Search Documents

By M Andrew, D McTiffen, M Adams

A major Ventilation Upgrade Project commenced at the Fosterville Gold Mine (FGM) in 2017 to service the ongoing ventilation requirements of the underground mining operation. The project consists of three large diameter ventilation raises totalling 1100 metres, and new axial primary ventilation fans to upgrade the mine ventilation system. With a mining depth of 1200 metres and a thermal gradient of approximately 2.7 °C per 100 metres of depth, the completion of the Ventilation Upgrade Project is key to the ongoing success at FGM. The Ventilation Upgrade Project will allow continued mining, including high-grade gold deposits, lower in the mine where heat is increasing. Figure 1 below illustrates the underground workings at FGM, and provides a general view of the ventilation upgrade works to establish the new exhaust system from the lower workings to surface. Whilst raisebore pilot drilling the H4760 Return Air Rise (RAR) from surface to 395 metres, the raisebore drill string became stuck in the raisebore pilot hole at approximately 300 metres down hole, presenting a significant technical problem and delays to the project. This Case Study provides an overview of the recovery process undertaken at FGM including the recovery of the stuck drill string. The value of the stuck in-hole equipment, the investment in the shaft site preparation, the collar stabilisation, the underground development to the base of the ventilation raise, the surface footprint prepared for the Primary Fans construction and the limited available space on the site were all motivations to recover the raisebore drill sting and ultimately recover the ventilation raise location. More importantly, the long lead-time required should a new shaft location be the final solution, and the delay this would incur to the ventilation upgrade was unacceptable. Recovery of the drill string was not possible using the capability of the Contractor’s Raise Drill. An alternative method for freeing the drill string was required. A significant amount of engagement with industry was undertaken to seek out potential solutions and draw from the experience of others. All methodologies available were considered and assessed. Ultimately, after several attempts at freeing the raisebore drill string using various methodologies, Adams Drillers and Clear Cut Interventions were engaged to provide a turnkey recovery solution.

Mar 15, 2021

This paper describes a case history of using an integrated geochemical and hydrogeological approach to predicting solute transport from gold mine tailings in highly fractured volcanic terrain. Two modes of transport are identified, namely discrete fissure flow and diffuse seepage through the intervening weathered rock. A simple mass balance approach is used to predict concentrations at points of emergence because most of the seepage migration will be by way of the discrete fissures where advective transport will predominate. The mass balance method has been modified to allow for natural degradation of weak acid dissociable cyanide. The long term effects of diffuse seepage are also examined.

Jan 1, 1988

Comminution Kinetics equations are developed to take into account difference of grindability of mineral components. The equations describing both batch and closed circuit grinding or crushing processes are given. These equations are applied to industrial data to derive comminution kinetic and classification characteristics of the component minerals in a multi-mineral ore. Control strategy based on these concepts is presented.

Jan 1, 1985

The Charters Towers goldfield in northeastern Queensland produced over 206 tonnes of gold from gold-quartz veins hosted by Mid-Palaeozoic granodiorite, tonalite, diorite and to a lesser extent amphibolite-grade meta-sedimentary schist and meta-igneous rock. Mineralisation occurs in grouped, moderately dipping shear zones with altered wallrock rafts and a complex network of quartz veins.Over 75 per cent of the production came from three main vein systems in the central goldfield: the Brilliant, Day Dawn and Towers Hill vein systems.The Brilliant vein system is hosted by undeformed tonalite and contains north-plunging oreshoots on a north-dipping main fissure and on shorter east-dripping hangingwall fissures. The Day Dawn vein system is localised along a north-dipping dyke at the contact of two deformed granitoids in a brittly reactivated mylonite, where horizontal oreshoot plunges may be related to the original megascopic undulations in that structure. The Towers Hill vein system is hosted in two granodiorite types and has multiple ore controls.Structural analysis indicates that the distribution of the oreshoots within the vein systems is variously controlled by the primary fabric and igneous contacts of the granitoid host rocks. Splaying, changes in dip, and fissure intersections are the main controls. The largest vein systems are both in reactivated shallow-dipping mylonite, or in fissures in younger undeformed granitoids. Each vein system lies in a separate structural domain, usually where older east-striking structures are preserved.

Jan 1, 1990

By Tarvainen M, Mattila O

Outokumpu Oy has systematically developed the automation of mineral flotation covering the technology of both new devices and control methods, and as a practical result of this effort currently produces two on-stream X-ray analyzers. The Courier 300 system basing on conven- tional X-ray technology is applied to complex or large processes. The newer Minexan 202 dis- tributed probe system based on radioisotope technology is developed mainly for simple or small scale applications. In this paper aspects and experiences of these analyzer systems and their applications for flotation control are discussed with particular reference to the role of the computer

Jan 1, 1977

By Nixon C. A

The exploration of Mount Isa Mines' new copper source will require the development of a five kilometre 4.7 x 5.5 metre blind decline commencing 1000m below the surface and extending to 1600m below the surface. With virgin rock temperatures approaching 60¦C, the ventilation strategy represents a complete departure from any previously used at this mine, in that refrigeration becomes essential. The use of direct water to air cooling techniques has become commonplace in mines throughout the world and their application is being adopted at Mount Isa Mines. A heat load simulation routine has been implemented to allow for the design of refrigeration requirements, as well as to aid in the selection of diesel or electric equipment. This enabled planners to determine the size of a surface based refrigeration plant. Future refrigeration demand for expansion into the ore production stage has also been investigated.

Jan 1, 1988

By M Lee, J F. Carswell, G Reitsema

"The increased costs of underground mining have continually challenged engineers to identify opportunities for alternatives to common approaches to underground development. Considerations to the design of horizontal and vertical development at the Dugald River mine targeted inclined raise boring to reduce horizontal development, not only to reduce cost, but to allow development activities to focus on other areas of the mine.The mine plan consists of 50 raise bored ventilation shafts, of which 17 have been mined to date with diameters ranging from 3.1 m to 5 m and lengths from 30 m to 200 m. The expected performance and stability of these shafts has been determined using methodologies proposed by McCracken and Stacey (1989) and further refined by Peck, Coombes and Lee (2011). Actual raise performances have been collated and compared to a database of raise bore performances across Australia as presented by Coombes, Lee and Peck (2011), and form a database of raise bore performance specific to Dugald River.Opportunities to further optimise the mine plan and reduce costs have seen the introduction of large diameter-inclined raise bored ventilation shafts to minimise the required lateral development to connect the ventilation circuits. Large diameter inclined shafts ranging between 3.1 m and 4.5 m in diameter have been successfully mined with dips down to 70°, reducing the cost of lateral development by more than $1 million over the next two years.Both technical and operational challenges were overcome in the mining of large diameter-inclined raise bores, including modification of: existing methodologies of assessing shaft wall stability for inclined raises. These included variations of the McCracken and Stacey method and the utilisation of the modified stability number (N’) previously developed for stope performance (Potvin, 1988). both the collar and toe development profiles, including the general set-up of the raise bore drill rig to reduce the operational risks associated with angled raises.Due to their success, inclined raises have been designed for subsequent stages of the life-of-mine ventilation system at Dugald River. This has resulted in significant capital cost savings for the mine.CITATION:Carswell, J F, Reitsema, G and Lee, M, 2017. Vertical and inclined raise bore performance at Dugald River mine, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 313–320 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 16, 2017

By Mayer TE

The Granites Goldfield is located 550 km northwest of Alice Springs. Mineralisation was discovered in 1900 and intermittently worked along nine km of strike until the early 1950's, yielding a recorded production of 470 kg of gold. The geological environ- ment, pre-existing exploration drilling results, and an optimistic view on gold, prompted acquisition of the property by North Flinders Mines Limited in 1975. An agreement was signed with the Central Land Council in August 1983 and drilling commenced in the same month. In the past, gold was won from alluvial deposits, rich quartz veins and lower grade, disseminated stratabound mineralisation. The last is contained within a distinctive unit in the Mt. Charles Beds, of the Early Proterozoic Tanami Complex. This informally named "Host Unit" is a metamorphosed, chemical- pelitic sediment. The schist contains variable proportions of amphibole, quartz, garnet, clinopyroxene, carbonate and sulphide, inter- calated with recrystallised chert beds. Free gold occurs in several mineralised horizons within the Host Unit, generally conformably distributed within lithologic bands or at lithologic contacts. The Host Unit occurs within a sequence of metamorphosed pelitic sediments and intermediate volcanics. Although mostly confined to the Host Unit, stratabound gold mineralisation also exists in both Footwall and Hanging Wall Schists, usually within zones displaying certain Host Unit characteristics. The deposits may be loosely categorised as being of banded iron formation (bif) type, although some important differences are noted between them and classical bif type orebodies.

Jan 1, 1984

Recovery of tin and copper from concen trates containing cassiterite, stannite and chalcopyrite was studied in laboratory-scale tests designed to simulate continuous operation of the matte fuming process in which tin is recovered as SnS fume while copper accumulates in the matte. Charges made up of 300g of mixtures of the concentrate and siliceous flux were added at a uniform rate in pelletized form to crucibles containing 300g of matte and 50g of slag (both of which were recovered from previous tests), while blowing through the matte with air or oxygen-nitrogen mixtures at a rate of 3 to 5 1/min. Accurate material balances enabled the effects of process operating conditions on tin recovery and sulfur utilization to be deter- mined. When operated correctly, the matte fuming process gave tin recoveries exceeding 90 percent in spite of wide variations in the copper content of the matte and in the operat- ing conditions. Deterioration of tin recovery was associated with undersaturation of the slag with respect to silica, and with high partial pressure of sulfur dioxide (greater than approx- imately 0.2) brought about by oxygen enrichment of the blowing air. The utilization of sulfur varied widely in low grade mattes. Copper in excess of approx- imately 10% promoted formation of SO2 by the commonly accepted reaction: FeS + 1-120 2= FeO + S02 while in copper-free and lower grade mattes a substantial fraction of the oxygen was consumed in the alternative reaction FeS + i 02 = FeO + z S2.

Jan 1, 1980

By Propster M, Choudhry M

THIS note gives comments on the paper by Kitaev et al on p. 68 of this book and compares results with those obtained by ourselves. We wish to say that the authors are to be congratulated on their sophisticated approach to an important problem and that it complements our efforts on flow maldistribution.1-5 It is our view that Eqs. (1)-(5) on p. 69 are impressive, but unfortunately with present day computers and computational facilities, it would be quite impractical to contemplate the numerical solution of these. Eq. (8) in the authors' paper, on p. 70, does provide the logical starting point for tackling flow maldistribution problems and strictly speaking this equation is more accurate than Eq. (1) in our paper in this book. We note in passing that there is direct experimental evidence to support the contention that our Eq. (1) is at least a reasonable approximation and one may question in a practical sense whether the refinement afforded by Eq. (8) in the paper by Kitaev et a/ is justified. While one must readily accept the appropriateness of Eq. (8) of Kitaev et al as a starting point, the subsequent mathematical manipulation by the authors is open to serious criticism. In order to solve this complex, non-linear equation Kitaev et al postulated irrotational flow, which afforded considerable simplification. One can argue simply on physical grounds that the assumption of irrotational flow is inappropriate, a fact which should be readily apparent on inspection of the flow fields shown in Figs. 2 and 3 of Kitaev's paper. It follows that while the starting point through the use of Eq. (8) is correct the results derived from this starting point may be suspect because of the erroneous nature of the irrotational flow assumption.

Jan 1, 1975

By Lawson F

Synthetic calaverite (Au Tez) has been prepared and its physical properties checked.Simple flotation tests indicate that the recovery of calaverite should be possible using n-butyl or sec-butyl xanthate collectors under approximately pi I neutral conditions with a copper sulphate activator.Roasting calaverite in air at moderate temperatures resulted in its decomposition with the formation of elemental gold and tellurium dioxide.In alkaline oxygenated cyanide solutions, both gold and tellurium tend to dissolve. At pHs less than 14, about 50 per cent of the tellurium remains as elemental tellurium; however in very strongly alkaline solutions, essentially all of the tellurium is converted to the soluble tellurite ion (TeOl-).However, even at high pHs, the solubility of gold in the cyanide solution is still low due almost certainly to passivation effects.

Jan 1, 1991

By Coppock BW

Sintering of lead and zinc concentrates is practised by Sulphide Corporation Pty. Limited to provide both desuiphurised lump sinter feed, for simultaneous reduction to zinc and lead in the Imperial Smelting Process blast furnace, and sulphur dioxide gas for sulphuric acid manufacture. From November, 1969 a 20 percent increase in production rate has been obtained through improvements in operating technique. A gradual increase in bed permeability was achieved by modifications to the feed mix conditioning equipment and by improving moisture control. However advantage could not be taken of the higher permeability to increase sulphur elimination because the hardness of the lump sinter decreased. Higher throughput, better quality sinter and more stable sintering conditions were however made possible by simultaneously: 1. reducing segregation and compaction in the sinter bed, by narrowing the discharge opening of the main layer feed hopper, 2. reducing the sizing of sinter returns to give a closer size spectrum of particles in the feed mix, and 3. increasing the sulphide sulphur content of the feed mix to give higher bed Temperatures.

Jan 1, 1972

By Hill J. R M, McDonald M. M

A prediction technique for support perfor- mance of hydraulic backfill in narrow stopes is applied to two stopes separated vertically by a sill pillar. Predicted stope wall closures and fill pressures compare favorably with field measurements taken over a period of several years at two mines in the Coeur d'Alene dis- trict. Stope wall closure and peak pillar stress can be substantially reduced by improved fill quality within a practicable range of fill and rock properties.

Jan 1, 1973

The O.K. deposit occurs within a belt of cherts and spilitised basic volcanics near the western margin of the Hodgkinson Province. The tabular to lenticular shape and gross conformability of the ore bodies; the common occurrence of colloform, framboidal and banded textures in the ores; the lack of significant alteration adjacent to the massive ore horizons and the apparent restriction of stockwork mineralization to the foot-wall side of the massive ore zone at the O.K. mine, all favour a syngenetic origin for the massive sulfide bodies. Furthermore, the micro- structural evidence suggests that the ores have undergone the same deformational history as the country rocks. The invariable association of the ores with spilites; the S isotope values and Co-Ni contents of the pyrites, together with the primitive metal assemblage (Fe, Cu, minor Zn) strongly favour a basic magmatic source for the sulfides. It is suggested-that the sulfides were probably precipitated sub aqueous- ly during a hiatus in volcanic activity. The O.K. deposit is of the cupreous pyrite variety, but unlike other well known occurrences of this type, it does not con- stitute part of an ophiolite complex. While the host volcanics exhibit strong ocean floor tholeiitic affinities, no associated ultra

Jan 1, 1978

By T J. Laing, A B. Richards, A J. Moore

Blastholes fired in a pattern with a constant initiation delay create a frequency in the ground vibration similar to that from a percussion instrument, such as a drum, in the air. A constant firing delay generates a prime or forcing frequency into the ground motion. The forcing frequency may then be modified by ground transmission characteristics into subharmonics of the forcing frequency. The moving vibration source between blastholes also creates a frequency shift because of a Doppler effect. Other wave interactions may form beats. The effects are exacerbated by the accurate firing times of electronic detonators. This paper demonstrates how observations of wavetraces and frequency spectral analysis were used to recognise:Doppler effect and frequency ellipsoidssubharmonics (and sub-subharmonics) of the forcing frequencybeat formation that may double or triple peak particle velocity (PPV) levels.Recognition of beats permitted techniques to be used to control ground vibration from coal overburden blasting to limits deemed to cause no further instability in a slip failure. An understanding of the science involved has practical application elsewhere that has been successfully applied to initiation timings to reduce PPV and adverse human and structure response from other blasting operations.CITATION:Moore, A J, Richards, A B and Laing, T J, 2015. Blasting harmonics and controlling peak particle velocity, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 527–532 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By Pradhan GK

Blasting is one of the most important operations involved in surface coal mining. The removal of over-burden waste in surface coal mines of India had experienced many improvements in terms of blasting, explosives selection, blast design, equipment selection, deployment. etc. Two case studies of very large surface coal mines have particular importance in their blasting operations. Both these units have been equipped with large capacity excavating machines, hauling units and also have some difficult mining situations. Blasting is done in benches in close proximity to human dwellings and over coal seams developed by underground methods with problems of high wall stability etc, as well. The various steps taken to improve the blasting operations ensure smooth operation of the equipment to meet the targetted coal production.

Jan 1, 1991

The first hydraulic roof supports were installed underground in 1950s and ever since that time engineering developments have improved the supports in many different ways. However. advances in three main areas, the roof support mechanical design, hydraulic engineering and electronics have ultimately led to the point where, 35 years after that first installation. automation has been achieved and is now commonplace.The history of roof support automation has involved the continual integration of high technology engineering. Thera ate further possibilities for the future which combine to give some idea of the likelihood of there ultimately being a completely manless face.

Jan 1, 1991

By Reeves I. And Farquhar J, Pearce S

The irregular shape of the Rosebery orebody, coupled with the inconsistencies in grade over short strike lengths, has meant stoping blocks have had to be small to combat dilution and stability problems. In the past, each lens was divided into regular block sizes and developed up to five years before production commenced. There were two major drawbacks to this practice; firstly, existing development deteriorated over time therefore requiring rehabilitation prior to production. Secondly, the pre-determined blocks could not be easily changed to incorporate changes in mining technology or economic circumstances. Bearing these problems in mind, it was evident that any new lens development had to be designed to allow maximum flexibility. The lens being currently developed is J lens. It represents approximately 50 per cent of the current reserves tonnes, and 65 per cent of the zinc metal. Its importance to the mine's future cannot be over emphasised. At its core the lens is up to 25 m thick at grades of over 30 per cent zinc. The practice of dividing the orebody into levels and sublevels, with consequent crowns was no longer acceptable because of restrictions in stope design and potential loss of ore. To assist in the development planning of J lens, a geostatistical block model was applied in long section to graphically represent the lens. Areas of high zinc concentration, as well as zones of uneconomic material were identified by using the model. This has meant that the development could he targeted, enabling stope delineation to occur in the lens without significant ore loss. Because of limited development resources, and the need to bring J lens on-line in the near future, the development strategy has had to focus on 'just-in-time' principles, rather than accessing the whole lens from bottom, and progressing upwards. Tight development schedules have required individual stoping block to be developed on such factors as grade and available tonnes rather than as a vertical sequence.

Jan 1, 1993

By Mousset-Jones P, McPherson M. J

Underground airways are characterized by irregular shape and uneven surfaces including large-scale natural roughness, fractures, and a super-imposed sand roughness. Swirls in the grooves of the wall and separation because of the periodic variation of the open cross sec- tion, due to the blasting patterns, make it almost impossible to calculate average con- vective heat transfer computationally on the bases of the geometrical description of the surface. However, dimensionless friction factors can be used to characterize the surface effect of an airway and an analogy between heat and momentum transfer can be applied to calcu- late an average convective heat transfer Coefficient.

Jan 1, 1988

By A Jakowetz

OxianaÆs Sepon Copper Operation (part of the combined Sepon Gold and Copper Operation) is located in Savannaket Province, in southern central Lao PDR. The site is relatively remote, being some five hours inland from the Laos/Thailand border crossing on the Mekong River. The copper processing plant was designed to treat 1.3 Mtpa ROM ore to produce 60 000 tpa of copper cathode. Commissioning of the processing plant was completed in mid March 2005 with ramp up completed in January 2006 with 5260 tonnes of cathode harvested in this month. The focus of this paper is on SeponÆs unique grinding circuit. The entire grinding circuit is operated at highly acidic conditions, adding a number of different operational issues over and above those normally associated with grinding circuits. It became evident early in the ramp up, that reaching design mill throughput of 170 dry tonnes per hour with the original design would be challenging, coupled with the realisation that ceramic grinding media consumption had been underestimated. In order to lift the overall throughput of the processing plant, a significant continuous improvement process has been implemented within the grinding circuit to lift this key unitÆs production capacity. This presentation will focus on the key areas that have been addressed in the 12 month ramp up period and highlight areas for future work. Results to date have shown this improvement process to be very successful, with throughput rates in excess of 200 tph regularly achieved.

Jan 1, 2006