. Pressure oxidation is one method of rendering the ores more suitable for cyanidation. The focus of this work is optimisation of autoclave configuration for pressure oxidation. An autoclave for the pressure oxidation of a feed containing pyrite and arsenopyrite was modelled, using the population balance framework. The autoclave model takes into account feed particle size, reaction kinetics and retention time. Mass balance calculations were incorporated into Cycad Process« software. This allowed for the investigation of different circuit configurations. The base case model consists of a single autoclave. The feed was then doubled and additional autoclaves were added to provide the same residence time as the base case. Four different configurations for the additional equipment were simulated. These were parallel, series, series with inter-stage thickening and parallel-series circuits. The options are compared in terms of extraction and productivity. The parallel circuit behaves similarly to the base case. The series and series-parallel circuits have higher recoveries and productivities than the base case. The series circuit with inter-stage thickening provides the highest extraction and productivity. This is because the thickening reduces the slurry volume and increases the residence time of the solids in the downstream autoclave.CITATION:Saloojee, F and Crundwell, F K, 2013. Optimisation of circuits for gold pressure oxidation, in Proceedings World Gold 2013 , pp 181-188 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By C J. Berry, P H. Briggs

Assessment of metal mobility, acid rock drainage production, and toxic effects from weathering of mineralised materials (ie mine-waste piles and outcropping alteration/ore zones) is key in evaluating and mitigating metal mining sites. Many metal- and acid-generating materials at these sites are sulfur minerals (sulfides to sulfates) with differing reactivities, weathering characteristics and metal contents. Our working hypothesis predicts that data on the types and quantities of sulfur minerals, coupled with comparison of their sulfur isotopic compositions to that of aqueous sulfate in the surrounding environment, can be used to evaluate primary pathways of weathering reactions at mining sites. We developed a sequential extraction scheme to separate the phases of sulfur in mineralised materials. Operationally defined phases, including monosulfides, disulfides, elemental sulfur, water-soluble sulfo-salts, acid-soluble sulfates, and resistant sulfate phases such as barite, are quantified gravimetrically and/or instrumentally. Several sets of experiments were designed to test the effectiveness of this extraction scheme. First, a variety of ore sulfides diluted in an inert matrix was analysed with the scheme. Results showed that molybdenite and arsenic-bearing sulfides do not behave as predicted from just their sulfur oxidation states, indicating that samples containing these minerals need special treatment for complete phase recovery. Second, a natural mine-waste composite standard was analysed by the scheme. The sum of the phases was equal to the total sulfur concentration analysed independently. Each phase had a similar, but distinct sulfur isotopic composition. The results were verified with a laboratory prepared æproxyÆ having the same mineralogical composition as the standard, but with each phase having a very different sulfur isotopic composition. The sulfur isotopic compositions of the recovered phases from the æproxyÆ showed that the scheme effectively separated the sulfur with only minor cross contamination of phases. The speciation and isotopic analyses were applied to both mine-waste piles and naturally occurring alteration zones at nine mine sites. A case study from one site comparing the sulfur isotopic composition of minerals in an alteration zone and dissolved sulfate in proximal streams is presented. This case study shows the application of our data to differentiating sources of sulfate in the surrounding environment.

Jan 1, 2003

By M Simanjuntak, A M. Supomo

PT Freeport IndonesiaÆs copper/gold operation disposes of approximately 222 000 dry metric tonnes of tailings per day via two thickeners. Reduction of the flocculant dosage rates in each of the tailing thickeners has been achieved with the installation of Clarometers«, modifications to the existing operating DCS control strategy and a change in plant flocculant. This has reduced the flocculant consumption rate in the last twelve months by approximately 20 per cent. It has also highlighted the disparity in the settling rates of the two thickeners. Collaborative efforts between Cytec technical site engineers and Freeport operational personnel have made possible the overall gains achieved in the tailings thickener optimisation.

Jan 1, 2003