Search Documents

By Thomas L. Garrard, James A. Sprague, Rex B. McLellan, Samuel J. Horowitz

A simple rnodel for interstitial solid solutions has been devised in which each solute atom interacts with the solzlent lattice in such a way as to exclude an integral number of nearest-neighbor sites from being occupied by solute atoms. The vemaining interstitial sites ave not affected. In calculating the entropy of such a solution the increase in the number of interstitial sites available to solute atoms due to the ozlerlap of blocked sites is taken into account. The ther-modynamic functions and the solute activity fov the solution rnodel are calculated. It is shown that considevation of the overlap sues vise to a correction term of the order 8' ( where 0 is the ratio of solute to solvent atoms) in the thevmodynamic functions of the solution and the solute activity. The theo,uetical equation for the solute activity was used to analyze the available data for the activity of carbon in austenite at three different temperatures. The use of a computer enabled many comparisons to be made between the experimental activity data and those predicted by both the complex blocking model and the simple, widely used blocking model in which the ozierlapping of blocked sites is not taken into consideration. Even though at the highest concentvations oj carbon the value of 0 is small it is shown that the best fit to the experimental data is found with the complex blocking model. RECENTLY it has been shown by analysis of gas-solid equilibriums that many interstitial solid solutions can be described by the quasi-regular solution model in which the partial energy of solution E, is independent of composition and, apart from a composition-independent term due to nonconfigurational factors, the partial entropy is that of an ideal solution. Dilute solutions of nitrogen in both bcc and fcc iron,' dilute solutions of oxygen and silver,' carbon in a Fe,' and dilute solutions of carbon in ? Fe2 are all quasi-regular. In addition many hydrogen-metal solutions, both dilute and concentrated (with the notable exceptions of the H-Ni and H-Pd systems), can be described by this model.3 However, it has been shown that, at various temperatures, solutions of carbon in ? Fe begin to depart strongly from quasi-regular behavior at low concentrations. A plot of the activity of carbon in ? Fe relative to pure graphite vs atom fraction of carbon (Cc) calculated from Smith's data4 begins to depart from the (nonlinear) plot for a quasi-regular solution at about Cc = 0.02. Several statistical models have been proposed to account for the thermodynamic behavior of carbon in y Fe. Darken and smith4 set up a model in which a carbon atom in its octahedral site in the fcc lattice has either one or no neighboring carbon atoms in the twelve nearest-neighbor octahedral sites. It is assumed that the number of carbon atoms having more than one nearest neighbor is negligibly small and that a solute atom does not interact with another solute atom located at a greater distance than the first shell of interstitial sites. Thus this model contains two characteristic interaction energies. Darken and Smith showed that this model gives reasonable agreement with the measured variation of carbon activity ac with composition. It is noteworthy that Darken and Smith concluded from their analysis of the activity data using this model that there was a repulsive force between carbon atoms in austenite which reduces the concentration of C-C pairs below that corresponding to random mixing. Recently Aaronson, Domian, and pound5 have considered in detail the statistical model developed by Lachere and by Fowler and Guggenheim7 and have shown that it is compatible with the activity data for carbon in austenite. In Darken's model the energy of solution of carbon in austenite is dependent on temperature and concentration; the departure from Henry's law arises from the concentration dependence of the energy of solution. In Aaronson, Domian, and Pound's discussion of the Lacher, Fowler, Guggenheim model the interaction energy wy between adjacent carbon atoms in austenite is strongly temperature-dependent. Aaronson et al . suggested that this temperature dependence of wy and hence the energy of solution of carbon could be explained either by the formation of clusters of carbon atoms (despite the repulsive nature of wy) or by the dual occupancy of the octahedral and tetrahedral sites by the carbon atoms. However, a temperature-dependent heat of solution

Jan 1, 1968

By Edgar C. Bain, William E. Griffiths

The results of an inquiry into the structural nature of some 70 iron alloys containing both nickel and chromium over a considerable range of concentration are briefly described in this paper. This study is a part of a comprehensive program of investigation into alloys involving chromium in progress at the Union Carbide and Carbon Research 1aboratories. All the compositions studied contained carbon in amount comparable to commercial alloys. The B Constituent In addition to locating the limits of composition for the three principal types of structure (polyhedral ferrite, martensite and austenite) and their combinations, certain other features of the system were observed. A hitherto undescribed brittle constituent (designated here as the "B constituent") was discovered. It is very hard, non-magnetic and forms in two modes from chrome-ferrite by recrystallization. It is the stable low-temperature condition for the equal-proportion chromium-iron materials containing less than 10 per cent. nickel. Although it partakes of the nature of an inter-metallic compound, yet it may exist over a considerable range of composition. It is non-existent above a temperalure zone, varying with composition, from 800° C. to 950° C., and heating above this critical temperature develops chrome ferrite persistent after average cooling rate; a few hours just below this temperature will develop the complicated brittle crystalline type. The B constituent, when found in the grain boundaries of alloys of lower chromium content, contributes a serious brittleness removable, however, by heating and cooling rapid enough to prevent its re-format'ion. By suitable means of precipitution, the hard B constituent can be made to strengthen the already stiff alloy matrix in the manner of submicro-scopic particles, as exemplified in duralumin or the Sykes iron-tungsten and iron-molybdenum alloys. A possible explanation is offered for the familiar brittleness developed in chrome iron at temperatures above about 475" C. and removable by

Jan 1, 1927

By John J. Collins

[CONTENTS PAGE Purpose and scopeI Core samplingI Sludge sampling.....7 Combining core and sludge assays13 Deviation and surveying of drill holes17 Conclusions24 Acknowledgments25 Bibliography25] PURPOSE AND SCOPE The purpose of this paper is to review a few of the problems involved in the interpretation of diamond-drill core and sludge samples, with the hope that it will stimulate discussion and bring forth some of the information on the subject that has been accumulated by various organizations. The release of these data would benefit the mining industry as a whole. Particularly valuable would be the details of drilling programs that have been tested by actual mining operations, as most of the available published material is unsupported by production records. The scope of this paper is limited to a few of the commonest problems of interpreting diamond-drill core and sludge samples and the deviation of holes. It does not include the description of routine operations performed by the drillers, nor the estimation of ore reserves. The methods of calculating reserves have been described 25,26,31,32.50,65 but more information is needed on the results shown by actual mining operations. CORE SAMPLING The accuracy of diamond-drill-hole sampling depends in large measure on the percentage of core recovery. As a general rule, the longer the run, the poorer is the recovery. Although the longer runs allow cheaper drilling costs, the determining factor should be the percentage of recovery desired. The problem is one of balancing accuracy against costs. Holes of larger diameter may show improved recovery, except as Joralemon* points out that there are some conditions in which small holes give better core recovery than large holes. This is particularly true, he says, in rocks like shattered quartzite, where larger core tends to break in angular fragments and grind up, while the diameter of smaller core is less than the distance between joint planes and grinding is not so serious. In a large measure the length of the sample run should depend on the type of deposit. Favorable drilling may allow uniform sample runs of 5 ft., 10 ft., or perhaps 20 ft. In veins or beds of relatively narrow widths and changing characteristics, however, the ore zone may be overrun and ground in a core barrel full of waste rock. Generally it is desirable to break the sample at a change in the rock or ore. Such a change, often indicated by a color change in the sludge water, should be a signal for the driller to make a "dry" block and to pull out that run regardless of the length. Such a procedure permits the segregation of waste from ore samples so

Jan 1, 1946

By W. B. Mather

Of the 61 dikes examined some yielded cassiterite, tantalite, and beryl; eight contained spodumene; and six carried amblygonite. Two mines stockpiled spodumene as a byproduct. Only zoned pegmatite dikes carried lithium minerals. GEOLOGICAL studies have revealed the occurrence of hundreds of pegmatite dikes in northeast Brazil, Fig. I, in the three states of Rio Grande do Norte, Paraiba, and Ceara. Heretofore data have not been available on the possible production of lithium minerals from these areas, and in March, April, and May 1953 the author undertook a reconnaissance survey covering a cross-section of the pegmatite~. Sixty-one pegmatites were examined. The pegmatites of Rio Grande do Norte and Paraiba are located in an arid region (Seratao), and except in the most southerly portion there is a minimum of vegetation and overburden. The region is easily prospected and relatively accessible by jeep or truck. The pegmatites examined in Ceara are in an area of lush vegetation along the flanks of the Jaqueribe River valley. It is therefore more difficult to prospect, and the dirt roads, as a means of access, leave much to be desired. For all practical purposes rail transportation, except in Ceara, is not available. The rocks of the area are composed of Pre-Cambrian schist, gneiss, quartzite, and marbles. They have been intruded by granites, monzonites, and diorites and cut by quartz veins and pegmatites. Pre-Cretaceous erosion reduced the area to a peneplain upon which Cretaceous or younger sandstones were deposited. Recent erosion has left only a few remnants of these younger rocks. In most of the Rio Grande do Norte-Paraiba area the pegmatites were more resistant to erosion than the enclosing schists and therefore stand out in relief. This is not true in the rolling country of Ceara, where the pegmatites lack topographic expression. With regard to structure and lithology, the pegmatite~ of northeast Brazil are divided into two types, uniform and zoned. Of the 61 examined, 19 belong to the uniform and 42 to the zoned type. Uniform pegmatites are normally long, narrow, and tabular, with sharp contacts. They are composed of an intimate mixture of feldspar (microcline or ortho-clase), mica (biotite, phlogopite, or muscovite), and quartz. The grain size5 varies from fine at the contact to coarser in the interior. They are not considered a commercial source of pegmatite minerals, although efforts have been made to produce green beryl of gem variety. This type of dike is often abundant in schists and gneisses close to granite intrusives. The productive dikes — lenticular, pod-shaped, or irregular in outline, with sharp contacts — are of the zoned variety. Zone contacts are gradational, except for those with the quartz core. Zones re identified as follows, see also Fig. 3. Border Zone: This outer zone, in contact with the country rock, is composed chiefly of fine-grained muscovite and biotite, with lesser quantities of finegrained microline and quartz. It is the narrowest zone, usually measurable in inches. Wall Zone: Lying between the border and intermediate zones, the wall zone is composed of medium-grained feldspar (often microcline), muscovite, and quartz. Usually it is the widest zone. Widths of 50 ft were noted. Intermediate Zone: Lying between the wall zone and core, the intermediate zone is composed principally of coarse-grained microcline (occasionally with some orthoclase and albite). It may also carry minor amounts of coarse-grained quartz and fine to medium-grained mica. The width varies from less than 3 ft to more than 30 ft. Core: The center of the dike is composed almost entirely of massive quartz, occasionally with minor amounts of fine-grained muscovite. The width reaches 30 ft. Lithium and other minerals of potential economic value are found in the following zones:

Jan 1, 1955

By W. C. Bleimeister

The rock salt deposits of the U. S. occur in five major basins: 1) the Eastern Basin (which includes parts of Michigan, Ohio, Pennsylvania, New York, West Virginia, and Ontario) ; 2) the Gulf Coast Basin (the northern rim of which includes parts of Alabama, Mississippi, Louisiana, Arkansas, and Texas, while its southern rim includes parts of the Isthmus of Tehuampetic and the Yucatan Peninsula of Mexico), 3) the Southwestern Salt Basin (which includes parts of Kansas, Colorado, Oklahoma, Texas, and New Mexico), 4) the Williston Basin (which under- lies parts of North Dakota, South Dakota, Montana, and Saskatchewan), and 5) the Green River Basin (whose periphery underlies parts of Wyoming, Utah, and Colorado). The greatest salt production in the U. S. is obtained from the Eastern Basin,-particularly from the areas of Michigan, Ohio, and Ontario. In 1958 the salt production from these areas amounted to 8.7 million tons or 35.3 pct of the combined total produced in the U. S. and Canada. Of the 24,286,000 tons produced by Canada and the United States, 6,443,000 tons were in the form of rock salt from dry mining, while 17,843,000 tons were produced from wells in the form of artificial brine, the result of dissolving the rock salt formation by fresh water. Three important factors lie behind the location and development of this salt mining area:

Jan 5, 1961

By N. E. Norman

During the past few years the underground mining industry and the big hole drilling industry have been involved in a flirtatious courtship, but until recently this courtship did not appear to be taken too seriously by either party. However, many of the promises made by the big hole industry are beginning to come true. Improvements have been made steadily in techniques of mechanical boring of large diameter shafts, raises and tunnels, thus making the big hole industry a more stable partner in the eyes of the mining industry. The mining industry too has made many changes in planning that make mining more attractive to the big hole industry. If there is to be a marriage between big hole drilling and mining, we should certainly take a look at the background of the big hole drilling industry, and examine the three main features of big hole drilling to determine how each applies to mining. Shaft Drilling Since 1950, numerous large diameter shafts have been drilled using rotary drilling techniques. Most of the larger diameter shafts have been drilled for the AEC for underground nuclear testing purposes. However, since 1960 several shafts have also been drilled for various mining companies, particularly in the United States. In 1967, rotary drilling shafts were either completed or in progress at the mining companies listed in Table I.

Jan 6, 1968

Karl L. Fetters moves to the front of the AIME organization this month as the 1964 President of the Institute. He will take the chair vacated by outgoing President Roger V. Pierce at the Annual Meeting in New York, already well-rehearsed in his forthcoming duties after a year of preparation as AIME President-Elect. Dr. Fetters is highly qualified for his new responsibilities on both the administrative and professional level. For the past five years, he has been vice president for research and development at The Youngstown Sheet and Tube Co. in Ohio, where he has achieved wide recognition as an out- standing metallurgist and executive. A native of Alliance, Ohio, he obtained his early education in the public schools of his home town and displayed a singular precocity when he launched his professional career as a chemist for the Morgan Engineering Co. at the age of 16. His new career, however, was soon set aside in favor of four years of higher education at the Carnegie Institute of Technology, whence he emerged in 1931 with a bachelor's degree in metallurgical engineering. Surprisingly, and perhaps owing to the employment stringencies of the Depression years, the first job his new qualifications earned him was that of stationary engineer at the Cunningham Sanitarium in Cleveland. After two years of ministering to the mechanical ailments of this institution, Dr. Fetters relinquished his post for a more suitable one in the field of metallurgy.

Jan 2, 1964

By Roger H. McConnel

Throughout the world in 1950 there has been extensive exploration for metals, with emphasis on iron, copper, gold, lead, and zinc. Among the features most apparent in reviewing exploration and development are the staggering sums required, the over-riding influence of government policies throughout the world, and the need for intensified search.

Jan 2, 1951

By A. L. Holley

THE general usage of engineers, manufacturers, and merchants, is gradually, but surely, fixing the answer to this question. In every country rails, boiler-plates, and machinery bars, whether hard or soft, are almost universally called steel, when they are made from cast ingots. Other names for the softer steels, such as " homogeneous metal," " Bessemer iron," " Martin iron," and the like, have failed to obtain general recognition. The meaning of the term steel, before it was enlarged to cover newly developing varieties, has been traced, by a recent writer, down through Percy, Shakspeare, and the Bible, in a most interesting manner, from an archaeological point of view. Undoubtedly, it did characterize hardness and other qualities imparted by carbon. It is within the memory of most of us, that all steels were tool steels, and that the soft, structural varieties were introduced-varieties which harden but little, which bend cold, and which, in many physical properties, are akin rather to wrought-iron than to tool-steel. But, since both the hard and the soft steels are made by the same processes, and have their great, distinguishing structural feature in common, viz., homogeneity resulting from fluidity, it has come to pass, despite every other proposed nomenclature, that all the compounds of iron which have been cast in malleable masses, are called steel, the term wrought-iron being still confined to malleable iron made from pasty masses, and hence laminated in structure. No inconvenience has been found, so far, in distinguishing between the more or less carburized products, in general, by the terms " high-steel," " low-steel," " tool-steel," etc., and, in particular, by prefixing the percentage of carbon and other ingredients, to the terra steel. Steels which contain distinguishing ingredients other than carbon, are called "chrome-steel," " titanium-steel," and the like, just as variously compounded bronzes are called "phosphor bronze," "alu¬minium bronze," etc. Thus the combination of several words or symbols, and figures, may completely disclose the characters of the metal, in terms that are subject to no misunderstanding. But inasmuch as several high metallurgical authorities and clever writers have of late proposed to disturb this natural and somewhat settled nomenclature, it seems important to consider the claims of the various classifications. I shall attempt, in this paper, to show

Jan 1, 1876

By H. M. Otte, A. G. Crocker

SLIP, twinning, stacking faults, and precipitates on well-defined planes in a crystal produce traces that are visible on either a polished or an etched surface. The purpose of this note is to establish the usefulness and limitations of the information obtained from such traces when determining the orientation of single crystals or grains in a polycrystal. Attention will be confined specifically to traces produced by octahedral planes in cubic crystals, though most of the remarks can be taken as more generally valid. The problem of determining the crystal orientation is completely solved in principle' and in particular for the special case under consideration.1'2 Tables are available3 in which the orientations can simply be looked up when given the two or three angles between the traces. Thus a quick and simple method is available for obtaining the orientation of a crystal from surface traces. In this note two examples will be given from recently published papers and will show the use of the method with the aid of the Tables, as well as some of the precautions that should be taken in the procedure. As part of an analysis of X-ray Kossel lines, Peters and Ogilvie 4 determined from them the crystallographic orientation of the specimen. They chose a Cu-5.10 wt pct Si alloy that had been partly transformed from the a (fee) phase to the k (hcp) phase. The latter formed as very straight platelets along the octahedral planes of the a phase, and a photograph (Fig. 7 of Ref. 4) was reproduced in the paper4 of the region for which the orientation had been determined from the Kossel lines. Apart from a very small area (about 0.15 mm diam) near the top center of the photograph, the region shown was clearly all of one orientation. Traces in four different directions were readily identified. Starting with the smallest angle and proceeding counterclockwise, the angles between the traces were measured to be 27° 43', 55° 16', 64 3 43 1, and32"26'. These add up to 1802 08 1, indicating a cumulative error of 8'. The correct values should, of course, be taken from the original glass plates, or at least from prints on distortion-free paper, so the precision of the quoted values is actually greater than their accuracy. The solutions can be looked up in the Tables3 in four ways, depending on how the angles are paired, tion for the minutes of arc is required and the solution obtained will be identical for all the four pairs if the values of the angles are not in error. In a practical situation, such as this one, there are several sources of error, so that the four solutions obtained will all be slightly different. An arithmetic average of the four solutions is mathematically incorrect, but may, in special cases, give an answer close to the correct one. A rigorous procedure for refining the orientation has been described by Mackenzie;5 he gives a least-squares method that can be applied, if necessary, to this type of problem. The orientation thus determined can be compared with the one from the Kosel lines and discrepancies larger than the experimental error assigned to nonor thogonality of the X-ray or electron beam to the specimen. Here the example will only be used to illustrate the general procedure for making a very rapid rough check. From measurements on the stereographic projection, Fig. 9 of the paper,4 we can determine that the surface normal is approximately (0.434, 0.704, 0.562). From the Tables3 we find, using 28°, 55" as a good approximation to the first pair (27°43', 55°16'), that the surface normal is (0.453, 0.678, 0.579).* These two values are within 2 deg of each

Jan 1, 1967

By U. N. Bhrany, N. Arbiter

F. C. Bond (Consulting Engineer, Processing Machin-Dept., AllisChalmers Manufacturing Co., Milwaukee) This is a very comprehensive paper. It deals with 1) size distribution functions, 2) energy-particle size relationships, and 3) criteria for grinding efficiency. The method of analysis used consists of tracing the increase and decrease of successive Tyler scale screen fractions as grinding progresses. The treatment is based upon the assumption that the work done in grinding is concentrated entirely upon the coarse size fractions in the mill. It is postulated that when a feed consisting entirely of particles of one size fraction is batch ground that finer fractions increase at a constant rate as grinding progresses, until finally each in turn begins to be ground and to decrease in amount. It is shown that under these conditions the empirical Gates-Gaudin-Schuhmann log-log size distribution plot can be logically explained. It is difficult to imagine any condition of ball mill operation, or any probability analysis, which would result in no grinding contacts on the finer particles present. However, the authors' postulate must be accepted if their conclusions are to be sustained. They conclude that the equation expressing the for mation rate of each size fraction can be resolved into the G.-G.-S. size distribution equation, and that the curvilinear portion of the log-logsize distribution line represents the only particle sizes which are being ground as well as produced. The author's statement that the G.-G.-S. Eq. 4 applies only to the finer portion of the size distribution while the Rosin-Rammler Eq. 6 applies over the whole size distribution range certainly supports the view that an exponential equation of the Rosin-Rammler type corresponds more closely to actual size distribution than does the power law G.-G.-S. equation. However, the G.-G.-S. equation is used to derive Eq. 8 and Eq. 9, which state that the energy required to grind a ton through a particular mesh varies inversely as the particle size to the exponent -a , whic h is the slope of the extended G.-G.-S straight line. This is stated to apply to both batch and continuous grinding. The G.-G.-S. slope exponent thus becomes very important in all crushing and grinding analyses by this method. The authors include some data which can be used to test their conclusions, as described below: We will consider grinding a feed composed of 14 mesh (1190u) to -200 mesh (74u). The average of 17 Allis-Chalmers grindability tests on quartz gives a work index (Wi) of 12.77. The -200 mesh product should have 80 pct passing 41.6u or P = 41.6. The equivalent 80 pct passing size of the 14 mesh feed particles is considered to be the particle diameter, as is true for spherical particles. Thus F is 1190u. In the work index equation 10 wi 10 wi 127.7 127.7 P f 41.6 1190 = 16.1 kw-hrperton. In Table I the ball mill exponent for quartz is 1.0 and from Eqs. 9 and 10: w=kw-hr/ton =Constan/(do/di) = 16.1 ton so that (1190) Constant/ Constant and the Constant equals 259. The tons per horsepower-hour value is 0.0464, in agreement with Table IV. The exponents for other minerals are listed in Tabl e 11. In Table IIA, the kilowatt hours per ton required to grind these minerals between the same sizes as the quartz, both by the authors' method and the work index equation, are listed. According to the authors kw-hrperton = 259/(16.1)".

Jan 1, 1961

Lead-zinc production in Canada accounted for 19% of the total value of metals and minerals produced in 1976, says Keith C. Hendrick, president of Noranda Sides Corp. Mine production of recoverable zinc w as 1. 158 million toils of 27.4% of free world production in 1976. Slab zinc pro¬duction was placed at 472,000 tons that year. Canadian mine production of recoverable lead was 247,000 tons or 10.6% of the free world production. Refined lead that year was at 177,000 tons.

Jan 11, 1977

By D. W. McGlashan, K. N. Mcleod

IN the use of free bubbles with precise temperature control and continuous pH measurement, the contact angle apparatus differs from all previous equipment. Experimental procedures differ sharply from the captive bubble method1,2 of introducing the gaseous phase in the three-phase system. When freed from the tube and captured by a solid surface, a bubble more closely conforms to the spherical ideal set up by the usual mathematical analysis of surface free energy or surface tensional relationships of the forces involved. The assembled equipment, Fig. 1, departs from the usual contact angle apparatus in providing: 1) water circulation for fixing temperature, 2) instruments to measure and record pH during testing, and 3) a system for producing and using free bubbles. The apparatus allows testing over a broad range of closely controlled conditions, and the use of free bubbles gives contact angles independent of operator manipulation, which was unavoidable in the older captive bubble method. A bubble released below the specimen rises through the liquid and contacts the mineral. If the mineral is gas-avid the bubble adheres, developing a finite contact angle. Reaction cells (1), 2x33/8x5 3/16 in. ID, are of pyrex glass 5 mm thick. To prevent optical distortion, the sides are optical flats and are planed parallel to within five wave lengths of light over the entire surface. Special cement is required to withstand chemical attack and thermal shock. The cell is placed in a thermal jacket (2) made of welded aluminum. A water seal for the optical ports is made by using O-rings tightened against the flats of the cell by fine-threaded and adjustable ports, Fig. 2. In-flow water is discharged downward from a manifold located near the bottom of the cell jacket. Water overflows the weirs at each end of the cell jacket, discharging from both sides to a collecting manifold (24). A hose (26) leads the overflow water to the thermal-conditioner well (4), which is recessed to accommodate a reaction cell and two beakers (150 ml). Both the thermal jacket and the thermal-conditioner well are insulated to minimize the effects of temperature differentials. Water, discharging from the thermal-conditioner well, returns to a thermostat bath and pump (3), from which it is pumped to the thermal jacket. The thermostat bath permits temperatures to be adjusted from 1" or 2°C to 80°C and will maintain the selected temperature within 0.2ºC. An electrode support (22) groups the four electrodes (8) so that they fit conveniently into the reaction cell, Fig. 2. This assembly holds the glass electrode, the calomel electrode, the temperature-

Jan 1, 1957

An ore search for commercial titanium-bearing ore deposits is in progress by the Crane Co., manufacturers of valves, because they expect this metal to be important in valve manufacturing in the future. The company will eventually be mining and making titanium sponge. At present they are buying titanium tetrachloride from the Stauffer Chemical Co, at Niagara Falls and making titanium by reaction with magnesium. Production from the Babbitt concentrator of Reserve Mining Co. is scheduled to begin in late 1951 or early 1952. The capacity is to be 300,000 tons of pellets per year made from magnetic taconite concentrates.

Jan 7, 1951

By R. W. Newcomb

THE constancy of calibration, and to a great extent the life, of a thermoelement is dependent on the suitability of the primary protecting tube in which the wires are mounted, particularly when used at high temperatures. An ideal thermocouple protecting tube would be com-posed of materials that would not contaminate the thermoelement wires contained in it-one that would remain absolutely gas-tight ,it all temperatures of usage, that will not be attacked by gases, or other surrounding agencies, that is not destroyed by heat, that withstands sudden and extreme temperature changes, that affords a high degree of mechanical protection and does not deform at high temperatures, that is a good heat conductor and obtainable in small diameters so as to keep down lag factors. It has not yet been possible to produce tubes of any known mate-rials that will meet all of these conditions. In selecting protecting tubes, therefore, one should be chosen the characteristics of which best fit it to the particular conditions of usage. Frequently conditions are such that two tubes have to be used, a primary gas-tight protecting tube inside of a secondary protecting tube, because certain agencies will attack the primary gas-tight tube unless it is guarded by the outside tube.

Jan 9, 1919

By Richard F. Link, George S. Koch

About 50,000 assays of mine samples were required in a preliminary investigation of the distribution of gold, silver, lead, copper, and zinc in two large Mexican mines, the Frisco mine at San Francisco del Oro (Chihuahua) and the Fresnillo mine at Fresnillo (Zacatecas). The feasibility of working with so many assays rests directly on the use of machine processing methods. The purpose of this article is to describe the methods used because machine (or data) processing can also be used efficiently to make the many calculations from mine assays needed in mining operations. No particular originality is claimed for these methods, which are straightforward applications of standard procedures for machine processing. Inasmuch as machine processing is essentially a routine job once it is begun, procedures must be organized more completely than is the case where human judgment can be inserted at every step. Before undertaking any work, it is necessary to decide carefully just which data must be processed as well as the exact results desired.

Jan 9, 1960

By M. M. Neale

The pottery department has been aptly described as the "heart of the zinc plant," md every operator of a horizontal-retort plant is acquainted with the fact that good retort practice is the keystone of the smelting process. Since retorts and condensers are clay products, it is obvious that improvements in other branches of the ceramic industry should be observed for possible adoption in the pottery process for zinc smelting. Deaeration of clay bodies is one of the improvements that have become fully, established in many brick and pottery plants. Our investigation of a number of these installations always yielded the same answer—improved practice. Improvement in workability, elimination of laminations, less porosity, greater wet and dry strength, were among the claims put forth for this process. All of these features are exceedingly desirable characteristics in the manufacture of a zinc retort. A preliminary test, which involved truck transportation of deaired slugs over a relatively long distance, did show the value of many of these characteristics in forming the retort. Results from the standpoint of , longer retort life in the smelting furnace were not outstanding. The idea lay dormant for several years but was revived again in 1940, when it was decided to make whatever changes were necessary in the equipment for pottery manufacture to fully demonstrate the process. A number of the manu- facturers of machinery for clay work were asked to submit proposals, and the plan finally adopted was extremely simple and economical. Machine FOR DeaeRRATING Selection of the ''Straight-line'' principle for conversion of the "Wettengel" pug mill to a ''vacuum-extrusion" machine preserved some usable parts of the original equipment, such as the drive mechanism, and main shaft. The converted machine consists of a feed hopper, a compression and shredding zone, a vacuum chamber, and an extrusion barrel, as shown in Fig. I. In operation the clay mix travels from the feed hopper into the compression zone, where it is compressed and finally forced around the tapered cone into the vacuum chamber. As it enters this chamber the clay body is shredded into thin plates, for exFosure to the vacuum. The shredder consists of a hub mounted on the main shaft, to which are bolted segmental sections, each of which carries shredder knives. The compression zone and extrusion barrel function as seals for the vacuum chamber and the shredded clay mix is agitated thoroughly during its exposure to the vacuum. A vacuum pump, equipped with a 3-hp. motor, is attached to this chamber, and maintains 25 to 26 in. vacuum during operation of the mill. Changes in Practice Prior to the adoption of the deaeration process, our standard pottery practice called for double mixing in the combination 7

Jan 1, 1944

By C. R. Knopp

Gas-oil relative permeability ratio is an important relationship in oil reservoir predictive calculations. A correlation has been developed from 107 gas-flood k/k tests on Venezuelan core samples. The correlating parameter is based on restored-state water saturation tests and' is applicable to both consolidated and poorly consolidated sandstone reservoirs. Data of the correlation show that there are no distinguishah1e differences between the mass-data groupings for the two c1assifications A procedure is recommended for running .sufficient relative. permeability analyses to compute a geometric mean of the sample group. The geometric mean is more representative of the total core, and probably the entire reservoir. For example, while only one in four of the k,,/k,., test curves agreed closely with the resultant correlation of this report, the geometric mean curves of the 16 suites (three samples or more). showed good agreetment ill three cases out of four. INTRODUCTION The gas-oil relative permeability ratio is an important, fundamental relationship in most oil reservoir predictive calculations. Predictive calculations are made to estimate future reservoir production characteristics and ultimate oil recovery. The k1,/k2, relationship is specifically needed to relate the surface gas-oil ratio to the reservoir oil and gas saturation, and to calculate the relative movement of these phases within the reservoir whenever some of the more complex driving mechanisms are present. Laboratory k1/k2, tests are not generally run as a routine analysis. Consequently, k1/k2 data often are not available when needed because the cost of laboratory work could not be justified or the need for such data had not been properly anticipated. When laboratory k1/k2, data are available, they are often very difficult to interpret. For example, wide divergence is sometimes shown in a family of k1,/k1, tests representative of the producing horizon in a single well. With these considerations in mind, a study was made to determine if a relationship might exist between the k1,/k2, curve and some other simple laboratory test criteria. The most probable k1/k2, curve correlation for Venezuela described in this paper is the result of the investigation. The presented correlation defines the most probable gas-flood k,,/k,, curve through the medium of air-water capillary displacement and centrifuge water saturation tests. The laboratory procedures of these tests are. relatively simple, and inexpensive; test data should be. widely available- from routine analysis. DATA AVAILABLE, LABORATORY METHODS The report correlation utilized 107 gas-Hood k1/k2, tests run on sandstone cores of Venezuelan reservoirs. Table 1 is a general tabulation of data pertinent to the tests, while Table 2 summarizes the data. Thetests include 96 from Western Venezuela and 11 from Eastern Venezuela. Eighty-two- of the 107 test samples were sandstones that varied from poorly consolidated to-unconsolidated; 25 were consolidated. The average sample porosity was 26.7 per cent and the average permeability was 1,121 md; these values typify the better sandstone reservoirs of' Venezuela. The Welge gas-flood technique,' based on fundamental Buckley-Leverett frontal displacement theory, was introduced in about 1952 and is widely accepted in the industry. The laboratory procedure is relatively simple, rapid, and can be performed on small core samples. While there have been some minor variations in sample preparation and laboratory procedure in the tests used for the correlation, these tests can be generally summarized as follows. The core sample was first sol vent-extracted and dried. Connate-water saturation was restored by the oil-flushing or evaporation-blow down methods. At the beginning of gas flood the hydrocarbon pore volume was completeiy saturated with the test oil phase. Unsteady-state gas-oil displacement then began with the injection of nitrogen or helium. while the displaced oil and gas phases were incrementally metered at the out-flow face. From the test data, the k,,/k,, curve was calculated by the Welge method.' The individual oil and gas relative permeabilities were also calculated." CORRELATING PROCEDURES In attempting to establish a basis of correlation, we found that broad mid-range sections of 105 of the 107 k,,/k,, test curves could be closely duplicated by a straight line. Only two curves did not show a degree of linearity in this region. Correlation-curve definition parameters were subsequently developed from this observation of consistent mid-range linearity. Possible correlating variables were limited to the physical properties measured on core samples that (1) were widely available as common test data and (2) could be easily and cheaply obtained through future laboratory work. The more obvious possibilities were porosity, permeability and

Jan 1, 1966

By P. R. Sperry

In an investigation of the decomposition of the solid solution in a cold worked high-purity aluminum alloy containing 7 pct Mg, aged at temperatures from 30o to 82°C, the nucleating sites at the earliest stages of precipitation were observed to be of two types. Nucleation occurred at the high angle grain boundaries both when the alloy was initially cold worked and when solution annealed. Nucleation also occurred at certain unique deformation markings which began to appear in abundance at approximately 30 pct reduction in thickness by cold rolling. These deformation markings were identified as deformation (kink) bands rather than as the usually assumed "slip planes." Zn material that was cold rolled 15 pct, only the grain boundary Fig. 2—A1-7 pct Mg alloy, cold worked 60 pct and heated at 230° C for 5 min. Etched with Perryman's reagent. X500. Reduced approximately 25 pct for reproduction. (a) Bright field illumination, precipitate deeply pitted. (b) Phase contrast, showing slip markings.

Jan 1, 1962

By P. G. Winchell, J. K. Jackson

The strtcture of body-centered Fe-Ni-C alloys (0 to 16.5 wt pct Ni) containing less than 0.015 wt pct C was investigated by measuring the carbon-diffusion peak at low frequencies with a torsion pendulurrr. By determining the Snoek damping in ferrite and in quenched alloys of identical composition, the effects of nickel content and heat treatment were separated, and the existence of a structure in which Snoek damping is greatly reduced was revealed in the quenched ternary alloys. The relative amount of this structure increases with increased nickel content and cooling rate. It is proposed that this structure may be highly imperfect or tetragonal. In Fe-Ni-C alloys containing only ferrite the addition of nickel (0 to 5.1 wt pet) decreases tke area of the carbon-diffusion peak and shifts its position to lower temperatures but broadens the peak only slightljl. The decrease in peak area with increasing nickel implies that short-range interactions with the nickel atoms prevent some of the carbon atoms from participating in the relaxation process. The shift in the peak position indicates a long-range effect of nickel on the movement of carbon atoms so that at 300°K the diffisivity of carbon in -ferrite is increased by about 35 pct by the addition of 5.1 tut pct Ni. The results are presented as distributions of relaxation strength 072 the activation energy under the assumption that the frequency factor is invariant. BODY-CENTERED iron-base solid solutions dissolve carbon interstitially in the octahedral sites. The occupation of an octahedral site produces a tetragonal distortion of the surrounding lattice. These sites fall into three sets according to the orientation of the tegragonal distortion associated with each and may be identified by their lattice coordinates as: type 1/2 0 0, type 0 1/2 0, type 0 0 1/2. At low carbon levels in cubic ferrite the carbon atoms are distributed at random1 among these sites. In high-carbon body-centered iron-base solid solutions, which are unstable with respect to several two-phase mixtures, a tetragonal structure occurs as the product of the diffusionless transformation of austenite. This transformation is commonly accompanied by appreciable microstrain and its product is called martensite. The tetragonality of martensite, a supersaturated solution of carbon in a iron, is maintained prior to decomposition even though local diffusion of carbon occurs as evidenced by carbide precipitation. The tetragonality is taken as evidence that one set of octahedral sites is preferentially occupied by carbon. (This preferential occupation is called ordering below.) Support for this view is presented by the absence of strain-induced carbon-atom diffusion in high-carbon solid solutions (martensite). Such diffusion occurs in ferrite and produces the 40°C internal-friction peak observed at 1 cps frequencies.' Thus, there appears to be qualitative evidence favoring the view that at sufficiently high carbon levels tetragonality arises spontaneously as a result of the ordering of the carbon atoms; however, no experimental evidence exists concerning an equilibrium between cubic and tetragonal body-centered solid solutions. Moreover, attempts to estimate the energy of ordering7-' predict a value too low to maintain the tetragonality observed at medium carbon levels, 0.3 to 0.6 wt pct C. In the present work an attempt using internal-friction measurements is made to establish the presence or absence of tetragonality in low-carbon body-centered solid solutions formed by quenching austenite. Fe-Ni alloys containing about 0.01 wt pct and 0 to 15 wt pct Ni were selected for the study. While the work was in progress Gilbert and Owen10 reported that the transformation which occurs in these alloys during quenching at rates up to 5000°C per sec is not martensitic but is more properly categorized as massive. Thus, the solid solution

Jan 1, 1964