Search Documents

By A. R. Gregory, A. L. Podio, K. E. Gray

Dynamic elastic properties of dry and water-saturated Green River shale samples were computed from compressional- and shear-wave velocity measurements. P- and 5-wave velocity measurements were made in three mutually perpendicular directions with respect to the bedding planes. Measurements were also made in several different directions by varying the angle between the bedding planes and the direction of propagation of the wave for angles of 0, 30, 45, 60 and 909 The oriented samples were subjected to both confining pressure and axial loads, in excess of the confining stress, in the direction of propagation. In general, P- and S-wave velocities increased with increasing stress levels, with a corresponding increase in Young's modulus. Water saturation caused the P-wave velocity to increase and the S-wave velocity to decrease. Elastic moduli decreased upon saturation, except for Pois son's ratio, which increased, indicating some degree of weakening of the material. The samples showed a moderate degree of anisotropy; this was to be expected from the laminated nature and shallow occurrence of Green River shale. INTRODUCTION This paper presents some results of an experimental determination of the elastic coefficients of anisotropic materials (in particular, finely layered rocks and minerals such as Green River shale) from measurements of dilatational and shear-ultrasonic-wave velocities. Ultrasonic techniques have been used extensively in nondestructive testing. Several methods have been proposed by Mcskimmin, 1 and some of these have been used successfully to measure ultrasonic velocities in rocks. Hughes and Cross, 2 Wyllie et al., 3 and Birch 4,5 developed pulse first-arrival techniques for the measurement of dilatational and shear velocities. Williams and Lamb 6 used the method of cancellation of a traveling wave, which was later modified by Myers et al.' and perfected by McSkimmin. 8 Although this method is highly accurate, it has not been used as widely as the pulse-transmission methods recently reported by Jamieson and Hoskins 9 King,10 and Mattaboni and Schreiber. 11 It has been common practice to use some form of crystal transducers, either quartz or ceramic, that has been cut or polarized in different directions in order to generate either compressional or shear waves. However, accurate determination of shear wave velocities has been difficult due to problems that arise in obtaining a pure shear wave from cross-polarized crystals, which usually also generate a small amount of compressional energy. As reported by Gregory, 12 this energy can be seen as a long precursor preceding the sharp break of the shear first arrival. The need for generating pure shear waves led to interest in mode-conversion techniques, which are based upon conversion of the mode of vibration through wave reflection or refraction at a discontinuity. Arenberg13 showed that for certain materials and for certain angles of incidence it is possible to generate pure shear modes by reflection at a boundary. Jamieson and Hoskins 9 used a pyrex glass-air interface for generating pure shear waves, and King 10 used this method successfully for measuring shear-wave velocities in rocks. Gregory l4 arrived at a similar result by refraction of a wave at an aluminum-oil interface. A plane compressional wave, traveling in the oil phase, is incident on the aluminum at an angle larger than the critical angle for compressional waves, and thereby generates a purely transverse, plane-polarized wave in the aluminum. During the last few years methods have been developed that allow the simultaneous determination of shear and compressional velocities in solids.

Jan 1, 1969

By L. A. Panek

Using an approach based on the theory of similitude, the author develops a general equation and related concepts that provide new insights to an old problem. The load-bearing capacity (strength) of a square, rectangular, or cylindrical prism of a brittle material such as rock, coal, or concrete is expressed as the mathematical product of a size effect, a shape effect, and a function of the mechanical properties (deformability, cleat/joint spacing, and friction) of the pillar, roof, and floor materials. Through an application of multivariate statistical analysis, the results of assorted tests (laboratory and in situ) and observations of failed pillars can be combined into a fundamental scaling equation, which provides a unified, consistent approach to the estimation of mine pillar strength. The form of the equation is sufficiently general to be able to incorporate refinements in the characterization of the structural parameters, as they become available through future analysis and experimentation. Analysis of the published test data suggests that pillar compressive strength (per unit of area) is proportional to the cube root of the pillar width, and that the height effect can be described as the superimposing of a variable size effect (characteristic of the material) on the constant width effect.

Jan 1, 1981

By T. Egleston

The necessity of using a refractory material capable of much greater resistance to chemical action and having a far higher melting-point than those which contain silica, which melt and sweat off in the furnace even when not exposed to bases forming with silica more or less fusible compounds, has led to a careful practical study of all those materials which contain very refractory bases. The results of these researches, extending over several years, and made on a very large scale in many of the largest works in Europe, are of the highest interest, not only considered as a step in the progress of the study of the materials themselves, but in the application of refractory materials to metallurgical uses in general. The result of the experience of the last seven years with these basic materials, as in general with all such substanccs, is that natural products cannot be used as such. They are either too uncertain in their quality, contain substances which may in certain cases be very injurious, or, when in a condition in which they might be used, are so rare as to become practically unavailable for employment on a large scale. The materials that may he used are therefore not only limited in number. but they must be prepared artificially. When the use of basic artificial material is further extended, no doubt the number of these substances will not only be greatly increased, but the methods of preparation will be both perfected and cheapened to such an extent as to permit their application in processes for which they have hitherto proved too expensive. The quantity of refractory materials required for making ingots will he from 130 to 150 Ibs. per ton, or between 6 and 8 per cent. of the metal produced. In an establishment producing 2000 to 3000 tons of steel per week, considerable space is required to handle the basic materials properly. It is proposed in this paper to briefly discuss these basic materials and their application in the only two metallurgical processes where they have as yet been applied. These are the basic Bessemer and the basic open-hearth process, known as the Thomas-Gilchrist processes.

Jan 1, 1886

By V. Apraxine, J. Lakaye, J. J. Saquet, P. Troch

Union Minière du Haut-Katanga owns concessions for extracting copper and associated metals in the high plateau region of Katanga. The concession is about 188 miles long by 44 miles wide and has three principal areas: Southern area-The Prince Leopold mine is an underground operation from which a copper-zinc sulfide ore is extracted. The mine and associated concentrator are at Kipushi. Copper concentrates are smelted and converted to blister copper at the Lubumbashi smelter at Elizabethville.

Jan 12, 1962

By W. S. Owen, T. Bell

The variation ox the M, temperature with nitrogen concentration has been determined experinzentally. The free-energy difference between martensite and the parent y Phase at the M, temperature,is computed for Fe-C and Fe-N alloys using recent solubility data fm the Fe-N system and new data for the variatim of the activity of the interstitial solute in the y phase with concentration. The "geometric model" is considered also, and the importance of Zener ordering is noted. It is shown that, although at any chosen concentration the M, temperature and the activity are significantly different in the two alloy systems, the free-energy duference is the same within the limits of experimental error, thus Providing further evidence of the very close similarity between the martensite transformations in Fe-C and Fe-N alloys. TO estimate the free-energy change accompanying the martensite transformation in binary interstitial alloys it is necessary to know the variation of the Ms temperature with interstitial solute concentration and some thermodynamic data. To date, only the Fe-C system has been discussed because this was the only system for which relevant experimental measurements had been made, but even in this case the data available are insufficient to permit the free-energy change to be calculated without the assumption of a thermodynamic model for the y and a solid solutions. The last comprehensive discussion of the topic was by Kaufman, Radcliffe, and Cohen in 1.960.' Since that time Ellis, Davidson, and Bodsworth2 have redeter mined the activity of carbon in y iron as a function of carbon content and Atkinson3 has measured the activity of nitrogen in Fe-N austenite. The M, temperature of Fe-N is reported in the present paper. Thus, it is now possible to assess the free-energy change accompanying the martensite transformation in Fe-N alloys on the same basis as that used to assess the change in Fe-C alloys. This comparison is of interest because it has been shown recently4 that the structure of the martensite formed in Fe-N alloys changes with nitrogen content in a manner exactly parallel to the changes in structure in the Fe-C series and that the strain associated with the distortion of the iron lattice in either the y or the a phase by a nitrogen atom is the same as that produced by a carbon atom. The work to be described tests whether or not this close similarity between the two systems extends to the thermodynamics of the martensitic transformations. THE Ms TEMPERATURES FOR Fe-N MARTENSITE Bose and Hawkes5 found the M, temperature of a eutectoid Fe-N alloy (2.35 wt pct N) to be 35°C. This single determination appears to be the only reported measurement of the M, temperature of an Fe-N alloy. In the present work a series of more than fifteen different specimens containing between 0 and 2.7 wt pct N were prepared by controlled nitriding of pure iron wire 0.010 in. diam. The iron was supplied by B.I.S.R.A. and was designated ACN2. The nitriding procedure, all aspects of which are critical, has been described in detail elsewhere.' Each specimen was quenched from the austenitizing temperature into brine at 20°C without removing the specimen from the ammonia-hydrogen atmosphere in which it was ni-trided. Alloys containing up to 0.7 wt pct N were fully martensitic. More concentrated alloys contained progressively more retained austenite. At 2.34 wt pct N the specimen was completely austenitic after quenching to 20°C. The M, temperature of specimens with M, temperature above 20°C (those containing less than 2.35 wt pct N) was determined by a thermal arrest technique. For the more concentrated alloys (2.35 to 2.70 wt pct N) the variation of electrical resistance with temperature down to -196°C was used. Unlike Fe-C alloys, Fe-N alloys cannot be reaus-tenitized in vacuum or in an inert atmosphere because excessive loss of nitrogen occurs, even in short times, at high temperatures. Consequently, the alloys were reaustenitized in the ammonia-hydrogen mixture corresponding to nitrogen equilibrium at the temperatures used. The specimens were quenched in a blast of cold hydrogen gas and the temperature, measured by a thermocouple welded to the 2.5-in.-long specimen, was recorded on a high-speed recorder. In the first experiments 0.002-in.-diam chromel-alumel wire thermocouples were used but it was found that these gave erroneous readings due to contamination by nitrogen pickup. Pt-Pt 13 pct Rh wires of 0.002 in. diam were found to be satisfactory. Further details of the experiments are available in the original thesis.7 The cooling rate was controlled between 400° and 4000°C per sec by adjusting the hydrogen pressure. At least three cooling curves were obtained for each composition. Each specimen was analyzed for nitrogen after quenching. To aid in the accurate location of the martensite arrest points a series of cooling curves of 0.010-in.-diam platinum wire were recorded and these, which did not contain an arrest, were used as comparison standards. Four specimens, each in the form of a 3-in. loop, were prepared from each of the four alloys containing more than 2.35 wt pct N. One specimen was used for nitrogen analysis, one for X-ray diffraction, and two for resistance measurements below 20°C. The latter specimens were quenched from 20°C into constant-temperature baths at selected lower temperatures.

Jan 1, 1968

The Institute is custodian of funds for support of numerous gold medals and prizes and has representatives on boards awarding still others. Details regarding the Institute Awards are given below. The Institute is represented on the boards of the John Fritz Medal, the Hoover Medal and the Washington Award, in connection with the three national societies of Civil, Mechanical and Electrical engineering; and, also, in the case of the Washington Award, with the Western Society of Engineers. The Institute is represented with these four societies on the committee in charge of the Alfred Noble Prize.

Jan 1, 1939

By William R. Webster

This is a subject which our Institute has made peculiarly its own. In the first volume of its Transactions the analysis of steel received attention, and every subsequent volume has borne witness to the acuteness and industry of our members in the investigation of this subject. The keynote mas struck, in this as in so many other lines of progress, by A. L. Holley, in his paper on " Tests of Steel," read at the Easton meeting of October, 1873 (Trans., ii., 116)—an essay which may rank as a classic by reason of .its elegant form, logical force, and clear prevision of all the bearings of its theme, Taken together with the brief report of the discussion which followed it (in which Dr. Drown emphasized the effects of heat-treatment and mechanical handling, and Dr. Sterry Hunt the importance of minute variations in chemical composition, and of possible isomeric and allotropic conditions), it constitutes, after the lapse of twenty-five years, an admirable and adequate introduction to the long list of technical papers which have succeeded it. Three years later came the epoch-making papers of Dr. C. B. Dudley on the relation between the chemical composition and physical properties of steel rails, which, with the voluminous discussion they evoked, constitute a special volume, published by the Institute, and full of useful suggestions. If Dr. Dudley could be induced to resume this investigation, he would doubtless be able to solve many points still uncertain or disputed. But I cannot undertake to review the history of this subject, as represented in our Transactions—still less to restate all the contributions to it which have been made in books or in papers before other technical societies, since the initiative was taken by the Institute. My more modest purpose is to indi-

Jan 1, 1899

By J. P. Murphy, T. E. Leontis

DURING the last few years, the trend in the aircraft and automotive industries has been toward higher and higher operating engine temperatures. This has created considerable interest in the effect of temperature on the properties of alloys. In the magnesium field, it has been recognized for many years that the addition of cerium imparts high strength and good resistance to creep at elevated temperatures. Beck,1 in his treatise on-magnesium, has summarized the work of German investigators. This includes the unpublished data of Menking, showing the increase in strength and hardness of extruded alloys containing 2 to 20 per cent Ce at temperatures from 200 to 300°C. (68° to 572°F.) and the results of Vosskühler, who demonstrated the improved resistance to creep of alloys containing 6 per cent Ce plus 2 per cent Mn and 0.5 per cent Ce plus 2 per cent Mn at 150°C. (302°F.). Wellinger and Keil2 have also reported the creep properties of a forged magnesium-cerium-manganese alloy at 200° and 250°C. (392° and 482°F.). Haughton and Prytherch have determined the tensile properties of various forged magnesium alloys containing cerium, cerium plus manganese, cerium plus calcium, cerium plus nickel, cerium plus nickel plus manganese, and cerium plus cobalt plus manganese at temperatures up to 290°C. (554°F.). Magnesium-cerium alloys have been used in some commercial applications. It is reported that an alloy containing 3 per cent Ce plus 0.5 per cent Mn plus 0.5 per cent Ca is being used on a forged impeller in Great Britain. Two forged parts made from an alloy with a nominal composition of 5 per cent Ce and 2 percent Mn have been found on the German .BMW-801D aircraft engine. These two forgings consist of a supercharger impeller and a rear cam-follower guide. In this country, several types of pistons have been made experimentally in both .the cast and the forged conditions from an alloy containing 6 per cent Ce plus 2 per, cent Mn and in the cast condition from an alloy of magnesium plus 10 per cent Ce. The cast pistons have been tested in various types of internal-combustion engines, with promising results. This paper presents the results of an extensive investigation on the properties of various cerium-containing magnesium alloys in both the cast and the forged conditions. Data are presented to show the beneficial effects of increasing amounts of cerium on the mechanical properties of magnesium at elevated temperatures. The effects of heat-treatment on the properties of these alloys and the attendant changes in the microstructure are discussed. The

Jan 1, 1946

By Wing L. Lew

LEAD, silver, and zinc, in quantities of economic importance are found in the Aguilar ore. The lead occurs as galena and the zinc as sphalerite and marmatite. The silver occurrence is more complex. Pyrargyrite and proustite have been identified only occasionally. Galena is silver-bearing and so are the various other sulphides, though to a lesser degree. The principal nonsulphide gangue minerals include calcite, quartz, wollastonite, rhodonite, and various calcium, aluminum, and iron silicates. A typical analysis of, the ore is: Pb, 11.2; Zn, 12.3; Fe, 4.4; Mn, 2.2; Cu, 0.15; S, 11.2; CaO. 7.6; "Insoluble," 50.1 percent; and Ag 263 g per ton. Crushing is done in three stages. The primary crusher at the mine is set to deliver about a 5-in. product. The crushed ore is then transported to the secondary crushing plant by a 3-km cableway where the general practice is to hold the product of the first Symons to about 1 in., and of the second Symons to about 1/2 in. When the ore is soft and rich the product of the first Symons is by-passed directly to the ball-mill bins. Dust control in the secondary crushing plant is effected by enclosing the dust-emanating sources and exhausting the enclosures with a Clarage No. 18 fan driven at 1300 rpm by a 20-hp motor. Use is also made of spray water at one or two critical places. Every effort is made to keep the air free from visible dust. Dust counts taken at the working places show dust concentrations of less than six million particles ner cu ft. The composition

Jan 1, 1947

By R. J. P. Lyon, A. E. Prelat, H. Lawrence

Introduction In 1977, the US Bureau of Mines awarded a grant to the state of South Carolina to explore the possibility of using Landsat multispectral scanner (MSS) data as an aid in monitoring surface mining activities in selected counties of the state. Work had been done in Aiken County prior to the grant by USBM and state personnel at the EROS Data Center using both the GE Image 100 and ESL IDIMS systems. The initial work on the 1:100 consisted of locating and measuring the areas of various kaolin mines. The results were excellent on location, identification, and accurate area measurements of several mines as compared with aerial photos of each mine. The effort also included locating and measuring the size of all mines (including sand and gravel) within two US Geological Survey (USGS) 7 % - min quadrangle maps. Line printer overlays using the IDIMS equipment and software resulted in the location of all known mines within an estimated error less than zt 91.4 m. Mine acreage was calculated by counting each symbol (which represented one pixel) and multiplying by 1.1 (the number of acres per pixel). [Fig. 1] shows a portion of one quadrangle overlay. [Table 1] gives a comparison of acreage measured for several mines from the 1-100 and IDIMS system vs. aerial photo measurements. The success of the preliminary work resulted in the South Carolina Land Resources Conservation Commission submitting a proposal to USBM for funding to expand the scope of work to other mineral mining operations within the state and determine if Landsat Imagery could be used to accurately locate and measure mining and reclamation activity on a continuing basis. Three separate tasks were proposed for selected kaolin mines in Aiken County: Task 1, to measure changes in active mine developments over the period 1974-77; Task 2, to measure reclamation activity, and, if time permitted, seasonal changes in mine signatures over the same period of time; and Task 3, to classify one complete mining operation (i.e., differentiate between active, spoil, overburden, water, reclaimed portions and surrounding terrain. The major effort was centered around J.M. Hubeis Richardson mine. Mining operations were progressing in a northerly direction and included three areas of reclamation: one prior to 1974; one started during early 1974; and one reclaimed during 1976. A discussion of all work done under the grant is available in the March 1979 Final Report listed under References. Computer compatible tapes (CCTs) containing MSS data from Landsat Path 18, Row 37, were purchased from the National Aeronautics and Space Administration (NASA) covering the period February 1974 through January 1977. The MSS data were processed on the General Electric Image 100 using parallelepiped classification at the EROS Data Center's Data Analysis Laboratory, Sioux Falls, SD, and at the Stanford Remote Sensing Laboratory, Stanford University, Palo Alto, CA, utilizing both an unsupervised classification (ISOMIX) and a supervised classification (sequential discriminant analysis). Studies at Stanford University Remote Sensing Lab (SRSL). In Feburary 1977, initial work was begun at Stanford using the STANSORT computer program running on a DEC PDP-10 (Honey, Prelat, and Lyon, 1974). This software is fully interactive and designed to study Landsat CCT data at high resolution (small areas) on a pixel-by-pixel basis (Lyon, 1977). Unsupervised Classification. The initial step was to locate the Richardson mine on the positive print of the full Landsat scene from CCT 1644-15252, dated 6/17/74. This was relatively easy due to a large abandoned kaolin mine and a long narrow pond clearly visible in the scene. Two unsupervised classifications of the Richardson mine were run using ISOMIX clustering (Honey, Prelat and Lyon, 1974). (ISOMIX essentially follows the interactive clustering procedures of ISOCLS Kan, Holley, and Parker. 1973). Although the classifications were successfully accomplished, it was apparent from the TV display that the results did not clearly define the mine areas. A supervised classification would have to be made in order to clearly separate each portion of the mine. Supervised Classification. This classification was done using the Stepwise Discriminant Program (BMDO7M) which is part of the BIOMED package (Dixon, 1970) and involved the following steps: Training group populations were selected and the digital

Jan 1, 1982

By A. L. Fentress, P. R. Bucky

The purpose of this paper is to present a scientific method for determining the proper span and shape of roof for safe and economical mining; at present, these two vital factors wherever pillars are left to support the roof are determined by local practice or general experience. To develop the method described here, experimental laboratory work was done. The arch adopted was a segment of a circle, a flat roof being considered an arch with an infinite radius. Hitherto, arches have been used underground without the background of stress analysis that generally precedes arch construction on the surface. In many cases results have not been as expected, because of the lack of knowledge of the factors affecting its strength and behavior. A theoretical and experimental study of arches should furnish information that will make it possible to design safe and economical surface structures as well as underground openings. For example, on the subject of mine drifts and tunnels, the present idea is that arching their backs increases their strength; this paper will indicate that this is not always true, and if it can be shown that under certain conditions arching becomes unnecessary an economic saving will result. In room-and-pillar work a question may arise as to whether arching the roof and gobbing the excavated material will result in timber saving, and a decrease in the dangers from falls of roof. It is to be distinctly understood that each mine must be treated as an individual problem, and that answers to these questions and many others can now be found after experimental laboratory data have been obtained. Mine-Arch Structure Fig. 1 shows the elements that affect the strength or behavior of the experimental arch. They are the span, crown thickness, radius of curvature, rise and restraint. The restraint in all cases was made sufficient to cause the arch to fail without displacing the restraining sides. Fig. 2a is a photograph of a model arch prepared for testing in the centri-

Jan 1, 1934

By Kurt Stock

The war caused a demand for enormous quantities of high-grade zinc, which were not available and could not be produced from pure ores in sufficient amounts and in the time required. Redistillation of virgin spelter on a large scale was practiced to supply this demand; this paper gives a full description of the process used by the Oklahoma smelters of the Bartlesville Zinc Co. As the redistillation of zinc has become of historical interest only, having been superseded by the electrolytic process, it was deemed advisable to give expression to this phase of the metallurgy of zinc that, in the past, had never gone beyond laboratory experimentation. THE grades of spelter demanded by the consuming industries were not definitely established until the American Society for Testing Materials undertook to fix specifications, based on the varying percentages of the common impurities (lead, iron, and cadmium) as follows: TOTAL, NOT LEAD, IRON, CADMIUM, OVER. PER PER CENT. PER CENT. PER CENT. CENT. A. High grade 0.07 0.03 0.05 0.10 B. Intermediate 0.20 0.03 0.50 0.50 C. Brass special 0.75 0.04 0.75 1.20 D. Prime western 1.50 0.08 The question which grade was the best for certain purposes and why was left unanswered. The conservatism of the zinc-smelting industry and the unwillingness of the spelter-consuming industries to engage in research work prevented the full benefits being obtained that such standardization promised. The custom smelters, producing spelter in pigs or plates, found it impossible to adhere closely to the established limits on account of the variety of ores treated; and the smelters with long-established and known brands, or those manufacturing their metal into marketable products, like sheet zinc, did not have to abide by the newly established grades based on chemical percentages.

Jan 7, 1924

By W. J. Taylor, H. J. Mutz, A. F. Brock

THE International Kickel Co. of Canada Ltd. operates five underground mines and an open pit. Four of the mines, the Frood-Stobie, Creighton, Murray, and Garson, are on the south range of the Sudbury Basin, map above, within a radius of 10 miles of the city of Sudbury, Ontario. The fifth mine, the Levack, is on the north range of the Sudbury Basin, 30 miles to the northwest of the city. The open pit is operating on surface ores of the Frood-Stobie orebody. Two pits were opened at the Frood-Stobie mine; the Frood section was started in 1938 and the Stobie section in 1942. To meet the heavy demand for nickel during World War 11, open-pit production was accelerated until it constituted over 40 pct of Inco's total tonnage. As a consequence open-pit ore was depleted considerably alhead of schedule; the Stobie pit was completed in the summer of 1951, and it is expected that mining at the Frood pit will be completed in 1953. The major program launched 10 years ago to develop additional underground production as a replacement of open-pit tonnage thus had to be greatly speeded up. This conversion to all-underground mining will be completed within the next two years, and the underground mines will then have an annual hoisting capacity of 13,000,000 tons. One of the new mines in the underground expansion program, the Murray, was brought into production in 1950. Ore production from the new Stobie section of the Frood-Stobie mine was commenced on a limited scale in 1951 and will be increased as the program progresses. Delivery of ore to the new Creighton mill was started in the summer of 1951 from the caving project launched at Creighton mine. When mining was started in the Sudbury district 65 years ago the ore deposits were opened on a small scale and mining methods conformed to a general pattern of small open cast pits, followed by open stopes as mining was extended below the pits. The open stoping methods used were heading-and-bench and shrinkage. In certain cases a type of cut-and-fill mining was used with drywall tramways and dry-wall chutes in the fill. As the mines were deepened,

Jan 1, 1954

By J. D. Rice, P. L. Wearden, W. L. Hensou

Solutions to the unsteady-state partial water-drive reservoir performance problem can be obtained through the use of analogue computers or high-speed electronic digital computers. The solutions that have previously been resolved for use on digital computers, however, demand a knowledge of the aquifer parameters. Generally, the analogue computers now in use do not require this knowledge. A solution is presented herein where the aquifer performance, expressed in terms of difference equations, is related to the reservoir performance as expressed by the modified Scbiltbuis material-balance equation. A numerical procedure for a medium-sized digital computer also is presented in which a solution to the set of equations defining the aquifer and reservoir performance is obtained and the aquifer parameters (permeability and sand thickness) are automatically optimized while simultaneously matching the known pressure behavior. Predicted pressure behavior can be calculated using rates from any assumed future production practice. The procedure provides an output format which presents the cumulative, incremental and average rate of natural water influx, the per cent gas-cap expansion, the calculated reservoir pressure, the measured reservoir pressure, and the difference between the measured and calculated pressures. Results of a test problem are presented in comparison with results obtained by the Bruce Analyzer, Ohio Oil Co. 's Pace General Purpose Analogue Computer, and Sun Oil Co.'s Single-Pool Electronic Reservoir Analyzer. These results indicate that unsteady-state reservoir perlormance for a single-pool system can be adequately simulated by a numerical method employing a digital computer and that the special-purpose analogue computer can be supplanted by this method. INTRODUCTION The numerical approach to the unsteady-state partial water-drive reservoir performance problem heretofore has been limited in that solutions have been resolved only for certain fixed parameters. Also, prior to the advent of high-speed electronic digital computers in the last few years, calculations were so tedious and time-consuming that they ordinarily were neglected, or some other means of obtaining the solutions were used. The analogue approach had been used for obtaining solutions to the transmission-of-heat problem and, consequently, means were developed for applying the electrical analogue to the unsteady-state reservoir performance problem. Bruce submitted a paper for AIME publication in Sept. 1942, in which he described an electronic device (now called the Bruce Analyzer) for analyzing the water-drive performance of any reservoir, based on either steady or unsteady-state flow characteristics. 1 Sun Oil Co. adopted the analogue approach in 1949 and now has two special-purpose high-speed electronic reservoir analyzers in use.2,3 Two main features of Sun's analyzers are (1) the high repetitive rate of reproducing the entire history of reservoir performance cyclically a number of times per second, and (2) the elimination of the necessity of knowing the properties of the associated aquifer. Since the advent of larger and faster digital computers, the possibility of incorporating this second feature into a numerical approach appeared feasible. Previous work has been done and material published covering the application of numerical methods to the behavior of the pressure with respect to time at any point in an associated aquifer? However, the aquifer parameters must be known from some source. The material presented in Ref. 4 has been used to a great degree in developing the numerical method described herein. DIFFERENTIAL EQUATION AND BOUNDARY CONDITIONS The problem of simulating the performance of a reservoir and the associated aquifer is to determine the characteristics of the aquifer such that the

By T. D. Lynch, N. B. Pilling

The development of a proper treatment for shells in conncction with war contracts has brought to our attention the fact that the temperature of the liquid bath in which steel is quenched has a decided influence on the speed of cooling in the case of some liquids and very little in the case of others. Widely different physical results have been obtained by the use of water spray, water immersion, and oil immersion and further experiment has shown that the quenching effect of water used as a spray or an immersion varies greatly with the temperature of the water. The present experiments were undertaken with the idea of obtaining information of a quantitative nature regarding the quenching properties of a number of liquids used commercially in hardening steel. The general features of such cooling media are common knowledge and in the literature may be found records of numerous attempts to evaluate the cooling power of a liquid when used as a quenching bath. Much, if not most, of the data given on this subject is in the form of a simple statement of the time required for a certain heated mass to cool between two arbitrary temperatures when immersed in the liquid, quite regardless of the path of the temperature change. Our own purpose has been somewhat different. We have attempted to isolate that property of these liquids having to do with their ability to absorb heat rapidly, as distinct from the behavior of a considerable mass when exposed to different thermal environments. More specifically, from the data obtained through autographically recorded cooling curves of a small standard mass quenched under various conditions, we have tried to analyze the mechanism of heat absorption by the several liquids, measure the changes in its rate as a function of the temperature of the surface of transference, and ascertain the influence of the temperature of the liquid itself upon both. Without attempting an exhaustive citation of the literature, mention may be made of some of the more important contributions, notably the pioneer work of Le Chatelier,' followed by the extensive investigations

Jan 1, 1920

By D. S. G. Hanson

The Flin Flon Mine has been in production for over fifty years, and current mining is dependent on pillar and remnant recovery. One of the last major blocks of ore, and an important economic entity to the Mine, is the North Main Shaft Pillar. A rock mechanics program was initiated through under' ground instrumentation and other subsequent analyses, to establish the degree of instability as min¬ing progressed. Several studies have been and will be undertaken to evaluate the general stability, and possibly improve the chances of stability during pillar recovery. The North Main Shaft Pillar is immediately bounded by cemented cut and fill supporting rib stopes which inturn are bounded by slag and waste filled stopes. The min¬ing method involves a modified longhole open stoping and slag fil¬ling sequence for each mining block in a general mining upwards scheme.

Jan 1, 1983

By George A. Morrison

The Columbia Chemical Division of the Pittsburgh Plate Glass Co. is at Bar-berton, Ohio, 35 miles south of Cleveland. For many years large tonnages of limestone have been brought to the Barberton plant from distant points. The stone is here burnt in vertical kilns, the resultant product then hydrated and the hydrated lime used in chemical processing. To eliminate the expense of these shipments, the company decided to investigate a limestone bed known to exist on company property at Barberton, where the stone is used. The bed lay at a depth of more than 2000 ft. and was known locally as the "Deep Lime." Chemical analyses of sludge from churn-drill holes made some years ago proved that the limestone was of sufficient purity to warrant diamond-drill exploration. Four diamond-drill holes were put down at well-spaced intervals, to represent fairly an area of four miles by one mile. Cores logged as to chemical and physical conditions were found to compare closely, and to corroborate the earlier evidence that the limestone was of superior quality for chemical use. A plant of 300 tons per hour was subsequently decided upon. SITe The yard at the chemical plant was already so congested that location of the projected mine within its area could not be considered. Eventually a site was selected 2 miles northwest of the plant, near the main line of the Erie Railroad. Here 412 acres were owned outright by the company and stone rights were obtained on 2 50 additional acres. This location required a transportation line of nearly 2 miles (8800 ft.), crossing two major highways, and to avoid interruption of deliveries to the plant, overpasses were planned. Geology The limestone in the immediate vicinity lies about 2200 ft. below the surface. Geologists* identify this stone as Delaware of Devonian age. It is overlain by 18 ft. of unconsolidated (sand and gravel), 100 ft. of water-bearing sandstone, and finally 2080 ft. of shale into which sandstone in thin layers is interbedded. The contact of shale and limestone is abrupt, flat-lying and very pronounced. Berea sandstone, often found at 520 ft., is absent, but Euclid sandstone was encountered, together with a seepage of oil and a small amount of methane gas. The limestone bed itself is 345 ft. thick, and overlies 200 ft. of gypsum. The lower part becomes dolomitic as it approaches the gypsum. A detailed study of the drill cores indicates that the upper 50 ft. are highest in lime and reasonably low in silica. The physical make-up shows several separating cherty layers. These occur at definite horizons and cause distinct partings, which become horizontal planes of

Jan 1, 1946

By S. L. Lopata, E. B. Kula

A variation of yield and tensile strength with direction has been noted in heat-treated 4340 steel which had been warn-worked by rolling in the austenitic condition prior to quenching. Measurements by X-rays showed a preferred orientation of martensite crystals. Various ideal preferred orientations of martensite were calculated by assuming a preferred orientation for austenite and transforming this to martensite by the Kurdjumov -Sachs and Nishiyama relationships. Comparison with the measured preferred orientation showed that the ideal rolling texture for austenite in 4340 steel could be expressed as a (112) [111] texture with a component of (110) [112]. No evidence was found for any fiber axis in the rolling direction, or fop- a (123) [412] texture. The observed martensite pole figures can be adequately accounted for by these ideal austenite textures and by the Kurdjumou-Sachs or Nishiyama transformation relationships between austenite and martensite. ALTHOUGH preferred orientations are found in cold-rolled steel sheet and in many nonferrous metals, they are not generally encountered in wrought, heat-treated high-strength steels, since such steels are generally not cold worked sufficiently to develop a strong texture, and any texture that is present is removed during heat treatment by the phase transformations taking place. This report gives details on a preferred orientation found in warm-rolled and hardened 4340 steel. In a recent study, a special combination heat-treating and working technique was used in which 4340 steel was deformed in the austenitic condition, and before re crystallization of the austenite could occur, quenched to form martensite.' Since the austenite was unrecrystallized, it was cold worked and hence could have contained a preferred orientation which could be transmitted to the martensite on quenching, and this in turn could be manifested as a directionality of mechanical properties. Such a directionality of properties was found as a result of working, and this prompted an X-ray study of the preferred orientation. Literature Survey— Rolling Texture in Face-Cen-tered-Cubic Austenite—M a preferred orientation is found in a rolled and hardened steel, it is first appropriate to consider what texture existed in the austenite as a result of the rolling but prior to the transformation to martensite. The changes taking place as a result of the austenite-martensite transformation are then considered. In view of the instability of austenite in 4340 steel at low temperatures, no direct determination of the austenite texture was made. However, an estimate of the texture for austenite in 4340 steel may be made by considering the textures found for other face-centered-cubic metals. Barrett' has reviewed the rolling textures for many materials. The most common orientation in face-centered-cubic metals has the (110) planes parallel to the rolling plane and the [112] directions parallel to the rolling direction, or (110) [112]. Other orientations found are (112) [111], as well as (100) [001], (110) [001], and others. Beck and his co-workers, using quantitative pole figures, report that (123) [121],3 later corrected to (123) [412],4 better describes the ideal orientation. smallman5 reported that the ideal preferred orientation for high-purity face-centered-cubic metals is (123) [121], but that there is a transition to (110) [112] as solid solution elements are added. The latter texture tends to occur more readily at lower temperatures. This transition between the two textures was explained by differences in the slip characteristics with concentration or temperature. More recently, Jones and Fell6 concluded that the (123) [412] texture for face-centered-cubic metals could equally well be represented by a mixture of (110) [112] and (112) [111] textures, and hence it had no physical reality. From the above results it can be seen that there is no agreement on the "ideal" texture for fcc metals and, hence, no firm basis for assuming a texture for austenite in 4340 steel. Therefore, the orientations (110) [112], (123) [412], and (112) [111] have been considered in the following.* *The (123) [4121 is identical to the (123) [121] rotated 90 deg. Orientation Relationship between Austenite and Martensite—When martensite forms from austenite, certain crystallographic planes of the martensite are parallel to planes in the austenite. This orientation relationship was first determined by Kurdjumov and

Jan 1, 1960

By C. F. Cockrell, H. E. Shafer, J. W. Leonard

A significant technological development is discussed for the processing of certain power plant flyashes that are a problem because they contain a high water-soluble mineral content and yield inferior flyash-based brick. This development is based on the addition of hydrochloric acid to the flyash-bottom ash-sodium silicate blends used for the production of flyash-based structures. Favorable changes are evi-dent in sodium silicate consumption, where about half the amount used for making brick from normal flyash is required, processing costs, and strength and appearance of the resulting freshly formed green and fired structural products. In some high cost in-stances (above the $30 or less per thousand brick estimated for normal flyash), hydrochloric acid additions can replace or reduce other costly additives normally required for problem flyashes. This results in savings of as much as $9 per thousand brick. These developments offer promising possibilities for utilizing problem flyashes as well as flyashes which may come into contact with water soluble sulfur as a result of the eventual application of certain experimental air pollution control processes. Much of the research datal-6 accrued through work by the Coal Research Bureau of West Virginia University for the Department of Interior's Office of Coal Research on converting waste power coal ash to valuable brick and other structural products, can be categorized as follows: (1) general ash-to-brick tech- nology; (2) specific ash-to-brick optimization; (3) pilot plant progress; (4) production cost estimates. A summary of the progress on bench-scale experiments indicates that coal ash can yield two types of brick. An acceptable brick is obtained by mixing 73.6% fly-ash, 23.5% bottom ash and 2.9% sodium silicate solution (dry basis). Depending on the flyash and bottom ash used, optimum brick can be manufactured by mixing 72-77% flyash, 20-25% bottom ash and 2.3-3.0% sodium silicate (dry basis) with Na2O : SiO2 ratio varied according to the composition of the flyash used. These blends are thoroughly mixed and mechanically formed into green brick shapes at pressures ranging from 1000 to the more usual 3000 lb per sq in. The green shapes then are dried and fired at temperatures ranging from 1975-2150°F using clay brick cycles that are shorter than standard. Other findings reported to date indicate that when making optimum brick, it is necessary to carefully control the top size of the moisture-releasing bottom ash so that it falls between 8 and 30 mesh, depending on the flyash used. Moreover, the chemical composition of bottom ash and flyash have been found to be of little significance with the exception of a few problem flyashes which are the subject of this paper. Finally, the pilot plant, which was previously reported under construction, is now in operation. This will indicate, among other things, the cost of brick production, which was earlier estimated for non-problem flyashes at $30 or less per thousand brick. The foregoing bench-scale technology is applicable to all the initially tested ashes as well as to the majority of ashes examined during the course of research. However, a few of the ashes yield green and fired products that may be structurally inferior or unacceptable, necessitating excessive and diverse reagent addition, and/or may be coated with unsightly surface deposits. These problem ashes generally originate in certain areas of Illinois, western Ken-

Jan 1, 1969

By Roy A. Lindgren

SINCE the year 1643, when the first blast furnace in America for treating iron ore was built at Saugus, Mass., out of mica schist quarried in the neighboring district, the procurement of a suitable refractory for furnace lining has been a problem of concern to the operators of furnaces. The stacks built of mica schist continued to smelt iron ore until about 1836, when, according to F. H. Norton, the first firebrick were produced', at Queens Run, Pa. Other writers speak of brick having been molded and burned in Massachusetts about the year 1834. In 1841, Andrew Russell began to produce medium refractory plastic clay brick near East Liverpool, Ohio, that were used for lining blast furnaces'. The well-known Kentucky clay-producing district was not opened up until the year 1871, but since then it has produced a large percentage of the linings for iron blast furnaces. While some strides have been made by the refractories industry during the 100 years that have passed since the first firebrick were produced, it has been only during the last two decades that any real progress has been made towards bettering the product, even though the method of production had improved. Perhaps the fault lies with the user of the brick rather than with the producer, for not sooner demanding a supe¬rior product. During the past 15 years the tonnage produced per lining has increased from 500,000 gross tons to 1,000,000 gross tons, and now some furnaces are producing 1,600,000 gross tons and better on a single lining. It is true that enlarged capacity of furnaces and improved practice have accounted for some of this increase in tonnage, nevertheless better quality in firebrick must be given credit for its share. However, we are not yet ready to say that we have reached a maximum life of furnace lining. We believe that a better product can be produced and that the refractories industries of America will, through their extensive research depart-

Jan 1, 1937