Search Documents

By Cyril Stanley Smith

The method of thermal analysis, so important in the development of metallographie science, has of recent years been falling into disuse owing to the development of other physical methods which give result's easier of interpretation and which can be used for the study of either equilibrium or transitional conditions because they do not require a continuously changing temperature. Nevertheless thermal analysis remains useful in the study of reactions that take place rapidly, and the simplicity of the experimental technique and the general availability of the apparatus involved are point's in its favor. Theoretically, thermal analysis is capable of giving specific and latent hat measurements and therefore should permit the study of reactions on a more fundamental basis than any other method. It is, however,difficult or impossible to obtain quantitative heat measurements from cooling curves obtained in the usual way. Even if the furnace containing the sample is cooled or heated at a linear rate, or if a gradient furnaec is employed to maintain a constant rate over a large range of temperature, the heat flow from or to the specimen depends on its previous history, for the difference of temperature between the specimen and its surroundings varies. The emissivity of the specimen surface, moreover, is unlikely to be constant. The able mathematical analysis by Russrll,1 although it prevent,s misinterpretat,ion of data, has an effect rather the reverse of that intended, and leaves the reader doubtful of the possibility of ever obtaining quantitative results from thermal curves. Nothing can be done to apply thermal analysis t'o the study of equilibrium conditions of reactions that arc not completed at rates of temperature change above about 1° C;. per minute, and this unfortunatetly excludes most solid transformations in alloys.† For the determination of liquidus

Jan 1, 1940

By Cyril Stanley Smith

The method of thermal analysis, so important in the development of metallographie science, has of recent years been falling into disuse owing to the development of other physical methods which give result's easier of interpretation and which can be used for the study of either equilibrium or transitional conditions because they do not require a continuously changing temperature. Nevertheless thermal analysis remains useful in the study of reactions that take place rapidly, and the simplicity of the experimental technique and the general availability of the apparatus involved are point's in its favor. Theoretically, thermal analysis is capable of giving specific and latent hat measurements and therefore should permit the study of reactions on a more fundamental basis than any other method. It is, however,difficult or impossible to obtain quantitative heat measurements from cooling curves obtained in the usual way. Even if the furnace containing the sample is cooled or heated at a linear rate, or if a gradient furnaec is employed to maintain a constant rate over a large range of temperature, the heat flow from or to the specimen depends on its previous history, for the difference of temperature between the specimen and its surroundings varies. The emissivity of the specimen surface, moreover, is unlikely to be constant. The able mathematical analysis by Russrll,1 although it prevent,s misinterpretat,ion of data, has an effect rather the reverse of that intended, and leaves the reader doubtful of the possibility of ever obtaining quantitative results from thermal curves. Nothing can be done to apply thermal analysis t'o the study of equilibrium conditions of reactions that arc not completed at rates of temperature change above about 1° C;. per minute, and this unfortunatetly excludes most solid transformations in alloys.† For the determination of liquidus

Jan 1, 1940

By Roberto Fernandez

Want of knowledge on the part of experts from abroad respecting the amalgamation-system, known as the Mexican or patio process, has been the cause in this country of trouble to many foreign mining companies. This process has not been looked upon by their managers as a satisfactory method of treating silver-ores, and they prefer to employ others, which, although more modern, and often more profitable in other countries, have not proved to be so under the exceptional conditions of this country, where labor is cheap and paid in silver, while fuel is very dear. The cause of this error of judgment is probably the inexact information which has been furnished by several authors respecting the economical results of the patio process. This treatment is not suitable for silver-ores of every kind. Simple sulphides of silver are best adapted to it, and, next to these, the combinations of complex sulphides, viz., pyrargyrite, polybasite, stephanite, proustite, etc. Chlorides, bromides and iodides of silver are considered rebellious ; argentiferous galena, blende, bournonite, as also argentiferous arsenical pyrites of iron and copper, are absolutelg unsuited to this treatment. Experience has proved that high-grade ores do not give as satisfactory results as those of mediurn grades, as, for instance, carrying from 1 to 2 kilos of silver per metrical ton. The patio process, as actually practiced in this district, comprises the following operations: 1. The ore is crushed in a dry state in a roller-mill, reducing it to pea-size, from which uniform samples, and, in consequence, correct assays, can be obtained. 2. It is then thrown into the arrastra, and pulverized with water, so fine that it will pass through an 80-mesh screen.

Jan 1, 1900

By Harrison R. Cooper

The key to concentrator automation is practical means for obtaining continuous assay data from concentrator streams. The technique most successfully used is x-ray fluorescence analysis. The practical reality of on-stream x-ray analysis has been achieved through effort over the past twenty years, marked by an occasional breakthrough, but more typically a step-by-step development to which many individuals and organizations have contributed. The net result of this progress is the present capability to install on-stream x-ray analyzer systems on a turn-key basis. It is now possible to provide all components of an x-ray analysis system as a completely engineered unit which can be put into immediate use, minimizing needs for specialized application knowledge to benefit from continuous assaying in process control. The economic factors which influence the choice of system and limitations of the x-ray fluorescence technique for slurry analysis are reviewed.

Jan 1, 1976

By Y. H. Liu, G. W. Powell

Thin foils made from the gold-rich region of- short (0.15 mm)Au-Ag diffusion couples annealed at 880°C for 1 hr were examined in ax electron microscope and the structures were compared with that of pure gold subjected to identical heat treatments. The couples underwent Plastic deformation (bending) during the diffusional anneal. The foils prepared from the diffusion zone have a higher dislocation density and incidence of subboundaries than pure gold. The plastic bending of the couple can be interpreted in terms of the climb of edge dislocations, which are pavallel to the bend axis, along the direction of diffusion. THE interaction of lattice defects during interdiffu-sion between two metals has been considered by several investigators. In particular, da Silva and Mehl,1 Barnes,' and Bardeen and Herring3 have proposed models based on interactions between point and line defects to account for the Kirkendall effect (marker movement). Each of these models is based on dislocation climb, which can either add or remove lattice planes, induced by an under- or supersaturation of vacancies. A theoretical treatment of the nucleation and growth of voids by the condensation of vacancies has been presented by Seitz.4 Stresses can arise in a binary diffusion couple as a result of the vacancy flux and the gradient in the lattice parameter. rinkmman' has investigated the effects of diffusion-induced stresses on void formation; the results of his analysis suggest that voids can form and grow under the influence of these stresses in the absence of an excess vacancy concentration. The relationships between vacancy supersaturation and diffusion-induced stresses and void formation have been elucidated also by Balluffi and seigle6 who concluded that the stress generated by a vacancy supersaturation aids the growth of voids. Experimental evidence which indirectly shows that stresses are produced by chemical diffusion has been obtained by several researchers.2,7-9 This evidence consists in part of the observation by light microscopy of the formation of subgrains, a process characteristic of the high-temperature deformation of some metals during creep.'0 More striking, however, is the plastic bending of short (0.2 mm) Cu-Ni couples observed by Barnes2 and of boron-doped silicon crystals reported by Queisser.9 Diffusion-induced dislocations in iron and silicon have been investigated by Ainslie et a1.11and Schwutte and Queisser,12 respectively, the former using transmission electron microscopy and the latter an X-ray transmission technique. Matthews and Crawford13 observed the formation of boundaries by the climb of interfacial misfit dislocations in thin, vapor-deposited Au-Pd couples diffused in situ in an electron microscope. In order to obtain additional information on the phenomena associated with defect interaction and diffusion-induced stresses in binary couples, an electron transmission study of foils prepared from the diffusion zone of short Au-Ag couples was undertaken. The initial objective was to investigate the processes occurring at various points of the diffusion zone. Subsequent research demonstrated that foils could be prepared only from the gold-rich region of the diffusion zone using the technique described herein. EXPERIMENTAL PROCEDURE Preparation and Annealing of the Diffusion Couples. The couples were made from annealed, high-purity (99.999 pct). polycrvstalline gold and silver sheets (0.075 mm thick). Shall (0.075 by 5 by 17 mm) elec-tropolished coupons of gold and silver were pressure-bonded by heating the two metals in a graphite device to 770°C and holding at this temperature for approximately 30 min. The quality of the bond was ascertained by metallographic examination at 150 times. Each couple subsequently was annealed at 880°C for 1hr; under these conditions, the extreme portions of the

Jan 1, 1968

By John A. Church

IT is a well-known fact that under similar conditions a ton of pig iron can be made from any ore with less fuel when charcoal is used than when coke or anthracite is employed for heating. The cause of this superiority is entirely undiscovered, and no explanation has yet been offered which has won even temporary acceptance. Such as they are the hypotheses heretofore presented are of two general kinds, and they come from those two divisions of the working force which are so often antagonistic in all professions, the scientific and the practical men. The theory of the scientific men is drawn from the chemical reactions which are known to go on in the furnace, and it is well expressed in a recent paper by Prof. Akerman, of the Stockholm (Sweden) School of Mines. It makes the superiority of charcoal as a fuel in the blast furnace to depend upon its quick and thorough reduction of carbonic acid. This property belongs to charcoal in virtue of its porous structure. Its cells have a diameter of only one twenty-four hundredth of an inch, and one grain of charcoal has been computed to have a surface of two and four-tenths square feet. According to the theory in question, carbonic acid is formed by the first impact of the air upon the fuel; but in charcoal furnaces the acid is immediately reduced to oxide by taking the necessary amount of carbon into combination, and the gas reaches its highest reducing power even in the near vicinity of the tuyeres. Coke, being harder, does not produce so strong a reducing gas in that part of. the furnace. Carbonic acid is formed as in the case of charcoal, and remains longer before its reduction to oxide is completed. Anthracite is the

Jan 1, 1879

By W. W. Stephens, W. J. Kroll, H. P. Holmes

THE only two methods for producing commercial quantities of malleable zirconium, up to now, have been using magnesium reduction of the anhydrous chloride under a neutral gas, and using purification of raw zirconium by the iodide dissociation method on a hot filament. The purity of the metal obtained by the latter process is about the same as that resulting from the chloride reduction, with the exception of the oxygen content, which may be about 0.05 pct lower in the iodide metal. Even traces of oxygen have a strong hardening effect on zirconium. Since, in the iodide process, the impurities, Si, Al, Fe, Ni, and Mg in the raw zirconium used, are carried over, it would appear uneconomical to use this method of refining solely to eliminate the traces of oxygen, unless very soft metal is desired. One important step to improve the iodide method, namely, dissociating pure iodide made from carbide and recycling the iodine, which would change this refining process into a method for extracting zirconium from the ore, has not yet been made. The Bureau of Mines, by using the chloride reduction, wanted to produce quantities of a reasonably pure and malleable metal at low cost for large-scale industrial use. This aim has been achieved, and a pilot plant permitting production of 600 lb of malleable zirconium per week will be described (fig. 1). Briefly, the Bureau of Mines process consists of reducing purified gaseous anhydrous zirconium chloride with fused magnesium under a noble-gas atmosphere. The reaction product, magnesium chloride, and any excess magnesium metal present are removed from the sponge zirconium in the next step by fusion and evaporation in a good vacuum at about 925°C. In this process, care is taken to keep air out of contact with the hot metal, which otherwise would contaminate the product with oxygen and nitrogen. Both these impurities embrittle zirconium even when present in an amount as low as 0.1 pct. A number of previous reports1-3 describe the method and the various improvements that finally led to a workable process. The major steps made were the production of large quantities of carbide, which is the raw material for producing the chloride, its chlorination with reasonable efficiencies, and the elimination of iron trichloride contained in the raw chloride, as well as that of the zirconium oxide which is always present in this product. The physical nature of the anhydrous chloride, which sublimes at 331°C at atmospheric pressure and melts at 420°C under a pressure of 25 atm, made it necessary to provide a special safety device on the purification and reduction vessels in the form of a lead-alloy seal, permitting escape of excess gases if pressure tended to build up. The main difficulties encountered in the reduction and in the following step, salt separation in a vacuum at elevated temperature, were caused by the material from which the reaction pot was constructed—iron. This metal reacts with zirconium at about 940°C with formation of a eutectic. The last step, salt separation by evaporation of the magnesium and magnesium chloride in a vacuum, is quite unconventional and has not been used before on such a scale. It is only due to the improved construction of high-vacuum pumps, especially oil-diffusion pumps, that such a method could be used. The various steps of the Bureau of Mines process, as described in the general outline above, may be summarized as follows: (1) production of the carbide, (2) chlorination of the carbide, (3) purification of the raw chloride, (4) reduction of the pure chloride with fused magnesium, (5) separation of excess magnesium and magnesium chloride in vacuum at elevated temperature, and (6) melting of the sponge obtained. Production of Carbide The arc furnace, described in a previous report,' was improved both to reduce the graphite consumption caused by the burning of the bottom plates and to concentrate the heat in order to obtain better power efficiency. This was achieved by providing the bottom with graphite plates entirely embedded in refractory bricks, the contact with the current being made with three water-cooled copper plugs. Figs. 2 and 3 show the arrangement. The crucible, made

Jan 1, 1951

By John B. Cook

Most of today's open pits take the form of conical-shaped excavations in the relatively flat or undulating terrain surrounding them. Ore is usually hauled uphill from the pit bottom by truck, rail, or skip to crushing, beneficiation, railroad loading, and stockpiling facilities near the edge of the pit. There are, however, a few orebodies whose locations in mountainous terrain causes special problems that generate different technical solutions. LAMCO's 10.5 million metric tons per year high-grade iron mine in the Nimba Range in tropical Liberia is probably one of the most extreme of these exceptions (Fig. 1). At Nimba there is a 2,000-ft difference in elevation between the upper- most levels of the orebodies and the start of the railroad below at the foot of the mountain. Haulage to the crusher is usually downhill at grades of up to 12% dictated by the topography of the rugged terrain. Ore is transported from the crusher down the mountainside by a conveyor sys- tem 10,096 ft long, whose average grade is 18%. The belt is braked by asynchronous generators, feeding power into the local network. The original crusher must be relocated at a lower elevation outside the final pit limit to allow that part of the mountain on which it now stands to be excavated. HISTORY The LAMCO Joint Venture is owned 75% by the Liberian-American- Swedish Minerals Co. (LAMCO) and 25% by Bethlehem Steel Corp. LAMCO is comprised of a 50% interest by the Liberian Government and 50% interest by Liberian Iron Ore Ltd (Fig. 2). This joint venture was launched to develop the high-grade iron ore deposits of the Nimba Range.

Jan 1, 1969

Discussion of the paper of A. P. WATT, presented at the St. Louis meeting, October, 1917, and printed in Bulletin No. 130, October, 1917, pp. 1476 to 1563. THE CHAIRMAN (0. M. _BILHARZ, Miami, Okla.).-Mr. Watt's reference to sorting or hand-picking of the ore in the lead district, which is being introduced at Mine La Motte, is especially interesting. I believe, from my former experience in the district, that hand-picking should be practised to some extent by all the companies in the Lead Belt. I know that a great many thousand tons containing only very small amounts of lead are passed through the mills, which, of course, is not to the advantage of milling machinery. That procedure may be Warranted at times of high prices, but I think that hand-picking should ordinarily be adopted to some extent: ERNEST GAYFORD, Salt Lake City, Utah.-On page 1525, speaking of the settling of slime previous to treatment either on slime tables or by flotation, Mr. Watt states: "The settling area allowed per ton of dry slime varies from 11 to 16 sq. ft.-an average for the district would be about 13 sq. ft. of settling area per ton of dry slime. This figure applies when the, discharge contains 20 per cent. solids." Mr. Ramsey, of the Dorr company, is here and I would like to ask him whether a settling area of 13 sq. ft. per ton of dry slime per 24 hr. is not considerably above the average area of Dorr settling tanks, and whether 20 per cent. solids is not above the general dilution for that' capacity? I should also like to know what is the general average on slimes of that character. E. R. RAMSEY, Denver, Colo.-An allowance of 13 sq. ft. per ton does seem rather large. I am not familiar with the settling characteristics of the dolomitic gangue, but as an average over the country, I should say that 6 or 7 sq. ft. would be nearer correct for discharge at that consistency. L. A. DELANO, Bowie Terre, Mo.-We have had an opportunity to try our tanks at the highest capacity, and-find that by thickening the slime to 30 per cent. solids we average 12 sq. ft. per ton of dry slime. ERNEST GAYFORD.-DO you find any definite ratio between the thickness of the discharge and the settling capacity of the tank? Do you consider that the tank has a larger capacity if the discharge is 3 to 1 than if it is 50 per cent. solids? L. A. DELANO.-I think it has greater capacity with the thinner discharge. It depends a good deal on the density of feed to the tanks; in our case the feed contains 2.5 per cent. solids.

Jan 1, 1918

By Kenneth Cottingham

The number of wells completed in Ohio during I940 was about 20 per cent more than during the preceding year, the comparative totals being 1020 and 1228. Of the 1940 completions, 327 were oil wells, 491 gas wells, and 410 dry. The completions for the past five years, divided into oil wells, gas wells, and dry holes, are shown in Table 2. Wells drilled deeper and input wells in water-flood areas are not included in the tabulation. The annual production of oil has decreased steadily in Ohio from the maximum of 23,941,000 bbl. produced in 1896. Table 3 shows the quantities of oil produced in the last five years. In 1940, the total was 3,052,000 bbl., produced by about 25,500 wells. The number of wells and the approximate quantities by grades are shown in Table I. Table i ,—Tabulation by Grade Grade 1 2 Barrels __________________________________________________________________________________________ Pennsylvania ............. . 1,198,000 Lima.................... . 325,000 Corning................... 3,730 1,159,000 Lodi...................... T,040 350,000 Cleveland................. 30 1:1,000 Total................... 25,500 3,052,000 The prices paid for Ohio crude oil in 1940, together with dates of changes in posting, are shown in Table 4. The production of natural gas in 0hio has declined from a maximum of 79,510,032 M cu. ft. in I9I5 S to 36,469,000 M cu. ft. in 1939, the most recent year for which a figure is available. Consumption reached its peak in Ohio in the year 1916, when it was 169,480,01r M cu. ft., declining to 114,720,ooo M CU. ft. in 1939. The produc-tion and consumption of natural gas in Ohio for the past five years are shown in Table 5. TAble 2.—Completions in Ohio during Past Five Years Numbs of Wells Drilled during Year YearI, ] Oil Gas Dry Total 1936............. 263 570 324 1,157 1937............. 317 503 45I 1,271 1938............. 189 433 288 gro 1939............. I70 501 349 1,020 19391940............. 327 491 410 1,228 Total.......... 1,266 2,498 1,822 5,586 Table 6 shows the number of oil wells and the number of gas wells completed by sands during 1940, with the average initial production per well for each sand. Table 7 shows the total number of wells drilled—oil, gas and dry—by sands. Development during 1940 Szth-Trenton.—For several years, considerahle interest has been shown in a horizon lying some 500 to 700 ft. below the top of the Trenton, known to the driller in western Ohio as the "green sand," and in eastern Ohio as the St. Peter. In 1939, ten 'lgreen sand" tests were drilled, all in western Ohio and all dry- In 19401 eight wells were drilled to this horizon, one of which was a small oil well (one barrel) in Men county- Of the remaining seven—all of which were dry-—one in Franklin County, in central Ohio, was drilled to a depth of 2903 ft. .Another was in Medina

Jan 1, 1941

By Kenneth Cottingham

The number of wells completed in Ohio during I940 was about 20 per cent more than during the preceding year, the comparative totals being 1020 and 1228. Of the 1940 completions, 327 were oil wells, 491 gas wells, and 410 dry. The completions for the past five years, divided into oil wells, gas wells, and dry holes, are shown in Table 2. Wells drilled deeper and input wells in water-flood areas are not included in the tabulation. The annual production of oil has decreased steadily in Ohio from the maximum of 23,941,000 bbl. produced in 1896. Table 3 shows the quantities of oil produced in the last five years. In 1940, the total was 3,052,000 bbl., produced by about 25,500 wells. The number of wells and the approximate quantities by grades are shown in Table I. Table i ,—Tabulation by Grade Grade 1 2 Barrels __________________________________________________________________________________________ Pennsylvania ............. . 1,198,000 Lima.................... . 325,000 Corning................... 3,730 1,159,000 Lodi...................... T,040 350,000 Cleveland................. 30 1:1,000 Total................... 25,500 3,052,000 The prices paid for Ohio crude oil in 1940, together with dates of changes in posting, are shown in Table 4. The production of natural gas in 0hio has declined from a maximum of 79,510,032 M cu. ft. in I9I5 S to 36,469,000 M cu. ft. in 1939, the most recent year for which a figure is available. Consumption reached its peak in Ohio in the year 1916, when it was 169,480,01r M cu. ft., declining to 114,720,ooo M CU. ft. in 1939. The produc-tion and consumption of natural gas in Ohio for the past five years are shown in Table 5. TAble 2.—Completions in Ohio during Past Five Years Numbs of Wells Drilled during Year YearI, ] Oil Gas Dry Total 1936............. 263 570 324 1,157 1937............. 317 503 45I 1,271 1938............. 189 433 288 gro 1939............. I70 501 349 1,020 19391940............. 327 491 410 1,228 Total.......... 1,266 2,498 1,822 5,586 Table 6 shows the number of oil wells and the number of gas wells completed by sands during 1940, with the average initial production per well for each sand. Table 7 shows the total number of wells drilled—oil, gas and dry—by sands. Development during 1940 Szth-Trenton.—For several years, considerahle interest has been shown in a horizon lying some 500 to 700 ft. below the top of the Trenton, known to the driller in western Ohio as the "green sand," and in eastern Ohio as the St. Peter. In 1939, ten 'lgreen sand" tests were drilled, all in western Ohio and all dry- In 19401 eight wells were drilled to this horizon, one of which was a small oil well (one barrel) in Men county- Of the remaining seven—all of which were dry-—one in Franklin County, in central Ohio, was drilled to a depth of 2903 ft. .Another was in Medina

Jan 1, 1941

By Richard P. Rothwell

The anthracite coals of Pennsylvania are all mined from large veins. A seam less than four feet. in thickness is generally considered as unworkable, those from which most of the coal now comes being from 8 'to 30 feet thick. The system of mining employed is, almost without exception, that known as " chamber and pillar work;" that is, the coal is taken out of chambers of from 18 to 30 feet in width, and pillars of from 12 to 20 feet are left between these to support the roof. In general, the entire thickness of the seam, even

By Y. C. Liu, H. Margolin

Investigation of martensite habit plane in water-quenched Ti-Mn alloys was carried out in the range of manganese contents between 4.35 and 5.25 pct. On the basis of 22 measurements, the poles were observed to fall into two groups, indicating the existence of two habit planes. The Miller indices of the poles close to these two groups were found to be <334>ß and <344>ß. TITANIUM has an allotropic transformation at 882.1° ± 0.5C1 by which the high temperature ß (body-centered cubic) phase changes to a (hexagonal close-packed) phase. It is well known, as in the case of low carbon steel, that the unalloyed high temperature ß phase cannot be retained no matter how rapid the cooling rate. However, the addition of alloying elements usually lowers the transformation temperature continuously and stabilizes the ß phase to a temperature much lower than the allotropic transformation temperature in pure titanium. A typical example of this behavior is found with manganese-alloying of titanium. Fig. 1 shows the titanium-rich Ti-Mn equilibrium diagram as established by Battelle Memorial Institute.&apos; The addition of manganese lowers the ß transus line and the eutectoid reaction takes place at 550°C, the eutectoid composition being 20 wt pct Mn. However, upon quenching to room temperature from the ß field, the ß phase can be completely retained with much less manganese, see Fig. 2. If the composition is less than that required to stabilize the ß phase completely, a plate-like structure, similar to that of martensite in other alloy systems, appears as shown in Fig. 3. Much lower alloying content merely intensifies the amounts of these transformed structures, as shown in Fig. 4. This paper presents the results of an investigation of the habit plane of these martensitic structures in Ti-Mn alloys. Experimental Procedure Investigation of the pole of a given platelet was made using the two-surface method of analysis." In order that a given martensite trace on two surfaces be readily recognized both at low and high magnifications, it is desirable that only a small amount of martensite be present. From a review of the data obtained at Battelle Memorial Institute4 on quench hardening in Ti-Mn alloys and the results of Duwez" on transformation in Ti-MO alloys, it was decided that the most appropriate Ti-Mn composition for this study would be about 6 pct Mn. A group of alloys containing from 3 to 10 pct Mn was made to bracket this composition. The choice of the 6 pct alloy was apparently proper, since it was later learned that approximately 5.5 to 6 pct Mn is required to stabilize the ß phase on water quenching.

Jan 1, 1954

By George Rice

THE A.I.M.E. Ground Movement and Subsidence Committee, pro-posed in 1920, held its first technical meeting in February 1923, under the able chairmanship of Mr. H. G. Moulton. The following list of papers and discussions, indicating the scope of the problems and relation to various conditions and method of mining, were given at that meeting by the distinguished mining engineers: J. Parke Channing, on Subsidence at Miami, Arizona; Howard N. Eavenson, on Mining an Upper Bitu-minous Seam after a Lower Seam Has Been Extracted; J. J. Rutledge, on Subsidence in Two Oklahoma Coal Mines; Benjamin F. Tillson, on Caving Cracks at the Franklin Mine, New Jersey; Dr. F. W. McNair, on the Dome Theory; William Kelly, on disadvantageous effects in Mining and Back-filling Working Upward a Steep-Fitching Iron-ore Bed; Eli T. Conner, on the good results of Back-Filling by Hydraulic Means in Preventing Destructive Subsidence in the Anthracite District; Thomas H. Claggett, on the merit of Systematic Pillar Drawing in Preventing Cracks in an Upper Seam; Henry H. Otto, successful results in the anthracite district in Mining Lower Seams before Upper Seams; Douglas Bunting, on Leading Factors Incident to Successful Mining of an Overlying Seam; Edwin Ludlow, on there being "less damage to buildings when there was complete removal of coal with complete packing than when room and pillar is used without extracting the pillars"; Edward O&apos;Toole on "bumps" in eastern Kentucky mines, which he thought were the result of geologic stresses: H. A. Buehler, on Upheaval of Surface in an Illinois Case in Advance of the Face; and R. Dawson Hall, on The Mechanics of Subsidence from Mining. The author of this paper discussed various kinds of problems of ground movement and subsidence in both metal mining and coal mining; the production of great landslides by workings near an outcrop, as at Turtle Mountain, Alberta, Canada; and general

Jan 1, 1939

Ore deposits of commercial grade are local concentrations of great rarity when considered in relation to the area of unmineralized land surfaces, and they must therefore be considered as the products of exceptional and complex conditions. The data collected from a great number of individual deposits are sufficient to permit certain broad generalizations in regard to the conditions favorable to ore deposition which even numerous exceptions do not invalidate. The broadest general relation of ore deposits is with intrusive rocks, and while there are notable exceptions, the great majority of ore deposits have a visible or closely inferred connection with intrusive rock masses. Conditions that permit the dissipation of the ore-bearing vehicles do not permit the concentration of metals in deposits; the prime factor to consider in this connection is that structural conditions must be such as tend to concentrate and not to dissipate the ore-bearing solutions. The disadvantage of extrusive rocks is at once apparent; any metals the magma may have contained are dissipated at the surface and are lost; with the exception of tiny vugs and cracks in quickly cooled flows, no concentrations of metals are known in extrusive rocks, and the lack of confinement and quick cooling apparently do not permit extrusives to exert mineralizing effect upon the rocks with which they come in contact. The close mineralogical similarity between extrusives and intrusives, and the great difference in mineralizing power is a proof of the ease with which magmas part with their metallic content, and of the mobility of the ore-bearing vehicles in comparison with the parent magma.

Jan 1, 1932

By H. A. Schwartz, W. Kenneth Bock

In this paper it is shown that when the tensile strength of a given steel in various states of heat-treatment is plotted against its elongation, a straight line results. The equation of this straight line can be computed with considerable accuracy from its chemical composition. The appropriate equations are given. The logarithm of the slope of the tensile-strength locus is shown to be proportional to the cumulative effect of the total alloy addition and the vosition of the line to be directly proportional to the cumulative effect of the alloy content. It is further pointed out that heat-treatment is more effective than composition in determining yield ratio. The latter enters mainly by its effect on hardenability, which is briefly discussed. Reduction of area and Brinell number are given some incidental attention. The data are applicable only to steels that have been normalized and/or quenched. The steels, if normalized, may or may not have been tempered. If quenched they must have been tempered at or above 4oo°C. (75o°F.). Introduction Cast steels vary in composition and frequently are used in various states of heat-treatment. It is obviously important to be able to predict the compositions that might accompany specific engineering properties by suitable selection of heat-treatments. For cast steels, which are of necessity produced heat by heat in accordance with the particular requirements of the castings to be poured, there has been, happily, much less tendency to standardization than for rolled products, whose destination is not necessarily known when particular ingots are made or rolled. It is of distinct advantage to the steel foundry-men to be able to make steel of given properties, using alloys that can be recovered from scrap, or most conveniently or cheaply bought, rather than a particular formula adopted in the interest of standardization. The heat-treatment appropriate to securing a given result in a given steel is well known to be closely related to composition. For example, molybdenum steels are not much softened by tempering except at rather high temperatures. Highly alloyed steels are "air-hardening," and on cooling in air behave like carbon steels that have been quenched. With these matters, we do not concern ourselves in this paper, although we recognize their importance. The entire picture evidently will be very complex and can be brought within accurate understanding only if our knowledge of test results can be coordinated in terms of general principles.

Jan 1, 1944

By H. A. Schwartz, W. Kenneth Bock

In this paper it is shown that when the tensile strength of a given steel in various states of heat-treatment is plotted against its elongation, a straight line results. The equation of this straight line can be computed with considerable accuracy from its chemical composition. The appropriate equations are given. The logarithm of the slope of the tensile-strength locus is shown to be proportional to the cumulative effect of the total alloy addition and the vosition of the line to be directly proportional to the cumulative effect of the alloy content. It is further pointed out that heat-treatment is more effective than composition in determining yield ratio. The latter enters mainly by its effect on hardenability, which is briefly discussed. Reduction of area and Brinell number are given some incidental attention. The data are applicable only to steels that have been normalized and/or quenched. The steels, if normalized, may or may not have been tempered. If quenched they must have been tempered at or above 4oo°C. (75o°F.). Introduction Cast steels vary in composition and frequently are used in various states of heat-treatment. It is obviously important to be able to predict the compositions that might accompany specific engineering properties by suitable selection of heat-treatments. For cast steels, which are of necessity produced heat by heat in accordance with the particular requirements of the castings to be poured, there has been, happily, much less tendency to standardization than for rolled products, whose destination is not necessarily known when particular ingots are made or rolled. It is of distinct advantage to the steel foundry-men to be able to make steel of given properties, using alloys that can be recovered from scrap, or most conveniently or cheaply bought, rather than a particular formula adopted in the interest of standardization. The heat-treatment appropriate to securing a given result in a given steel is well known to be closely related to composition. For example, molybdenum steels are not much softened by tempering except at rather high temperatures. Highly alloyed steels are "air-hardening," and on cooling in air behave like carbon steels that have been quenched. With these matters, we do not concern ourselves in this paper, although we recognize their importance. The entire picture evidently will be very complex and can be brought within accurate understanding only if our knowledge of test results can be coordinated in terms of general principles.

Jan 1, 1944

By D. H. Newland

New York has a small but not insignificant place in the oil and natural gas industries of the United States. It has had a continuous record as an oil producer since 1872, with an aggregate yield of about 104,000,000 bbl. The reported output for 1935 was 4,237,000 bbl., a gain of more than 10 per cent for the year and a total that has been exceeded only in the early period of flush production half a century ago. The industry has been steadily building up since 1920 with the successful practice of the water drive, which has given a new lease of life to pools that had been practically drained of oil recoverable by pumping. An additional output of 2000 bbl. or more per acre is being procured by this method. Altogether the fields in New York State cover about 55,000 acres. Their limits are well defined and it is unlikely that they will be extended in the future, although there is some prospect of finding additional supplies by deeper drilling. The oil from New York is all classed as Pennsylvania grade, for which the recent price has been about $2.50 a barrel. It is refined at Olean, Wellsville and Bolivar, in the oil district, and partly in Pennsylvania refineries. Exploration for natural gas, outside of the established districts, was considerable during the year. Altogether 59 wells were drilled, distributed over 13 counties, of which 33 were listed as producers and 26 were dry. At the close of the year, 13 wells were in process of drilling. The 33 producing wells had a combined estimated flow of 278 million cubic feet per day. The best results were obtained from exploration in Allegany County, where out of eight wells drilled to the Oriskany sandstone five were successful and showed a combined open-flow capacity of 107 million cubic feet. The Oriskany sandstone was encountered at a depth of 4500 to 4900 ft. In Steuben County, next east of Allegany County, two out of seven wells to the Oriskany proved productive, and one of these, in the town of Greenwood, on the Watkins structure, was probably the largest that has so far been opened in the state, with a reported yield of 35 million a day. In the central part of New York interest was awakened by the activity shown in exploring for gas in the Trenton limestone, in Camden, Florence and Rome townships, Oneida

Jan 1, 1936

By D. H. Newland

New York has a small but not insignificant place in the oil and natural gas industries of the United States. It has had a continuous record as an oil producer since 1872, with an aggregate yield of about 104,000,000 bbl. The reported output for 1935 was 4,237,000 bbl., a gain of more than 10 per cent for the year and a total that has been exceeded only in the early period of flush production half a century ago. The industry has been steadily building up since 1920 with the successful practice of the water drive, which has given a new lease of life to pools that had been practically drained of oil recoverable by pumping. An additional output of 2000 bbl. or more per acre is being procured by this method. Altogether the fields in New York State cover about 55,000 acres. Their limits are well defined and it is unlikely that they will be extended in the future, although there is some prospect of finding additional supplies by deeper drilling. The oil from New York is all classed as Pennsylvania grade, for which the recent price has been about $2.50 a barrel. It is refined at Olean, Wellsville and Bolivar, in the oil district, and partly in Pennsylvania refineries. Exploration for natural gas, outside of the established districts, was considerable during the year. Altogether 59 wells were drilled, distributed over 13 counties, of which 33 were listed as producers and 26 were dry. At the close of the year, 13 wells were in process of drilling. The 33 producing wells had a combined estimated flow of 278 million cubic feet per day. The best results were obtained from exploration in Allegany County, where out of eight wells drilled to the Oriskany sandstone five were successful and showed a combined open-flow capacity of 107 million cubic feet. The Oriskany sandstone was encountered at a depth of 4500 to 4900 ft. In Steuben County, next east of Allegany County, two out of seven wells to the Oriskany proved productive, and one of these, in the town of Greenwood, on the Watkins structure, was probably the largest that has so far been opened in the state, with a reported yield of 35 million a day. In the central part of New York interest was awakened by the activity shown in exploring for gas in the Trenton limestone, in Camden, Florence and Rome townships, Oneida

Jan 1, 1936

By Leo Ranney

ANY years ago a prospector came to a Nevada town and built himself a shack. Day after day he searched the hills for gold -but he found none. He closed his shack and hurried north, where a strike had been made. Next he tried to trap the flour gold that floats down the Snake River. He panned the black sands along the Oregon coast. He ranged over the mountains and up the gulches of far-off Alaska. At last, broken in health, six years ago he came back to his old home in Nevada. There his shack still stood-nobody wanted it. One day he started a garden in the rocky soil that he owned. His spade turned up a chunk of quartz, and in that quartz were stringers of gold. He had found a rich gold vein, running right under his own house. You gas producers who have hurried to Oklahoma, Louisiana, East Texas, South Texas, West Texas, even to California to drill wildcat holes a mile or two miles deep-why not, like the old gold prospector, have a look in your own back yard? Some of your coal seams contain 20,000,000 cu. ft. of natural gas per acre.

Jan 1, 1943