Search Documents

By Augustus Locke

Jan 1, 1923

By Augustus Locke

Jan 1, 1923

By W. Rostoker, H. Nichols

It has been demonstrated in previous work1'2 that wetting of aluminum alloys by liquid mercury can cause fracture to occur with substantial suppression of prior plastic flow. This has been interpreted as the action of a critical liquid species in reducing the cohesive strength of a stressed solid at sites of potential crack nucleation. In this way the critical transverse stress for fracture nucleation is reached at much lower stresses than is normally the case. The stresses for both fracture nucleation and fracture propagation are depressed by the same mechanism. In so doing the plastic-energy component of fracture energy is reduced to a level which is of the same order of magnitude as the surface, interfacial, or cleavage energy. Recent work2 has illustrated the influence of dispersed precipitates, cold work, and combinations of these on brittle fracture associated with plastic strains of the microyield order of magnitude. This has been rationalized in terms of the contribution of internal microstress fields to the stress magnifications at points of obstruction of active slip bands in a stressed metal. The presently reported studies on an Al-4-1/2 pct Mg alloy amplify this subject by introducing thermal-mechanical conditions which can produce strain aging. As amply demonstrated by Phillips, Swain, and borall, the tensile behavior of aluminum alloys containing magnesium reveals a yield-point elongation and successive discontinuous elongations over the whole plastic-strain range. This gives a stepped or serrated character to the stress-strain diagram. The yield-point elongation is not temperature-dependent. On the other hand, the discontinuous extensions in the plastic-strain range are gradually suppressed by lower temperatures of testing. At -78"C, only the yield-point elongation persists. The yield-point elongation itself can be suppressed by rapid quenching to room temperature from an annealing temperature of 500°C. The argument presented by Phillips et 1. and Cottre114 is that the yield-point elongation derives from surmounting at a critical stress the restraint to slip by grain boundaries which have been reinforced by appreciable magnesium-atom segregation. The serrated character of the plastic-strain range is the result of rapid strain aging during the test. This is made possible by the inevitable proximity of magnesium atoms to any dislocation line. In the Al-4-1/2 pct Mg alloy there is one magnesium atom for every twenty-two aluminum atoms and, with a coordination number of 12, a magnesium atom is on the average only about two atomic distances from any given lattice site. Rapid strain aging is therefore a reasonable expectation. A study of mercury embrittlement of the Al-4-1/2 pct Mg alloy (commercial designation 5083) provides an opportunity to relate the interplay of grain size, grain boundary restraint to slip and strain aging in the brittle-fracture process. One lot of commercial sheet material of 0.125-in. thickness was used for all of the tests. The specimen shape and test procedures used were the same as those described in a previous publication.2 A range of grain sizes between 0.0057 and 0.0125 mm was produced by various combinations of plastic prestrain and annealing. The coarsest grain was somewhat elongated in shape. In this case the measurement was taken in the direction transverse to the axis of tension as more meaningful to a brittle-fracture process. In the annealed condition, specimens wetted with mercury failed with zero permanent elongation at stresses slightly below the normal yield point, i.e., stresses at 0.05 to 0.2 pct strain. Since this occurs before yield-point elongation can begin, fracture derives from slip contained within individual grains and restrained from propagating across grain boundaries. No significant difference in wetted fracture stress was observed between specimens which had been water-quenched or furnace-cooled from the annealing temperatures. This signifies that the degree of magnesium segregation at grain boundaries

Jan 1, 1964

By J. Gurland

The effects of variations of carbon content on the constitution and properties of sintered WC-Co alloys were studied. The grain growth of tungsten carbide during sintering was measured and it was shown that it takes place mainly by solution and reprecipitation of the carbide in and from the binder at the sintering temperature. It was found that the decomposition of W3C03C by carburization during sintering is responsible for the formation of very large grains. THE properties of sintered WC-Co alloys are critically dependent upon their final composition and structure. Slight changes of cobalt and carbon contents and small variations of grain size result in marked changes of mechanical properties and performance of products. Previous investigators have studied the microstructure as a function of composition' and have dealt with the influence of cobalt upon properties.' The present work is concerned with the effect of carbon content upon constitution, microstructure, and grain growth during sintering, as well as upon the physical properties of sintered compacts. Phase Boundaries at the Sintering Temperature The WC-Co section through the ternary diagram W-Co-C has been studied by Wyman and Kelley,' Takeda,V andford and Trent," and Rautala and Norton." Two phases, namely WC and a cobalt-rich solid solution (P), appear in the sintered structure if the carbon composition corresponds very nearly to the theoretical carbon content of WC (6.12 pct C). But small deviations from the ideal carbon content will bring about the occurrence of either graphite or the double carbide W,Co3C (7) . The 7 phase was long believed to be metastable, this conclusion being based mainly on the work of Takeda. More recent studies have shown that it is a stable phase of the ternary system,"5 but the actual phase boundaries have not been established and there has been some discussion as to whether or not the 7 phase occurs at some stage of sintering in the fully carburized alloys." In view of this uncertainty it was thought advisable to undertake an investigation of the phases present during the sintering of WC-Co alloys. Commercially available tungsten, cobalt, and carbon powders were used in the present study. A typical analysis of impurities in a sintered compact is reported in Table I. The desired carbon compositions were attained by varying the amount of carbon added to the tungsten during carburization and controlling the composition during sintering by packing the compacts into beds of mixed alundum-carbon powders of suitably selected ratios. The alloys were sintered in a hydrogen tube furnace at 1400°C, then brought to equilibrium at the temperature under investigation and quenched in water. The high temperature phases were identified by metallographic and X-ray diffraction techniques. The samples were etched with a 10 pct solution of alkaline potassium ferricyanide. The phase boundaries, established by metallo-graphic examination, are shown in Fig. 1, which is a vertical section through the ternary diagram at 16 pct Co. The temperatures of the invariant planes, at 1298" and 1357°C were established by Rautala and Norton. The vertical section shows that the three-phase field, WC + 7 + L, extends into the two-phase field, WC + L, but does not include the stoichiometric composition of WC. In practice this means that the 7

Jan 1, 1955

By J. W. Furness

THE utilization and collection of waste materials have gone on for centuries, and have become a habit of the human race. The degree to which the salvaging of waste plays a part in a nation's industry depends largely on the availability of raw materials within the political confines of the country itself, or its ability to purchase such material from outside. When purchase is necessary careful economical use of the raw materials results. These economies, as a rule, are represented by lengthening the life of the given article as well as much re-use. For many years the steel industry of Italy and Japan has depended largely on importations of scrap, yet both are important. As long as the expenses incident to the conditioning and marketing of materials manufactured from salvaged waste are less than the cost of virgin material, the salvaged material will be re-fabricated and in many cases will compete with primary materials. One of the most obvious methods for furthering the efficient utilization of our limited mineral resources is the salvaging of mineral wastes. This method, moreover, in¬creases the available supply of a given material. If the price depends on a balance of supply and demand and the recovery from wastes enlarges. the supply, there can be no question but that it influences the sales price of primary.

Jan 1, 1931

By R. H. Richman, II Conard G. P.

AS part of a study of deformation twinning in bcc crystals, solid solutions of beryllium in iron have been found to twin profusely when strained slowly at room temperature. This note reports some crystal-lographic aspects of the operative mechanical twin modes in a quenched Fe-5 wt pct Be alloy. After melting twice under a partial pressure of helium, the alloy was homogenized, cut into pieces 7 to 10 mm on an edge, solution treated at 1130°C,1 and quenched. Debye-Scherrer patterns confirmed

Jan 1, 1963

Aamot, Olav Crone, Research Engr., Norsk Elektrokemisk Kongensgt, 18, Oslo, Norway ?29 Abbott, Clarence E., V.P., Charge of Raw Materials, Tenn. Coal, Iron & R. R. Co., 1242 Brown-Marx Bldg., Birmingham, Ala. '04 Abbott, Louis Benjamin, Chief Engr., Consolidation Coal Co., Watson Bldg., Fairmont, W. Va. '15 Abel, Raymond L., Asst. Prof., Dept. of Pet. Refin., Univ. of Pittsburgh Pittsburgh, Pa. '28 Abel, Walter D., Cons. Engr 364 S. Cloverdale Ave., Los Angeles, Calif. '32 Abele, Louis T 1457 Euclid Ave., Zanesville, Ohio. '31 Abell, Leo M Sullivan Concentrator, Chapman Camp, B. C., Canada. '31 Aborn, Robert H., Asst. Met., Research Lab., U. S. Steel Corp., Lincoln Highway, Kearny, N. J. '19 Abraham, W. E. V., East India United Service Club, 16 St. James' Sq., London, S. W. 1, England. '28

Jan 1, 1936

By H. M. Stewart, R. A. Grange

MANY steel parts may crack if quenched directly into a bath near room temperature, but not if quenched at a temperature just above the range where martensite forms and then allowed to cool slowly to room temperature. This latter procedure, which is the basis for such modern hardening techniques as "martempering " and "isothermal quenching," may entail some sacrifice in depth of hardening but very little, if any, in intensity of hardening. In planning such treatments, it is necessary to know the upper limit of the martensite range, and often desirable to know the proportion of martensite that would form on cooling to any lower temperature; furthermore, the tendency of a particular steel to crack when quenched is unquestionably associated with the temperature range of martensite formation, and consequently knowledge of this range aids in selecting the optimum composition for a given application. Certain puzzling phenomena associated with the properties of quenched and tempered steel may be at least partly clarified as the manner in which martensite forms is more fully under- stood. Information on the temperature range of martensite formation, particularly with respect to how much martensite results from quenching to a given temperature, is lacking for most commercial types of carbon and low-alloy steel. These considerations led us to study martensite formation in 14 carbon and low-alloy steels. The resultant data may be directly used in the following ways: (I) for selecting the lowest quenching temperature at which no martensite will form; (2) for selecting the highest quenching temperature at which virtually dl marten- site will form, thereby avoiding quenching to an unnecessarily lower temperature with attendant danger of cracking; and (3) in producing a mixture of tempered marten- site and bainite, which in high-carbon steels has been found to possess somewhat better ductility than tempered martensite, yet does not require the full transformation time necessary for a completely bainitic (austempered) structure. PART I. OBSERVATIONS OF MARTEN- SITE FORMATION IN FOURTEEN CARBON AND LOW-ALLOY STEELS Transformation of austenite to pearlite or bainite can be conveniently studied by observing the change that occurs over a period of time at constant temperature; such studies are the basis of the isothermal transformation diagram (S-curve). This isothermal technique is not applicable to martensite formation, which occurs within a time interval too small to measure, at least by any ordinary means. For all practical purposes, therefore, martensite may be regarded as forming only during cooling and not during a period of time at constant temperature. As austenite is cooled below

Jan 1, 1946

NEW MEMBERS The following list comprises the names of those persons who became members during the period Mar. 1 to 15, 1914: Members ADAMS, JOHN H., Cons. Engr First National Bank Bldg., Birmingham, Ala. ALEXANDER, WILLIAM H., Miner 80 Maiden Lane, New York, N. Y. AUSTIN, EDGAR TAYLOR, Asst. Smelter Supt., Mond Nickel Co., Ltd., Coniston, Ont., Can. BAKER, DANIEL, JR., Asst. Treas., Standard Lime & Stone Co. 524 Equitable Bldg., Baltimore, Md. BALL, MAX WAITE, Geologist U. S. Geological Survey, Washington, D. C. BARREN, HARRY B., Supt. Blast Furnaces, Inland Steel Co., Indiana Harbor, Ind. BAUMANN, HENRY N., JR., Amalgamator 365 Lynn St., Seattle, Wash. BLACK,, THOMAS B., Min. Engr Care Vulture Mines Co., Wickenburg, Ariz. BRADT, HARLAN H 429 West 111th_ St, New York, N. Y.

Jan 4, 1914

By P. G. Shewmon, W. M. Robertson

The derivative of the surface tension with orientation, ??/??, for copper has been measured over the entire unit triangle. This derivative or torque term was determined from the variation of the dihedral angles at the intersection of twin boundaries and free surfaces. High-temperature anneals in graphite with a hydrogen atmosphere gave torque terms of 0.097 at (111), 0.066 at (100), and 0.0257 at (110). A variation from -36oto +23oC in the dew Point of the H2 had no effect on these values, nor did a change from 99.98 to 99.999 pct Pure copper. The removal of graphite from the system decreased ??/?? slightly. Considering the surface near a low-index plane to be smooth except for occasional steps, the free-energy increment per cm of step is calculated, and it is shown that the observed variation of ??/?? is consistent with a random distribution of steps and an interaction energy between steps. Integration of ??/?? gave the relative values of y at (100), (110), and (111) as comPared to ymax: (Y111/Ymax) =0.974, (Y110/Ymax) =0.996, (y100/Ymax) = 0.983. The ratio of the surface tension of coherent twin boundaries to the surface tension of the free surface was found to be (yT/ys) = 0.027 * 0.011. In a crystalline solid the surface tension y (surface free energy per unit area) depends on the orientation of the surface relative to the crystallographic axes of the crystal. Measurements of this variation of y with surface orientation have been reported for metals only within the last few years. Consider the grain boundary groove shown in Fig. 1. Here the three surfaces are all normal to the plane of the paper, and each has a different surface tension, y1, y2, and y3. If the system is at equilibrium, the total surface free energy must remain unchanged for a slight vertical displacement of the intersection (points A, B, and C are kept fixed). As shown by Herring,' the following equation is obtained:

Jan 1, 1962

By James Douglas

In discussing the waste upon which hinges, or is supposed to hinge, so largely the preservation of our national resources, the conclusions reached would be more reliable if actual experience were consulted, and fewer deductions were drawn from general statements, which are often the product of the imagination. It cannot be questioned that the value of by-products has .not been sufficiently appreciated by us, and that our tardiness in recovering the useful ingredients of the escaping gas of our coke-ovens is one of the most glaring instances of shortcoming in that direction. And yet even for that sin there is some palliation in the immature condition of affiliated industries. I presume that it is admitted, without argument, that, except under very exceptional conditions, all the elements cannot be recovered from most of the ores or natural products which we treat. While it is a shame that the by-products from our coke-ovens should be dissipated, Edward W. Parker's report to the U. S. Geological Survey for 19061 supplies a fairly good excuse in justification of this appalling waste. He says (pp. 773 to 774.): " What has been already commented on in previous reports about the slowness of manufacturers to change from the better known but wasteful beehive practice to the by-product recovery method of coke manufacture is particularly emphasized in the statistics presented in this chapter. For it would appear from the table following that the construction of by-product ovens had about come to a standstill, especially when the records for the preceding five years are taken into consideration. At the close of 1901, when there were only 1,165 by-product ovens completed in the United States, there were 1,533 in course of construction, 498 of which were completed during the following year. At the close of 1902, 1,346 retort ovens were building, 293 of which were added to the completed plants in 1903. At the close of 1903, 1,335 new ovens were building and 954 of these

Jan 1, 1910

By C. F. Cockrell, K. K. Humphreys, H. E. Shajer

It is quite conceivable that the question of using coal or an alternate fuel in the future by large industrial consumers may be decided on the basis of possible profitable utilization of flyash. Accordingly, the Coal Research Bureau at West Virginia University has been attempting to develop new uses for this waste material. This effort has resulted in the development of a process for producing flyash-based face brick and other structural materials which generally exceed published specifications for competitive clay-based materials. These structural materials, containing up to 97% waste coal ash, can be produced from flyash derived from most coals without regard to the physical or chemical properties of the coal ash. Preliminary production cost estimates indicate that face brick can be manufactured at a rate of 9000 brick per hr or more with a resultant gross profit of over $24.00 per thousand brick. Plant payout time for a plant of this size would be only about 1.2 years assuming a market price of approximately $55.00 per thousand, a well established figure for comparable clay brick. With flyash production expected to more than double in the next 15 years, there is an increasing need for a practical and Profitable method for the utilization of large tonnages of this material (see Table I listing total flyash production of utilities in each state of the U.S.). Present industrial and governmental physical and chemical restrictions, particularly for use as a lightweight filler or pozzolanic material, have limited the use of flyash considerably. For those ashes which have met the required standards, utilization is not always assured because of lack of promotion and poor public acceptance. Less than 6% of the total flyash production in the U.S. was sold in 1962. The remainder was dumped in disposal areas at costs as high as $2.42 per ton.' It is quite conceivable that in the near future the question of using coal or an alternate fuel by large industrial consumers may be decided on the basis of the possible utilization of flyash. To help insure future coal demands, the Coal Research Bureau at

Jan 1, 1968

By Kefton H. Teague

Attempts to locate domestic supplies of sillimanite have been unsuccessful until recently. This paper describes recent discoveries of sil-limonite-bearing schists in the Southeastern States, with emphasis on geology of the deposits, mineral composition, origin, and reserves. Statements concerning possible methods of mining, milling, and utilization of sillimanite are given. Results from refractory tests on a laboratory scale are summarized. SINCE 1917, when synthetic mullite was first used in spark plug porcelains, there has been a continued search for natural sillimanite. During the recent war this search was intensified, not only for sillimanite but also for any materials which could be used satisfactorily as a substitute for the imported kyanite from India. The Indian massive kya-nite does not decrepitate during calcination as does our domestic bladed kyanite, thus a coarse grog can be obtained from it. Some of the most promising domestic materials suited for high temperatures are limited in quantity. Massive topaz from Chesterfield County, S. C., showed promise of possessing desirable refractory properties; but the action of combined fluorine, liberated during calcination, upon equipment and surroundings, as well as a limited supply of ore and the presence of impurities discouraged its use. Residual lumps and boulders of massive kyanite, similar to the material imported from India, occur in Georgia. This material, like the massive topaz, is of limited quantity. Andalusite from California and dumortierite from Nevada are satisfactory high-temperature refractory materials. Their uses have been restricted to specialized products since the location and character of the deposits are such that large production is impractical. Sillimanite, like kyanite and andalusite, has the theoretical chemical composition of Al2SiO5. It has a hardness of 6 to 7; vitreous, silky to subadamantine luster; specific gravity of 3.2 to 3.3; and is gray to bluish gray in color. Under the binocular microscope, the crystals are transparent. The mineral may occur as dense, fibrous mats (fibrolite) composed of fibrous, sometimes radiating hair-like crystals in schist which are associated with igneous intrusions. Deposits of this type have widespread distribution, but none discovered to date appears to have commercial possibilities. Sillimanite also occurs as bundles of crystals disseminated in biotite schist, as noted in the Hart-Elbert-Madison County, Ga., area and in some of the South Carolina and North Carolina deposits. This type of material has been called prismatic sillimanite by the U. S. Bureau of Mines. Deposits of this variety appear to offer commercial possibilities. When heated above 1650°C, sillimanite expands about 6.5 pct and is converted into a mixture of mullite (3Al2O3 . SiO2) and vitreous silica. This is a stable mixture which has a specific gravity of about 3.15. General Geology: Sillimanite (fibrolite) is a mineral common to the pre-Cambrian metasedi-ments of the Southeast. It occurs throughout the crystalline schists which lie between the Fall Line on the southeast and the established Paleozoic rocks on the northwest (fig. 1). In addition to the meta-sediments, this area contains pre-Cambrian igneous

Jan 1, 1951

By Kefton H. Teague

Attempts to locate domestic supplies of sillimanite have been unsuccessful until recently. This paper describes recent discoveries of sil-limonite-bearing schists in the Southeastern States, with emphasis on geology of the deposits, mineral composition, origin, and reserves. Statements concerning possible methods of mining, milling, and utilization of sillimanite are given. Results from refractory tests on a laboratory scale are summarized. SINCE 1917, when synthetic mullite was first used in spark plug porcelains, there has been a continued search for natural sillimanite. During the recent war this search was intensified, not only for sillimanite but also for any materials which could be used satisfactorily as a substitute for the imported kyanite from India. The Indian massive kya-nite does not decrepitate during calcination as does our domestic bladed kyanite, thus a coarse grog can be obtained from it. Some of the most promising domestic materials suited for high temperatures are limited in quantity. Massive topaz from Chesterfield County, S. C., showed promise of possessing desirable refractory properties; but the action of combined fluorine, liberated during calcination, upon equipment and surroundings, as well as a limited supply of ore and the presence of impurities discouraged its use. Residual lumps and boulders of massive kyanite, similar to the material imported from India, occur in Georgia. This material, like the massive topaz, is of limited quantity. Andalusite from California and dumortierite from Nevada are satisfactory high-temperature refractory materials. Their uses have been restricted to specialized products since the location and character of the deposits are such that large production is impractical. Sillimanite, like kyanite and andalusite, has the theoretical chemical composition of Al2SiO5. It has a hardness of 6 to 7; vitreous, silky to subadamantine luster; specific gravity of 3.2 to 3.3; and is gray to bluish gray in color. Under the binocular microscope, the crystals are transparent. The mineral may occur as dense, fibrous mats (fibrolite) composed of fibrous, sometimes radiating hair-like crystals in schist which are associated with igneous intrusions. Deposits of this type have widespread distribution, but none discovered to date appears to have commercial possibilities. Sillimanite also occurs as bundles of crystals disseminated in biotite schist, as noted in the Hart-Elbert-Madison County, Ga., area and in some of the South Carolina and North Carolina deposits. This type of material has been called prismatic sillimanite by the U. S. Bureau of Mines. Deposits of this variety appear to offer commercial possibilities. When heated above 1650°C, sillimanite expands about 6.5 pct and is converted into a mixture of mullite (3Al2O3 . SiO2) and vitreous silica. This is a stable mixture which has a specific gravity of about 3.15. General Geology: Sillimanite (fibrolite) is a mineral common to the pre-Cambrian metasedi-ments of the Southeast. It occurs throughout the crystalline schists which lie between the Fall Line on the southeast and the established Paleozoic rocks on the northwest (fig. 1). In addition to the meta-sediments, this area contains pre-Cambrian igneous

Jan 1, 1951

By L. Ibagos S., T. Balberyszski

The volumetric flow rate and the initial concentration of the copper sulfate solution influence the rate of reaction and, hence, the precipitation efficiency in a continuous launder cementation system. Using a model of such a system it was found that the precipitation efficiency is related to the two process parameters by the approximate expression [ log [1-n] = -[0.072 co 2.91 e – 0.511c o Q 1.15 ] N Q] where c is the initial concentration, Q, is the volumetric flow rate and N is the number of launders in the system. This expression agrees with an equation developed for the rate of the cementation process if it is assumed that the exponential factor represents the change in the surface area with concentration and the exponents 2.91-and 1.15 relate the hydrodynamic conditions and the surface concentration to co and Q. The experimental results are used to determine the values of a Precipitation Coefficient for any volumentric flow rate and initial concentration of solution. Knowing the Precipitation Coefficient, the total volume of launders that will result in a given precipitation efficiency can be calculated. It is established that maximum precipitation efficiencies are obtained for initial concentrations between 6.0 and 7.0 gpl and volumetric flow rates of approximately 350 m3 /hr Good agreement between calculated and actual launder volumes is obtained for a number of industrial operations for which a comparison is made.

Jan 1, 1973

By R. J. Wasilewski

The variation of elastic modulus with terrzperature between -150° and 600°C has been investigated. Compounds close to equiatomic cornposition exhibit very low modulus values and very high damping near room temperature. The modulus rises steeply with both decreasing and increasing temperature. The modulus minimum and the high damping are believed to be connected with a martensitic transformation of TiNi. In bulk material this transition takes place slightly above room temperature quite rapidly and reversibly, with a hysteresis of some 30°C, depending on the Ti:Ni ratio. Oxygen impurity affects the reaction time. THE inter metallic compound TiNi has been reported to exist in an ordered CsCl (B2) structure,l-6 the homogeneity range varying rather markedly with temperature.7 Some investigators reported this compound to decompose peritectoidally to Ti2Ni and TiNi, between 650° and 800°C,3 or below,',g the latter workers also suggesting the decomposition to be strain-sensitive. Purdy and Parr were the first to report a structural transformation to a new, possibly hexagonal, structure at 36°C,7 a temperature indubitably too low to allow the significant amount of diffusion necessary for a peritectoid reaction. Mechanical-property investigations of compositions close to TiNi just above room temperature have qualitatively shown remarkable anomalies, particularly with respect to clamping,' and to a "memory" effect, that is, plastically deformed material returning to its original shape on being heated through the "decomposition" temperature.9 The original explanation of this effect—based on the apparent experimental observation of Ti2Ni or TiNi, formation in the material subjected to tensile or compressive stresses, respectivelp—does not appear plausible. It appeared more probable that the change involved may be a martensitic, diffusionless structural transformation, similar to those observed in other B2 structures such as 0 brass,'' AuCd,ll and AuZn.12 The existence of such transformation has been established recently,', although the symmetry of the low-temperature structure is not yet known. The present paper describes the elastic modulus and damping behavior of polycrystalline TiNi in both structures. EXPERIMENTAL METHOD 1) Specimens. All the specimens to be investigated were prepared from premelted electrolytic nickel and iodide titanium by nonconsumable arc melting and casting in a water-cooled copper mold. The cast billets were canned in mild steel, extruded, and swaged to approximately 0.375 in. diam. The cans were then removed by pickling or machining. Preliminary material balance checks indicated no significant weight losses on melting (less than 5 mg on a 50-g button); hence nominal compositions have been used throughout. In agreement with previously reported observations7 no single-phase material was obtained at—or close to—Ti 1.00 Ni1.00 a small amount of finely divided second phase always being present. It was found that most of the oxygen impurity was associated with this minor phase, which was identified as oxygen-bearing Ti2Ni—possibly Ti,Ni,O. The amount of this phase—at any given Ti:Ni composi-

Jan 1, 1965

(The following list contains the names of those members of the Institute of whose connection with military service we have only recently become acquainted; it also includes the names of a few who have recently been promoted or transferred, indicated by a *. A complete list was published in the Year Book, issued as a supplement of the Bulletin for March, 1918.) ALLEN, Roy H., Capt., Air Service, Bureau of Aircraft Production, Washington, D. C. *AMIDON, CLAUDE E., Chemical Warfare Section', Astoria, L. I. *ARCHBALD, HUGH, 311th Infantry, 78th Division, American E. F. ASKIN, THOMAS B. H., Radio Station, Cavite, P. I. *AYER, FRANK A., Lieut., Commanding Officer, -270th Aero Squadron, American E. F. BARBA, W. P., Lieut. Colonel, Ordnance, U. S. A., Washington, D. C. *BARRETT, LESLIE P., 1st Lieut., 5th Field Artillery, American E. F. BLICKENSDERFER, F. C., 1st Lieut., N. A., Ordnance Dept., Edgewood Arsenal, Edgewood, Md. *BROOKS, FLOYD R.., Lieut., Canadian Engineers, Seaford, England. BROWN, GEORGE M., Co. G, 1st Replacement Regiment, Washington Barracks, D. C. *BRUNEL, LOUIS J., Lieut., 5th Field Artillery, Brigade Headquarters, American E. F. *BRUNTON, D. W., Cons. Engr., Naval Consulting Board, Washington, D. C.

Jan 11, 1918

By Leroy Gardner

EVERY reader of this paper is well aware of the fact that the prolonged inhalation of large amounts of free silica dust results in fibrosis of the lungs, and that other inorganic dusts, except those of asbestos and the mineral poisons, are thought to be relatively harmless. But probably few have had opportunity to visualize the effects of silica, asbestos and other minerals upon living tissues. The ideal demonstration would be based upon sections of lungs from human beings that had inhaled com-parable concentrations of different dusts for a unit period of time. Such material is generally difficult to obtain and in some instances is of ques-tionable value because the subject has been exposed to more than one kind of dust. A demonstration could be prepared from the lungs of animals. However, so many months or even years are required to com-plete the exposure to each kind of dust that enough material has not been accumulated. For a general survey of the action of different types of dust, I am therefore compelled to use the tissues of animals that have been injected with suspensions of dust particles. The injection method offers certain advantages. The quantity, the particle size and the state of dispersion can be controlled with sufficient accuracy so that the tissue responses to different minerals can be accu-rately compared. The method insures contact between the tissues and the mineral particles; protective mechanisms, which may prevent the inhalation of certain types of foreign body, never come into play. If the pathway of injection be one that minimizes nonspecific injury, the tissue responses may simulate those produced by inhalation but they develop somewhat more rapidly. It should always be remembered that injection methods merely demonstrate the capacity of various kinds of minerals to provoke reaction in the tissues; whether the same substances are inhaled from atmospheric suspension and accumulate in the lungs in dangerous quantities can be demonstrated only by inhalation.

Jan 1, 1938

By John E. Riddell

This review is based on a questionnaire sent out in 1959 to 24 Canadian exploration companies, known to be active in the mineral exploration field, concerning their practice in the use of applied geo-chemical techniques in Precambrian terrains. Of the companies questioned, 21 returned completed questionnaires and of these, 15 companies stated that they had some experience in this type of work. Of the companies who stated that they had no experience in geochemical prospecting in glaciated Precambrian areas it is interesting to note that only three have reported that they do not use applied geochemistry at all. The others have reported that they make use of applied geochemistry in New Brunswick and in the Cordillera in areas of light glaciation. Their opinion is that it is a useful aid when accompanied by other techniques in evaluating mineralized areas. GEOCHEMICAL SURVEYS Table I reviews the type of geochemical surveys used by these companies, and the following points of interest should be noted.

Jan 11, 1960

By Edward J. Way

+1KLEINFONTEIN GROUP CENTRAL ADMlNISTRATION, BENONI, TRANSVAAL, S. AFRICA. The cost and the speed of sinking a shaft are factors of so great importance in operating a mine, that the data given in Table I., herewith published, will be of interest and value to all engaged in practical mining; and for this reason the data are communicated for permanent and accessible record in our Transactions. The figures 'of cost cover the period from January 1, 1903, to May 31, 1903, during which time the total depth sunk was 858 ft. So far as I know, the cost of sinking per foot (£13,15s., 11.04d.) of a shaft of the dimensions 21 ft. by 6 ft. in hard rock, is the cheapest yet on record; and the speed of 213.5 ft. per month, which was attained during May, 1903, is also the best record for speed in sinking in rock so hard as that of this shaft. During the period from January 1 to May 31, 1903, there were 144 rounds worked, involving 4,032 holes, of a total depth of 28,963 ft. 2.4 in., which is equivalent to an average depth of 7 ft. 2.2 in. per hole bored. These data are of added interest from the fact that the work was done practically by native labor.

Jan 1, 1905