Search Documents

By AIME AIME

THE Board of Directors of the Institute has authorized the appointment of a committee to draw up rules of procedure under which awards can be made from time to time to petroleum engineers for outstanding contributions to the art of finding and producing oil and gas. These awards will 11e sponsored by the Petroleum Division and are the first recognition by any professional society of outstanding achievement in "oil mining." They will be in the form of either a gold medal, scholar- ship, or other suitable prize. The awards will be financed from the income of the Anthony F. Lucas Memorial Fund, which was started about fifteen years ago, shortly after' his death, by admirers of Captain Lucas.

Jan 1, 1936

By M.A. Hunter

This paper gives the results of an investigation of the specific resistance and temperature coefficient of the electrical resistance of nickel and its important alloy, monel metal. For most of the pure metals, the temperature coefficient of resistance is approximately 0.004 per degree centigrade at 20" C. Nickel and iron, however, are exceptions. This property is important as it gives us good material for the construction of thermometers and other instruments involving electrical control. A summary of information on this subject has been publishcd by the Bureau of Standards.l The present experiments antedate this publication by several years and as the information obtained is not contained in it, the results of the experiments arc published as additional information. Electrical Properties of Pure Nickel It is generally conceded that the lowest values for electrical resistance are obtained in the purest metal. In the case of nickel, the best material obtainable is electrolytic nickel, which contains approximately 99.80 per cent. nickel, 0.15 per cent. iron, and 0.05 per cent. copper. Any cobalt that may be present is included in the nickel figure. If the elcctrolStic sheet has been deposited without intermission, it is possible to cut a section from the sheet and roll it into wire without melting. By this means a nickel wire may be obtained that is uncontaminated by any of the impurities always taken up by nickel during melting. Two samples of nickel wire obtained from different electrolytic nickels had the follolving electrical resistance and temperature coefficient of electrical resistance: Specific Temp. CofEE. Sample MateRial ReSISTance peR Deg. C. NO. 1 Electrolytic nickel.................... 7.55 0.00550 NO. 2 Electrolytic nickcl ................... 7.60 0.00553 * Rensselacr Polytechnic Institute. Director of Research, Driver-Harris Co. Russell Sage Laboratory, Rensselaer Polyt,ecllnic Institute. 1 U. S. Bureau of Standards, Circular 100 (March, 1921).

Jan 1, 1923

By M. A. Hunter

This paper gives the results of an investigation of the specific resistance and temperature coefficient of the electrical resistance of nickel and its important alloy, monel metal. For most of the pure metals, the temperature coefficient of resistance is approximately 0.004 per degree centigrade at 20" C. Nickel and iron, however, are exceptions. This property is important as it gives us good material for the construction of thermometers and other instruments involving electrical control. A summary of information on this subject has been publishcd by the Bureau of Standards.l The present experiments antedate this publication by several years and as the information obtained is not contained in it, the results of the experiments arc published as additional information. Electrical Properties of Pure Nickel It is generally conceded that the lowest values for electrical resistance are obtained in the purest metal. In the case of nickel, the best material obtainable is electrolytic nickel, which contains approximately 99.80 per cent. nickel, 0.15 per cent. iron, and 0.05 per cent. copper. Any cobalt that may be present is included in the nickel figure. If the elcctrolStic sheet has been deposited without intermission, it is possible to cut a section from the sheet and roll it into wire without melting. By this means a nickel wire may be obtained that is uncontaminated by any of the impurities always taken up by nickel during melting. Two samples of nickel wire obtained from different electrolytic nickels had the follolving electrical resistance and temperature coefficient of electrical resistance: Specific Temp. CofEE. Sample MateRial ReSISTance peR Deg. C. NO. 1 Electrolytic nickel.................... 7.55 0.00550 NO. 2 Electrolytic nickcl ................... 7.60 0.00553 * Rensselacr Polytechnic Institute. Director of Research, Driver-Harris Co. Russell Sage Laboratory, Rensselaer Polyt,ecllnic Institute. 1 U. S. Bureau of Standards, Circular 100 (March, 1921).

Jan 1, 1923

By H. W. McQuaid

IT IS usually assumed that chemical specifications are sufficient for steel to be used for case carburizing, and if the steel analyzes within the ordinary limits specified for steel for this purpose, no difficulty traceable to the steel used should be encountered in obtaining satisfactory results in the case carburizing and hardening. Much work has been done to determine the effect of various alloying elements on the rate of carbon penetration, etc. but, to our knowledge, little if anything has been published in regard to the effect of the quality of the steel on the final results in the hardening of case-carburized steel parts. The writers believe that the structure of the case both before and after quenching is greatly affected by the actual condition of the steel itself as made, and that for good results in the case-carburizing and hardening departments, the steel should be of the best possible quality as regards non-metallic impurities. It is the purpose of this paper to prove that the presence of excess dissolved oxides in the steel, as made in the melting furnace, affects permanently the results obtained in carburizing and hardening and that it is possible that the presence of dissolved oxide can result in total unfitness of low-carbon steel for, case hardening purposes. When races and rolls for roller bearings are made from a low-carbon steel, case carburized and hardened, it is of primary importance that the results of this treatment be of the highest quality. It is necessary, therefore, that in the case-carburizing work each detail be rigorously checked to avoid any defects which would cause the loss of much time and material. The case carburizing with which this paper deals was done in under-fired oil furnaces. The temperature of each furnace is controlled by means of a platinum platinum-rhodium thermocouple, in connection with a potentiometer indicator and potentiometer recorder. The temperature of each furnace is registered every 15 min. by an operator, who is continually checked by the automatic recorders.

Jan 2, 1922

By Robert Mehl

THE purpose of this investigation was to prepare high-purity iron-carbon alloys, to determine as precisely as possible the A3(GOS), the Acm(SE), and the A1(PSK) transformation temperatures in the meta-stable iron-iron carbide system (up to 1.4 per cent C), and to study the influence of carefully controlled and constant rates of heating and cooling (1/8 to 2° C. per minute) upon the transformation temperature and upon the resulting microstructure. Apart from the general metallurgical importance attending the completion of such a task, it will be noted that highly precise transformation temperatures are of interest and importance in the thermodynamic study of this system1. Several determinations of the iron-iron carbide diagram have been made. These suffer generally from the low purity of the alloys used, and from the application of methods of investigation of low sensitivity. Attempts to compare and weight the many data available in an effort to construct as accurate a diagram as possible have, in the main, been unsuccessful. In general, the wide differences in the results of different workers, the lack of complete analytical data, the omission of important details relating to the heat-treatment of the alloys, and the meager description of the methods of investigation applied, render such a process of averaging nearly meaningless. It may be seen from the summaries by Epstein2 and Körber and Oelsen1 that variations as great as 30° C. exist in the reported data on the A3 temperatures in iron-carbon alloys. For-tunately, the A3 temperature in pure iron is now known to be 910° C. ± 1° C.3 The best recent work on iron-carbon alloys is that of Esser4 on hypoeutectoid steels and that of Sato' on both hypoeutectoid and hyper-eutectoid steels.

Jan 1, 1937

By H. Y. Jennings

An extensive field and laboratory experimental program was carried out to compare the waterflood behavior of carefully preserved soft and unconsolidated cores with measurements on the same cores after extraction. Results obtained from using idealized consolidated and unconsolidated porous media in which wettability could be carefully controlled were contrasted with the preserved core data. The controlled tests on idealized porous media investigated the effect of wettability, flood rate, core length, core permeability and consolidation on the displacement of high viscosity oils. It was concluded from these studies that waterfloods are more favorable when carried out with crude oil in preserved soft and unconsolidated cores than with the same cores after they have been extracted and re-saturated. Waterfloods are usually more favorable when carried out with crude oil in extracted .soft and unconsolidated cores than with refined oil of the .same viscosity in the same cores. The less favorable behavior of extracted soft and unconsolidated cores compared to preserved cores is due to alteration of the core by extraction. Preserved cores saturated with native water and oil should be used for laboratory displacement experiments because they more accurately reflect true reservoir behavior INTRODUCTION The demand for low gravity crude oil created by refinery modernization has focused attention on increasing the production of this viscous crude oil. Billions of barrels are in place in fields that are depleted, or nearly depleted, by primary production mechanisms. Since low gravity reservoirs are relatively recent, geologically, the solid matrix material is usually soft and unconsolidated sand. Such formations are also characterized by a high clay content. Evaluation of sophisticated oil recovery processes with the associated high capital investments has increased the demand for special core analysis tests on material from these soft and unconsolidated sand reservoirs. Data in this paper have resulted from an extensive field and laboratory experimental program. The initial objective vras to provide soft and unconsolidated sand cores for laboratory measurements with as little alteration as possible from their reservoir condition. A secondary objective was to compare the waterflood behavior of these carefully preserved cores with measurements on the same cores after they had been extracted and resaturated. When the comparison showed markedly different behavior the final objective was to attempt to explain the difference by making measurements on idealized porous media free of clay in which initial wettability could be carefully controlled. EXPERIMENTS MATERIALS Core Material The preserved cores used in this study were obtained with as little alteration as possible from their reservoir conditions. Special techniques were developed to satisfy this objective. The cores were cut with native crude whenever the crude had the necessary properties to satisfy the minimum drilling fluid requirements. A pure hydrocarbon chromatographic tracer was added to the crude to provide a simple, safe and inexpensive method to distinguish between oil filtrate and formation oil. Details of the tracer technique used in this study and the procedures used to handle and process the soft, unconsolidated cores have been published.' The core samples were then preserved and packaged at the well site with a dip-applied strippable plastic, or by using a rubber sleeve from a rubber-sleeve core barrel. The final step was to insure that the carefully taken and preserved samples were not altered by processing in the laboratory. Some soft and poorly consolidated sands were carefully shaped in the lab and encased in a protective mounting without disturbing their three-dimensional integrity. Many samples were so poorly consolidated that they literally flowed from the package when the seal was broken. A technique was developed to obtain cylindrical plugs from these samples by using liquid nitrogen as the drilling fluid in a conventional core-drill, drill-press assembly. The idealized porous media consisted of sintered rods of Alundum RA 139, outcrop sandstone identified as Al-hambra sandstone and packs of No. 130 Nevada sand. This sand is 95 per cent 140-200 mesh. (Physical properties of these porous media with those representative of preserved cores are in Table 1.) The natural cores and most of the idealized porous media were 1 1/2-in. in diameter and 3-in. long. The samples used to study the effect of core length were 1 1/2-in. in diameter and 12-in. long. Liquids Water and oil produced from the formations being studied were protected from the atmosphere and collected in carefully cleaned glass or plastic-lined containers. The production was free of chemical additives such as emulsion breakers and corrosion inhibitors. The crude oil was

Jan 1, 1967

By M. R. Campbell

Coal is the geological product of entombed vegetal tissues. This view of its origin led Stopes and Wheeler to define it as "mummified plants." They evidently intended this term to be used in a broad way and to mean the preservation of the organic material, as such, regardless of the means employed to accomplish the purpose. The term " coal" should be regarded, therrfore, as broadly generic, and applicable to all accumulations of vegetal tissues as soon as they are covered and protected either by water or by earthy material. In this sense peat should be regarded as the first stage of coal formation and the term coal should include the resultant products of transformation in all other stages of the process until they have lost all resemblance to the original matter from which they were derived. If this idea of the development of coal is accepted and it is admitted, as the geologists claim, that the forces which produced this transformation of the coal have been active since vegetation began to grow upon the land, and are still in operation, it is obvious that somewhere in the world there are all gradations of this material from peat just forming in the swamps of today to graphitic anthracite which presumably marks the most advanced stage that can be recognized with certainty as belonging to the series. Some of these coals, particularly those occurring in the upper part of the series, are fairly well known because they are the ones that are most widely distributed and have been mined and utilized most extensively. On the other hand, the coals in the lower part of the series are but little known because they are not so abundant and, owing to their relative inefficiency, have been only slightly exploited and utilized, especially in regions where the better coals are abundant. The result of these conditions is that much research work has been done on coals of the higher ranks and a great body of facts regarding their physical and chemical properties and the uses to which they are best adapted has been accumulated, but little information is available regarding the coals of the lower ranks. Many able scientists, particularly chemists, have attempted to bring some order of the chaos of coals of various compositions and uses by

Jan 1, 1930

By Stephen C. Blair

Laboratory permeability measurements at elevated pressure and at temperatures ranging from 20º to 150°C have been conducted on samples of Ironton-Galesville sandstone. The purpose of this testing was to identify and characterize important physicochemical processes occurring in association with the injection and withdrawal of heated ground water at the U.S. Department of Energy's Aquifer Thermal Energy Storage (ATES) field site in St. Paul, Minnesota. Results indicate that permeability decreased significantly as temperature was increased and that dissolution of the dolomite and silicate cementing agents and accompanying changes in mechanical properties may occur in the heat storage aquifer at St. Paul. Further, loss of permeability with temperature in laboratory samples may be caused by the change in the mechanical structure of the sample. Tests at ambient temperature to evaluate the effect of particle migration under conditions of reversed flow indicate that this process will not significantly impair formation permeability at the St. Paul site.

Jan 1, 1984

The Garfield plant of the American Smelting & Refining Company is situated about seventeen miles west of Salt Lake City, on the Los Angeles & Salt Lake Railroad, and has freight service by the Denver & Rio Grande Western. Western Pacific and Bingham & Garfield Railways. The site lies between the picturesque Great Salt Lake, with its mountain islands and the northern point of the Oquirrh Range, which forms the western boundary of the Salt Lake Valley.

Jan 1, 1925

By H. O. Hofman

The mining and metallurgical laboratory, as we understand the term in this country, is a place .in which mechanical and chemical working-tests are made on ores, fuels and furnacematerials. It is of quite recent origin. The first laboratory of this kind to be used in connection with teaching was put into operation in 1871 at the Massachusetts Institute of Techilo1ogy. † The idea had already existed in the mind of President W. B. Rogers when he wrote, in 1864, his pamphlet 'on " The Scope and Plan of the School of Industrial Science of the Massachusetts Institute of Technology;" but several years elapsed, and an extended visit to the mines and mills of Colorado, Utah, Nevada and California was required before this idea could take a form adapted to the purposes of original research as well as of instruction. The laboratory was given from the first into the charge of Prof. R. H. Richards, who, by improving its methods and enlarging its scope, has brought it to the position which it occupies to-day as the leading representative of its class. Private laboratories for making tests upon ores had previously existed here and there, especially on the Pacific coast, for silver and gold ores; but in the educational field the

Jan 1, 1896

By B. P. Mulcahy

When the phrase "selection of coal for carbonization" is used, there is always the implied continuance of thought "to make good coke.'' The reason for this, of course, lies in the fact that, in almost all instances, when coal is carbonized coke is the principal product. Under certain conditions the yield of gas may also be a factor, but even here it must be secondary to the coke yield, for in every instance coke represents the largest single product of the process. The importance of coke to the byproduct industry has been considerably enhanced during the past 20 years because of the continuously decreasing financial returns of all the by-products. This fact will account, in part, for the rebirth of interest and investigation in the carbonization process during the past 10 years. Many papers have been written on this subject, with naturally divergent thoughts because of the diversity of interests, but in each instance the common aim was the same—the making of better coke. Scope of Investigation In perusing this literature, the writer was struck with the constantly recurring imposed condition of asking for better coke, but with the distinct unwillingness to make any concession to temperature of carbonization. When there is a high demand for coke, the only means by which the industry can increase the quantity is to shorten the coking time by an increase in temperature, or to increase the quantity of low-volatile coal, or both; and since in many instances the percentage of low-volatile coal can be increased only in small quantities, because of factors to be discussed later, the big increase must come from shortening the coking time. When this is done most of the improvement accomplished by the selection of the coals in the mixture is lost. It is not felt necessary in this paper to discuss the advantages of minimum ash and sulphur and other materials in coal. The value of minimum contents of these materials in coke is well established. When the use of coals high in these contents is dictated, the selection of coals, as we will consider it here, cannot apply to full advantage. The scope of this paper, then, will be to discuss the factors of inherent coal characteristics and operating procedures that influence coke quality, for they are fundamentally related and both must be considered if we are to attain our objective of better coke. A study of either must embrace a study of both simultaneously. To properly evaluate the influence of the coal and to help in the selection, we must first be able to appraise the coke, and interpret fairly the influence of the process in all of its aspects. Appraisal of Coke To refer simply to the quality of coke gives no indication of what is meant, for the term is too general in its implication. An analysis of a coke is divided usually

Jan 1, 1944

By B. P. Mulcahy

When the phrase "selection of coal for carbonization" is used, there is always the implied continuance of thought "to make good coke.'' The reason for this, of course, lies in the fact that, in almost all instances, when coal is carbonized coke is the principal product. Under certain conditions the yield of gas may also be a factor, but even here it must be secondary to the coke yield, for in every instance coke represents the largest single product of the process. The importance of coke to the byproduct industry has been considerably enhanced during the past 20 years because of the continuously decreasing financial returns of all the by-products. This fact will account, in part, for the rebirth of interest and investigation in the carbonization process during the past 10 years. Many papers have been written on this subject, with naturally divergent thoughts because of the diversity of interests, but in each instance the common aim was the same—the making of better coke. Scope of Investigation In perusing this literature, the writer was struck with the constantly recurring imposed condition of asking for better coke, but with the distinct unwillingness to make any concession to temperature of carbonization. When there is a high demand for coke, the only means by which the industry can increase the quantity is to shorten the coking time by an increase in temperature, or to increase the quantity of low-volatile coal, or both; and since in many instances the percentage of low-volatile coal can be increased only in small quantities, because of factors to be discussed later, the big increase must come from shortening the coking time. When this is done most of the improvement accomplished by the selection of the coals in the mixture is lost. It is not felt necessary in this paper to discuss the advantages of minimum ash and sulphur and other materials in coal. The value of minimum contents of these materials in coke is well established. When the use of coals high in these contents is dictated, the selection of coals, as we will consider it here, cannot apply to full advantage. The scope of this paper, then, will be to discuss the factors of inherent coal characteristics and operating procedures that influence coke quality, for they are fundamentally related and both must be considered if we are to attain our objective of better coke. A study of either must embrace a study of both simultaneously. To properly evaluate the influence of the coal and to help in the selection, we must first be able to appraise the coke, and interpret fairly the influence of the process in all of its aspects. Appraisal of Coke To refer simply to the quality of coke gives no indication of what is meant, for the term is too general in its implication. An analysis of a coke is divided usually

Jan 1, 1944

By R. H. Cox, A. S. Allen, James Paone

The southwestern Illinois communities of Belleville and Maryville lie within the greater metropolitan area surrounding St. Louis. Missouri. They also lie within that part of the Illinois coal basin where the Number 6 coalbed has been mined for more than a century. About half the coal was left as pillars to support the ground surface. Years later, however, damaging movements are affecting buildings, streets, and public utilities in some areas. They are generally believed to be related to abandoned mine workings. The threat of continued or increasing incidence of damage raises the need to explore other subsidence-control measures for protecting affected areas with high population density. Because of experience gained in a subsidence-control program of backfilling abandoned coal mines in the Applachian region and in Rock Springs, Wyoming, the Bureau of Mines was called upon to investigate the subsidence occurrences at Belleville and Maryville, and recommend protective measures. Funds ware appropriated for the Bureau to initiate subsidence-control projects at two residential sites in Belleville and one in Maryville. Subsurface investigation of the sites by diamond core drilling revealed two conditions that differ from those encountered at most sites of previous subsidence-control projects. The mine workings were found to be dry and the mine floor consisted of soft underclay which characteristically loses strength with increase of moisture. It had been anticipated that water would have percolated into the mine workings at one .or more of the sites through cracks resulting from subsidence. Under such conditions Bureau engineers believed that injection of mine waste by the pumped; slurry technique3 would provide support and stabilize any movements initiated by the softening of the clay. With discovery that the underclay deposits at the three sites have apparently not been exposed to water since the mines were operating, hydraulic backfilling of any type was considered inadvisable on the basis of present knowledge. To avoid introducing water, a portable pneumatic system is being devised for injecting minus 0.01 27 m (1/2 in.) mine waste into the mine workings. Machines for pneumatic backfilling have been used in Europe not only for subsidence protection but also for strata control, for reducing spontaneous combustion and methane accumulation, and as a means of waste disposal. The Bureau experimented with a pneumatic machine in the Northern anthracite field of Pennsylvania in the 1950's. Previously pneumatic machines have been installed in active mine workings discharging from horizontal pipelines which conveyed air- borne material into rooms to be filled. In the present adaptation to abandoned mines, the machine and air compressor will be operating at the surface, to impel material vertically down injection boreholes with sufficient air pressure to disperse fill material laterally in mine workings at the base of injection holes. Large diameter access and ventilation boreholes will be provided at one site for entry into mine workings to observe backfilling progress. The Belleville and Maryville projects are part of the Mined Land Demonstration Program of the Bureau of Mines. The Illinois State Geological Survey and Department of Mines and Minerals are furnishing technical support.

Jan 1, 1979

By R. J. Stevens

THE Roan Antelope Smelter commenced operations in October, 1931. As originally designed, its equipment consisted of one reverberatory furnace, 120 X 25 ft, two Peirce-Smith converters 12 X 20 ft, and one straight line casting machine. Since that time the following additions have been made: One reverberatory furnace 120 ft X 28 ft (1934) One reverberatory furnace 95 ft X 28 ft (1943) Two 12 X 20 ft Peirce-Smith converters (1934 and 1938) One 13 X 30 ft holding furnace 6 (1938) One straight line casting machine and 2 ladle tilting quadrants (1934) The metallurgy of the smelting process is comparatively simple. However, there are several features of operation which are uncommon to most copper smelters: (1) The high grade of concentrate treated; this has always been about 50 pct copper. (2) The high flux burden on the charge. This is necessary because of the deficiency of bases'in the concentrate and the high alumina content of the concentrate. (3) The frequent necessity of adding coal to the furnace charge to control the matte grade. (4) The high grade of matte produced. This has led' to unusual converter problems. From the commencement of operations, the ore mined has come from the Roan Basin orebody. The concentrate produced from this ore consists mainly of chalcocite and shale with small proportions of other copper minerals. As mining operations extend to the Roan Extension orebody, the proportions of bornite and chalcopyrite in the concentrate will increase with a corresponding decrease in the copper content of the concentrate. Because of the concentrate grade the capacity of the reverberatory . furnaces in terms of tons of copper produced per ton of coal burned is high.. This ratio is usually over 2.2, and on especially favourable runs has reached 2.6. Reference to Table , shows that the iron content of the concentrate is unusually low. Only part of this iron is available for slag formation, the balance going to the matte. To make up this deficiency in bases, limerock is added to the furnace charge. This flux ensures a slag that is of the correct silicate degree, is sufficiently fluid, of low specific gravity, and it counteracts the thickening effect of the alumina present. An ample supply of flux is obtainable from Ndola, 2 2 miles distant by rail. Although the reverberatory slag has a high copper content, the slag fall is low and the copper loss in the slag now rarely exceeds 1.0 pct of the total copper charged. The blister copper shipped is of such purity that only one fire refining operation has been necessary to produce a wirebar with properties comparable to electrolytic copper. Bismuth has always been the most troublesome impurity and consequently the problem of its control in the finished product has been of prime importance. Practically none is removed in the reverberatory furnace. The bulk of the elimina-

Jan 1, 1947

By R. L. Wiegel

The two questions considered in this study are: (1) what similarity is there in the liberation of magnetite from various iron formations, and (2) how is this liberation affected by the size reduction technique employed. Twelve sample suites were obtained from commercial concentrators processing magnetite iron formation in the United States, Canada, and Australia. These samples have grades in the range 15 to 45% magnetite iron and approximate mineral grain sizes o f 50 to 2000 microns. Efforts were directed at measuring the liberation characteristics of the samples obtained from the concentrators primary grinding mills. The Davis tube, a laboratory magnetic separator, was used to concentrate individual size fractions of the size reduction product to determine liberation data. These liberation data were compared with relationships calculated from a highly idealized mathematical model of liberation in a binary mineral system. The results of these comparisons have been encouraging for nine or ten of the twelve samples tested. This leads to the conclusion that for most commercial iron formations, at least with conventional rod mill size reduction, it is possible to quantitatively characterize liberation with two parameters: an effective mineral grain size and ore grade. Limited laboratory size reduction tests as well as one of two sets of liberation data from commercial primary autogenous grinding lend some support to the contention that autogenous grinding can affect mineral liberation.

Jan 1, 1976

By Richard McCaffery

WHEN we began the study of blast furnace slags we limited our work at first to a study of those slags containing only lime, alumina and silica. On our paper1 on some of the results of this first work, the solubility of sulfur in slags containing no magnesia was reported and the question of sulfur solubility and slag viscosity discussed. There has been, for a long time, a very great difference of opinion among metallurgists as to he effect of magnesia in blast furnace slags, and the literature is full if expressions of the most contrary opinions on the subject. As a result, our next publication' developed the constitution of slags considered as a four-component system, silica-alumina-lime-magnesia, and advanced an explanation of slag structure which accorded with the facts and with scientific theory. The present paper continues our study of the general subject of slags. As blast furnace slags are included in the silica-alumina-lime-magnesia system, which is a particular case of four-component solutions, we have determined that there are 22 components Table 1), which may enter into the silica-alumina-lime-magnesia system and that 10 or 12 of these components may be present in blast furnace slags which are within the ordinary ranges of composition. To cave a very definite conception of the behavior of these components in a slag, we have developed the theory of the cooling of a four-component solution from the liquid state to the solid and the conclusions that we obtained have been made use of in this paper. On account of the importance of the four oxides and 18 compounds which enter into the silica-alumina-lime-magnesia system, some method of calculating the percentages of the various compounds that are present in the slag when the percentages of the oxides are given, seemed very desirable and we develop L method later herein for doing this, and finally we give illustrations of the composition of a wide series of blast furnace slags and show some applications of these composition data.

Jan 1, 1927

By ROBERT. RICHARDS

I. INTRODUCTION The object of this paper is to enlarge the field of settling velocities treated by me in my former papers, Close Sizing Before Jigging, and Sorting Before Sizing.' There seemed need of work both on coarser and on finer sizes. Messrs. A. Sidney Warren and M. L. Nagel undertook the investigation for the coarser sizes, from 12.85 mm. down to 2.05 mm. diameter. Their work, because of the closer spacing and because of the increased number of observations and consequent stronger averages, called for a revision of the former work. Messrs. G., A. Barnaby and Ralph Hayden undertook this part of the work, from 2.49 mm. down to 0.28 mm., which is near the limit of sifting. Their work covers the ground much more minutely and comprehensively than the former papers. There remained to be covered the portion of the field too fine for investigation with the sieves. This part, covering the range of grains from 0.48 to 0.03 mm., was undertaken by Mr. E. S. Bardwell. For it he used the elutriation method. II. THE FIRST, OR COARSEST, SECTION OF THE FIELD. The first desideratum in this investigation was a series of sieves for sizing the sands preparatory to making the tests. It became necessary, therefore, to decide on a sieve-scale for this purpose. A sieve-scale is a series of sieves in which the dimensions of the holes of the successive members form a series increasing by a. definite ratio. There are three natural sieve-scales : 1, progressing by doubling the width of the hole for each suc-

May 1, 1907

By R. B. Woodworth

In the sinking of bore holes, there are but two fundamental operations —drilling and hoisting—which determine in the main the character of drilling mechanism and structures. There are endless ramifications, however, in the execution of these fundamental operations, according to the purposes for which the bore holes are drilled, their maintenance after completion, the protection and convenience of workmen, etc. The three main lines of use for bore holes are in mineral exploration, the sinking of water and salt wells, and the exploitation of pqtroleum and natural gas. This paper has to do more especially with the last. Here again there are many divergences. Wells may be drilled by either the percussive, the hydraulic, or the abrasive method. Finally, each of these methods, as applied by drillers of diverse nationalities, has followed somewhat different lines of development. The American system of cable-tool drilling has perhaps had the widest application; the hydraulic rotary is also in extensive use; but the Canadian system, the Galician system, and the Russian free-fall system all have their points of recognized merit and are preferred by operators accustomed to their use. These differences in drilling procedure, which rest ultimately on essential variations in geological conditions, are reflected in the drilling structures as well as in the drilling mechanism. The purpose of the present paper is to record those stages in the development of the application of steel to the construction of drilling mechanism and structures with which the writer has been intimately associated, and to contribute to the history of the art of drilling other data acquired in the course of his personal investigations. It is necessarily limited by reason of space to American practice, with especial reference, therefore, to the cable-tool system and the hydraulic rotary method of drilling wells for oil and gas.

Jan 1, 1916

By Richard H. Olson

"Rarely in our technological society does the discovery of a new class of inorganic materials result in such a wide scientific interest and kaleidoscopic development of applications as has happened with the zeolite molecular sieves." The foregoing, the opening sentence in a landmark volume on zeolite molecular sieves by D. W. Breck (1974), is, if anything, an understatement. Zeolites were recognized as a new group of minerals in the 1750s, but it was not until 1930 that the first analysis of the crystal structure of a zeolite mineral was made. In the late 1940s research workers at Union Carbide Corp. began a program of zeolite synthesis and study which has resulted in one of the major research achievements of all time. Naturally, with the vast research and development efforts devoted to the synthetic molecular sieves, Union Carbide became concerned in the mid-1950s about its position should minable deposits of natural analogues be discovered. Zeolite minerals have diverse origins, and even a brief discussion of these is beyond the scope of this paper. The early work on zeolites was confined to igneous rock occurrences (e.g., amygdules and veins) which were formed by "space-filling;" these crystals tend to be euhedral, thereby rendering them appealing to both mineralogists and collectors. During the first year or so of Union Carbide's exploration (which began in mid-1957) attention was devoted solely to such igneous occurrences. A landmark paper by Bramlette and Posnjak (1933) heralded the potential significance of the occurrence of zeolite minerals as alteration products of vitric ash and similar materials. In the summer of 1958, full attention was directed by Union Carbide to the search for deposits of this type in the western United States. Since then, such exploration has been continu-

Jan 1, 1975

By M. R. Geer, H. F. Yancey

Four coals were treated in the Humphreys spiral concentrator, and the products were examined by float-and-sink and screen-sizing tests to determine fundamental performance characteristics. The efficiency of the separation between coal and impurity was shown to be influenced greatly by particle size.

Jan 1, 1950