Search Documents

By G. B. Craig, B. Ramaswami

The temperature and strain rate dependence of the flow stress ratio and the stvain rate dependence qi the flow stress of annealed polycrystalline a zirconiur were determined over the temperature range 30 0" to 1000°K. Some evidence was found for strain aging and discontinuous flow in the temperature ranges 520" to 650°Kand650" to 760°K, respectively. The Cottvell-Stokes relationship was obtained when deformation occurred by twinning as well as slip. The flow stress ratio showed a strong dependence on temperature and strain rate above 800°K. The expevirnental evidence indicated that the rate-controllitzg mechanism for the deformation of a zirconium above 800°K was dislocation climb, and that the deformation was not thermally activated in the range 520" to 800°K. The stacking-fault energy of a zirconium was estimated to be about 250 ergs per sq cm. A knowledge of the temperature and strain rate dependence of the applied stress necessary to deform a crystalline solid is essential for understanding the thermally activated processes occurring during deformation.' Several experimental techniques have been developed for studying these processes.273 One of the techniques is the deter mi nation of the strain rate dependence of the flow stress at constant temperature. In close-packed crystals, it has often been observed that the change in stress due to a change in the strain rate varies linearly with the flow stress, (~1,' This relationship, known as the Cottre ll-Stokes law, is obeyed when deformation occurs by glide alone. However, when deformation occurs by twinning as well as glide, there is disagreement among different investigators on whether the Cottrell-Stokes law is observed. Whereas Thornton et ~1.~find departures from Cottrell-Stokes law when twinning occurs in copper, ~avis~ and sasinski? find that Cottrell-Stokes law is obeyed when deformation occurs by twinning as well as slip in cadmium and magnesium, respectively. One of the main objectives of this study is to determine whether the Cottrell-Stokes law is obeyed when deformation occurs by twinning as well as slip. The second technique that has been used extensively to study the thermally activated deformation of crystals is the determination of the ratio of the flow stresses, at identical dislocation structures and con-

Jan 1, 1968

The American mining industry is vigorous today because it is young. At a time when the ore deposits of central Europe, for example, were being exploited actively, those of the United States were lying practically untouched. The founding fathers of our republic were not interested in mineral wealth because they were ignorant in such matters; their preoccupations were with defence against the Indians, the clearing of the forest, and the starting of agriculture in their new domains. They had no idea of establishing a mining industry. The Indians whom the American colonists dispossessed had no mines; they used only the metal that was to be found lying on the surface of the ground. Their arrows and spears were tipped with flint, which likewise called for little digging, if any. The native copper that glacial action had torn from the lodes of the Lake Superior region and had carried into the valleys of the Ohio and Mississippi was employed in the making of earrings, bracelets, knives, and scrapers. The same useful metal was found in many other places, in Virginia and Carolina, in Vermont and New Jersey, for example, but the Indians did not know how to melt it, much less how to smelt the ore, therefore they shaped it into tools and implements by hammering. Fortunately for them the hammering of the metal caused it to harden and therefore to become serviceable for implemental use. It is doubtful if they obtained the copper by actual mining, that is, by digging or excavating; it is true we find traces of such operations in the Keweenaw .peninsula of Michigan, but we have no

Jan 1, 1932

By Philip B. Bucky

[ ] FOREWORD THIS symposium brings together points of view, experiences and ideas on rock bursts from a goodly portion of the globe. Some conceptions, particularly those regarding the necessity of depth, have been fairly well shattered, as we find that they are present in the water tunnels of New York, on the surface at marble quarries in Vermont, and in the coal mines of the United States, as well as in the deep mines of the South African and Kolar gold fields, and in the nickel, copper and gold mines of Canada. Their occurrence under such a variety of conditions is, therefore, a challenge,

Jan 1, 1942

By H. G. Schneider

The Smackover oil and gas field lies in Ouachita and Union Counties, Ark., in the south-central part of the state, in T.15 and 16S., R.15, 16, and 17W. It is 10 miles north of El Dorado, the principal business and railroad center in the south-central part of the state, and extends from the town of Smackover in all directions. Productive territory having an aggregate area of nearly 55 sq. mi. has been developed. It extends 6 miles from north to south and 12 miles from east to west. The field may be divided into two parts: the east district, which includes the area east of the town of Smackover, and the west district, which includes the area west of the town of Smackover. In relation to the neighboring productive fields of Arkansas, the Smackover field is 9 miles north of the El Dorado oil and gas field, 8 miles slightly west of north of the East El Dorado oil and gas field, and 16 miles east of the Stephens oil field. Smackover was discovered in May, 1922, when the Oil Operators Tnist drilled well No. 1 on the J. T. Murphy farm, in the southeast quarter of sec. 8, T.16S., R.15W. This well is located almost on the top of the Norphlet dome and was drilled to the Nacatoch sand. It had an initial open flow volume of 30,000,000 cu. ft. of dry gas per day, and a rock pressure of 950 lb. per sq. in. In July, 1922, the V. K. F. Co. completed the first oil well in sec. 29, T.l5S., R.l5W., on the north side of the Norphlet dome, and 3 miles north of the first gas well. This well started the active development of the north and northwest sides of the dome.] The field was extended westwards, when oil was discovered in the Nacatoch sand, during October, 1922, in sec. 4, T.l6S., R.l6W., 51/2 miles west of the original gas well. This opened up the so-called "light oil district," which is located on a structural terrace, for which the name

Jan 1, 1924

By George A. Morrison

THE Columbia Chemical Division of the Pittsburgh Plate Glass Co. is at Barberton, Ohio, 35 miles south of Cleveland. For many years large tonnages of limestone have been brought to the Barberton plant from distant points. The stone is here burnt in vertical kilns, the resultant product then hydrated and the hydrated lime used in chemical processing. To eliminate the expense of these shipments, the company decided to investigate a limestone bed known to exist on company property at Barberton, where the stone is used. The bed lay at a depth of more than 2000 ft. and was known locally as the "Deep Lime." Chemical analyses of sludge from churn-drill holes made some years ago proved that the limestone was of sufficient purity to warrant diamond-drill exploration. Four diamond-drill holes were put down at well-spaced intervals, to represent fairly an area of four miles by one mile. Cores logged as to chemical and physical conditions were found to compare closely, and to corroborate the earlier evidence that the limestone was of superior quality for chemical use. A plant of 300 tons per hour was subsequently decided upon. SITE The yard at the chemical plant was already so congested that location of the projected mine within its area could not be considered. Eventually a site was selected 2 miles northwest of the plant, near the main line of the Erie Railroad. Here 412 acres were owned outright by the company and stone rights were obtained on 250 additional acres. This location required a transportation line of nearly 2 miles (8800 ft.), crossing two major highways, and to avoid interruption of deliveries to the plant, overpasses were planned. GEOLOGY The limestone in the immediate vicinity lies about 2200 ft. below the surface. Geologists* identify this stone as Delaware of Devonian age. It is overlain by 18 ft. of unconsolidated (sand and gravel), 100 ft. of water-bearing sandstone, and finally 2080 ft. of shale into which sandstone in thin layers is interbedded. The contact of shale and limestone is abrupt, flat-lying and very pronounced. Berea sandstone, often found at 520 ft., is absent, but Euclid sandstone was encountered, together with a seepage of oil and a small amount of methane gas. The limestone bed itself is 345 ft. thick, and overlies 200 ft. of gypsum. The lower part becomes dolomitic as it approaches the gypsum. A detailed study of the drill cores indicates that the upper 50 ft, are highest in lime and reasonably low in silica. The physical make-up shows several separating cherty layers. These occur at definite horizons and cause distinct partings, which become horizontal planes of

Jan 1, 1943

By R. V. Higgins

This paper presents a computer method to obtain the shape factors and equal cell volumes of the channels for any well spacing pattern from a potentiometric model. By using this program the authors have processed the data for the seven-spot, direct line-drive and the staggered line-drive patterns. The data for the five-spot pattern had been previously processed by a noncomputer method and are included for completeness. The shape factors and volumes for the channels are presented in tables for those who want to use them to process data using their own permeability relationships and viscosities of their reservoir oils. The authors have used the data and sets of representative permeability curves to process sample calculationr of waterflood performances. The comparison of the calculated results shows that the influence of well spacing is small. The permeabilities of the reservoir rock to oil and water had a greater influence on oil recovery for a given pore-volume throughput of water than the well spacing pattern. The more water-wet the reservoir rock, the better the possibility of permeabilities which are conducive to good recovery. The viscosity of the reservoir oil also influences the recovery more than the well spacing pattern. The reduction in the percentage recovery of oil with increase in viscosity of the reservoir oils is small when oil viscosities are in the range of 0.1 to 3. Above this range the reductions in recoveries are extensive. Sample comparisons of the time required for different patterns to recover the oil are presented. Results of an example calculation are given to show the effect of the permeability profile on recovery. INTRODUCTION The effect of well spacing pattern on the recovery of oil when flooding with either gas or water has been studied by many investigators. Muskat et al.1 presented an analysis using conductivity, sweep efficiency and unit mobility to the time of breakthrough. Dyes et al.2 used experimental techniques (X-ray shadowgraphs) and different mobility ratios. They presented quantitatively the relationship between mobility and sweep efficiency at and after breakthrough. Hauber3 presented a method to predict waterflood performance for arbitrary well spacing patterns and mobility ratios. Craig et al.,4 using techniques similar to Dyes et al. to determine sweep efficiency for a five-spot pattern, added the use of relative permeability curves at breakthrough and thereafter. Douglas et al.5 sed rela- tive permeabilities and continuously changing saturations throughout the entire five-spot flood pattern. In obtaining their solutions they used finite-difierence equations. Hig-gins and Leighton6,7 also used relative permeabilities and continuously changing saturations throughout the pattern before and after breakthrough. They employed techniques that process a flood-pattern calculation on the computer in about one minute. The methods of Douglas et al. and Higgins and Leighton both checked closely the laboratory results for a wide range of mobility ratios. This paper presents some sample performances calculated by the Higgins and Leighton method that show the effect on recovery of different permeabilities and viscosities using the seven-spot, the line-drive and the staggered line-drive, as well as the fivespot flood pattern. No previous paper has presented these data using different permeability curves and continuously changing saturations throughout the flood patterns. The paper also presents (1) the results and analyses of the flood-pattern prediction, (2) the computer techniques for determining the shape factors and volumes from the potentiometric models for the foregoing flood patterns, and (3) the shape factors and volumes of the channels of the flood pattern in the event reservoir engineers may like to process waterflood calculations using their own permeability curves and reservoir oils. DESCRIPTION OF METHOD VOLUMES AND SHAPE FACTORS The use of channels taken from a potentiometric model (see Fig. 1) to aid in calculating the performances of water floods of nonlinear patterns has been thoroughly explained in the literature.0,7 Therefore, very little theory, discussion, or proof regarding this phase will be repeated in this paper. The computer method presented in this paper to calculate the volumes and the shape factors of the channels of potentiometric models employs the trapezoidal rule for the volumes and the Pythagorean theorem (the hypotenuse equals the square root of the sum of the squares of the two sides of a right triangle) for the shape factors. In calculating the volume of a channel, the area of each cell in the channel is determined and then multiplied by the thickness to obtain the volume. In determining the areas of the cells, trapezoids are constructed whose vertical sides are spaced Ax apart, as shown in Fig. 2. The length of the sides is the difference between an ordinate cut off by the top and bottom of the cell — usually equipo-tentials. The coordinates of the points along an equipo-tential or streamline are obtained by Lagrange's8 equation of interpolation for which the constants are coordinate points at the intersections. Three intersections for con-

Jan 1, 1965

In the examination of an undeveloped prospect a decision must be arrived at from an inspection of the outcrops and the exposures in a few shallow pits. Prospects that are offered for sale rarely expose any important quantity of good ore, work having usually been stopped when the immediate exploration no longer yielded favorable results. It should be borne in mind, furthermore, that a great majority of prospects have been examined many times, and if of conspicuous promise, would have been acquired-for development. In most cases the problem for the engineer, therefore, is to discover the traces of a valuable mineralization that has disappeared through solution, or the conditions that indicate the possibility, or probability, of underlying secondary enrichments. The available data being meager, every feature should be the subject of careful study-the condition of the outcrop, the structural relationships, the associations of minerals, the alterations of wall rocks, the chances for underlying enrichments, and so forth, as well as the actual assay value of the material exposed. It is frequently advisable to spend the time and money necessary to have trenches dug at various significant points along a promising outcrop; such exposures, even if the depth attained is slight, often disclose conditions that are not apparent at the actual surface, as for example, the existence of soft minerals and the distribution of the various minerals through the mass of the deposit. Trenches also permit samples to be taken from points that were not accessible during former examinations. Strong, persistent outcrops of uniform width may be taken to indicate the probable size and character of the underlying vein,

Jan 1, 1932

By John Batchelder, David W. Blake, Ted. G. Theodore

The Copper Canyon CIL-Au-Ag deposits include two geologically distinct hypogene ore bodies developed primarily in late Paleozoic rocks adjacent to a 38-m.y.old potassic-altered granodiorite, whose emplacement seems to have been controlled largely by the Virgin fault, a north-striking normal fault. Widespread but subeconomic concentrations of sulfides as fracture and cavity fillings in skarn apparently preceded the final intrusion of the granodiorite. In the west ore body, metals reached ore-grade concentrations through the massive replacement of andradite by chalcopyrite, pyrrhotite, and pyrite mineral assemblages. The east ore body probably formed after the granodiorite reached its present level. Data suggest that fluids associated with potassic alteration here were most likely composed of magmatic water mixed with some meteoric water.

Jan 1, 1977

By Charles Hart

THE-report of the advisory committee to the U. S. Bureau of Mines, on the use of oxygen in metallurgy, brings to the art of steelmaking a radical change in the method of operation of the many processes of this widely diversified industry. When completed, the improvements suggested by the use of oxygen will be far-reaching and revolutionary. As to its effect upon the iron blast furnace, the use of oxygen should be as important as any of the improvements in the art of iron smelting and should take its place beside the German "Hochofen" which was the first attempt to use a shaft for preheating the stock, and beside the hot-blast stove which heated the blast before entering the furnace. The former initially produced molten iron and the latter made unbelievable economies in fuel consumption. It would seem that a discussion of this paper would be best served by following the conclusions on page 17 of the report and analyzing them seriatim. 1. (a) A decrease in costs, due to higher smelting heats is only attainable by taking full advantage of these heat units. This is affected by, adding additional ore to the burden which in turn increases production and yields a larger tonnage upon which to figure costs. These economies appear in decreased cost per ton of iron for coke and limestone consumed, and a proportionate reduction in all items entering the cost above materials. We can take no exception to these. premises. It is a well-known fact that silicon in the iron and sulfur removed" are the result of hearth temperature, other matters remaining constant. To a practical furnaceman the most satisfactory manner of controlling a furnace is by increasing the burden. It is not necessary, therefore, to consider the question of refractories, for this discussion presupposes that the temperatures in the furnaces will be kept practically where they now stand for making the various grades of iron. The same situation obtains in regard to the height of the furnace, which, as intimated, was one of the great strides forward in this art, and its abandonment at this time, is inconceivable. The shaft prepares the stock so that at each succeeding step we have exactly the proper conditions. All the stock entering the furnace is dried and preheated. The limestone is calcined by sensible heat practically at no cost, for this is sensible heat which otherwise would pass from the top with the gases. Under normal conditions, external calcination has been attempted without tangible results. Under normal average furnace operation, limestone requires about 760 B.t.u. for calcination and the loss of sensible

Jan 11, 1924

By E. M. Wise

IN a previous communications the improvement in strength, harden-ability and color, occasioned by replacing gold in a typical gold-silver-copper alloy by various amounts of platinum, or palladium, was discussed. In the present paper the results of further studies upon the constitution and the nature of the hardening transformation in these alloys are pre-sented. This research may be summarized as follows: 1. The liquidus and solidus have been determined for the alloys of the palladium and platinum series. Cooling curves were utilized for deter-mining the liquidus of the palladium alloys but this method proved unsuitable for the platinum alloys so that a, novel quenching method was utilized for the latter. Both the liquidus and solidus of the palladium alloys increase steadily with the palladium content. The liquidus of the platinum alloys increases rapidly with the platinum content, while the solidus temperature increases with the platinum content up to about 14 atomic per cent platinum, but suffers no further increase with additional increments of platinum up to 20 atomic per cent at least, owing to a peritectic reaction. 2. Palladium, and even more effectively platinum, reduces the rate of grain growth. Owing to this fact and to the increase in the solidus temperature, "overheating" does little or no damage to alloys containing reasonable quantities of these elements. This is confirmed both by tensile tests and metallographic examination. 3. The excess phase present in one of the high-platinum-content alloys has been isolated and chemically analyzed and was found to consist almost wholly of platinum, gold, and copper, evidently derived from the compound AuCu, by the partial replacement of gold by platinum.

Jan 1, 1933

By G. Caetani, E. Burt

Jan 1, 1907

By O. C. Ralston, William C. Hunter

DUring experimental study on the separation of a zinc concentrate from the heavy sulfide ores of Jerome, Ariz., a great deal of attention has been given to proper activation of the sphalerite content of the ore. The sphalerite at Jerome contains enough iron to class it as a marmatite, as picked specimens have only about 60 per cent. zinc, whereas pure zinc sulfide contains 67 per cent. zinc. This marmatite in large pieces is black in color, but in dry powdered state is brown. A flotation froth made from it has a silvery black luster in comparison with a brassy luster caused by chalcopyrite which occurs in the same ores. The sample used in most of the experiments described below consisted of about 3000 Ib. of diamond-drill core from the zinc-bearing orebodies of the United Verde mine, and had the following analysis: Per Cent. Per Cent. Oz. peR Ton Cu............... 0.695 Al2O3............ 0.83 Ag................. 1.30 Zn............... 6.17 S................ 43.35 Au................ 0.02 Fe...............36.23 CaO............. 0.46 SiO2............. 9.27 Mineralogically, this analysis is calculated to the following, which is in agreement with the microscopic examination: Per Cent. Per Cent. Chalcopyrite................... 2.0 Schist........................... 3.2 Marmatite..................... 10.32 Quartz........................... 8.2 Pyrite........................ 73.0 Calcite.......................... 0.9 All samples were ground in a laboratory ball mill in order to leave about 3 per cent. on a 200-mesh sieve, fine grinding being essential to liberate the minerals in the ore. Most of the Jerome ores are so intimately crystallized that reasonably complete unlocking by grinding does not take place until 800 mesh is approached. Therefore, the 200-mesh grind adopted contains a considerable amount of locked mineral grains, but not so much as to render impossible the preparation of commercial grades of concentrate.

Jan 1, 1930

By T. M. Kegley, J. H. Frye, D. L. McElroy, M. L. Picklesimer, E. E. Stansbury

Measurements of rate of growth, thermodymmic quantities, and partitioning of Mn are reported for high-purity eutectoid Fe-C and Fe-C-Mn steels for the auistenite-pearlite reaction. Evaluztion of the cotnstants of a derived-rate equation with these data indicate that Mn additions cause the decrease observed by increasivg the activation energy and apparent activation entropy or the movenment of complexes at the interface. A diffusion-controlled mechanism is not required. Appreciable partitioning of Mn to cementite occurs entirely behind the austenite-pearlite interface for more than 30°C of subcooling. ThE growth of pearlite from austenite has been extensively studied over a period of years. but the rate-controlling step in the process is not known nor is the mechanisrn of the effect of alloying elements understood. A comprehensive review of the subject has been given by Mehl and Hagel. The present study has been concerned with further considerations of the effects of alloying elements on the rate of growth of pearlite. Analytical relatioriships for the rate of growth of pearlite have been considered by Zener.2 Turnbull,3 Machlin,4 Cahn.5 Frye,6 and Frye et a1.7 The derived expressions in each case involve the free energy of the transformation. the interlamellar spacing. and some rate term of the nature of the diffusion coefficient. mobility or frequency of occurrence of some rate-determining step. The treatments. of course. differ in detail. Further consideration is given in the present paper to the equation of Frye, Stansbury. and McElroy which was derived from modified absolute rate theory without in any way specifying the mechanism of the reaction. This equation is r=c ? T ? F exp -?E*/RT [1] where r = rate of growth in mm/sec c = a constant AT = equilibrium transformation temperature minus actual transformation temperature "C ?F = free energy per mol of austenite minus that of pearlite ?E* = activation energy R= gas constant ?F in Eq. [1] is computed from the following: ?F=?H?T/To - ?T' dT' ?T' ?CdT"/T" [2] To To where AH is the enthalpy per mol of austenite minus that of pearlite at the equilibrium temperature, To, and AC is the difference in specific heat between austenite and pearlite per mol. Subsequently, Darken, Fisher, and Galligan8 have reported that a layer of ferrite separates pearlite from austenite at the growing interface (i,e., the advancing face of Fe3C is in contact with ferrite, not austenite) and the ratio of the thickness of this layer to the spacing of the pearlite has not been found to vary with alloy content or transformation temperature. This observation does not require any alteration in the above equation: however, it may require that a different significance be attached to the factor, AT. The AT term appears in Eq. [I] as a consequence of a factor for the amount of growth per complex transformed at the interface.* It is based *This is not the sole reason for expecting such a relationship. See Ref. 7._______________________________________________________ on a l/2 ?T dependence of the interlamellar spacing. Zener2 has developed a theory which leads to Soa 1/?V where So = the pearlite interlamellar spacing. This relation is as consistent with the data on interlamellar spacing as other relationships, although, as pointed out by Mehl and Hagel,1 the data are not sufficiently precise to consider the relationship as confirmed. The work of Darken, Fisher, and Galligan8 requires that the above be written where f = the thickness of ferrite layer between austenite and pearlite. The present paper is concerned with iron-carbon-manganese eutectoid alloys and reports experimental measurements of the following kinds: 1) the effect of

Jan 1, 1961

By H. D. Newell

THERE has been much research and commercial development in recent years in the use of chromium and nickel in steels of various types, including those intended for high-temperature service. By "high-tem-perature steels" are meant those specifically designed for service at ele-vated temperatures in steam plants, oil refineries and other industries where high-temperature operations are conducted. This paper is devoted to some preliminary data on the effect of silicon on certain of the most popular chromium-molybdenum steels now being used in quantity by the refining industry and includes a short statement on the influence of copper in steels intended for high-temperature service.

Jan 1, 1937

By A. Eilers

The use of the bag-house for filtering out fumes produced in certain metallurgical operations is not new in America. There are no patents in force at this time, to my knowledge, which might hinder such use. Up to about 25 years ago the bag-house was only employed in connection with either zinc-works, which produced the oxides, to be sold for paint, or as an auxiliary in extracting lead from high-grade oxidized ores and from galena-concentrates in the Missouri and neighboring lead-regions; this work being then done in the Scotch or American hearths and in very low slag-furnaces, in all of which was produced an excessive amount of oxides which were also finally sold as paints. The literature1 on the above is abundant in text-books and periodical publications. The first large bag-house to be used permanently in connection with lead blast-furnaces was erected, as far as I am aware, about 1887 at the Globe smelting Co.'s works at Denver, Colo., under the Lewis-Bartlett patents. The brick flue, running from the blast-furnaces to the bag-house, was only a few

Jan 1, 1913

By J. M. Bugbee

The engineer and the conservationist agree that effective water drive is the desirable reservoir production mechanism. Water drive may result either from the expansion of edge water, the reservoir water bordering an oil pool, or from the artesian flow of edge water from the outcrop. Thus, the extent of the reservoir has an important bearing upon both the rate and the ultimate quantity of water influx to an oil pool. Lens-type reservoirs are generally recognizable, but the complete structure of the more important domal types, having possible limitations from crestal and synclinal faulting, is not well understood. The delineation from cores, electrical logs and exploitation phenomena of the crestal portions of reservoirs is increasingly exact. This paper suggests that inference from these factual pictures, combined with the scattered well and geophysical data of the synclines and with consideration of the dynamics of structural formation, may be applied to solving the complete geologic structure. Since faulting on the domes and in the synclines may effectively seal and thus limit the size of a reservoir and bar additional water influx, consideration of geologic structure and its possible effects is essential to complete analysis and prediction of reservoir performance. Introduction Implicit in reservoir studies is the fact that the oil must be displaced from the reservoir rock by some other fluid, either gas or water, and this understanding yields the terms descriptive of the major reservoir production mechanisms, gas expansion and water drive' Three recent papers1-2-3 make clear the economic and conservation preeminence of Water drive as a production mechanism; in fact, the title of the latest of these is " Production under Effective Water Drive as a Standard for Conservation Practice." There appears to be an assumption at times among analysts that the effectiveness of a water drive is solely dependent on the rate of oil production; that is, if water drive appears to be insufficient or lacking, a lower oil-recovery rate would increase or reveal it. This assumption might result from the fact that the analysis has been wholly developed during the period of production curtailment; that is, since 1929. The writer takes it that the recurrent phrase in De Golyer's paper,3 "some degree of water drive," is related to this assumption. In California, an extraordinary phrase, "inactive water drive," is rather common and the connotation of uncertainty regarding our knowledge of reservoir performance is evident. Wyckoff2 speaks of the type of reservoir and performance as follows: "In general, reservoirs may be any one or a combination of domal, faulted, lenticular, or stratigraphic traps. Insofar as the dynamic performance of such reservoirs is concerned, the particular type merely determines whether regional flow is symmetrical as in a uniformly developed domal or lenticular type, or one-sided as in many stratigraphic or faulted traps." But whether the flow is

Jan 1, 1943

By J. M. Bugbee

The engineer and the conservationist agree that effective water drive is the desirable reservoir production mechanism. Water drive may result either from the expansion of edge water, the reservoir water bordering an oil pool, or from the artesian flow of edge water from the outcrop. Thus, the extent of the reservoir has an important bearing upon both the rate and the ultimate quantity of water influx to an oil pool. Lens-type reservoirs are generally recognizable, but the complete structure of the more important domal types, having possible limitations from crestal and synclinal faulting, is not well understood. The delineation from cores, electrical logs and exploitation phenomena of the crestal portions of reservoirs is increasingly exact. This paper suggests that inference from these factual pictures, combined with the scattered well and geophysical data of the synclines and with consideration of the dynamics of structural formation, may be applied to solving the complete geologic structure. Since faulting on the domes and in the synclines may effectively seal and thus limit the size of a reservoir and bar additional water influx, consideration of geologic structure and its possible effects is essential to complete analysis and prediction of reservoir performance. Introduction Implicit in reservoir studies is the fact that the oil must be displaced from the reservoir rock by some other fluid, either gas or water, and this understanding yields the terms descriptive of the major reservoir production mechanisms, gas expansion and water drive' Three recent papers1-2-3 make clear the economic and conservation preeminence of Water drive as a production mechanism; in fact, the title of the latest of these is " Production under Effective Water Drive as a Standard for Conservation Practice." There appears to be an assumption at times among analysts that the effectiveness of a water drive is solely dependent on the rate of oil production; that is, if water drive appears to be insufficient or lacking, a lower oil-recovery rate would increase or reveal it. This assumption might result from the fact that the analysis has been wholly developed during the period of production curtailment; that is, since 1929. The writer takes it that the recurrent phrase in De Golyer's paper,3 "some degree of water drive," is related to this assumption. In California, an extraordinary phrase, "inactive water drive," is rather common and the connotation of uncertainty regarding our knowledge of reservoir performance is evident. Wyckoff2 speaks of the type of reservoir and performance as follows: "In general, reservoirs may be any one or a combination of domal, faulted, lenticular, or stratigraphic traps. Insofar as the dynamic performance of such reservoirs is concerned, the particular type merely determines whether regional flow is symmetrical as in a uniformly developed domal or lenticular type, or one-sided as in many stratigraphic or faulted traps." But whether the flow is

Jan 1, 1943

By S. S. Marsden, S. A. Khan

Externally generated foam was injected continuously into short porous media. Both flow rate and pressure drop were measured. Liquid saturation was determined by electrical conductivity. Foam yuality I, expressed as the ratio of gas volume to total volume, was varied from 0.70 to 0.96. As measured with a modified fann VG Meter, apparent viscosity of this foam µa decreases with increasing shear rate but usually falls within the range of 50 to 500 cp. At a given shear rate, µa increases almost linearly with I-. When measured with a Bendix Ultraviscoson, kinematic pa is independent of V but absolute pa increases with T from about 3 to 8 cp. The effective permeability -apparent viscosity ratio ke/µa decreases almost linearly with V for porous media of high permeability, but the rate of decrease becomes less for tighter ones. The relative permeability-apparent viscosity ratio kr/µa us V data does not fall on a single line. The kr/µa ratio increases with liquid saturation in the porous medium and with surfactant concentration. Estimates of pa for foam in porous media vary from 30 to 100 cp. INTRODUCTION Although research on the development of a foam-drive, oil recovery process has been going on for almost a decade, most of the significant publications have appeared within the last several years. This illustrates well the rate at which interest in this process is accelerating. Bond and Holbrook 1 were the first to describe the use of foam to improve oil recovery in their patent of 1958. They proposed that an aqueous foaming agent slug be injected into the formation and that this be followed by gas to produce a foam in situ. Fried 2 studied the injection of foam into porous media which had already been subjected to conventional gas or water drives and found that gas could be used to drive a foam bank which would, in turn, displace additional oil in the form of an oil bank. He attributed the increased oil recovery to the high effective viscosity of foam flowing in porous media. His microscopic observations showed the importance of foam generation and regeneration within the porous medium. By injecting both air and aqueous surfactant solution, Bernard3 generated foams within the porous medium in which oil displacement was being studied. In a separate empirical test, he also measured the dynamic foaming characteristics of the same surfactants in water and/or oil. With some exceptions and for the seyen surfactants studied, there seems to be a qualitative relationship between the efficiency of liquid rlisplacrment and the dynamic foaming testtsed. This relationship was not consistent enough to eliminate the necessity of actual foam flood tests in porous media for surfactant selection. In a study basic to gas storage in aquifers, Bennett4 described the displacement of brine by foam in consolidated porous media. Among other things, he stated that the ability of a surfactant solution to foam is more important than the stability of its foam. The presence of a foam bank between the displacing air and the displaced brine improved both breakthrough and ultimate recovery. In a continuation of this work Kolb5 attributed the great reduction in surfactant solution production rate as displacement by air progressed to a decrease in relative permeability to gas. These several effects reported by both Bennett and Kolb can all be attributed to the high apparent viscosity of foam which was obviously flowing in the porous media. Bernard and Holm6 observed that gas permeability in the presence of foam was much less than in the absence of foam when both were measured at the same gas saturations. This reduction in permeability was proportionately greater for more permeable sands and sandstones than for the less permeable. Viscosities of the surfactant solution and air were used for their calculations rather than apparent foam viscosities. The foam stability increased with decreasing permeability, which was probably due to the natural regenerative properties of porous media, and the permeability reduction increased

Jan 1, 1967

By H. l. Burghoff, E. C. Bohlen

The work reported in this paper was carried out to supplement the existing information concerning directional properties and recrystallization textures of annealed brass sheet and strip. These characteristics are of direct interest when the forming and drawing properties of such material are being considered. Among those who have made contributions in this field are Bass and G1ocker;l Bauer, Göler and Sachs;2 Phillips and Samans;3 Pratt;4 Price;5 Cook;6 Richards;7 Brick;8 and Brick and Williamson.9 These investigators have found, in general, that in brass strip that shows directional variations in properties, tensile strength has a minimum value and elongation has a maximum value at 45' to the rolling direction. The most pronounced directional properties have been found in material given the greatest reductions in rolling followed by high annealing temperatures. Recrystallization texture of brass has been variously reported as (II3)[II2], (ooi)[ioo], and a combination of (II0)[II5] and traces of the primary rolling texture, (110)[112]. The directional studies have been very informative, but actual tests appear to have been confined to material in its final condition. Tests at intermediate stages have received little attention although previous history of some materials has been partly considered. Perhaps the most comprehensive investigation was made by Cook,' who studied the directional properties of 70-30 brass strip for which the final and penultimate, or next to the last, anneals and the final reductions were varied. He found that, for any given combination of penultimate anneal and final reduction, the tendency toward the development of directional properties was reduced as the temperature of the final anneal was decreased. In addition to drawing cups and making tensile tests of the finished material at various angles to the rolling direction, he measured the frequency and the angles of twins in grains for several specimens. Plots of his twin counts showed directionality for the materials that produced eared cups. Test Materials and Equipment For this investigation, one commercial heat of 68-32 brass was cast in the form of bars for cold-rolling, I31/2 in wide and I1/2 in. thick. The analysis was as follows: 68.83 per cent copper, 0.04 per cent lead, 0.01 per cent iron, 31.12 per cent zinc (by difference). The bars were so processed to the final thickness, 0.020 in., as to obtain on this thickness all possible combinations of the variables listed below except those involving the sequence of 84 per cent penultimate reduction and 84 per cent final reduction: I. Penultimate reductions of 37 per cent, 50 per cent and 84 per cent; 2. Penultimate anneals at 800°, 900°, 1050° and 1200°F.; 3. Final reductions of 37 per cent, 50 per cent, 69 per cent and 84 per cent;

Jan 1, 1942

By E. C. Bohlen, H. l. Burghoff

The work reported in this paper was carried out to supplement the existing information concerning directional properties and recrystallization textures of annealed brass sheet and strip. These characteristics are of direct interest when the forming and drawing properties of such material are being considered. Among those who have made contributions in this field are Bass and G1ocker;l Bauer, Göler and Sachs;2 Phillips and Samans;3 Pratt;4 Price;5 Cook;6 Richards;7 Brick;8 and Brick and Williamson.9 These investigators have found, in general, that in brass strip that shows directional variations in properties, tensile strength has a minimum value and elongation has a maximum value at 45' to the rolling direction. The most pronounced directional properties have been found in material given the greatest reductions in rolling followed by high annealing temperatures. Recrystallization texture of brass has been variously reported as (II3)[II2], (ooi)[ioo], and a combination of (II0)[II5] and traces of the primary rolling texture, (110)[112]. The directional studies have been very informative, but actual tests appear to have been confined to material in its final condition. Tests at intermediate stages have received little attention although previous history of some materials has been partly considered. Perhaps the most comprehensive investigation was made by Cook,' who studied the directional properties of 70-30 brass strip for which the final and penultimate, or next to the last, anneals and the final reductions were varied. He found that, for any given combination of penultimate anneal and final reduction, the tendency toward the development of directional properties was reduced as the temperature of the final anneal was decreased. In addition to drawing cups and making tensile tests of the finished material at various angles to the rolling direction, he measured the frequency and the angles of twins in grains for several specimens. Plots of his twin counts showed directionality for the materials that produced eared cups. Test Materials and Equipment For this investigation, one commercial heat of 68-32 brass was cast in the form of bars for cold-rolling, I31/2 in wide and I1/2 in. thick. The analysis was as follows: 68.83 per cent copper, 0.04 per cent lead, 0.01 per cent iron, 31.12 per cent zinc (by difference). The bars were so processed to the final thickness, 0.020 in., as to obtain on this thickness all possible combinations of the variables listed below except those involving the sequence of 84 per cent penultimate reduction and 84 per cent final reduction: I. Penultimate reductions of 37 per cent, 50 per cent and 84 per cent; 2. Penultimate anneals at 800°, 900°, 1050° and 1200°F.; 3. Final reductions of 37 per cent, 50 per cent, 69 per cent and 84 per cent;

Jan 1, 1942