Search Documents

By Dinuzzo P, Wychie J, Desoe C

The Selwyn Gold-Copper Mine is located 150 km southeast of Mount Isa within Proterozoic units of the Mount Isa inlier (Figure 1). Mineralization in the mine area is associated with strongly sheared ironstones and iron rich schists at the base of the mid- Proterozoic Staveley Formation. The ironstone horizons outcrop as a series of dominant ridges over a 10 km strike. Economic gold-copper mineralization has been defined in 4 separate zones within a 3.5 km length of the outcropping ridges. A current combined geological resource for the deposits is 5.3 million tonnes of 5.0 g/t Au and 2.02 Cu. Weathering of the deposits has resulted in a pronounced vertical zonation of mineralogy, especially copper, within the ore zones. This has produced 3 separate ore types which require different treatment techniques. The categorization is based on copper content and zones are termed leached (surface), oxide and sulfide. Ore removed from the pits will be mainly leached and oxidized with minor sulfide near the pits final depths, while the underground ore will be from the sulfide zone with minor oxide in some areas.

Jan 1, 1989

By S J. Chen, N Jiang, Y S. Ding, F X. Li, D W. Yin, F Wang

This study assessed the deformation failure characteristics of rock-coal composites with different height ratios. Uniaxial compression tests were conducted using an acoustic emission monitoring system and XTDIC three-dimensional full-field strain measurement system. The results showed that with the increase in rock-coal height ratios, the uniaxial compressive strength of composite samples increased from 5.26 MPa to 14.61 MPa. The evolution of the deformation localisation zone of the composite samples is closely related to the initiation and propagation of the primary cracks in the coal samples. At the moment when the main fracture of the coal samples occurs, there is a large drop after the peak of the stress-strain curve of the composite samples, and the height of the rock samples increased to varying degrees, which indicated that the failure of the coal samples induced the rebound deformation of the rock samples. With the increase in rock-coal height ratios, the rebound deformation amount of the rock samples decreased from 0.042 mm to 0.008 mm, and the rebound deformation rate decreased from 0.210 per cent to 0.010 per cent. Meanwhile, the rock samples’ rebound deformation releases part of the elastic energy to act on the coal sample, further contributing to the destruction of the coal samples. Compared with single composite coal samples, the coal samples of the composite samples have much more failures. In addition, with the increase in rock-coal height ratio, the input energy density, elastic energy density, post-peak release energy density, and residual elastic energy density of the composite samples increased, the dissipation energy density decreased, and the percentage of pre-peak elastic energy density increased from 98.56 per cent to 99.86 per cent. These results revealed the deformation failure characteristics of rock-coal composite with different height ratios and provided a theoretical reference for understanding the underground dynamic rock failures.

Nov 29, 2022

By Needham RS

Hydrothermal mineral deposits are the dominant mineral deposit type in the Cullen Mineral Field, and have been important sources of tin, tungsten gold, silver-lead, zinc and copper. The deposits are mostly in north to northwest-trend- ing shear zones, and are confined to Early Proterozoic contact metamorphosed metasediments or synorogenic to postorogenic granitoids. The distribution of the vein-type deposits with- in the contact aureole defines a district-scale metal zonation of uranium closest to granitoid, through tungsten, copper, tin, silver-lead to gold with increasing distance from granitoid contacts. This zonation probably reflects de- creasing temperatures within the contact aureole during granitoid emplacement, and at the time of generation of a variety of metal-bearing fluids. A magmatic source for some of the metals is indicated by the positive spatial relationship between uranium, tungsten, copper and silver-lead deposits and granitoids abundant in those metals. There is little evidence for any such relation- ship for tin and gold deposits, except for an association of some tin deposits with tin-enriched mafic rocks. Most of the granitoids with anomalous metal values are late stage highly fractionated leuco- granitic phases forming younger plutons peripheral to the main body of the Cullen Batholith, They probably form cusps connected to the main body at shallow depths.

Jan 1, 1984

By S Q. Zhao, J H. Wei

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Xitieshan lead-zinc deposit is located in the north margin of the Qaidam Basin, Qinghai Province, China. It is one of the largest massive sulfide deposits in China and is supposed to be of the sedimentation-exhalation (SEDEX) type. Based on the main ore mineral and sulfur isotopic compositions in sulfides found in the wall rock, the S of the deposit is considered to originate from the mantle, but the fluid potentially mixed with sea water during the hydrothermal circulation exchange. The study of lead isotopes shows that the metallogenic material is characterised by the mixture of orogenic and upper crust sources. The lead isotopic signature of the wall rock is similar to that of the ore, which shows synsedimentary characteristics. According to the composition of the rubidium and strontium isotopic signature, the value of 87Sr/86Sr is lower than the average value of that in the crustal rock, which is larger than that of the mantle. Hence, the metallogenic materials of this deposit mainly originate from the crust, which is related to materials of volcanic rocks activation and migration of the deep hot circulating water. The process of the metallogenic fluid circulation shows continuous interaction with crustal material and lead to continuous enrichment of the ore forming fluids. From the study of the fluid inclusion microthermometry of the ore and the associated minerals combined with the C, H-O, Si isotopes, it is believed that the metallogenic fluid is mainly coming from the mantle or the deep magma chambers. The rising deep fluid then mixes with the sea water. The carbon dioxide escaping and mixing with sea water during the hydrothermal exhalation process leads to the rapid precipitation of the hydrothermal fluid to deposit metal. That is proposed as the principal formation mechanism of the Xitieshan deposit. Further studies are proposed, including obtaining geochronology data from this deposit.CITATION:Zhao, Z X, Wei, J H, Liang, S N and Zhao, S Q, 2015. Advances in research on metallogenic mechanisms for the Xitieshan sedimentation-exhalation lead-zinc deposit, Qinghai Province, China, in Proceedings PACRIM 2015 Congress, pp 487–494 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By Barro L

There is currently a world wide interest in coal-oil technology as the search continues for alternative energy sources to reduce the consumption of petroleum crude. An important aspect of this coal-oil technology study is to obtain information on the flow properties of coal-oil slurries. While some work has been reported on the flow behaviour of black coal-oil suspensions, very little work on brown coal-oil suspensions has been reported. In this paper flow charac- teristics of brown coal-oil suspensions for various coal concentration and temperatures have been presented. A Capillary rheometer, designed to handle settling suspension, has been used for deter- mining rheological properties. Brown coal of 0 0725 mm average particle diameter has been used in this work. The oil was a coal derived product having a boiling point range of 234¦- 319¦C, Apparent viscosity of all suspensions was found to increase on storage due to ageing. Ageing might have occurred due to physico- chemical interactions between coal and oil. Flow behaviour of some suspensions changed from Newtonian to non-Newtonian on storage.

Jan 1, 1980

The Rio Tinto Iron Ore group currently estimates grade attributes for mineral resources using ordinary kriging (OK). OK produces a smoothed globally unbiased estimate, but does not capture local variability, which can have significant impact on mine planning and scheduling. The dimensions and the multivariate nature of iron ore deposits make point simulations of whole deposits impractical. With a direct block simulation method the size and speed limitations of point simulations can potentially be overcome, resulting in a viable method for capturing local variability and for providing risk measures into the mine plan and schedules. Some iron ore deposits are highly folded (post mineralisation) and require preprocessing using an unfolding algorithm to properly define the continuity parameters and directions of anisotropy before simulation can proceed. Block co-simulation proceeds in unfolded space and since mine planning require a block-model with regular block-sizes; a regular block-model is unfolded first. This paper discusses a block co-simulation approach that can be used to simulate the irregular blocks resulting from the unfolding process. A section of an iron ore deposit is used for testing the block co-simulation algorithm and the simulation results are compared against the Isatis direct block simulation method. Available blasthole data is also used to validate the behaviour of the block co-simulation algorithm.

Sep 26, 2011

By Caelli T, Robey M

Most research into planning of open pit mines has been based on evaluation of volume-element block models in terms of their net present value. The major issues revolve around two interdependent problems the optimum ultimate pit and time-based scheduling. Despite feedback between the two problems, they are usually treated as separate tasks.The ultimate open pit is defined by the removal of whole blocks so that their net present value is maximised. This gives planners an estimate of the total worth of the venture in present terms, and is crucial to obtaining funding. All cost and profit values are assumed to be static throughout the mine life, and the only physical constraint usually taken into account is that of safe, average, wall slopes, which must be approximated by the removal of whole blocks. Modelling of any further constraints (for example, access roads and true wall slopes) is usually achieved by adding them to the optimal pit by hand. Typically this degrades the model by between five and 20 per cent of its value - which then brings into question whether it is still the true optimum.This paper reviews the dominant methods in use for this first task the ultimate open-pit planning problem. Some new optimisations are given, and the algorithms are examined in terms of their efficiency and accuracy. Finally, suggestions are made for improvement of model accuracy and eventual expansion into solutions of the more complete dual problem - that of simultaneously finding the optimum ultimate pits and dynamic schedules for the venture.

Jan 1, 1996

ABSTRACTFor the binary system copper-lead two relationsEquation 1andEquation 2have been derived for the activities of copper and lead at compositions and absolute temperatures within the liquid region of the phase diagram.These relations give, with greater accuracy than is given by previously published relations, the activity-composition temperature variations for all regions of the phase diagram of interest to metallurgists.These relations are essentially simple forms of the Margules equations but with linear temperature dependence applied to their coefficients. This has been done in such a manner that a phase diagram obtained from these relations agrees well with the data available for this system. The methods of obtaining the relations and constructing a phase diagram from them are both given in detail. The enthalpies and entropies of mixing are compared with those derived by other methods.

Jan 1, 1971

By P Waters, P Hollings, M Baker, D R. Cooke

Over the last three million years, porphyry and epithermal mineralisation in the Baguio Mineral District has been driven by calc-alkaline magmatism associated with the subduction of the South China Sea plate and the Scarborough seamounts beneath northern Luzon, Philippines. Coupled with extreme uplift and exhumation rates, mineralisation in the Baguio District has been responsible for the emplacement of over 922 million grams of gold. As one of the oldest intrusive bodies associated with the Baguio District, the Black Mountain Cu-Au deposit consists of at least five intrusive phases overprinted by potassic and propylitic alteration and sulfide mineralisation. Gold ore grades are low and molybdenum grades high with respect to other porphyry Cu-Au deposits in the Baguio Mineral District. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

Japanese pig iron production in 1973 registered about 90 million tons. As clearly seen from the productivity (2.04 t/m3/D), and fuel ratio (494 kg/t-pig), the Japanese steel industry has maintained quite high levels of efficiency in blast-furnace (BF) operations. Among the many factors which have contributed toward these high levels of efficiency, the use of high quality coke is very important. The Japanese steel industry imports about 85% of its metallurgical coals from various countries of the world, including Australia. The effective use of these metallurgical coals of various origins in accordance with their re- spective properties is most essential for maintaining coke quality. This paper describes coking properties of various metallurgical coals and blending techniques based on these coking properties, in relation to the specifications of coke quality required for efficient BF operations. This paper also describes briefly new technology for expanding the scope of the use of coking coals.

Jan 1, 1975

The phenomenon of Instantaneous Outbursts, although not new to Australia, was sharply drawn to the attention of the local coal-mining industry by two isolated fatal occurrences on widely separated fields, both late in 1954. An outburst is the eruption of apparently solid coal from the face, aided by vast quantities of gas released from the coal, as the coal fails under mining stresses additional to its natural stressing.The gases involved are principally methane and carbon dioxide. The various factors which combine to produce outburst conditions range from external factors such as stresses arising from depth of cover and other causes, to inherent factors such as strength of coal,and its capacity to retain gases (sorption). Of the localities where instantaneous outbursts occur the Gard Basin in Southern France has had the greatest number and the most serious occurrences. By contrast, local outbursts have been minor.Experimental work into some influencing factors has been carried out by various overseas authorities and some research has been accomplished in Australia. Practices used in some overseas areas to improve safety of working are largely empirical, as are the local rules and recommendations for work in affected areas.The appearance of further outburst areas is anticipated as mining becomes more extensive and deeper.INTRODUCTION"Instantaneous Outbursts" can be described as violent eruptions of coal from the solid accompanied by considerable gas evolution. The projected coal is usually of small size, and a high proportion is pulverized, and may be carried and deposited over great distances by the gases, liberated from the outburst. This outburst coal is of bituminous to anthracitic rank, and the gas involved is essentially methane or carbon dioxide, or a mixture of both. Outbursts involving carbon dioxide are usually more violent and dangerous. The phenomenon is relatively unusual, being confined to probably sixteen known areas in the entire world, these areas comprising only portion of the coalfields in which they occur. Usually only one or two mines on each field are affected.

Jan 1, 1958

The Hall-Hoult process is likely to be the dominant method of aluminium production for the remainder of the century. The characteristics of the operation of a modern smelter are described and attention drawn to their disabilities which are due chiefly to the small production capacity of individual cells.The principal components of the Hall-H6roult cell - the electrolyte, the anode and the cathode - are discussed in order to identify the problems of scale-up. The factors influencing current efficiency and energy consumption are analysed and lead to the conclusion that the greatest potential for energy saving lies in reducing the anode to cathode distance (ACD).The most promising direction for major change is in the application of a new titanium diboride - carbon composite for coating of the surface of the cathode carbon. It improves the wetting of the carbon by aluminium and should permit the use of sloping cathodes and anodes. The deep metal pad would thereby be eliminated and, in the absence of magnetic perturbations, the ACD could be substantially decreased.The construction and testing of a full-size "Low Energy Cell" is scheduled for early 1986 and is expected to reduce energy consumption in aluminium production by about 15%.

Jan 1, 1985

Attention is drawn to the largest eruptions with dense rock equivalent (D.R.E.) volumes approx-imating 50 km3. These have been strongly clustered during the last 40 000 years, with 11 recognised in the period 35 000 to 22 000 years ago, and 10 in about the last 9000 years, but none in the period 22 000 to 9000 years ago. With the latest such eruption, at Tambora, only 175 years ago, it is likely that we remain in a period of increased activity. During the last 100 000 years, roughly the period during which modern Homo sapiens has existed as a species, there has only been one eruption an order of magnitude larger (>_ 500 km3 D.R.E.). This took place at Lake Toba, Sumatra, about 75 000 years ago, and is estimated to have deposited ash to a thickness of a centimetre or so in parts of Ethiopia, Somaliland, Saudi Arabia and Iran, and to a thickness of a few millimetres in the eastern Mediterranean. The average interval between global eruptions of this magnitude is probably about 40 000 to 50 000 years. Insufficient work on the Quaternary history of volcanoes has been carried out to suggest where the next such eruption might occur. At Yellowstone, which has been well studied, the average interval between very large explosive eruptions is about 700 000 ¦ 120 000 years.As a prerequisite for magnitude-frequency analysis of eruptions, and hazard and risk impact assessments, it is important to classify past eruptions in a consistent manner. In an attempt to find a universally applicable method to estimate order of magnitude D.R.E. volumes from the distribution of airfall tephra, an empirical correction has been derived for the elongation of tephra dispersal fans due to wind. Dispersion distances for various thicknesses of tephra, recalculated for windless conditions, have been obtained from a study of about 40 tephra isopach maps for which D.R.E. volumes have been calculated, and a range of distances derived, equivalent to D.R.E. volumes from 106 m3

Jan 1, 1990

By F Sinaga, E Widijanto

PT Freeport IndonesiaÆs Deep Ore Zone (DOZ) mine is the new underground block caving mine within the East Ertsberg Skarn System (EESS) which started production in mid-2000. The DOZ will produce 25 000 tpd using mechanised block cave mining method and will be the fourth underground mine opened within the EESS deposit. A review of the DOZ extraction bolting design was conducted in November 2000. The aim of this review was to re-evaluate the effectiveness of the current design in relation to bolt length and spacing and to challenge some questions about the technical background of the design. For instance, the influence of the rock condition on the design. To review this bolting design, several books and papers are reviewed and several experienced people have been contacted to give their opinion. The methodology used for this review is:reviewing the technical background of current design; collecting ideas and alternatives; collecting data from books and personal communication and conducting analysis; and conclusion and proposed design.

Jan 1, 2002

An underground storage and filling distribution system is presently being established at North Broken Hill Limited in the No.3 Shaft area. This has been necessitat- ed by the dependence of the present filling system on the No.2 Shaft and its imminent closure due to cessation of production. The storage will consist of three tanks excavated in low grade ore, between the No.20 and No.21 levels, at approximately 2700 feet below the surface. The tanks will each have a capacity of 1500 cu yds. Consideration was given for surface storage, although under- ground storage was thought to have greater merits. Two tanks have been excavated, and are in operation. Three or more outlets are installed beneath each tank, with horizontal connections into the No.21 level 'mixing box'. Water decants from the top of the fill in the tanks, and passes into a decant water sump, at the bottom of which is a borehole to the No.21 level. This is then connected to the mixing box and water used as make-up water with the semiwet solids for transport into the existing pipe distribution system. Preliminary results of the system have been satisfactory and it is envisaged that this system will readily cope with the filling demands of the future.

Jan 1, 1973

By P A. Jenkins, I W. O Jones

WMC has mined the Perseverance disseminated orebody exclusively by SLC (sublevel cave) methods. Deteriorating ground conditions in the vicinity of an orebody inflection forced a re-evaluation of future mining at Perseverance and a strategy to drop down below the inflection zone and recommence the cave was implemented. This strategy has led to increased production at higher grades, resulting in lower costs and better mill recoveries. This paper describes the evolution of mine planning, development, support and production strategies through the successful process of implementing the ædrop-downÆ and re-establishing the SLC.

Jan 1, 2000

Newmont Australia Limited has for some 15 years mined a number of large open cuts associated with the Telfer Gold Dome deposits. The principal ore body exploited has been the East Flank of the Main Dome where a very high grade gold reef deposit of mixed metal sulphides, grades in excess of 20gA Au, has been mined in conjunction with dissemi- nated mineralisation contained in the overburden material. The main ore body has been under review for some years as an under- ground mine, however due to the ore body widths of less than 1 metre and a dip generally less than 35 degrees and a very weak host rocks earlier studies all resulted in a continuation of open pit mining activities. In early 1988 it was recognised that open cast mining would not be able to mine all of this valuable resource and a feasibility study was commenced to come up with a practical and economic approach to underground mining.

Jan 1, 1991

By Haskard R. W

A method of raising has been developed at Cobar Mines Pty Ltd's CSA Mine which has achieved advance of up to 6 m in a single blast and raises are now developed which have averaged 4.2 m per blast. The method is a form of Long Hole Raising and is applicable to short raises of less than 50 m length. Blast holes are column charged and initiated sequentially with short delay detonators (millisecond). The equipment used to drill the raising blast holes consists of normal production drilling rigs and accessories and no other special equipment is required. The method has significant advantages in rates of performance and fits neatly into production drilling and blasting schedules. The method is also far safer than any non-mechanical or conventional means of Raising.

Jan 1, 1983

By Schmidt CG

Parameters affecting gold elution using the AARL process are reviewed and critically analyzed in an attempt to optimise metallurgical efficiency and minimise costs in both current and future carbon adsorption operations. Such factors as acid washing, column geometry, elution temperatures and pretreatment reagents are discussed together with eluant water quality and eluate flowrates. Hot acid washing of carbon prior to gold elution has many benefits. Besides improving elution efficiency when eluting with regional water, a hot acid treatment preheats the carbon without causing any gold leakage. Laboratory data indicated that hot acid washing reduces the mass loss of carbon during thermal regeneration. The eluate going to either zinc precipitation or electrowinning is also relatively free of troublesome impurities (organic contaminants and ferrocyanides in particular). Because of the chromatographic character of the AARL elution where an ionic strength gradient is used to inhibit the readsorption of gold, column geometry plays a significant role. While practical considerations and capital costs may restrain the length of the elution column, high length/diameter ratios are advocated in order to promote the plug flow of column eluate. From both a metallurgical and costing viewpoint, the two significant factors affect- ing the AARL gold elution are temperature and cyanide addition. High temperature and high reagent additions within prescribed limits will improve metallurgical efficiencies, but a balance between energy and reagent costs is required in order to minimise overall elution costs. As pretreatment reagents constitute a considerable portion of the total elution costs, both the addition and consumption of sodium cyanide must be carefully considered. Lower cyanide additions may be effective in certain instances, but the more practical use of 0,6 bed volume of a 2-3 per cent NaCN reagent containing 2 per cent NaOH is advocated. This is equivalent to an addition of 20-30 kg NaCN and 20 kg NaOH per ton carbon Treated.

Jan 1, 1986

By Wickham P, Raeburn M. R

The design and development of slurry sampling equipment for the Mount Isa Mines Limited on stream analysis installations is discussed in detail. Emphasis is given to the critical areas of slurry transport, screen design, pump selection, elimination of fast wearing components and maintenance reduction. Sample point design to fulfil the specific accuracy requirements for On Stream Analysis (3% to 10% relative) is discussed.

Jan 1, 1976