Search Documents

By Lucien Eaton

THE use of filling in mines is less common in the United States than it is in Europe, where in some places it is required by law. In most cases the filling is placed by hand, and the material used for this purpose is the waste from development and that sorted from the ore in the stopes. When these sources provide an insufficient supply, additional rock must be quarried on surface or mined underground, or some other material :st be used. In different parts of the world sand, clay, gravel, culm, nulated slag, mill tailings, and even ashes, have been used as filling material in place of or in conjunction with rock. Of all the materials used for filling the best is probably clean sand. Gravel, finely crushed rock, granulated slag and coarse mill tailings are almost as good, and the methods used for placing and confining sand will apply equally well to any of these. The advantages of sand are its comparatively slight compressibility and the ease, economy and convenience with which it may be placed. On account of the voids, which necessarily occur in fills made of coarse waste, such fills will compress 10 to 25 per cent before they develop their full strength, whereas clean sand seldom compresses more than 5 per cent. Sand is especially desirable when practically complete filling is required, and sand derived from mill tailings, especially when not thoroughly cleaned, has been remarkably effective in sealing off and extinguishing mine fires. When natural sand is available on surface, or when it can be obtained from the mill tailings or tailings dump, the cost of using this material for fill will probably be considerably less than that of rock. In this paper it is not proposed to discuss all methods of filling, butt to describe some of the methods used for placing sand fill and to make a brief comparison of their merits.

Jan 1, 1932

By David Schroeder, John Chipman

Jan 1, 1964

By Louis Moyd

In the preparation of illustrations to accompany reports of investigations concerning particle shapes of various natural and manufactured materials proposed for use as fine aggretates in concrete structures, it was found that stereoscopic views of such materials presented the information much more effectively than the usual two-dimensional photographs. With the whole-hearted cooperation of the Photographic Section, a technique was developed in the petrographic laboratory of the Concrete Research Division, U.S. Corps of Engineers, at Clinton, Miss., for simple and rapid preparation of paired stereoscopic photographs and micrographs. The method requires only equipment which is usually part of the general stock of any laboratory, and it is adaptable for all purposes in which three-dimensional views would be found superior to ordinary photographs.

Jan 1, 1949

By B. A. Rogers

IN addition to the usual methods of manufacturing steel, a number of special processes have been the subject of considerable experimentation-and use in manufacturing practice. A number of these methods have been of a type in which a rapid refining action has been secured through the intimate mixture of fluid slag with fluid metal. The persistence with which more rapid methods are sought is indicated by the current interest in the Aston' method for producing wrought iron and in the Perrin2 process for dephosphorizing and deoxidizing steel. In the Perrin process, in particular, the mixing action is extremely vigorous and the reactions proceed with surprising speed.

Jan 1, 1936

By J. B. Fletcher

The Miami mine first started operations in 1910. For convenience, the history of the orebody can be divided into the following categories (Fig. 1): 1) 1910 to 1925: 24.4 million tons of high grade ore, mined by top slicing, sublevel caving, etc. 2) 1926 to 1954: 102 million tons of low grade ore, mined by block caving.

Jan 1, 1961

By D. R. Cook

This paper is a case history of an exploration venture for base metals, begun by the Rocky Mountain District of Bear Creek Mining Company in 1952 and completed in 1954. The project was based on the idea of W. S. Burbank, U. S. Geological Survey, that commercial deposits of base metals might occur in Paleozoic sediments beneath hydrothermally altered volcanic rocks in the Southern Bonanza mining district, Colorado. Here, an area of andesitic rocks, four square miles in extent, has been argillized, pyritized, chloritized and silicified. Geological, geophysical and geochemical studies were followed by the diamond drilling of three holes totalling 6,220 feet. Further alteration ang geochemical studies were made on the cores from these holes. A brief review of the alteration and geologic mapping, colored aerial photograph interpretation, geochemical soil and rock sampling, magnetic, gravity and radio-metric surveys are presented together with some conclusions regarding this work. This paper is a case history of an exploration venture for base metals, begun by the Rocky Mountain District of Bear Creek Mining Company in 1952 and completed in 1954. Important contributions were made to the project by personnel of the Rocky Mountain District and the Geophysics Division. Individual acknowledgements to these people are made at the end of the paper. BASIS FOR THE PROJECT The project was based on the idea of W. S. Burbank (1947, p. 444) that commercial deposits of base metals might occur in Paleozoic sediments beneath hydrothermally altered volcanic rocks in the Southern Bonanza mining district, Colorado. Paleozoic sedimentary rocks, including the favorable Leadville limestone, are exposed three miles south of the altered area, and reason exists to believe that they might underlie it within a reasonable depth. Alteration of pre-mineral volcanic rocks has been used successfully as a guide to concealed orebodies in the Main Tintic and East Tin tic mining districts, Utah (Bill-ingsley, 1933, p. 120-122; Lovering et al, 1949; Howd, 1957, p. 124-134; Cook, 1957, p. 73) and could be a useful guide here. GENERAL GEOLOGY AND STRUCTURE The Northern and Southern Bonanza mining districts are northwest of the San Luis Valley in southern Colorado, just within the northeastern edge of the San Juan volcanic province. The districts are1ocated on the southern extension of the Sawatch uplift, a prorninent northwest-trending structural high. The highly productive mining camp. of Leadville, Gilman and Aspen are on the northeastern and northwestern flanks of this uplift where Paleozoic limestones have

Jan 1, 1961

By E. C. Olsen

This paper describes the unusual hazardous conditions encountered in mining thick, inclined coal beds under heavy cover in Carbon County, Utah. This description includes heavy roof conditions, sloughing ribs, steep pitches, and severe bouncing experience. Emphasis is placed on the top bench system of mining and development in the top half of a 16-ft seam, under the roof rock, which is bolted, and the recovery of the bottom coal on retreat; success of bolted roof and ribs; and shuttle car haulage on pitches up to 25%. The use of protective cages for operators of face equipment, the guarding of belt conveyor systems to prevent injury associated with deliberate entry, and the positive lockout of electrical equipment is described and illustrated. Most coal mining areas of the Western United States are characterized either by thick beds, steep pitches or heavy cover. Individually, each of these may present inherent safety hazards that in- fluence mining. When all are met at one location, the combined effect is to make the safe operation of the mining property a challenge to management. These combined conditions are met in the coal mines of the Columbia-Geneva Steel Div. of the United States Steel Corp., in southeastern Utah. This coal bed measures up to 16 ft in thickness, the pitch is as much as 25% and mining is under a cover approaching 3000 ft. The Sunnyside coal bed is found in the Book Cliff Mountains, a great escarpment extending from west of Castle Gate, Utah, some 180 miles to Grand Junction, Colo. West of Green River, Utah, the Book Cliffs swing sharply to the north because of the domelike uplift of the San Rafael Swell to the southwest. It is in this northerly extension of the Book Cliffs that the Sunnyside coal in the Blackhawk Formation of the Mesa Verde Group, Upper Cretaceous Age is found. The strata are transected by numerous faults with from a few inches to as much as a hundred feet of displacement. All of these faults have had some effect on the mining operation, either in roof control or, in the case of major faulting, the pattern of mine development. MINING PRACTICES Mining has generally been confined to the Lower Sunnyside Seam which measures from 7 to 16 ft in

Jan 1, 1963

By John R. Eckel

A Iaboratory drilling rig has been devised and placed in operation which permits the application of hydrostatic, terrastatic, and formation pore pressures to a rock sample for drilling under controlled conditions. Calibrated rests of this equipment in-dicate qualitative agreerment with field results on the effect of weight on bit, rotary speed, and rate of circ~~lation on drilling rate. Tests under pressure, using water and air as the drilling fluids, indicate that when drilling saturated limestone samples, a pressure differential between hydrostatic and formation pressure is the only pressure which affects drilling rate. A differential in either direction causes a reduction in rate, but the same diflerential from the wellbore into the formation causes the greater reduction. Also, in lime.stone, air favorably affected drilling rote only when compared to water at high hydrostatic pressurre, all other conditions remaining constant. Large increases in drilling rate with air could be obtained in the laboratory only while drilling a shale, which offered a limited permeability to nitrogen and which could be drilled with a differential from the formation into the wellbore. In general, the magnitude of the changes due to the pressure effect were small compared to changes in drilling rate obtainable by changing either bit weight or rotary speed. INTRODUCTION In the course of Humble's drilling research program, the desirability of investigating several factors which lend themselves to laboratory rather than field study became obvious. Principal reasons for this are the expense involved in field studies and the difficulty of exercising the required degree of control. Of primary importance are investigations of the effect of fluid pressure on rock rate, the effect of pressure on rock drillability, and a study of the fundamental mechanics of rock failure and chip generation. Several years ago some work in the laboratory on the effect of mud properties on drilling rate was re- ported to the API', but the completion of this work and the investigation of the other variables affecting drilling rate required equipment somewhat more elaborate than that used on these earlier tests. This equipment has been assembled to form Humble's Drilling Engineering laboratory. To date only the effect of pressure on rock drillability while using water and air has been investigated, and this work is not yet complete. Facilities are available to investigate the effect of fluid properties on rate of penetration, and information is being assembled on a current basis on the mechanics of drilling. The sequence of presentation in this progress report is somewhat different from that in which the data were obtained since the order of ex-

By AIME AIME

TWO days of solid discussion, with barely time out for meals, characterized the Tulsa meeting of the Petroleum Division. It was preeminently an earnest gathering devoted to technical matters. Sessions were held in the Crystal room of the Mayo Hotel with luncheon served each day in the back of the same room so that talk of methods, while slightly less formal, extended right through the lunch hour. Thursday evening the Committee did provide a little relaxation in an informal dinner at the Tulsa Club where, after a brief musical program and an amusing skit by the local Herman the Great, brief addresses in non-technical vein were made by President Farish and Vice-president Rice of the Humble Company, Henry L. Doherty of Cities Service, Secretary. Bain of the Institute, and others. The presence of leading executives of a number of the oil companies at the dinner and the sessions, and the cordial approval they expressed of the work of the Division were especially gratifying. The total registration was 215 with 100 at the dinner and 70-to 80 lunching together each day.

Jan 1, 1930

By E. S. Moore

Although nickel was in use in alloys long before the Christian era, the metal was not discovered until 1751, when Cronstedt recognized it in niccolite from Sweden. The Chinese apparently used a nickel alloy, known as "pahfong" thousands of years ago and Persian coins dating farther back than 200 B.C. consist of a copper-nickel alloy similar to some of those now in use in coins. The pure metal was first prepared about 1775 and the metal was refined for commercial purposes some years later. The nickel industry did not attain much prominence until the ores in New Caledonia were discovered. Exports of ore from that country began in 1875 and since that date there has been an ever-increasing world output of nickel and a great expansion in the uses of the metal except during short periods of commercial and industrial depression. Previous to 1875, for a number of years, Norway was the chief producer, although the metal was mined also in Sweden, Finland, Italy, Germany, Austria, France, China, the United States and other countries. With the discovery of nickel deposits in the Sudbury district, Ontario, a new factor was introduced into the nickel industry and Sudbury has since become the overwhelmingly dominant feature in the world's nickel markets. Although nickel was first discovered in Canada as early as 1848 near the north shore of Lake Huron and nickel-copper sulfides were found in 1856 by surveyors working close to the present location of the important rnine at Creighton, in the Sudbury field, it was not until 1883 that any importance was attached to this field. In that year copper sulfide attracted attention where the main line of the Canadian Pacific railroad was being projected across Canada to the Pacific coast. Mining began near this discovery in 1889 but in the meantime operations had begun in 1886 in other parts of the field and by 1890 about 100,000 tons of ore had been raised. In the Sudbury field, as in Norway and at the old Lancaster Gap mine in Pennsylvania, the ore was first mined for its copper content and difficully in the refining of the copper led to the discovery of the important proportions of nickel in the ore. No. 3 property of the International Nickel Co., now known as the Frood, the greatest deposit in the

Jan 1, 1932

By David Cole

THE appearance of the Wilfley table in 1897 marked an epoch in the art of concentration of ores. The table has merited and received an almost unprecedented measure of public approval, lasting through its whole patent life. It has been very little improved in itself, or improved upon by competitors. The new machines bidding for popular favor have been of the Wilfley family, but without ability to do markedly better work than the parent m:-chine, or to (to more work except by the use of superimposed decks, the latter having obvious disadvantages. FIG. 1.-The- Butchart RIFFLE System. During the past three years there has been developed at Morenci a new type or arrangement of riffles applicable to the Wilfley type of concentrating table which corrects many of the objectionable features or limitations of the older system and obviates most of the difficulties encountered with it, particularly when handling ores having a low ratio of concentration. The new type is known as the Butchart1 riffle system, and its general arrangement is shown in Figs. 1 and 2.

Jan 2, 1915

By H. H. Dreissen, F. J. Fontein

The operating principle of the classifying cyclone has been described often but some special aspects of the cyclone receive further clarification here. In addition, several uses of the classifiers are summarized and made clear by means of practical examples. In coal and ore washeries, the washing cyclone is widely used for the separation by specific gravity of sizes up to about 12 mm. This application has lately been extended to the separation by specific gravity of particles up to about 50 mm. This use makes special demands on the construction and wear resistance of the cyclone. The sieve bend, a development of the Dutch State Mines which is less well known than the hydrocy-clone, is dealt with at some length. The sieve bend is an apparatus designed for wet screening. Attention is given to the variables influencing the performance of the sieve bend. Hydrocyclones are now so widely applied that it would be difficult to find an industry not, directly or indirectly, using them or knowing how to use them since publications on this subject abound.1-3,5,9-11,13-15 However, because of the large number of variables influencing the operation of classifying cyclones, it is not entirely possible to calculate the results of this type of cyclone. Therefore, a number of lesser known variables will be discussed here along with some special applications of the classifying cyclone. FACTORS INFLUENCING CYCLONE CLASSIFICATION Shape of Particles: The shape of particles may cause a much coarser classification than the one expected, considering the sieve analysis and the cyclone dimensions chosen. This was clearly shown by feeding a mixture of spheres and disks in water into a cyclone. The spheres were 0.36 mm diam and the disks, 3 mm diam and 0.03 mm thick. These dimensions were chosen in order that the disks and spheres might have the same rates of fall under gravity. Both spheres and disks had a specific gravity of 1.05. The results obtained with these particles in a cyclone are summarized in Table I. Test No. 2 shows that the catch of spheres was

Jan 1, 1963

By Edwin Berry

THE consideration of the present value of a mine is of great importance when planning for the operation of a property,, and it is particularly so in the case of mines that have large ore reserves. At various times during the past 15 years, the writer has had occasion to make rather thorough studies of the subject, and has been greatly impressed by certain important points which these studies have brought out, points which, though they may be well known, are often lost track of in the rush to obtain low mining costs and high daily tonnage output. . It is the object of this paper to present briefly, and in a general way, some of these points, and especially those which have to do with the relationship which (1) ore reserves and plant capacity, (2) grade of ore mined, and (3) ore losses in mining, bear to the present value. Present value, sometimes called present worth or actuarial value, means the value today of the future earnings of an enterprise. Great industrial, manu-facturing or railroad enterprises, if properly handled, go on indefinitely and their value is directly dependent on their estimated annual earnings. Mines, or oil properties, on the other hand, have an earning capacity only until the ore or oil is exhausted, and their present value is dependent not only on their annual earnings but also on their life, which is the length of the period over which they can produce at a profit. A mine, or an oil property, is a "wasting asset," while an estab-lished manufacturing business is not, or should not be. In other words, the present value of a mining property. represents a sum of money on which there could be paid from operating profits a determined rate of interest, say 8 per cent., and in addition an amount which, if invested at compound interest as received, would at the end of the life of the mine pay back the present value. In his "Wealth and Income of the American People," Walter Renton Ingalls says: "The fundamental principle of mine valuation is the present worth of an annual dividend accruing during the period of years corresponding to the life of the mine."

Jan 7, 1922

By L. F. Elkins

In 1946 Littlefield, Gray and Godbold published a thorough geologic description of the West Edmond Hunton Lime reservoir, located in Central Oklahoma, and discussion of its early performance.l They stressed implications of the nature of the reservoir rock on performance to be expected with production both by natural means and by pressure maintenance with gas injection. The essence of their analysis was that presence of an extensive interconnected system of fractures and solution channels constituting about 10 percent of the total reservoir void space in otherwise very low permeability reservoir rock would result in severe channeling of naturally encroaching water or injected gas through the fractures with little or no benefit to ultimate recovery of oil. Considerations were in progress to unitize the reservoir for pressure maintenance by gas injection. Some other engineers involved in the project had considerably different opinions at the time regarding continuity of fractures and regarding effects of such fractures on performance. The field was unitized Oct. 1, 1947. Subsequently, pilot gas injection tests were conducted in four areas of the field; large scale waterflooding was conducted in two parts of the field in the Bois d'Arc or Upper Hunton; and pilot waterflooding was conducted in the Chimney Hill or Lower Hunton. Full scale water-flooding is now in progress in the Chimney Hill section where it is oil productive. The primary purpose of this paper is to divine some of the secrets of this reservoir through analysis of all aspects of its performance, with the hope that it will be of help to engineers and operators in developing and operating other low permeability fractured reservoirs. In part, this considers variance of actual performance from some widely used conventional reservoir engineering assumptions. For brevity, other aspects of unit operation and its benefits to the owners are not discussed. Oil and Gas in Place For unit participation, net pay in the Bois #Arc defined by the gross SP anomaly on electric logs totalled 2,100,000 acre-ft in the 30,000-acre reservoir. Development of West Edmond predated modem logging techniques that now would be used to determine "net" or "productive" pay. In Fig. 1 this log pick is compared with detailed core analysis and core descripfion by Littlefield et a1.l for one well identified as A on the index map in Fig. 2. Not all of the gross Bois #Arc section had oil staining, but all cores with measureable intergranular permeability were stained. (The committee selection of the Bois d'Arc SP interval also includes the Frisco section as identified from cores by Littlefield.) The Bois d'Arc is oil productive throughout the entire 600-ft monoclinal accumulation from the eastern upstructure erosional pinchout to the west-side oil-water contact. (See Littlefield et al.l and McGee and Jenkins for geologic detail.)

Jan 1, 1970

By A. E. Chute

The shortage of sulfur is not only continuing but appears to be worsening, attended by steadily rising prices. At the same time emphasis on air-pollution abatement is also increasing. These two factors, a rising market and the growth of environmental attention, have encouraged producers to carefully review all possible sulfur sources. As a result, production of sulfur from hydrogen sulfide occurring in petroleum is receiving greater attention than ever before. Until about a decade ago, the practice of recovering sulfur from hydrogen sulfide separated from gases (either found naturally or generated in desulfurization of liquid petroleum) was wide1y recognized but contributed little to total free-world sulfur production. However, during the past ten years, the production of sulfur from this source has increased so rapidly that it now accounts for a substantial portion of total production. This trend shows no signs of slackening, and current forecasts predict that recovered sulfur may become the dominant source of supply within ten years, exceeding mined sulfur production. This paper is intended to list sulfur sources and relationships, and to discuss the potential of producing sulfur from petroleum. The processing involved, in addition to product storage and transportation will also be discussed along with important economic aspects of sulfur recovered from hydrogen sulfide. For many years, most of the world's elemental sulfur has been produced from salt domes, predominantly by the Frasch process. During the past decade, however, another production source has developed so quickly that it is expected to surpass the Frasch production sources within a short time. This new source lies in the petroleum gases and liquids from which dramatically increasing quantities of elemental sulfur are being recovered. In the phraseology of the trade, the sulfur so obtained is know as "recovered sulfur," a term which does not, as one might expect, include sulfur recovered from other sources such as smelter gases. The growth rate of recovered sulfur compared to that of Frasch sulfur, total elemental sulfur, and total Free World sulfur in all forms is shown in Fig. 1 Since 1963, sulfur consumption has exceeded production,with the natural result that the price of sulfurhas continually increased. The posted price reported for f.o.b. Port Sulphur, La., has risen from as low as $18 per ton in 1962 to $32.50 per ton in mid-1967. With freight and other charges, delivered prices have of course run much higher, amounting to $45 or $46 per ton on the east and west coasts. In some cases, spot sales for as much as $60 have been reported. Although it is playing an ever-increasing role in the sulfur market, recovered sulfur was originally a by-product of the removal of hydrogen sulfide from natural and petroleum refinery gases. Today, however, it is often the most valuable product of a multi-product processing facility. Since there are two major sources of recovered sulfur—production and refining processes —natural gas is included with liquid petroleum for purposes of this discussion. Sulfur from these sources is produced in the form of gaseous hydrogen sulfide which is removed from a gas stream and converted to elemental sulfur. Gases in which hydrogen sulfide occurs naturally are natural gas and the gas produced from a high=pres-sure crude=oil or condensate field.

Jan 1, 1969

By H. D. Outmans

A method has been developed for determining the relative water wet-tability (fraction of the surface wet by water) of porous media. This method involves the adsorption of methylene blue dye from an aqueous solution onto the solid surfaces of rock contacted by the injected dye solution. Experiments on Berea snndstone cores have shown that water-wet cores adsorb a large amount of dye from solution. In oil-wet cores, however, the injected aqueous dye solution is prevented from contacting the adsorptive surfuces by a film of oil and virtually no dye is adsorbed. This method was tested by experiments on mixtures of water-wet and oil-wet sand. Using the dye adsorption method, it was possible to determine quantitatively the fraction of water-wet and oil-wet sarzd in such mixtures. The dye adsorption test is readily applied to determinitrg the relative water wettability of fresh oilfield cores. The cores are not extracted before testing. Observed values of the wettability of field cores tested to date have varied from 100 to 6 per cent water wet. INTR OD UCTIO N Recent articles1 ' have emphasized the important role that wettability plays in almost all phases of reservoir rock behavior. It has been shown that wettability has a profound effect on the interstitial water saturation, residual oil saturation, capillary pressure, relative permeability, waterflood behavior, and resistivity index of oilfield cores. A quantitative investiga- tion of the effect of wettability on these core properties is severely handicapped by the lack of a simple technique for measuring the wettability of a porous medium. If such a technique were available, it would provide investigators with a means of gaining insight into the distribution of phases within a core. A number of qualitative methods of estimating wettability are known. These include contact angle measurements, flotation tests and studies of displacement pressure: imbibition7 and relative permeability data.' Using these tests, it is usually possible to classify a core as water-wet, oil-wet, or some intermediate degree of wettability. One recently proposed method involving measurement of nuclear magnetic relaxatione offers promise of determining quantitatively the fractional wettability of cores. The equipment is rather elaborate and necessary treatment of the cores before testing probably alters the natural wettability. This latter point also applies to most of the cited qualitative methods. This paper presents a new technique for determining water wettability of cores; it is based on measurements of the dye adsorption capacity of the core. This method has the advantage of requiring relatively simple equipment and involves minimum handling of the core before testing. It is important to distinguish between the various concepts of wettability referred to in the literature. The term "wetting" is defined by Bartell as that phenomenon which occurs when a solid and liquid phase come in contact in any manner so as to form a solid-liquid interface. A preferentially water-wet solid is defined by Jennings in terms of the advancing contact angle in the solid water-oil systems. Brown and Fatt regard fractional wettability as the fraction of the total surface area that is preferentially oil-wet or water-wet. However, none of these definitions adequately describes the type wettability measured by the dye test. This calls for the introduction of a new term, "relative water wettability", which we define as the fraction of the total surface area of a core contacted by injected water. DESCRIPTION OF METHOD The ability of a porous medium (especially the clays) to adsorb large quantities of surfactants, dyes, etc., is well known. It is reasonable to assume that a substance can be adsorbed from solution onto a solid surface only if the solution contacts the surface. In this connection Shapiro" has shown by experiments on silica gel that completely dry gel will adsorb methyl red dye from a benzene solution. On the other hand, if a film of water more than several molecules thick is present on the silica gel, the adsorption capacity of the gel for the dye is drastically reduced. Thus, a study of the dye adsorption capacity of cores should give some clue as to the fluid distribution on the surface of the core. TEST OF METHOD As a qualitative check on this theory, dye adsorption tests were run on similar Berea sandstone cores (Table 1, Cores 1-5). Cores saturated initially with water and flooded with 0.01 per cent aqueous methylene blue adsorbed 0.58 mg dye/gm of core. Similar cores saturated initially with water, driven to irreducible water with oil, and then flooded with the same dye solution also adsorbed 0.58 mg dye/gm of core. Another core, treated with a 5 per cent Dri-Film solution, dried and saturated with oil (Soltrol) adsorbed no dye when the dye solution was injected. These tests confirm

By J. B. Cheatham, M. D. Biggs

This paper presents a systematic method for determining the forces on a simplified roller bit. The kinematics of an actual roller bit drilling in rock is complex; nevertheless, it is desirable to obtain an accurate analytical model.. As a preliminary study, the roller bit is represented here by a simple two-dimensional bit and the rock by a Coulomb plastic material. Results from previous work, plus additional assumptions, are incorporated into a computer program to determine the forces required to move the bit in a specified manner. Example problems are worked by use of this program. By studying similar drilling problems and by supporting laboratory work, one could eventually obtain an accurate analytical model for drilling by an actual roller bit. This could lead to the compilation of a catalog of results that, in turn, would allow selection of the optimum drill bit for any given situation. INTRODUCTION

Jan 1, 1970

By H. T. Kennedy, S. M. Avasthi

An equation developed for gaseous hydrocarbon mixtures predicts molal volumes with an average absolute deviation of 0.73 percent when applied to 264 natural gas and condensate systems including 2,043 PVT points. Another equation developed for liquid hydrocarbon mixtures predicts molal volumes with an average absolute deviation of 1.12 percent when applied to 346 crude oil systems including 1,759 PVT points. Both equations require composition of the mixture to be expressed as mole fraction of methane through heptanes-plus, hydrogen sulfide, nitrogen and carbon dioxide, together with the characteristics of the heptanes-plus fraction in addition to the temperature and pressure. The equations cover wide ranges of the variables involved, and their accuracy is considerably better than that of other available methods. The equations were differentiated to allow calculation of the coefficients of isothermal compressibility and isobaric thermal expansion. (In this paper the coefficient of isothermal com-pressibility and the coefficient of isobaric thermal expansion will be expressed as compressibility and thermal expansion coefficient, respectively.) Equations to calculate these quantities are presented. INTRODUCTION Calculations of reservoir performance for petroleum reservoirs require accurate knowledge of the volumetric behavior of hydrocarbon mixtures, both liquid and gaseous. Compressibilities are required in transient fluid flow problems, and thermal expansion coefficients are important in thermal methods of production. An accurate laboratory investigation of the PVT behavior of each reservoir fluid encountered would be costly and time consuming. For this reason various correlations for predicting fluid properties have been developed and recorded in recent literature. Correlations have been presented in the form of graphs, tables and equations. Since an increasing number of studies are being conducted with the aid of electronic computers, recent efforts have been directed toward development of correla-tions suitable for computer programming. Application of computers permits the use of more complex correlations which otherwise are not feasible. Moreover, methods for predicting reservoir performance, particularly those based on the compositional material balance, depend upon the capability of accurately expressing the molal volumes and other fluid properties as functions of pressure, temperature and composition. The coefficient of isothermal compressibility c is defined by

Jan 1, 1969

By John Chipman, Wayne L. Worrell

Using recent thermodynamic data for the carbides and oxides of tantalum, columbium, and vanadium, the stable solid phases aboue 1300°K and at 1 atm CO(g) pressure in each M-C-O system have been determined. Pourbaix-Ellingham diagrams have been constructed and are used to estimate the minimum temperatures necessary to obtain these metals by carbothermic reduction under reduced pressures. TANTALUM, columbium, and vanadium react with carbon to form the M,C and MC carbide phases. The M,C carbides have narrow homogeneity ranges, but the MC phases possess considerable ranges of homogeneity.' The free energies of formation of the MC carbides were recently measured, and those of MC and M2Ccarbides have been estimated., (The notations MC and MC denote, respectively, the carbide compositions at the carbon-rich and at the metal-rich boundaries of the homogeneous MC phase.) In this paper, these carbide data are combined with thermodynamic data for the oxides to predict the stable phases in the Ta-C-O, Cb-C-O, and V-C-O systems at specified temperatures and oxygen pressures. M-C-O PHASE DIAGRAMS The solid phases in equilibrium above 1300°K for each M-C-0 system are shown in Figs. 1, 2, and 3. Above 1300°K, the vapor would consist entirely of carbon monoxide; and these phase diagrams were obtained by specifying the vapor pressure of CO(g) to be 1 atm. The temperature at which any two solid phases become unstable is specified along the two-phase equilibrium lines in each diagram. To simplify the diagrams, all solid phases in the Ta-C-O and Cb-C-O systems are represented as stoichiometric compounds. However, the homogeneity ranges of VO and VC are indicated, because they form a complete series of solid solutions.3 It also should be noted that the homogeneity range of

Jan 1, 1964

By S. R. B. Cooke, H. S. Choi, I. Iwasaki

In a previous article1 the function of various fatty acids as collectors for iron ores was reported for the two alternate processes; (a) the flotation of iron-oxide minerals, and (b) the flotation of calcium-activated siliceous gangue. The selectivity of separation was shown to be markedly dependent not only on such common parameters as pH and the levels of collector and activator addition, but also on the structure and the degree of unsaturation of the acids used. The iron ores employed consisted primarily of hematite, goethite, and quartz and as the effectiveness of any one acid on the separation depends on the individual response of each constituent mineral toward the given collector, a comprehensive knowledge of the floatability of the individual minerals is desirable for the interpretation of the results obtained. The mechanism by which a collector ion becomes attached to a mineral-solution interface has been a subject of much investigation. From quantitative studies of the properties of the electrical double layer on mercury2 and on several solid surfaces3,4,5,6 , the adsorption of some flotation reagents at the mineral-solution interface is beginning to be understood. For example, it has been demonstrated from streaming potential measurements made on quartz5 and corundum6 that the interfacial electrical condition is strongly dependent on the pH. Thisoccurs presumably through the following electrolytic reaction at the interface, and in the presence of a flotation collector, controls the floatability of the solids. A concurrent investigation of the flotation behavior of goethite and of quartz carried out at the School of Mines and Metallurgy7 has shown a positive correlation with the electrokinetic behavior of these minerals. The purpose of the present investigation was to collect general information on the floatability of hematite, and to investigate the function of various 18-carbon aliphatic acids on the floatability of hematite, goethite, and of activated quartz. Electrophoretic mobility measurements, simplified flotation tests using a modified Hallimond tube, and contact angle and frothability measurements were employed. The results are of direct application in the interpretation of the batch flotation results on natural ores as

Jan 1, 1961