Search Documents

By F C. D Michelin

Blast fumes are a significant health risk to underground workers, containing several dangerous gases such as carbon monoxide (CO), nitrogen oxides (NOx) and ammonia. To ensure safe working conditions, workers are not normally allowed to re-enter a mine until the gases are cleared. To predict if gases can be cleared efficiently, simulations can be performed to estimate the gas levels following a blast. For accurate modelling, a calibrated airflow simulation is required in addition to blast-specific parameters such as the yield rate (representing the amount of gas released per kg of explosive) and the dispersion factor (representing how quickly the gases can enter the air stream from the explosive site). Those parameters are not easily determined, as they will vary from blast to blast. Many post-blast gas recordings on mine sites were studied and the correct parameters were determined to ensure an accurate gas simulation. The variability of the results was then analysed and correlation to known parameters is suggested. Finally, recommendations on how to determine the correct parameter are presented.

Oct 12, 2022

By P Myers, T Elkington, S Wonday

Sierra Rutile LimitedÆs (SRL) heavy mineral sand mining operation in Sierra Leone, West Africa, is embarking on a new phase of its life. After confronting many challenges during the 1990s and 2000s, SRL is embarking on a strategy of growth to recover maximum value from the mine over the rest of its life. Sophisticated linear programming techniques have been used to develop an optimum strategy for extracting SRLÆs many known deposits of economic grade, while considering options for expansion and for a variety of mining and processing methods and combinations. CITATION:Myers, P, Elkington, T and Wonday, S, 2012. Strategic optimisation at Sierra Rutile - A case study in maximising project value, in Proceedings Project Evaluation 2012 , pp 59-66 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 24, 2012

By Christie GB, Mainwaring DE, Leong YK

High solids brown coal slurries have been prepared with concentrations approaching those achieved with bituminous black coals. The high inherent water content and macroporosity of Victorian brown coals have been reduced in a controlled manner by chemical and mechanical means. The hydrophobicity of the coal surface has been increased sufficiently to reduce the tendency for swelling and water uptake. This together with densification has allowed the solids content to be progressively improved from 25% solids with raw coal to 65% solids with modified coals. Both raw brown coal and modified brown coal suspensions show shear thinning behaviour resulting in lower viscosities at higher flow rates. All coal suspensions displayed a yield stress once sufficient solids concentration was achieved. This yield stress can be used in the prevention of solids settling. Under simple shear mixing the network structure that provides the yield stress quickly breaks down to a low viscosity fluid with reduced yield stress and a pumpable consistency. The time necessary for structural recovery is in the order of days permitting shut-down and start-up of fuel delivery systems.

Jan 1, 1987

Beach sands on the Morobe coast of New Guinea contain significant amounts of chromite. This chromite, together with the more abundant associated minerals such as olivine, enstatite, tremolite, antigorite and feldspar has been de- rived from rocks of the Papuan Ultramafic Belt and transported to the beaches by three rivers, the Paiawa, the Saia and the Sesimbai. Of the hundreds of samples taken, 26 have been analysed mineralogically and chemically in some detail. On this basis, five groups of samples, four on- shore and one offshore, representing character- istic mineral assemblages, have been recognized. The chromite grains themselves have been exam- ined to determine variations in amount and in the Cr/Fe ratio, since this is of economic importance. Much of the chromite fails to reach a high Cr/Fe ratio as a result of magnetite rims around chromite grains. The precious metal content of the sands is negligible.

Jan 1, 1973

The objectives of mining grade control are presented and examples of the techniques used in various open pit and underground mines are used to define the attributes of good grade control. Reasons are discussed for the success of various improved practices. The progressive development of grade control is presented and the balance between quantitative and qualitative data is analysed. The skills and resources required for grade control on mine sites that are using best practice are also presented. A number of problems in grade control have been solved recently however there are still issues that need to be addressed. Examination of the grade control process frequently stops after sample quality has been examined. There is much more beyond this that can now be optimised using conditional simulation models. Other future directions of mining grade control are also suggested. An extensive bibliography of published papers on grade control is included that will be maintained and updated on a website.

Jan 1, 2000

By Misra A

After review of the status of research on optirnisation of retreat longwall faces it is argued that an acceptable optimisation model must be based upon realistic cost data that take into account not only the face costs, but the total panel costs. These include the cost of development, face cost, removal and installation cost. The determined optimum length of a retreat longwall face is based upon a realistic model and actual costs.Parameters that influence the optimum face length have been varied over wide limits to allow determination of the sensitivity of the model and the effect of the parameters on the optimum face length. It is concluded that for medium production rates and medium system availability, the optimum face length of a retreat longwall face under Australian conditions lies between 180 and 220 metres.

Jan 1, 1995

By P Jere

Mechanically coupled rock bolts encapsulated in cementitious or polyester cartridge resin grouts have been widely adopted for various underground rock reinforcement applications. Resin grouts are considered a superior product, however, both systems have their advantages and limitations, with the relative performance, quality installation cost and cycle time as the most notable parameters. Both applications have optimal rock bolt combinations and preferred ground conditions. Cementitious grouts are favourable for use with secondary deep embedment anchors. These are installed using various equipment with a series of autonomous tasks required to complete the installation cycle. The cartridge resin system can be utilised by a bolting or face boring rock drill to complete the full support installation cycle. This reduction in equipment changeouts mid-cycle generally deems it the more practical application and popular choice for primary support. Self-drilling anchors (SDAs) and hollow bolts have been a viable alternative to traditional rock reinforcement in variable and challenging ground conditions. Using a pumpable post installation grouting system, SDAs have proven to aid the quality of installation, but due to the additional equipment and cycle steps associated with application, the cycle time is increased. In recent years, fully mechanised bolting equipment designed to utilise a combination of self-drilling anchors and a thixotropic pumpable resin installed in a single pass has entered the market. This innovation is anticipated to deliver the advantages described above, with fewer limitations, and significantly improved development and rehabilitation rates. St Barbara Mining and Byrnecut Australia, supported by Master Builders Solutions, were first to conduct extensive trials and implement this rock bolting approach in an Australian hard rock underground mine and record the actual performance.

Mar 29, 2023

By M P. Sandy, R M. Stephenson

Portals to access underground mines are important infrastructure and their design requires careful consideration. Portals are generally expected to last for the life of the mine. Typically, the exposure of personnel and equipment is high, with many hundreds of movements through the portal per day. Consequently, the risk associated with geotechnical instability must be extremely low. Portals are often established from a boxcut. In areas where the weathering profile is well developed, the design and execution of the boxcut can involve significant effort, with the objective of minimizing the volume of the boxcut, whilst ensuring that conditions at the design depth are suitable for establishing a stable portal. Properly designed site investigations are a critical part of this process. Currently available portal design guidelines have not been updated for decades, however the equipment and ground support systems have changed significantly in recent years. Many mine portals have since been constructed in a relatively short time frame with success, often in challenging ground conditions using some of the more modern approaches to ground support. This is beneficial because delays in establishing a portal will generally delay other critical path activities, and lead to cost overruns.

Mar 15, 2021

By R Barritt, P Scott, K Albano

Successful closure of tailings storage facilities (TSFs) is an environmental issue faced globally by metalliferous mines. During the initial feasibility and design phase of the mine life importance is placed on the physical stability of above ground TSFs, largely driven by legislative requirements, whilst closure planning is often a secondary consideration. However, as the landform is further developed and constructed attention must be paid to regularly revisit the original closure plan and update it to achieve the best (sustainable) possible outcome for both the environment and stakeholders. A mine in northern Queensland is in the process of developing a closure strategy at their TSF. Appropriate closure measures for the TSF are required to mitigate the impact of any seepage emanating from the TSF on the groundwater and surface water receptors. O’Kane Consultants Pty Ltd (OKC) have provided the mine assistance with the development of a TSF cover system design in order to appropriately manage tailings during operations and to prepare for the facilities’ closure. OKC has collected data since 2007 from cover system field trials located on the TSF. To enhance engineering judgement in the design of future cover systems, calibration of soil-plant-atmosphere numerical models to field data (referred as ‘field response modelling’) were completed. Calibrated model inputs can be used to provide insight into long-term cover system performance as well as a tool for design of the final landform.Following a site investigation, materials characterisation and numerical modelling program various cover system alternatives were developed. Two of the preferred cover system alternatives referred to as Test Plot #1 (TP#1) and Test Plot #2 (TP#2) (Figure 1), were constructed at the site and instrumented. Monitoring instrumentation comprised several nests of in situ volumetric water content and thermal conductivity sensors to measure changes in water content, temperature and matric suction within the cover system materials and underlying tailings waste. Run-off collection buckets and a fully-automated meteorological station were also installed. CITATION:Barritt, R, Albano, K and Scott, P, 2016. Findings and conclusions following ‘long-term’ cover system monitoring – refinement of the conceptual design for tailings storage facility closure, in Proceedings Life-of-Mine 2016 Conference , pp 85–88 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

Polish coal mines are well equipped with methane monitoring systems,nevertheless the worsening conditions force a continuous impro- vement in the field of environmental monitoring. Application of modern electronic components make it possible to design the new modular telemonitoring system incorporating the best features of the older systems,widely employed in Polish collieries, eliminating their weak points. Several new sensors and portable instru- ments for methane monitoring and early fire detection have been developed and tested in mining conditions.

Jan 1, 1988

By G R. Ballantyne, A N. Mainza, M S. Powell, M Evertsson

Quantifying the performance of a comminution circuit relative to the potential that can be achieved is a standard requirement in justifying operating practice (the stick) and seeking operational upside (the carrot). Historic measures tend to focus on performance relative to laboratory design tests that provide a direct measure of specific grinding energy, such as the Bond Work index; or use dropweight breakage tests calibrated to a substantial database of operating sites, such as the SMC methodology. Although of value, such approaches are flawed in significant aspects. The assumption is that the laboratory prediction is correct and the single sample it is based on is representative. The database benchmarking methods are, by definition, locked into current average operating practice. These approaches do not illuminate upside; can ‘punish’ operations that are actually more efficient, such as grinding finer than standard operation; and reward poor operation that may comfortably produce a coarser grind than optimal for recovery or excess slimes that reduce recovery and increase water consumption and tailings volume. The authors present a set of established and easily applied measures, that draw together daily operation, highlight areas of opportunity and inefficiency, use simple samples and data, and can be used to provide the ‘size of the prize’ in pursuing specific areas of process improvement. These tools include size specific energy (SSE), overall operating effectiveness (OEE) which includes product quality, theory of constraints, and links this to the end objective – maximising the efficient production of valuable metals. Feeds into objective function driven by economics – financial return, energy, environment.

Aug 24, 2022

By S S. Kanchibotla, I Brunton

Most blast fragmentation models assume the rock mass properties, explosive properties and blast design variables to be constants and uniformly distributed within a blast. However, in reality all these input variables vary within a blast resulting in variation in the resulting fragmentation size distribution. A stochastic modelling approach is introduced in this paper to quantify this variation. This technique takes the input variables as statistical distributions rather than constants and through several thousand iterations, generates a statistical representation of the expected fragmentation resulting from a production blast. A case study of three production blasts from a large open pit mine are presented and the modelled fragmentation æenvelopeÆ shows good agreement with the fragmentation æenvelopeÆ estimated from Split image analysis. The various blast-related parameters influence different parts of the fragmentation distribution, eg rock strength and explosive velocity of detonation have most impact on the fines. The technique is used to identify the parameters that have the greatest influence on various size fractions. Such an analysis will be useful to direct resources to efficiently minimise the variation.

Jan 1, 2001

By G Fergus, M Hart, S W. Weeks

Rio Tinto Alcan has undertaken feasibility level assessments into the expansion of its bauxite mining operation in an area south of the Embley River in far north Queensland. The project has the potential to extend their Weipa operations by approximately 40 years.The construction and operation of two additional mineral ore processing plants are proposed for the South of Embley project. Golder Associates was engaged to develop and conduct modelling assessments of potential sources of water supply required by mineral ore processing.Two models were developed using GoldSim: a dam yield model and a water balance model. GoldSim is a graphical object-oriented modelling environment with a capacity to carry out dynamic probabilistic simulations. Originally developed by Golder, GoldSim has been applied successfully in a decision support role to a range of mine water management operations.The dam yield model was used to provide estimates of reliability and volume of annual water supply of several potential surface water dams. This information was then used to determine a hierarchy of water supply options for processing plant operations. The water balance model dynamically simulated the water demands of the two production plants and the consequential response in water supply, with respect to the timing and discharges provided by the various source options.Use of the model provided a preliminary operational tool to assist with water supply management decisions. Water quality issues required a blending of water from separate sources and attention paid to scheduling to ensure water supply through the dry season. The model also helped identify risks to water supply in the event of underperformance of one or more water supply sources. This allowed the operational rules to be refined to minimise those risks.The dynamic and stochastic modelling approach provided a method for identification of water supply issues susceptible to seasonal climate variability.CITATION:Weeks, S W, Hart, M and Fergus, G, 2013. A dynamic evaluation of water supply security susceptible to climate seasonality, in Proceedings Water in Mining 2013, pp 197-208 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

By P V. A van der Westhuyzen

Namakwa Sands is a heavy minerals mining and beneficiation business in the Exxaro Sands Division, and operates along the West Coast of South Africa (see Figure 1). The business encompasses mining, mineral concentration, separation, and smelting operations. Inflated commodity prices and increasing operating costs demands greater attention to the management of process performance and the company wide coordination of resources. Consequently, the task of deploying operational/technical skills and budgets into the most appropriate parts of the business assumes great importance in order to increase productivity from its capital assets. The mineral sands industry is under the same sort of economic scrutiny that all other industries find themselves, and as such, Exxaro – Namakwa Sands has taken the strategic initiative to improve overall resource utilisation within the processing steps and to measure the costs associated with obtaining this value.This paper provides details of the successful implementation of a Kelsey Centrifugal Jig (KCJ) at Namakwa Sands to recover primary and secondary zircon products from the wet gravity (quartz) rejects generated and stockpiled at the Mineral Separation plant (MSP).

Oct 5, 2011

By I Swane, R Rait, A Robertson

Geochemical assessment of mine waste materials prior to commencement of a proposed mining operation is a fundamental component of mine feasibility studies and the regulatory approvals process. Static and kinetic geochemical test methodologies are widely used to predict the geochemical nature of mine waste materials and to develop strategies for managing potentially æhostileÆ materials. These data can also be integrated with data from other fundamental studies such as hydrogeology to predict specific environmental outcomes and potential impacts at mine closure and post-closure.A case study is presented for a proposed open pit gold mine in Mongolia, which illustrates how geochemical, hydrogeological and groundwater quality data can be used as part of a geochemical modelling process to predict the final pit lake water quality over time. A series of static and kinetic test geochemical test programs were completed and acquired data integrated with hydrogeological and groundwater quality data provided by the proponent. A widely used geochemical modelling program (PHREEQC) was used to develop the geochemical model and predict water chemistry in the pit void after mine closure. Sensitivity analyses were completed to explore the effects on the model output of groundwater to leachate water ratio, pit wall rock type and climate.Modelling has indicated that pit void water should be pH circum-neutral at mine closure and should remain within Mongolian and World Bank water quality guideline limits under the modelled simulation most likely to occur in the field. Final void water salinity is expected to increase eight fold over 14 years after end of mine life due to a continuous flux of salts (particularly sulfate salts) into the pit lake whilst the pit lake volume will remain relatively constant due to evaporation and a slow recharge rate. Dissolved metal and sulfate salt concentrations in pit water are also predicted to increase over time and could be moderately elevated compared to applied water quality guideline values. Some of the metal concentrations, however, may be lower as these would be expected to precipitate at circum-neutral pH and greater. Recommended additional assessment work on the project when mining commences includes determining the magnitude of adsorption and co-precipitation of metals occurring in the pit void water/sludge system.CITATION:Robertson, A, Rait, R and Swane, I, 2013. Geochemical assessment of mine waste materials and prediction of final pit lake water quality at a proposed gold mine in Mongolia, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013 , pp 165-170 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 29, 2013

By M Habte

This paper presents a simplified method for the assessment of creep deformations in rock masses containing bands of low strength or soil strength rock. The main impetus for this work was the need to assess the impact of distinct bands of clay and/or low strength rock on the long term deformation behaviour of a rock pillar formed as part of a series of proposed tunnelling works. In particular, the authors were interested in being able to provide criterion which could be used by site personnel to assess the encountered rock conditions against design assumptions.Creep deformation versus time plots are presented for a range of material consistencies. These plots were produced using the hyperbolic creep equation proposed by Mesri et al (1981). This empirically based equation was chosen for its simplicity and practicality. Discussion is included regarding typical input parameter values and the sensitivity of the results to these values is explored. Finally, in the soil strength materials, the secondary consolidation equation is used to check the veracity of the results calculated using the hyperbolic creep equation.

Mar 8, 2011

By S J. Kim, S W. Kim, L Tomas da Rocha, S Jung

Al2O3 has been regarded as a harmful gangue component in iron ore, especially causing reduction degradation in industrial sintering of iron ore. The current study aimed to utilise low-grade iron ore containing high Al2O3 content in sintering process. In order to counteract the adverse effect of Al2O3 on reduction behaviour of iron ore sinter, mill-scale and calcined dolomite were chosen as FeO- and MgO-bearing materials. Firstly, mill-scale was added to high Al2O3 sinter and addition was optimised as 10 wt per cent, then calcined dolomite was added further. Magnetite and magnesio-ferrite were identified as the major phases in iron ore sinter when adding mill-scale and calcined dolomite. As the dosage of calcined dolomite increased beyond 4 wt per cent of in sinter mix, unreacted MgO particles were observed, which is ascribed to the limitation of MgO dissolution into magnetite matrix. Both mill-scale and calcined dolomite were effective in improving compressive load and Reduction Disintegration Index (RDI) of iron ore sinter although its reduction degree was highly decreased. The addition of both FeO and MgO-bearing materials to high Al2O3 sinter has a potential to improve the sinter quality, also contribute to the recycling of industrial by-product. However, the amount should be optimised in views of phase development and deterioration of reducibility.

Jun 19, 2024

By F F. Pitard

The optimisation of a metallurgical plant requires two kinds of sampling systems. The first provides samples to follow process changes, so in due time actions to maintain key parameters within pre-established specifications can be applied. The second provides composite samples at the end of a working shift to demonstrate that valuable constituents sent to the plant went to either a final concentrate or to the tailings in a logical, expected proportion. Contrary to what many experts may claim, these two kinds of sampling requirements are incompatible and cannot be fulfilled using the same sampling systems; this is because the required samples have completely different objectives. A process control sample is an instantaneous sample with increments taken at short intervals, and the objective is to know where the process is at any given time. Excellent accuracy is not a must, however good precision is recommended since a possible process correction may need to be made. Online analysers fed with in-stream stationary cutters or other kinds of in-stream or by-stream probes can do well for such a mission. A composite sample for metallurgical accounting with increments collected over a long period of time, for which excellent accuracy and good precision are both required, must be generated by sophisticated and extremely well-maintained cross-stream sampling stations. The use of process control sampling systems to achieve good metallurgical accounting has been promoted by several manufacturers of sampling equipment around the world; it is a grave mistake that is misleading top management and a practice that should be scrutinised and preferably eliminated. Furthermore, bias tests used to prove otherwise are often based on insufficient data to draw valid conclusions; a guideline is provided.CITATION:Pitard, F F, 2014. Sampling systems for process control and metallurgical accounting, in Proceedings Sampling 2014 , pp 25–32 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 29, 2014

By Oda Y, Hashiuchi M

In the smelting section, flexible fuels such as coal or coke are used in place of heavy fuel oil in order to utilize energy sources more efficiently. Heat recovered from the off gas of the furnace has been converted by the waste heat boiler into steam, which is used for self power generation and for heating or maintaining various temperatures. The amount of the recovered steam in the smelter is currently increasing due to maximum utilization of powdered cokes. The heat source required to maintain the temperature of the electrolyte in the tank house is electric power and steam. However until recent year this steam was provided by its own heavy oil combustion type boiler in the tank house since the amount of steam consumed in heating the electrolyte is large. Though experimental work over the last few years has shown the advantages of reducing steam in the tank house by fully covering the cell, the implementation of the full cover can lead to other operating problems. However various improvements, mainly the covering of the cell with a simple device, have led to greatly reduced steam consumption. As a result, steam for the tank house is now provided by the waste heat boiler only bringing more efficient energy usage.

Jan 1, 1987

MIM Holdings Limited has acquired a reputation for the successful application of R&D to develop break-through technologies for the mining industry. The Isa Process tank-house technology has been licensed to copper refineries throughout the world, and almost 40 per cent of the worldÆs copper is refined using this technology. Isasmelt copper and lead smelting technology is either in use, or is currently being installed, by eight companies in eight countries around the world. Jameson Cell technology is widely used in the coal mining industry and increasingly in the base-metal industry. The IsaMills developed at Mount Isa and McArthur River made it possible to develop the McArthur River and George Fisher orebodies. This paper will address the need for innovation and then discuss the development of the IsaMill and Isasmelt technologies. It will conclude with some comments about why MIM has been so successful in developing such technologies.

Jan 1, 2002