Search Documents

By W. A. Ver Wiebe

Spurred on by the very high demands for new crude supplies resulting from World War 11, the oil men of Kansas strained every effort in 1943 to find as many new pools as possible. In all, 1761 test wells were drilled, ,of which 895 were successful in finding new oil supplies and 32 in finding new gas supplies. The total number of wildcat wells drilled in Kansas was 577, including the so-called "extension wildcats," which are located less than 2 miles from production. As a result of the very determined effort to find new oil reserves, 49 of the wildcat test wells found new oil pools in western Kansas and 7 found new oil pools in eastern Kansas. There were 289 rank wildcat tests, and among these 28 were successful ventures. They are responsible for 26 of the new oil pools recorded for the year and 2 of the new gas pools recorded. The ratio of dry holes to producing wells among such rank wildcats is thus approximately 10 to I (289 dry and 28 good). This compares with a ratio of II: I in 1942 and 6:1 in 1941; the same in 1940 and 5:Iin 1939. With nearly all wells flowing to their maximum economic capacity, the total production for Kansas during 1943 reached a new high; that is, 107,700,000 bbl., compared with 97,000,000 during the previous year. Similarly, the amount of gas sold during 1943 made a new high point on the production curve. The total amount was 122 billion cubic feet, compared with about 98 1/2 billion cubic feet for the year previous. As usual, the large Hugoton field of south- western Kansas accounted for approximately half of the total gas production. Highlights of the Year Despite the fact that 56 new pools were found in Kansas during 1943, it must be admitted that the future reserves of the state have not been increased greatly. Most of the new pools seem to be of minor value, although it is admittedly impossible to gauge the future production of any pool in Kansas with any exactitude. Judging by the later performance of some of the pools found in 1942 and in 1941, less than five of the new pools are likely to make any great contribution to the state's future oil reserves. Taking up the counties of Kansas in alphabetical order, the following statements summarize the highlights of the year. In Graham County, the Morel pool was extended to the southeast and this pool now promises to become one of the important pools of western Kansas. Several of the older wells have already contributed more than I000,000 bbl. of oil, and such a figure is considered very satisfactory in Kansas. In McPherson County, important new reserves were found by persistent drilling in township 17 S., R. I. W., the most northeastern township of the county. Many new wells in older pools and discovery wells in new pools make this region look promising. The Lindsborg pool, which had a sensational revival during 1942, was also extended in a number of directions and has now become a rather large producing area with a fairly high future potential capacity.

Jan 1, 1944

By C. S. Yust, Lida K. Barrett

The change in shape of the void in a sirzterir~g copper mass has been investigated as a juntction of' density. A serial sectioning' technique was used to eoaltrate the irregular shape of the void at two levels qf density. A measure of the void size and configuration, the proximity number, is defined and used to describe the progress of void removal. The process of. void removal deduced front the observations of this study contrasts with current sintering models in that it takes into account the irregularity of structure of a sintering mass and demonstrates that isolated Porosity does not occur first as spherical pores, but as large, definitely nonspherical sections of the void void volume. The process of sintering, about which there is much practical and theoretical knowledge, has evaded a direct and thorough analysis despite the intensity with which it has been studied for 60 years or so. This is due, of course, to the complex structure of a sintering mass and the inability to observe directly the development of a fully dense solid from the initial particulate arrangement. Extensive theoretical analyses have been based on the adoption of one or another of several model systems, that is, by visualization and analysis of some sort of regular assembly or arrangement of geometric "particles" approximating the conditions of a sintering mass. It seems appropriate at this time to try to examine experimentally in some detail the extent to which a sintering mass of irregular particles dlffers from these models. Many models deal with neck growth and the initial stage of sintering and follow the direction established by ~ucz~nski' in 1949 for the sintering of spheres to flat plates. Recently Johnson and cutler2 have adapted these models to sintering of powder masses. coble3 has presented a mathematical model for sintering that applies to the middle and final stages of the process. These papers, without exception, assume a regular geometry, generally spheres in contact in a regular array. Rhines~ and coworkers, however, are studying the sintering process by applying a model based on the topological concept of genus which permits them to consider an irregular structure. whites has described the various models with the exception of that of Rhines et al., and the assumptions on which they are based and their shortcomings. The present paper examines the geometric changes that occur in the powder mass during sintering by examination of the void. The method is to analyze a series of partially sintered structures and to propose from this analysis the sequence of events which occur in the removal of the void space as a sintering mass progresses from a collection of individual particles to a solid body. The irregular nature of the stacking of particles and of the particles themselves will be taken into account. The significant points derived from this study are: first, accurate reconstructions of the irregular void shapes are presented; second, it is clearly established that closed porosity occurs first as widespread volumes of interconnected porosity, definitely nonspherical in shape; and third, a new factor, the proximity number, is defined, which serves in this paper as a tool for describing the void shape changes observed, and which will be used in a later paper as part of the basis of a mathematical model for sintering. While the specific material studied is copper, the observations are thought to be relatively general as indicated by comparison of the results with partially sintered structures in other materials presented in the literature, both metallic and nonmetallic. EXPERIMENTAL PROCEDURE Four series of specimens representing progressive stages of the sintering process were prepared by sintering high-purity copper powder for various time periods. A relatively large particle size was used so that the void-solid interface could be readily distinguished at low magnification. In three series of specimens a loose stacking of particles was obtained by pouring powder into an alumina mold and lightly tapping the mold. The green density of such compacts was approximately 40 pct of theoretical density. Two of these three series utilized irregularly shaped particles in the size range -230 +325 mesh, one series sintered in vacuum and one in hydrogen at 950°C. The third series of loosely stacked particles consisted of spherical particles in the size range -270 +325 mesh, sintered in hydrogen at 950°C. A fourth series was prepared from compacted irregular particles sintered in hydrogen at 950°C. The specimens for this series were formed by lightly pressing the irregularly shaped particles in a steel die; the green density of the pressed pellets was approximately 60 pct. The irregularly shaped particles used in this study are shown in Fig. 1. The density of these particles, measured by a toluene picnometer technique, is 98.2 pct of theoretical density. Each particle is highly convoluted, and in some instances appears in cross section to contain internal porosity. The density measurement, however, indicates that completely enclosed porosity is very small so that the individual particles have a highly irregular surface but are essentially fully dense copper. Therefore, most of the void space that appears in two dimensions to be isolated within the particle is actually at the particle surface and connected to the external void in the dimension not included in the plane of the cross section. The void space that appears as void surrounded by the par -ticle or within folds in the particle w~ll be r~fc\r?

Jan 1, 1968

By Chikao Nishiwaki

INTRODUCTION The Japanese dependency for mineral raw materials from foreign sources increased rapidly within the 20 years since the Korean war. During this 20 year period Japan has attempted to industrialize and develop her economy while depending mostly on heavy import of nearly all kinds of mineral raw materials. She has fabricated them using energy generated mostly by mineral fuel that are also imported. Fabricated goods are either used domestically to accelerate more fabrication industry or exported after adding more refinement or fabrication. In this paper iron ore as a major raw material for the Iron and Steel industry, three major base metals, copper, zinc and lead, and petroleum as a major energy source have been selected as examples to represent the general features of various kinds of mineral raw materials that are imported. Among other important mineral commodities for which Japan dependa upon foreign sources are: Aluminium, nickel and cobalt, potash and phosphorous 100 percent dependent and tin, tungusten, chromium and molybdenum over 95 percent dependent. IRON ORE Statistics for the important iron and steel raw materials, namely iron ore, coal and scrap iron are shown in Tables 1, 2 and Fig. 1. Iron ore is by far the most important and basic among these three commodities. There has been practically no steel or iron imported as a metal into Japan during this period. Iron ore, including aggregate such as pellets, and metallurgical coal are mostly transported in large ore cargo boats to the port where very efficient port facilities unload them directly at the steel mill site. As a result

Jan 1, 1976

By C. A. Herbert, C. M. Young

WithIn the past few years, considerable development has been made in the coal-mining industry in Illinois and Indiana and it is the purpose of the authors to record its most important phases. Perhaps the two most striking features are the entry into the producing fields of certain large consumers of coal and the magnitude of some of the new operations. Mines are now being equipped by the Chicago & Northwestern R. R., the Chicago, Burlington & Quincy R. R., the Standard Oil Co., of Indiana, and the Union Electric Light & Power Co. of St. Louis. Besides, the U. S. Steel Corpn. has increased its coal-mining activities by commencing operations on its large holdings northeast of Benton, Franklin CO., Ill. Until recent years, the supply of coal has commonly been adequate and prices have generally been favorable, especially to large consumers, as the magnitude of their purchases enabled them to obtain satisfactory quotations from producers. In fact, most consumers of coal have believed that they could buy their fuel more satisfactorily in the open market than they could produce it themselves. The entry of the United States into the war was accompanied by various disarrangements of industrial conditions, and a demand for coal in excess of the supply seemed likely to be experienced for an indefinite period. Under these circumstances it seemed that the greatest assurance of a supply of fuel was its production by the operation of mines. In the case of the Chicago & Northwestern R. R. and the U. S. Steel Corpn. the production of coal has been carried on for many years with satisfactory results, but the C. B. & Q. R. R., the Union Electric Light & Power Co. and the Standard Oil Co. of Indiana had not been producers of coal, at least in this district. Apparently the most impressive feature of the newest mines is their capacity, for in some cases it is planned that production shall be in the neighborhood of 1000 tons per hr. There are mines now in this field having nearly that output, but these were not planned for such output; in fact, when the shafts were sunk and the machinery installed it was generally supposed that the daily outputs would be only in the neighborhood of 4000 to 5000 tons. Incidentally, there has risen

Jan 1, 1920

By P. A. Flinn

ALTHOUGH many physical properties of superlat-tices have been studied intensively, relatively little attention has been paid to their mechanical properties until recently. Even for the well-known transformation in 0 brass, the effect of the transformation on plastic behavior has only lately been extensively investigated.''' A partial analysis of dislocation structure in superlattices has been given by cottrel13 and his theory agrees well with the experimental results on CU3AU.4,5 His analysis, however, is implicitly limited to low-temperature effects, since it does not include the behavior of dislocations at temperatures high enough for diffusion, and hence climb, to occur. The work of Herman and Brown2 on the creep of 0 brass indicates that important effects occur under such conditions, and consequently, the theory should be extended to include them. Such high-temperature effects cannot be observed in Cu3Au, since it disorders below the temperature at which diffusion occurs at a reasonable rate. There are materials of the same structure, however, such as Ni3A1, which retain their order up to, or close to, the melting point. GEOMETRY OF THE COMMON SUPERLATTICES The two best-known ordered structures are the 0 brass type, B2, shown in Fig. 1, and the Cu3Au type, Ll2, shown in Fig. 2. In the B2 structure the (000) and (1/2, 1/2, 1/2) sites are different in that they are occupied by different types of atoms. The symmetry of the structure is then lowered from a body-centered cubic, A2, in which the sites are equivalent, with atoms located randomly in the sites, to simple cubic. This lowering of symmetry has the consequence that two types of regions may occur within a crystal: regions where A atoms are in the (0, 0, 0) sites, and regions where they are in (1/2, 1/2, 1/2) sites. The boundary between two such regions will contain bonds between like atoms, and be a surface of higher energy. These regions are known as antiphase domains and the boundary as antiphase boundary. In the B2 structure, boundary formed during the ordering process should disappear as a result of domain growth, since any domain growing to the boundary of two others will join one and engulf the other.' In any well annealed crystal, only a single domain should exist, with antiphase boundary present only in connection with dislocations, as discussed below. The L1, structure is related to the A1 (face-centered cubic) in much the same way as the B2 is to the A2. The face-center sites are occupied by A atoms, and the corner sites by B atoms. The symmetry is again lowered to simple cubic, and antiphase domains can exist. In this case, however, there are four initially equivalent sites in the unit cell: (0,0,0), (0, 1/2, 1/2), (1/2,0, 1/2) and (1/2, 1/2, 0). In the ordered structure any one may be occupied by a B atom and the other three by A atoms. Thus four types of antiphase domains can occur in this structure. This is sufficient to permit a metastable "foam structure" to exist within a crystal.''7 Antiphase boundaries along three different planes are shown in Figs. 3, 4, and 5.* *The presence of a layer of disordered material between antiphase domains, as suggested by Jones and Sykes8 does not seem likely. Such a layer would be a region of unnecessarily high energy which could readily be reduced by the formation of the type of boundary discussed here.__________________________________________________________ The notation (111) [110] means a boundary lying along a (111) plane between antiphase regions related by a 1/2 [I10] translation. It may be seen in Figs. 3 and 4 that an antiphase boundary usually results in incorrect nearest neighbors (shown connected by braces). However, as pointed out by Wilson, a boundary of the (001) [I101 type can exist

Jan 1, 1961

By T. S. Lundy, J. I. Federer

Chemically purified Zr95and Cb95 have been used in determining self-diffusion coefficients in the bcc phase of iodide zirconium over the temperature range of 900o to 1750°C. The temperature dependence of the diffusion coefficients could not be described by the usual Arrhenius-type equation over the entire temperature range. Values of the apparent frequency factors (D0)a and activation energies (Q)A for ZR95 varied from 4.8 x 10-6 to 2.5 x 10-2 sq cm per sec and 20,700 to 46,900 cal per mole, respectively, between 900°and 1750°C. Similarly, for Cb95, values of (Do) a and (Q)A varied from about 2.4 x 10'5 to 0.25 sq cm per sec and 26,500 to 56,800 cal per mole, respectively. The data may be described in terms of the a to ß transition temperature of 1136 °K and the absolute temperature of the diffusion anneals by the following eauations: SEVERAL studies on the diffusion of Zr95 in zirconium have been reported.1"5 The values of the constants contained in the usual Arrhenius-type equation for describing the temperature dependence of the diffusion coefficient, D = Do exp [- Q/(RT)], are summarized in Table I. The reported values of Do, the frequency factor, and Q, the activation energy, are seen to vary by factors of about 60 and 1.6, respectively. Examination of the data from any one study indicated reasonable consistency of measurements. The large discrepancies of over-all results, therefore, cannot be explained on the basis of experimental scatter. One possible explanation for the differences in results could be a varying impurity content of the zirconium. Another possibility is that the radioactive daughter, Cb95, influenced the values of some of the determined diffusion coefficients. Therefore, the first of the three purposes of this study was to reconcile the large differences in diffusion results that have been obtained. Several empirical relations have been proposed to relate the diffusion coefficients in solids with physical properties, such as the absolute melting point, the heat of fusion, and the heat of sublimation.

Jan 1, 1963

By William P. Blake

(Canal Zone Meeting, November, 1910.) A DEPOSIT of manganese-ore near Tucson, Ariz., merits notice by reason of the peculiar form in which it occurs, and as a striking. example of ore-deposition by vadose upward capillary flow of metal-bearing solutions with concentration at the surface of the country-rock. This deposit occurs at the northern end of the Coyote mountains, about 40 miles west of Tucson, upon the outcropping beds of porphyritic rock, which appear to be partly-metamorphosed strata of volcanic tufa, probably of late Secondary or of Tertiary age. The strata dip northward at a low angle, and present a series of basset-edges in parallel lines of outcrop, east and west, facing the south and extending over many acres. Successive groups of these outcrops, from 5 to 20 ft. in breadth, are coated with oxides of manganese in lustrous black films and crusts, shining in the sunlight like polished ebony, and covering the whole surface of the rock above the soil. Seen at a little distance, these croppings look like solid ledges of massive and pure ore; but closer inspection and a few blows of the hammer reveal their true nature as a superficial coating allied in origin to the blackened shining surface of rocks exposed in desert-regions, familiarly known as " desert paint" or "desert varnish,"' similar to the phenomena described by me in a former paper, but much thicker and heavier. * By reason of the death of the distinguished author, this communication, probably his last communication to technical literature, is published without revision of the proofs by him. A term first given y G. K. Gilbert. See Rocks, Rock-Weathering, and Soil; by George P. Merrill, p. 256 (New York, 1897). Superficial Blackening and Discoloration of Rocks, Especially in Desert Regions, Trans., xxxv., 371 (1905).

Sep 1, 1910

By A. A. Bauer, H. A. Saller, F. A. Rough, J. R. Doig

among uranium alloy systems are the U-Zr, U-Ti,and U-Mo binary systems, in that an intermediate phase, of limited solubility range, exists in each system. These intermediate phase alloys offer a promising field of investigation, both as binary alloys and as ternary alloy combinations. While a limited amount of work has been done on the binary alloys, none has been done on ternary combinations of these alloys. As a possible prelude to more intensive investigation of these systems, a study of the phase relationships between the 6 phases of the U-Zr and U-Ti systems was undertaken. The solid-state portions of the binary constitutional diagrams for the U-Ti,1 Zr-Ti,2 and U-Zr3 systems are shown in Fig. 1. The solid to liquid transformations are not shown, as these transformations were not studied in the ternary system. The phase designations employed are based upon those shown in the uranium constitutional diagrams. The crystal structures of the various phases are given in Table I. Experimental Materials and Methods The ternary section presented is based upon the results of thermal, metallographic, and X-ray analyses of a series of alloys ranging in composition between the phases of the U-Zr and U-Ti systems (U-74 atomic pct Zr to U-35 atomic pct Ti). After preparation of the alloys, thermal data were obtained. On the basis of these data, specimens were heat treated and examined metallographically. Specimens were then selected from those heat treated for X-ray determination of the phases present in what were considered critical phase regions. Alloy and Specimen Preparation—Alloys for this investigation were prepared from selected as-reduced uranium and crystal-bar zirconium and titanium. For nominal compositions, see Table 11. Charges were arc melted from five to seven times under a helium atmosphere, finally being cast into wire-bar form for fabrication. A zirconium getter button was used to clean the furnace atmosphere prior to melting. The alloys were homogenized 20 hr at 900 °C and furnace cooled. A portion of each bar was then removed for thermal analysis; the remainder was saved for fabrication. Alloys 8 through 14 were placed in steel tubes along with zirconium getter chips and, after flushing with argon, the tubes were welded shut and rolled at 1500 °F to a 50 pct reduction in diam. The remaining alloys were annealed 24 hr at ll00°F to insure transformation of the ? phase to the 8-U2Ti phase and were then hot rolled from a salt bath. Attempts to roll alloys 6 and 7 at 1100 °F were unsuccessful. Following this, attempts were made to roll pieces of alloys 1 through 5, which had cracked rather severely during casting, at 1200 °F, but these efforts were also unsuccessful. These alloys were, therefore, further treated in their cast and homogenized condition. All alloys were pickled to remove oxide formed during rolling. Thermal data were obtained on these alloys by conventional differential thermal analysis at a heating rate of 30C per min, and by a high-speed heating method at rates of approximately 10°C per sec. For the latter method of analysis, a 36-gage Chromel-Alumel thermocouple is spot welded between two slivers of alloy, the sandwich being en-

Jan 1, 1958

By John V. Beall

There is an underlying surge to mining in the Philippines." So said A. R. "Ham" Reed, general manager Itogon-Suyoc Mines, Inc., to this reporter last November. Itogon-Suyoc is a small company with a struggling gold mine, a mixed sulfide mine and some prospects. In the Republic of Philippines (ROP), politics, which have an effect on mining, create some uncertainties. By July 1974, no mining company may have more than 40% foreign ownership. The ownership provision is a matter of concern to such important companies as Atlas and Benguet Consolidated and is generally considered a deterrent to new foreign investment. Under these circumstances, Reed's comments are of interest. On foreign prospectors: Don't come in cold; find a Philippine partner or buy into a company already here. Physical conditions of exploration are tough-terrain, communications -but the mineral potential is excellent.

Jan 4, 1969

By A. T. Aldred

HIS note reports the existence of several new scandium intermetallic compounds of the A2B and AB stoichiometries where the A element is scandium and the B element is from group VIII or IB of the periodic table. Alloys were arc melted from high-purity materials using 2-g charges. Typical lot analyses for the materials used are given in Table I. Chemical analyses were not made on the alloys as there was little or no weight loss on melting. After annealing the specimens for 14 days at 600°C and water quenching, metallographic and X-ray techniques were used to determine the occurrence of the various phases. Table II lists the relevant data for the A2B phases. The Ti2Ni structure,2 has ninety-six atoms in a face-centered cubic cell, whilst the Al2Cu structure is body-centered tetragonal.3 The occurrence and stability of the various A2B type phases in transition metal alloy systems has recently been considered by Nevitt.4 The Ti2 Ni-type phases occur over a relatively narrow range of radius ratios from 1.14-1.26 with A partners mainly from the titanium group and B partners predominantly from the cobalt group. This suggests that both a favorable relative size of the atoms and a favorable electron concentration are necessary conditions for the existence of this structure type. A12Cu-type phases involving Ti group elements as A partners are formed with B partners from the cobalt and nickel groups, predominantly the latter, and have a higher radius ratio (1.27-1.29) than the Ti2Ni-type phases. The occurrence of both Sc2Pd and Sc2Co can be rationalized in terms of these considerations but SczNi is anomalous because of its high radius ratio. The radius ratios are calculated from the Goldschmidt CN12 radii and it might be postulated that the scandium atom is reduced in size in the compound. Unfortunately the apparent atomic size of scandium in the compound cannot be calculated from a knowledge of the structure and lattice dimensions. The crystal structure of the Sc2Au compound could not be identified from the powder diffraction pattern, but it is interesting to note that it is isostructural with a series of A2Au phases where A is a rare earth element.5 Pertinent information concerning the AB phases found in this investigation is given in Table 111. All the phases have the ordered bcc CsCl structure. The occurrence and stability of CsC1-type phases have recently been discussed by Dwight,7 who concludes that the relative sizes of the atoms do not appear to be a controlling factor (the radius ratios of all the known phases vary between 0.985 and 1.439) but that the occurrence of the phase is predominantly dependent on the relative positions of the A and B partners in the periodic table. As a measure of the stability of a given CsCl phase it has been customary to define a lattice contraction on alloying, DAB — dAB, where DAB is the AB interatomic spacing as calculated from the Goldschmidt CN8 radii and dAB is the AB interatomic distance in the compound (= v3/2 ao). Values of the parameter DscB -dScB for the compounds found in this investigation are given in column 5 of Table III and are plotted in Fig. 1. If the lattice contraction does in fact reflect the stability of a phase then Fig. 1 shows two very interesting trends when the position of the B partner in the periodic table is considered. Firstly, within any given group the stability increases in order on going from the first to third long period. Secondly, within any given period the stability increases in order as the B partner is taken from the copper, nickel, and cobalt groups. In the case of the second long period, the lattice contraction reaches a maximum at ScRh and then decreases to ScRu. The same trend could

Jan 1, 1962

By Thomas T., Read

ANY discussion of State-supported schools of mining and A metallurgy needs to be prefaced by a definition, since the first school to offer a mining curriculum, the Pennsylvania Polytechnic College, was established by a grant from the State. But, so far as can be determined, it received no further State support. It would be tiresome to go into precise details,. and it will be enough to stipulate that by State schools are meant those which derive their main financial support from regular appropriations made by a State legislature. The University of Michigan was the first of these to offer a mineral industry curriculum; its story, as well as those of Wisconsin and Illinois, has been related in the preceding chapter.* Arranging the others in chronological order involves making a decision as to what weight to attach to plans for giving instruction, as contrasted with its , effective initiation. This may appropriately be illustrated by the history of mineral industry education in California. California Among those who came to California in 1849 and the following years were many New Englanders who had a keen interest in education. Some of them, mostly Congregationalists and Presbyterians, sought to establish a school of higher education around San Francisco Bay and eventually succeeded in opening the "Scientific and Classical School at Contra Costa' in Oakland, at Broadway and 5th St., on June 20, 1853. This prospered so well that it was chartered by the State as the "College of California" on April, 13, 1855. Developing so rapidly that its quarters became cramped, in 1864 it not only bought a tract of

Jan 1, 1941

By W. V. Bluck, W. L. McMorris

Higher coal quality is being recognized in potentially lowering the cost of power as measured at the bus bar. Assessment of potential coal supplies for most power plants is now going beyond buying at the lowest delivered fuel cost. It is now taking into consideration other factors, such as handling, storage, pulverization cost, boiler fouling, post combustion cleanup, and waste disposal costs. New measurements of quality are being considered now by those producing and those consuming the fuel by assessing numerous variables in the total fuel cycle to achieve the lowest possible power costs.

Jan 1, 1986

By Alec M. Crowell, J. W. Sanders

While the production of crude oil and condensate in South Arkansas increased only 1.7 per cent over the 1940 figure, complete utilization of gas produced with the oil and condensate, and heretofore wasted, was beginning to be evidenced. There were 26,229,264 bbl. of oil and condensate produced in South Arkansas during 1941, as against 25,790,380 bbl. for the year 1940. (Fig. I.) Since 1936, deep producing sands have been discovered in 18 fields and during that period only 40 per cent of the total state production has come from Upper Cretaceous formations while 60 per cent came from the Lower Cretaceous and Jurassic formations. The gas produced with crude oil and condensate from the latter formation contains large quantities of hydrogen sulphide, the maximum being 6900 grains per 100 cu. ft. in the Patton pool of Lafayette County. Gas Utilization During the latter part of 1940 and the early part of 1941, pilot plants were placed in operation to determine whether the hydrogen sulphide and deleterious material in South Arkansas gases could be removed economically. The Federal Government desired to build a large aluminum plant in the Ouachita Valley and was seeking cheap fuel for the generation of electricity. The fact that the gases were produced with appreciable quantities of crude oil and condensate made it available at a very low price, since the state's conservation law prohibits the flaring of any gas. As a result of these experiments the first large-scale unit for the processing of gases containing hydrogen sulphide was placed in operation on Sept. I, 1941. The plant is in the Magnolia oil field, Columbia County. It processes residue gas from the Shell Oil Company's gasoline plant in that field and also raw gas from the Village field, 6 miles east of the Magnolia field. The gas entering the desulphuri-zation unit is laden with approximately 1400 grains of hydrogen sulphide per 100 cu. ft. and is stripped to a content of 4 grains per 100 cu. ft. The capacity of the plant is 15 million cu. ft. of gas treated daily under a pressure of 160 lb. per sq. in. The cost of treatment, exclusive of depreciation, is appreciably less than I per 1000 cubic feet. Two other plants of much greater capacity have been announced and priorities have been granted, which should bring the total amount of gas treated to 150 million cu. ft. daily. The gas to be treated will have a maximum hydrogen sulphide content of 4500 grains per 100 cu. ft. and will be processed under a pressure of 600 lb. per sq. in. These developments are something entirely new in field practice for the industry. The fact that this heretofore wasted gas is available at very low cost has led to the location of some eight war industries within the state, in addition to the alu-minum plant. Recovery OF Sulphur The Susearch Corporation and the Southern Acid and Sulphur Co. placed in operation during 1941 pilot plants to de-

Jan 1, 1942

By Alec M. Crowell, J. W. Sanders

While the production of crude oil and condensate in South Arkansas increased only 1.7 per cent over the 1940 figure, complete utilization of gas produced with the oil and condensate, and heretofore wasted, was beginning to be evidenced. There were 26,229,264 bbl. of oil and condensate produced in South Arkansas during 1941, as against 25,790,380 bbl. for the year 1940. (Fig. I.) Since 1936, deep producing sands have been discovered in 18 fields and during that period only 40 per cent of the total state production has come from Upper Cretaceous formations while 60 per cent came from the Lower Cretaceous and Jurassic formations. The gas produced with crude oil and condensate from the latter formation contains large quantities of hydrogen sulphide, the maximum being 6900 grains per 100 cu. ft. in the Patton pool of Lafayette County. Gas Utilization During the latter part of 1940 and the early part of 1941, pilot plants were placed in operation to determine whether the hydrogen sulphide and deleterious material in South Arkansas gases could be removed economically. The Federal Government desired to build a large aluminum plant in the Ouachita Valley and was seeking cheap fuel for the generation of electricity. The fact that the gases were produced with appreciable quantities of crude oil and condensate made it available at a very low price, since the state's conservation law prohibits the flaring of any gas. As a result of these experiments the first large-scale unit for the processing of gases containing hydrogen sulphide was placed in operation on Sept. I, 1941. The plant is in the Magnolia oil field, Columbia County. It processes residue gas from the Shell Oil Company's gasoline plant in that field and also raw gas from the Village field, 6 miles east of the Magnolia field. The gas entering the desulphuri-zation unit is laden with approximately 1400 grains of hydrogen sulphide per 100 cu. ft. and is stripped to a content of 4 grains per 100 cu. ft. The capacity of the plant is 15 million cu. ft. of gas treated daily under a pressure of 160 lb. per sq. in. The cost of treatment, exclusive of depreciation, is appreciably less than I per 1000 cubic feet. Two other plants of much greater capacity have been announced and priorities have been granted, which should bring the total amount of gas treated to 150 million cu. ft. daily. The gas to be treated will have a maximum hydrogen sulphide content of 4500 grains per 100 cu. ft. and will be processed under a pressure of 600 lb. per sq. in. These developments are something entirely new in field practice for the industry. The fact that this heretofore wasted gas is available at very low cost has led to the location of some eight war industries within the state, in addition to the alu-minum plant. Recovery OF Sulphur The Susearch Corporation and the Southern Acid and Sulphur Co. placed in operation during 1941 pilot plants to de-

Jan 1, 1942

By L. O. Howard

What was perhaps the first attempt at basic converting in the Southwest was made by the late Charles F. Shelby at Cananea early in 1907, when he removed the acid lining from one of the 8 by 12-ft. barrel-type converters then in use at the reduction works of the Cananea Consolidated Copper Co. and substituted a lining of one course of magnesite brick. In this shell, he blew 21 taps (about 180 tons) of matte to white metal before the brick gave out along the tuyhre line. In every case, the white metal so made was transferred and blown to copper in other converters. The cost of the lining was $700 and Mr. Shelby gave up the experiment as impracticable. No further serious effort to bessemerize copper mattes in a vessel having a more or less permanent lining of basic brick was made by any of the large copper smelters in the Southwest until some months after Messrs. Peirce and Smith had brought the question permanently before the public, and had proved it to be a metallurgical and financial success by their work at Baltimore and Garfield. Early in 1911, the Cananea Consolidated Copper Co. had in operation at its reduction works at Cananea, Mex., several 8 by 12-ft. barrel-type converters lined with magnesite brick which had previously been operating with acid linings. In the 18 months following, these converters produced 50,000 tons of copper. In June, 1912, this company installed the first of its new equipment of six stands of electrically operated 12-ft. Great Palls type converters, and shortly afterward discontinued the use of the smaller shells. In September, 1911, the Consolidated Kansas City Smelting & Refining Co. had installed at its El Paso plant two 10 by 26-ft. Peirce-Smith converters. Later, in March, 1913, one standard Great Falls type converter was added. About the time the Peirce-Smith converters were going in at El Paso, the Calumet & Arizona Mining Co. was experimenting with basic linings in 7-ft. by 10-ft. 6-in. barrel converters at its plant in Douglas, Ariz. These efforts were sufficiently successful to enable the plant to "handle the total output of copper in these small shells until the standard Great Falls converters were substituted in June, .1914.

Jan 1, 1917

By John A. Ames

Webster's dictionary nearly equates portland cement with its current primary definition of cement. While such equation may be a triumph of common usage, the confusion between the terms cement and concrete unfortunately is very widespread. Full definition of cement properly would extend to many substances, but for purposes of this chapter cement is restricted to "varieties" of portland cement including "portland-pozzolan" cement. Among the usually recited historical notes concerning cement is that it was developed by the Romans. Their use of cement in the great structures of Rome, and even in the far corners of their Empire, such as Hadrian's Wall in the north of England, testifies to the antiquity of a major cement industry. From English sources we know of John Smeaton's carefully proportioned hydraulic cement mixed in 1756 and of Joseph Aspdin's patented cement to which, in 1824, he gave the name portland cement. (He claimed that his cement mortar looked like the famous dimension limestone quarried from the Isle of Portland on England's south coast.) The year 1971 marked the centennial of portland cement manufacture in the United States. A fair historical account of the many real contributors to the cement industry between 1756 and 1972 unfortunately would be too extensive for this chapter. Development of rotary kiln practice and burning at higher temperatures clearly was the major move into today's technology. As part of the 4th edition of Industrial Minerals and Rocks, this chapter on utilization focuses on inferred interests of the anticipated readers. The main period for which statistics are cited generally is that since the 3rd edition (1960) of this same volume. Cement manufacture is the processing of selected and prepared mineral raw materials to produce the synthetic mineral mixture (clinker) that can be ground to a powder having the specified chemical composition and physical properties of cement. Cement making incorporates a number of distinct steps, but it is characterized by the key pyroprocessing (or "burning") step, which brings about the necessary changes in the raw materials. This pyro processing is a chemical process. Conversion of large volumes of mineral raw materials into specification-controlled cement at relatively low cost is the objective. Statistics on the cement industry are of uneven quality. The U.S. Bureau of Mines (USBM) is the principal collector of available data. These statistics can be only as good as the quality of information supplied by the reporting companies. The data perhaps most often questioned relate to productive capacity of the industry. The questions submitted by USBM are valid, nevertheless, and the information gained from them, as good as is available, is what is generally used. The Portland Cement Association also is a source of much quality information. The year 1972 witnessed a test of the adaptability of cement industry statistics. This was the year of conversion from barrels and sacks of cement as the units of measure to tons and hundredweights. The barrels and sacks related to volumetric measures in that a sack was judged to be 1 cu ft (weighing a "standard" 94 lb). A barrel was 4 sacks. Volumes of concrete are stated in cubic yards, and the number of cubic feet of cement in a cubic yard of concrete was a sensible approach to the mensuration involved. However, cements do not weigh the same amount from plant to plant or from type to type, and the buyer was more interested in getting an assured weight for his money than in "buying air." Thus, a sack, in accepted practice, became 94 lb instead of 1 cu ft, and a "barrel" became 376 lb, regard- less of whether it would fit into 4 cu ft of space. With the de facto dealing in weight rather than in volumes, the awkward numbers made little

Jan 1, 1975

By E. R. Gilbert

Klopp et al. have reported data on tensile and creep properties of are-melted and electron-beam-melted tungsten. We would like to point out some similarities between their creep results and ours on are-melted and powder-metallurgy tungstenand offer some alternate interpretations of the data which lead to different rate-controlling mechanisms. Klopp et al. observed extensive transient creep in the 2250" to 3500°F temperature range where the acthetivation energy is 106,400 ± 3300 cal mole-1. They suggest cross slip as the possible rate-controlling mechanism since "cross slip may occur only by the movement of screw dislocations, and not edge dislocations, thus allowing only partial recovery of the strain hardening and resulting in a continuously decreasing creep rate, characteristic of transient creep.'' Our tests on are-melted tungsten and powder-metallurgy tungsten displayed an extensive transient creep stage in the same temperature range but they also displayed a steady-state creep stage. The stress levels and strain rates of the two investigations, 1.4 to 7 kg mm-2 and 10-7 to 10-4 sec-1 for that of Klopp et al. and 4.5 to 10 kg mm-2 and 10-8 to 10-4 sec-1 for those of Gilbert et al., are overlapping. The activation energy for creep of our powder-metallurgy tungsten is 105,000 cal mole-1. This close agreement with the value found by Klopp et al. suggests that the same mechanism may be common to both types of materials. It may be possible to gain some additional insight into the rate-controlling mechanism by applying the analysis made by conrad22 in terms of the activation volume. The value for the activation volume depends upon the dislocation mechanism and may be used to help differentiate between various dislocation mechanisms. The activation volume for cross slip is 10 to 100 b3. Values determined from our data were 130 to 220 b3 which are in better agreement with the range of 102 to 104 b3 for nonconservative motion of jogs. Values determined from data of Klopp et al. are 240 to 1040 b3. We suggest that the rate-controlling mechanism for creep in this temperature range may be nonconservative motion of jogs assisted by enhanced diffusion along grain boundaries or dislocations. This model requires an activation energy lower than that for self-diffusion as is observed. If this is the controlling mechanism, a higher activation energy which is closer to that for self-diffusion might be expected for tests conducted on specimens with reduced grain boundary area, i.e., larger grain size. In support of this premise we have conducted tests on speci- mens having one to three grains per cross section for which a higher activation energy of 130,000 cal mole-1 was observed. Also, in agreement with results of Klopp et al., a faster creep rate resulted from the increased grain size and probable decreased dislocation density. Further argument against the cross slip mechanism is based on the constant activation energy we obsserved over the range of 5.0 to 10 kg mm-2,21 whereas the activation energy for cross slip displays a significant stress dependence.23 In addition to this, the powe on the stress term for the strain-rate dependence appears too high for cross slip. The values for tungsten fall in the range of 4.5 to 7 (Klopp et al. and Ref. 21) whereas values of approximately 2 are observed in creep by cross slip for hep metals.24 At temperatures from 3300° to 4000°F, Klopp et al. observed an activation energy of 141,000 ± 4000 cal mole-' which is less than that for self-diffusion, 153,000 cal mole-1, 25 and less than that reported for high-temperature creep of powder-metallurgy tungsten by Green:' 160,000 cal mole-1. Klopp et al. suggested that recovery of strain hardening by dislocation climb is the rate-controlling mechanism in this temperature region. Actually an activation energy larger than that for self-diffusion is predicted by this model if the temperature dependence of the elastic modulus27 is taken into consideration. Klopp et al. attributed this lack of correlation to the compositional differences between powder-metallurgy tungsten used by Green and their own arc- and EB-melted tungsten. It is our position that the value of 141,000 ± 4000 cal mole-' represents a transitional value between the higher and lower activation energies and does not represent a discrete mechanism of deformation. If the tests had been extended to higher temperatures the higher value of activation energy would have been observed as has been demonstrated by both our analy sis'' of isothermal test data by GE-NMPO28 and differential temperature tests28 on are-melted tungsten. The activation energies determined (170,000 and 160,000 cal mole-1) were greater than that for self-diffusion and are in better agreement with the value found by Green. The model of dislocation climb is associated with ; activation volume of 1 b3 according to Conrad.22 The activation volume calculated for the creep data of fou independent investigators in the temperature range where the activation energy for creep is near that for self-diffusion (Klopp et al. and Refs. 26, 28, and 30) is 110 to 2800 b3 and is in the range suggested for nonconservative motion of jogs. In the case of tungsten this mechanism may be preferred over that of dislocation climb. Sincere appreciation is expressed to Messrs. J. E. Flinn and F. L. Yaggee for the helpful discussions and suggestions in the preparation of this communication.

Jan 1, 1967

By AIME AIME

A LUSTY baby of the Institute, the Coal Division, showed that it had acquired a full set of teeth and was capable of man's work at the Division meeting at Fairmont, W. Va., on March 26 and 27. At this second of a series of field meetings, the first of which was held in Pittsburgh last fall, the industry in the East was represented from top to bottom and good humor and enthusiasm were the predominant notes. West Virginians are always good hosts and this meeting would have proved the statement to any inclined to doubt it. The spacious auditorium of the Fairmont Hotel was arranged for the technical sessions, the hotel being headquarters for the meeting. About a hundred and twenty-five representatives were registered and in attendance when Thomas G. Fear, chairman, opened the morning session at 10 o'clock Mr. Fear first introduced Howard Eavenson, vice-chairman of the morning program, who, as chairman of the Coal Division, had labored long and cheerfully to make the meeting successful. Mr. Eavenson talked briefly on what the organization was doing, pointing out that these field meetings were designed to bring the members into closer touch with the parent Institute and give the younger engineers in the field a better opportunity to participate in the work the Institute is doing. He congratulated the various committees for their work in promoting the meeting.

Jan 1, 1931

By Walter Bradley

MINING by hydraulic process of the important gold-bearing gravels of the Sacramento Valley in the basins of the Yuba, Bear and American rivers began in 1853, and continued at an ever-increasing rate for 30 years. In its most active days it reached an annual production of $15,000,000, and averaged $10,000,000 per year over the 30 years. During that period no provisions were made to prevent the debris from being dis-charged into the water courses, and ultimately large quantities of silt, sand and gravel were washed down to the lower valleys; filling channels, causing overflow of agricultural lands and difficulty in maintaining navigable depths in the Sacramento River. Agitation and suits filed because of these damages finally resulted in the injunction decision of Judge L. B. Sawyer,1 in the U.S. Circuit Court, Jan. 23, 1884, which closed down practically all hydraulic mining operations not having means to restrain their debris. In 1893 (approved March 1, 1893), Congress passed the act introduced by Representative Anthony Caminetti, of California, creating the California Debris Com-mission, composed of three officers assigned from the Engineer Corps of the U.S. Army, and since that time it has been legal and possible within the drainage systems of Sacramento and San Joaquin rivers to conduct hydraulic mining of gold-bearing gravels behind dams built under this commission's permit and supervision. In the watersheds of the Trinity and Klamath rivers, which flow directly to the Pacific Ocean and do not affect navigation or agriculture, operating permits from the California Debris Commission are not required. There is a measure of restriction there, however,. through what is known as the Trinity and Klamath River Fish and Game Dis-trict. Chap. 215, Stat. 1931, in order to secure relatively clear water for the fishing season, provides that between July 15 and October 15 each year there must not be discharged into these rivers debris that will cause a turbidity greater than a content of 50 parts per million in the

Jan 1, 1936

By Anthony Anable

THE definite trend to stricter specifications with respect to hydraulic concrete has become increasingly manifest in the last six years or so; but it remained for the vast reclamation projects of the Bureau of Recla-mation of the Department of the Interior of the last few years to focus attention on this trend, and to demonstrate how thousands of tons of concrete-making aggregates can be produced continuously and auto-matically with a control of fineness comparable with that obtained with small samples in well equipped private and governmental laboratories. Pioneer work in this direction was done, to be sure, by private com-panies, notably the Kaiser Paving Co. of San Francisco, prior to the present vast public works program. Then in 1931 came the first great, aggregates-preparation plant of the Six Companies, Inc. to supply construction materials for Boulder Dam' in Nevada, and now, in 1936, the aggregates plant of the Mason-Walsh-Atkinson-Kier Co., general con-tractors on the Grand Coulee dam in Washington. At Boulder dam and to an even greater degree at Grand Coulee dam, sand production is recognized as probably the most important single element affecting the physical characteristics of the concrete. For in the construction of dams accurate grading of the fine aggregate has consider-able bearing on the attainment of a uniform and homogeneous concrete of a high degree of workability and placeability and, at the same time, combining high density and low cement content. Low cement content is of value not only from the standpoint of economy but also because the use of an unnecessarily rich concrete causes certain undesirable characteristics to develop. This paper will relate how at Grand Coulee dam methods that are more advanced than ever before are producing four sizes of gravel and a sand having a fineness modulus of 2.5-3.0. The design capacity is 1000 tons an hour. Significantly, the methods and equipment employed are broadly those that have been used for a generation in metallurgical mills for accurately sizing and grading both precious

Jan 1, 1936