Search Documents

P. W. BRIDGMAN.-Owing to a misunderstanding, I did not see Dr. McAdam's and Dr. MacGregor's remarks on my paper on Flow and Fracture (Metals Technology, December 1944, Pp. 32-38), until after their publication. Both Dr. McAdam and Dr. MacGregor speak of my analysis for the stress distribution at the neck of a tension specimen as containing several assumptions; in particular, that the strain is uniform across the section of the neck, that there is no hoop tension at the periphery, and that the plasticity conditions of von Mises hold. As far as the mathematics goes, the situation is no different in this problem of plastic flow than in a conventional problem of elasticity. That solution is unique which satisfies the boundary conditions on the stresses, the stress equations of equilibrium, and in addition the constitutive equations connecting stress and strain in the elastic case, or a corresponding set of equations, of which the von Mises relations are a special form, in the plastic case. In the particular case of the necked tension specimen I have found that there is a solution satisfying the boundary conditions, the stress equations of equilibrium, and the von Mises plasticity conditions in which the strain is uniform across the section, and there is no hoop tension at the periphery. This is therefore the solution, and the uniformity of strain and vanishing of hoop tension at the periphery are to be described as discoveries, over which the operator has no control, rather than as assumptions. The only part of the solution that can properly be described as an assumption is the von Mises plasticity condition. With regard to this it is to be noted that the condition is needed only in a much weakened form, for the analysis uses the condition only at the neck, where the strain is approximately constant. Thus, in the extreme case referred to in a footnote of my paper (p. 37, Met. Tech. Dec. 1944) the actually measured strain across the section varies from 2.4 to 2.6. Obviously it is a much weaker assumption to postulate that the von Mises condition holds in the strain range 2.4 to 2.6 than to assume it to hold for the entire range of strain from o up to 2.6, which would be necessary if the solution applied to the entire tension specimen rather than to the immediate region of the neck only. Furthermore, it is to be commented that under the special conditions of this problem the von Mises condition becomes identical with the maximum shearing-stress criterion of plastic flow; this amounts also to a weakening of the restrictions imposed by the von Mises condition. Dr. MacGregor refers to actual experiments of his own in which the strain was found not to be uniform across the neck. It is to be emphasized, however, that these were experiments on bars of rectangular section, and that the nonuniformity established was a nonuniformity around the perimeter, not a nonuniformity from the surface toward the axis. My method of solution applies only to a circular cross section. It can be said that the solution that satisfies the boundary conditions, etc., would definitely not be expected to demand a uniform strain for noncircular sections. In discussing my results, Dr. McAdam uses a definition of "flow stress" different from mine, so that the immediate applica-

Jan 1, 1945

By O. G. Lellep

IN every country economic circumstances prescribe the method used to produce a commodity at lowest cost. In Pennsylvania a man's wages for working 4 hr buys a ton of coal wholesale; in Germany a laborer must work 40 hr, or ten times as long. In western Europe, therefore, conservation of fuel is of primary importance, and recent practices of burning lime and cement differ from those employed in the United States. This paper presents data collected during a trip through western Europe in 1953. Considered uneconomical, shaft kilns for burning cement disappeared in the United States two generations ago. But because required capital investment is low and operation greatly improved, shaft kilns are still used to some extent in Europe, where fuel costs are high, and are even included in designs for plants under construction. During the last 50 years shaft kilns have been maintained at the same physical size, while their output has been increased at least four times.

Jan 7, 1954

By William Paxton Hewitt

Mineral deposits of western Utah and eastern and central Nevada have produced in excess of $8,500,000,000 since 1871. Through 1965, Bingham Canyon had produced over $4,600,000,000 and seven other camps over $100,000,000 each, principally from base metals. In addition, they yield iron and uranium ores; contain the world's largest beryllium reserves; and have produced the United States' most important gold discovery in 25 years. The area is famous for its silver production and its bonanza-type precious metal deposits, but such production has become unimportant. The area's greatest producers of metallic wealth are base-metal deposits in limestones and porphyry-type copper ores. In contrast to silver's decline, gold production has been rising-the result of by-product operations at Bingham Canyon. The area also contains gold deposits in which the gold is so finely disseminated it is not recoverable by panning. The area's gold ores frequently are associated with realgar, cinnabar, and carbon. The ore deposits generally are attributed to Tertiary intrusives,* but, at Mountain City, they may be related to Paleozoic volcanism. Mountain City has yielded rich chalcocite from quartz-pyrite-chalcopyrite bodies in siliceous sediments. Regional stratigraphy and structure are difficult to interpret, 69 per cent of the area being obscured by alluvium or volcanics. In general, central Nevada consists of chert, shale, silty sandstones, lavas, and pyroclastics; eastern Nevada and western Utah of many alternations of limestone, shale, and sandstone. Central Nevada has been structurally active since late Devonian. Although granitic stocks may have intruded eastern Nevada and western Utah prior to the Cretaceous, these areas remained quite stable until affected by the Laramide Revolution. Precambrian exposures, occupying 3 per cent of the area, have not been important hosts. However, the question is raised as to whether Precambrian carbonates, properly situated with respect to invading mineralizers, might yet prove to be important. This paper describes 16 precious metal camps, 6 limestone replacement districts, 2 silver-base metal vein deposits, and 9 miscellaneous types and discusses briefly the 11 * Some ores, as at Ely, are associated with intrusives of. Cretaceous age. major camps that are described in detail in this Volume.

Jan 1, 1968

By B. S. Butler

PART I SUMMARY CERTAIN relations between the formation of ore deposits and other geological processes are pretty generally accepted, namely: that many ore deposits are closely associated with igneous activity; that ore deposits accompany certain types of intrusive bodies, notably batholiths and stocks, and that they are concentrated near the tops of such bodies; that igneous activity occurs in belts of strong folding and faulting; that folding and faulting are greatest in basins of extensive sedimentation and least in areas of erosion or slight sedimentation; that areas of erosion or slight sedimentation and of heavy sedimentation persist over long periods and exert a major control over structure, igneous activity, and ore deposition; that cycles of erosion, deposition, folding and faulting, igneous activity, and ore deposition, have been repeated through geologic time resulting in rather definite periods in which metal deposits have formed. In short, ore deposition is but one phase of a series of closely related geological events. It is attempted in this chapter to point out the relations of these interreacting geologic processes to the distribution of ore deposits in the western United States. Three great periods of mineralization are recognized; pre-Cambrian, post-Jurassic, and late Cretaceous-Tertiary. In distribution the deposits of the three periods, with certain exceptions, show a concentration about two large positive areas, the Colorado plateau and the Columbia plateau, which suggests a causal relation. The most general age divisions of the rocks of the Cordilleran region of the United States are (1) pre-Cambrian, and (2) Cambrian and later rocks. The pre-Cambrian rocks are exposed mainly through the Rocky Mountain belt from the Canadian boundary southward to Arizona and westward through Arizona to southern California. They have commonly

Jan 1, 1933

By F. G. Smith

A FEW years ago, the writer encountered a, problem that, at first, seemed to be due to peculiar conditions affecting grain growth. Large cups made from heavy metal failed in the first drawing operation in the process of making seamless tubes. The metal, as cast, appeared to be sound and strong; it rolled successfully and withstood the first cupping operation, but on the first draw it failed, with a crystalline fracture. The failure appeared in the slightly worked part of the bottom of the cup, and microscopic examination revealed exceptionally large grains. Knowing the general conditions governing recrystallization of brass, which were later published by Matthewson and Phillips, an investigation was outlined with the idea of including various conditions under which new grains might form, and which would include the effect that a previous anneal might have upon the anneal following. These conditions were produced by annealing specimens of brass at five different temperatures, indenting them with a 10-inn. ball under four different pressures, and then reannealing at each of the five temperatures five specimens each of which had been annealed at one of the five temperatures.

Jan 8, 1919

By Richard H. Bube

Photoelectronic radiation detectors may be conveniently classified as homogeneous intrinsic, homogeneom extrinsic, or junction type. Highly photosensitive homogeneous intrinsic photodetectors may be prepared from a number of different II-VI, III-V, or IV materials. Such materials require the presence of specific imperfections that can act as sensitizing centers to provide long majority carrier lifetime. Homogeneous extrinsic photodetectors are of interest primarity for infrared detection, and consist principully of germaniuim and silicon with suitable inpurities. A vaviety of junction photodetectors exist, with silicon us the most common material for them all. The following extrema in performance are found: 1) highest photoconductivity gain in homogeneous intrinsic photodetectors; 2) smallest response time (highest frequency response) in p-i-n junctions; 3) largest gain-bandwidth product in avalanche diodes. ALTHOUGH the total number of materials exhibiting photoconductivity effects is very large, only a relatively few of these have appropriate properties for a practical photoelectronic radiation detector. In fact if one surveys the commercial detectors currently available, one finds that the field is dominated by some ten or fewer materials. These are summarized in Table 1 in terms of the other important variable in detector fabrication, the structure of the material, i.e., whether the material is used as a single crystal or in polycrystalline form, and whether the material is used as a homogeneous detector or whether the detector depends upon the existence of a junction or barrier in the material. The principal wavelength range for each type of material is also shown, together with an indication of the utilization of intrinsic or extrinsic excitation. For the purposes of the present comparison of various detectors, it will be convenient to discuss two main topics: homogeneous photodetectors and junction photodetectors. The performance of a photoelectronic radiation detector is measured in terms of two parameters: the photoconductivity gain, and the response time of the detector. A convenient figure-of-merit is given by the ratio of gain to response time, often called the gain-bandwidth product. The photoconductivity gain is a device parameter since it varies in many cases with the applied voltage and the detector geometry, and should be distinguished from the actual photosensitivity of the material involved. This photosensitivity can be conveniently given as the product of free carrier lifetime and mobility in the material. The photoconductivity gain is defined as the number of charge carriers which pass between the electrodes per second for each photon absorbed per second, where G is the photoconductivity gain, is the pho-tocurrent in amperes, e is the electronic charge in coulombs, and F is the total number of electron-hole pairs created in the photo conductor per second by the absorption of light. The gain may also be expressed as the ratio of the lifetime of a free carrier to the transit time for that carrier, i.e., the time required for the carrier to move between the electrodes. For a material in which one-carrier conductivity dominates, where T is the lifetime of a free carrier, ttr is the transit time for this carrier, p is the carrier mobil-ity, V is the applied voltage, and L is the electrode spacing. From Eq. [2] it follows that the photoconductivity gain is proportional to the photosensitivity of the material (tP), the proportionality constant being The photosensitivity of a material, and hence the photoconductivity gain of a device utilizing the material, depends on the lifetime of the free carriers as a critical parameter. In a homogeneous material this lifetime is determined by the nature of imperfections in the material, and in an inhomogeneous material the lifetime is determined by the specific junction structure. The speed of response, the other basic photodetec-tor parameter, is determined by factors quite similar to those important for photoconductivity gain. Imperfections are of primary importance in homogeneous materials, and the structure of the junction is a determining factor in junction devices. For infrared detectors it has become common to define another quantity designed to indicate directly how effective the detector is in distinguishing between a small photoconductivity signal and random noise due to the detector and its environment. The detectivity D* is given by

Jan 1, 1968

By Donald H. McLaughlin

ZEST in the search for new supplies of metallic ores and petroleum is difficult to maintain with stocks of raw materials accumulating and with over- production rightly or wrongly blamed for most of our industrial troubles. Enthusiasm over new methods of prospecting has consequently diminished and exploration programs in many fields have been drastically cur- tailed. Very naturally the effects have been felt with particular keeness in highly specialized phases of the work, such as geophysical prospecting, for the feverish scramble for new areas in which to drill beneath magnetic or electrical anomalies has abated, and there is even a lull in the firing in the battle over salt domes on the Gulf Coast. It is unquestionably an unhappy time for many of the organizations dependent on this work, but in certain respects the situation may be beneficial in correcting unsound practices that .have grown up through the necessity for haste and for quick decisions. With the restriction of the field to the more competent workers by the harsh rule of survival of the fittest, a general improvement, not only in technique but in business methods, can be expected which may go far in restoring public confidence. Geophysical prospecting in the short period that it has been utilized in North America, has suffered severely both from over-popularity and from excessive abuse. The former evil now

Jan 1, 1931

By S. Saito, P. A. Beck

The crystal structure of MoNi3 was determined by means of X-ray diffraction. This structure is isotype with that of ovgered TiCu3. The lattice parameters are: a. = 5.064A, bo = 4.224A, co = 4.448A, and zf 0.157. If the orthorhombic distortion (slight relative to the corresponding orthohexagonal unit cell) is disregarded, the structure may be described in terms of a close-packed ordered atomic layer, stacked in the sequence: abab. The structztres of ordered TiCu3 and TiAl3 are homotectic. The three types of ordered hexagonal phases, iso-structural with TiNi3, MgCd3, and VCo3, are known to occur in AB3 alloys of transition elements of the first, second, ad third long periods. It was noted1 that phases with the TiNi3 structure occur selectively in alloys of Ti-group elements with Ni-group elements. In AB3 alloys of Ti-group and V-group elements with Co-group elements the AuCu3-type structure predominates.' The vCO3 structure, which was determined very recently,' has hexagonal symmetry, but the actual atomic arrangement here, too, is rather closely related to the ordered cubic structure of AuCu3-type. However, an ordered hexagonal close-packed structure of the MgCd3-type occurs in MOCO33 and WCO3.4 Consequently, the question arises as to whether or not the crystal structure of MoNi3 is also of the MgCd3-type. Grube and winkler5 found that MoNi3 has a hexagonal close-packed structure with a = 2.54A and c/a = 1.65. They pointed out that some additional weak diffraction lines could be observed in the powder pattern, which may have been due to an ordered atomic arrangement in this phase. However, no detailed information was obtained by them and the structure was apparently not further investigated by others. The present work was, therefore, undertaken in an attempt to determine in detail the structure of MoNi3, and to investigate the possibility of ordering. EXPERIMENTAL METHODS Alloys used in the present work were arc-melted in a water-cooled copper crucible under helium atmosphere. Electrolytic nickel and molybdenum, both 99.9 pct pure, were used. Chemical analyses were not made, but the melting loss was not higher than 2 pct for any alloy. Ingots were first homogenized at 1200°C for 48hr, quenched, heavily cold worked, and then annealed at 820" or 860°C for 1 week, followed by quenching in cold water. Powder specimens for X-ray work were prepared by crushing the heat-treated solid specimens. In order to remove strains, the powders were reannealed in evacuated scaled fused silica capsules for 6 hr at the same temperature at which the corresponding solid specimens were annealed. X-ray photographs were taken with an asymmetric focussing camera, using unfiltered CrK or CuK radiation. EXPERIMENTAL RESULTS The X-ray diffraction patterns of alloys containing 20.8, 25, and 26.4 at. pct Mo, homogenized at 1200°C, showed the face-centered-cubic structure of the Ni-base a-solid solution. It was revealed, however, by micrographic examination that the 26.4 at. pct Mo alloy contained in addition very small amounts of a second phase, in accordance with the phase diagram.6 On the other hand, the 20.8 at. pct Mo alloy after annealing at 820°C gave the X-ray diffraction pattern of the ordered face-centered-tetragonal MONi4.7 In this pattern several additional weak diffraction lines were also observed, corresponding to the strongest diffraction lines of MoNi3. The alloys containing 25 and 26.4 at. pct Mo after annealing at 820" or 860°C gave X-ray diffraction patterns, as shown in Tables I and 11, corresponding to MoNi3. Each one of the reflections which could be tentatively indexed on the hexagonal close-packed cell of Grube and Winkler,5 with the exception of the basal plane reflections, was split into a doublet, as seen in Table I. Since microscopically the alloy consisted of a single phase, it seemed probable that the lattice of MoNi3 is actually slightly deformed, as compared with the tentative hexagonal unit cell. In addition to these diffraction lines, several weak lines were also present, as shown in Table 11, which could not be indexed at all on the hexagonal close-packed cell considered. Satisfactory indexing of all diffraction lines observed was found to be possible by using an orthorhombic unit cell with ao = 5.064A, ft = 4.224A, and c = 4.448A. These values, whose accuracy is estimated to approximately ± 0.008A, correspond to 95.14A3 for the volume of the unit cell, and to an X-ray density of 9.50 g per cm3. If no attention were paid to the weak reflections listed in Table II, a reduced -unit cell of half the volume (a = 2.532A, b = 4.448A, and c = 4.224A), closely related to the orthohexagonal cell, might be used. The dimensions of the orthohexagonal cell of the same volume as the reduced cell are: a = 2.562A, b = 4.437 A, and c = 4.183A. It may be seen that in the reduced cell the a axis is slightly shorter, while the b and c axes are slightly longer than those corresponding to the orthohexagonal cell of the same volume. This slight orthorhombic distortion is re-

Jan 1, 1960

By David R. Mitchell

Many of the difficult operating problems of the preparation of coal for market, of sampling coal shipments and in the utilization of coal are caused by segregation in the coal mass. Segregation may be of two kinds: i.e., "size segregation," in which particles of the same size in a mass of coal containing a range of sizes collect together and "density segregation," in which particles of the same density or specific gravity in a mass of particles of varying density gather together. Mechanics of Segregation Size segregation cannot take place with closely sized coal. As the size range increases, the tendency for size segregation increases. Similarly, cleaned coal with particles of approximately the same specific gravity have very little tendency for density segregation. The wider the density range of particles and the more particles of different density, the greater the chances are for density segregation. The following discussion deals primarily with coal of a wide size range as screenings and of wide density differences as uncleaned or run-of-mine screenings. If a mass of coal containing particles of a wide size range is subject to the stream action of a moving current of water, the small particles are transported farther than the coarser. Particles of different density in a stream of moving water are subject to the laws of classification, the heavier settling out first. The familiar sluice box of the gold miner and the action of rivers and other streams in classifying material according to

Jan 1, 1938

By David R. Mitchell

Many of the difficult operating problems of the preparation of coal for market, of sampling coal shipments and in the utilization of coal are caused by segregation in the coal mass. Segregation may be of two kinds: i.e., "size segregation," in which particles of the same size in a mass of coal containing a range of sizes collect together and "density segregation," in which particles of the same density or specific gravity in a mass of particles of varying density gather together. Mechanics of Segregation Size segregation cannot take place with closely sized coal. As the size range increases, the tendency for size segregation increases. Similarly, cleaned coal with particles of approximately the same specific gravity have very little tendency for density segregation. The wider the density range of particles and the more particles of different density, the greater the chances are for density segregation. The following discussion deals primarily with coal of a wide size range as screenings and of wide density differences as uncleaned or run-of-mine screenings. If a mass of coal containing particles of a wide size range is subject to the stream action of a moving current of water, the small particles are transported farther than the coarser. Particles of different density in a stream of moving water are subject to the laws of classification, the heavier settling out first. The familiar sluice box of the gold miner and the action of rivers and other streams in classifying material according to

Jan 1, 1938

By G. L. Fisher, R. Maddin

The rate of self-diffusion in silver single crystals during torsional strain was measured over a wide range of tenperatures and strain rates. The torsional strain was applied in a cyclic manner by reversing the divection of twist aftev a certain fraction of the total strain was reached. Surface roughening was substantially reduced in cyclically strained specimens compared with those strained entirely in one direction. Diffusion coefficients were determined using a special sectioning technique whereby slices could be removed parallel to the surface of a strained torsion specimen. The accuracy of the technique was first determined using roughened specinzens statically diffused to various penetration depths. Simultaneous strain-diffusion experiments were then performed over the temperature range 550' to 800 using strain rates of lo-' to 2.2 x 10' sec-'. The increase in silver self-diffusivity during torsional plastic strain was small. In only one case was the enhancement greater than twice the static value of the diffusion coefficzent. The enhancements increased slightly with decreasing tenzperature and increased with increasing strain rate. A dislocation pipe mechanism of enhancement was found to explain the present results satisfactorily. The magnitude of the enhancements and the tenzperatures at which they were observed suggests that a steady-state dislocation density of 10' to 109 dislocations cm-2 existed during the high-tempevature deformation. The diffusion coefficient in an fcc metal can be increased by 1) an excess concentration of point defects and 2) the rapid movement of diffusing atoms along grain boundaries and dislocations. Plastic deformation may be responsible for enhancements by both of these mechanisms. The results of simultaneous strain-diffusion experiments have caused a controversy over the magnitude of the effect of strain upon diffusion. Experiments reporting large enhancements have been criticized for the manner in which the diffusion coefficient was measured. Several of these experiments have been contradicted by other results obtained in a similar manner. No enhancement was reported by two investigators''' who performed their experiments at high temperatures where strain is expected to have little effect upon diffusion. A recent theoretical analysis3 indicates that strain enhancement by a vacancy mechanism will be small and exist only at low temperatures and rapid strain rates. It is doubtful whether any experiment has yet proven that strain enhancements can occur by an excess vacancy mechanism. In the present research, experiments were performed at extremes of temperature and strain rate in an attempt to measure enhancement of diffusion by strain. Self-diffusion of silver during torsional deformation was chosen since two separate investigations4j5 indicate that at least a small enhancement exists under these conditions. An accurate method of determining the diffusion coefficient, mechanical sectioning, was employed after a technique was devised to apply it to the roughened surface of a strained torsion specimen. First, the accuracy of the technique was determined for different penetrations (2fi). Then diffusion experiments were performed at temperatures between 550" and 800°C at strain rates of 10"" to 10"" per sec. I) EXPERIMENTAL PROCEDURE Preparation of Specimens. The experimental procedure detailing the growth of crystals, their treatment, and the annealing techniques during straining are contained in earlier publications.496 The dimensions and orientations of the torsion specimens are shown in Figs. 1 and 2. licatiin of Torsional Strain. The torsion procedure was changed from that used previously. The specimens were strained in cycles to reduce the gross distortion and surface roughening inherent in twisting to high strains in one direction. For all strains above 0.30, the total surface strain was obtained as follows: the specimen was twisted to 0.10 strain in a clockwise direction; the direction was reversed; the backlash in the torsion apparatus was taken up; and the specimen was twisted in a counterclockwise direction through the initial starting point to 0.20 surface shear strain in the opposite direction. The strain reversal took no more than 1 min to accomplish. The total accumulated surface shear strain was arbitrarily taken as the sum of the 0.10 strain in the clockwise direction plus 0.20 in the counterclockwise direction. Although cyclic torsional strain was beneficial, surface roughening and specimen distortion were not entirely eliminated. The variation in the diameter at various points on the specimen was often much greater than the depth of the diffusion zone. Since serious errors might result if specimens were sectioned in the usual manner, a technique of lathe sectioning was devised to allow sections to be taken parallel to planes of equal concentration.

Jan 1, 1967

By Frederick Laist

This paper is a review of Montana reverberatory smelting practice covering a period of approximately fifty years, during which time the small furnaces that had been in use elsewhere for a century or more, without much change in size or method of operation, were revolutionized and were developed into the huge, continuously operating furnaces of today. A study of Montana practice is particularly instructive, since reverberatory furnace smelting for the production of copper matte received more attention there than in other smelting centers and many of the improvements that finally resulted in establishing the preeminence of this type of furnace over the blast furnace originated in Butte and Anaconda. The material in this paper was gathered from original sources, wherever possible, and all of the illustrations were made from original drawings, some of which have been simplified and worked over so as to be better adapted for reproduction. The aim has been to trace the modifications in design and operation which took place during the period in question—the reasons for the changes and the results achieved through them. For developments during the first twenty years, the technical literature of the period was freely drawn upon, but I am particularly indebted to W. M. Kelly, general foreman at the Anaconda Works, whose recollections and personal experience extend back to the early days. I wish to acknowledge the use made of publications of E. P. Mathewson, William Wraith and L. V. Bender, as well as information obtained here and there from friends and associates. The resume of Great Falls practice was compiled from correspondence, notes and drawings found in the files of the old Boston & Montana Co. and the tabulations showing the performance of furnaces at Butte and Anaconda are adapted from plant records and correspondence in the files of the Anaconda Copper Mining Company. The paper deals with some interesting comparisons that were made between furnaces operated under various conditions in connection with the Carson Case, and results obtained when using natural gas as fuel. This part of the paper may be considered original to the extent that these results have not previously been published.

Jan 1, 1934

By H. O. Hoffman, C. D. Demond

There are two methods of determining the fusibility or refractoriness of fire-clays, the theoretical and the experimental. In the former, conclusions are drawn from the chemical composition; in the latter, from the changes which the clay undergoes when subjeoted to intense heat. It is well to use both methods, beginning with the actual heat-test and explaining the results obtained from this by the help of the chemical analysis. In discussing the subject, however, it is better to reverse this order. I. The Theoretical Method.* Leaving out the hygroscopic and combined waters and any organic matter, as not directly affecting the fire-resisting property, the refractory constituents of fire-clay are alumina and silica, and the fluxing constituents magnesia, lime, soda, potash and ferric oxide. According to Bischof,† alumina is the least fusible component, and silica follows close upon it. If, however, a mixture of the two be heated, it will be found that its melting-point is much lower than that of alumina, as a silicate will then have been formed. The way in which silica affects the refractoriness of alumina has been strikingly presented by Seger 1 in a diagram reproduced in Fig. 1. The abscissæ represent the melting-points of Seger cones Nos. 26 to 36 (see p. 55); the ordinates, the relative amounts of alumina and

Jan 1, 1895

The high-grade orebody at Miami was mined successively by top-slicing, shrinkage, stoping and under caving. The method described in this paper was developed to enable the low-grade orebody (36,000,000 tons assaying 1.06 per cent copper) to be mined at a low cost without further dilution of the grade. The method is clearly described and illustrated by drawings and photographs, and the original paper should be consulted as it is impracticable to abstract it, beyond noting that the mining cost is just under 40 cents per ton and the average grade of ore now being produced yields less copper than the mill tailing of 1915, the tons mined per day having increased from 4000 to 18,000 in the same period. Vertical and Incline Shaft Sinking at North Star Mine By Arthur B. Foote, Grass Valley, Calif. (Tech. Pub. No. 324: Class A. Metal Mining, No. 36) THE main shaft of the North Star mine is an inclined one following the main vein at an average dip of 26 deg., a vertical shaft intersects it at the 4000-ft. (incline) level, the incline continuing to the 6300-ft. level. At this point the vein was found to give out and a new vein, called the No. 1, was found to dip in exactly the opposite direction.

Jan 1, 1930

By Finlay, J. S.

THE North Lily Mine started its career in an unusual way it was discovered by a geologist. The remarkable circumstance of driving a 2400-ft. drift into an unexplored country and "hitting her on the nose," indicates that geologists are sometimes numbered among those whom the Lord loves. Diamond- drilling from surface had previously shown the presence and position of the Ophir beds, and surface showings of pebble-dykes, faults, and bleached rhyolite indicated conditions similar to those at the Tintic Standard "Pot-hole." The discovery drift from the Tintic Stand- ard 700-level reached the North Lily orebody in January, 1926, and development and stoping were continued by Tintic Standard men and equipment until the North Lily shaft was sunk and put into service in May, 1928. The discovery drift was run on a cooperative basis by the Tintic Standard and North Lily mining com- panies. Finding the North Lily mine cost the North Lily company $26,000. The Tintic Standard Mining Co. furnished men and equipment to drive this discovery drift at a fraction of what it would have cost to find the orebody from surface. This was the beginning of the friendly cooperation that still exists. Through Tintic Standard ground the Tintic Standard paid two- thirds of the cost and the North Lily one-third; the cost of the drift through Eureka Lily, into North Lily ground, was paid by North Lily. Later, another drift from the Tintic Standard 900-level was run on the same plan, excepting that Eureka Lily paid its share of the cost; that is, the Eureka Lily paid one-third of the expense in Tintic Standard ground, and the Eureka Lily two-thirds and North Lily one-third in Eureka Lily ground. This 900-drift was driven by North Lily from the Eureka Lily line to near the North Lily west side-line. From this point the Chief Consolidated continued the drift well into Tintic Bullion ground.

Jan 1, 1929

By O. C. Wheeler

In order that the series of reports on oil and gas in Colombia may be complete, the report for the year 1941, which was not available for Volume 160 of the TRANSACTIONS, is given here. The report for 1945 begins on page 4o6.

Jan 1, 1946

By J. P. Smith

DURING the winter of 1946 to 1947 potash operations in Germany, France and Spain were visited by the author. The U. S. Department of Commerce, through its Field Intelligence Agency Technical, sponsored the inspection of German properties by representatives of the American Potash Industry. Vast deposits of potash salts occur in the above-mentioned countries, and the production and marketing of these salts are important in their respective economies. Germany An area of some ten thousand square miles of north central Germany is underlain by lenses of potash salts interbedded with greater thicknesses of sodium chloride or common salt. These salt measures are relict deposits from the evaporation of an arm of the Zechstein (Permian) Sea which formerly covered northern Europe. During the peak year of 1940, Germany produced salts containing 1,860,000 tons of K,O and, next to coal, potash is its most important mineral raw material. The German deposits are found in the synclinal areas flanking the Flechtingen, Hartz Mountain and Thuringian uplifts, and, to the north they lie beneath the plains of Hannover. The regional dip of the salt measures is to the north, hence, lenses of potash found at depths of 500 to 1000 m* in the Two general depositional provinces of potash concentrations are recognized: (1) the main basin, and (2) the subsidiary basin. The main basin embraces the producing districts of Stassfurt, Sud Hartz, Halle, and Hannover-Braunschweig. From J. P. SMITH, Member AIME, is Clzief Geologist, U. S. Potash Co., Carlsbad, New Mexico. New York Meeting, February 1948. TP 2621 H. Discussion of this paper (2 copies) may be sent to Transactions AIME before Feb. 28, 1950. Manuscript received May 26, 1948. 40 to 45 pct of the German production comes from this basin. The Werra-Fulda district, producer of 50 pct or more of the German potash, lies in the subsidiary basin. Salt Stratigraphy: Five commercial potash zones or beds are recognized. The three beds present in the main basin are: The Stassfurt bed that occurs near the top of the older salt, and the Ronnenberg and Riedel beds in the younger salt occurring 200 to 300 m, respectively, above the Stassfurt bed. The Stassfurt bed is found over the entire main basin, while the Ronnenberg and Riedel are restricted to the Hannover area. Two potash beds occur in the Werra basin. These are the Thuringian, or lower bed and the Hessen or upper potash bed that occurs 60 m above. These beds lie 210 and 150 m, respectively, below the position of the Stassfurt bed, and are restricted to the Werra basin. The upper bed is 2.5 to 11.5 m in thickness, and the principal ores are hartsalz with varying thicknesses of carnallite. The lower bed averages 3 m in thickness, and contains hartsalz. The upper bed is presently being mined, and the

Jan 1, 1951

By J. P. Smith

DURING the winter of 1946 to 1947 potash operations in Germany, France and Spain were visited by the author. The U. S. Department of Commerce, through its Field Intelligence Agency Technical, sponsored the inspection of German properties by representatives of the American Potash Industry. Vast deposits of potash salts occur in the above-mentioned countries, and the production and marketing of these salts are important in their respective economies. Germany An area of some ten thousand square miles of north central Germany is underlain by lenses of potash salts interbedded with greater thicknesses of sodium chloride or common salt. These salt measures are relict deposits from the evaporation of an arm of the Zechstein (Permian) Sea which formerly covered northern Europe. During the peak year of 1940, Germany produced salts containing 1,860,000 tons of K,O and, next to coal, potash is its most important mineral raw material. The German deposits are found in the synclinal areas flanking the Flechtingen, Hartz Mountain and Thuringian uplifts, and, to the north they lie beneath the plains of Hannover. The regional dip of the salt measures is to the north, hence, lenses of potash found at depths of 500 to 1000 m* in the Two general depositional provinces of potash concentrations are recognized: (1) the main basin, and (2) the subsidiary basin. The main basin embraces the producing districts of Stassfurt, Sud Hartz, Halle, and Hannover-Braunschweig. From J. P. SMITH, Member AIME, is Clzief Geologist, U. S. Potash Co., Carlsbad, New Mexico. New York Meeting, February 1948. TP 2621 H. Discussion of this paper (2 copies) may be sent to Transactions AIME before Feb. 28, 1950. Manuscript received May 26, 1948. 40 to 45 pct of the German production comes from this basin. The Werra-Fulda district, producer of 50 pct or more of the German potash, lies in the subsidiary basin. Salt Stratigraphy: Five commercial potash zones or beds are recognized. The three beds present in the main basin are: The Stassfurt bed that occurs near the top of the older salt, and the Ronnenberg and Riedel beds in the younger salt occurring 200 to 300 m, respectively, above the Stassfurt bed. The Stassfurt bed is found over the entire main basin, while the Ronnenberg and Riedel are restricted to the Hannover area. Two potash beds occur in the Werra basin. These are the Thuringian, or lower bed and the Hessen or upper potash bed that occurs 60 m above. These beds lie 210 and 150 m, respectively, below the position of the Stassfurt bed, and are restricted to the Werra basin. The upper bed is 2.5 to 11.5 m in thickness, and the principal ores are hartsalz with varying thicknesses of carnallite. The lower bed averages 3 m in thickness, and contains hartsalz. The upper bed is presently being mined, and the

Jan 1, 1951

By Burt C. Mariacher

To note that environmental considerations had a major im¬pact on the minerals processing industry in 1971 would be something less than a profound observation. The degree of its importance was demonstrated by MBD when it established the Environmental Committee as a new unit committee within the Division to achieve greater participation in exchange of information relating to the technologies and problems involved. It is appropriate and necessary to devote special attention to this timely aspect of minerals processing, as its influence penetrates the research, engineering and operations of almost all unit technologies that comprise minerals processing. The pollution abatement aspect of this industry has been such a dominant factor in recent years there is reason to wonder whether progress in unrelated technologies has been curtailed. Perhaps so, to some degree, but unit committee reviews presented in this article suggest rather that it would appear to have served as a catalyst for accelerated progress in development of new methods and improvement in more conventional ones. Present concepts regarding primary metal or mineral recovery and by-product potential may change considerably as a result of improved technology in waste product treatment.

Jan 2, 1972

By Frances H. Clark

IN a concern with the varied interests of the Western Union Telegraph Co., where practically all types of metals, both ferrous and nonferrous, are utilized, many types of failures of materials occur. These have to do not only with outside plant construction, such as corrosion and fatigue of line wire and cable, but also with inside plant equipment operating at such high speeds that rapid deterioration of metal. parts due to fatigue and wear results. Both corrosion and fatigue affect the life of copper wire so its normal life in any particular locality is largely dependent on the atmospheric conditions. Tensions vary widely owing to changes in temperature and ice and wind loadings and the wire is Subject to a great range of vibration caused by wind gusts aril vibration front trains or other heavy vehicles transmitted through the earth. High frequency low-amplitude vibrations are sometimes audible as singing in the wire. The other extreme is the vertical slashing or dancing of the wire observed during severe storms where amplitudes of 9, ft. or more at low frequencies have been observed.

Jan 1, 1942