Search Documents

By Horace R. Graham

CHEMICAL nitrogen and the "nitrates" of commercial significance are derived mainly from three basic sources: (1) the natural deposits in the form of nitrate-bearing earth and clay, which, being largely water-soluble, can exist only in the most arid portions of the earth; (2) coal, which yields not only nitrogen but also the additional by-product hydrogen required for the synthesis of ammonia and its compounds; (3) the atmospheric air, which contains 75.5 pct by weight of pure nitrogen gas. NATURAL NITRATE DEPOSITS Occurrence Although natural nitrate deposits consisting principally of the salts of sodium and potassium have been reported in Egypt, South Africa, Mexico, Argentina, Colombia, Peru and the USA, the only known natural nitrate resources of commercial importance are the vast deposits found in the Atacama, Tarapaca and Antofagasta regions of northern Chile, lying in a narrow strip 10 to 50 miles wide and roughly 450 miles long, between latitudes [19O] and [26OS]. In addition to yielding nitrates of sodium and potassium, these deposits are the source of the major portion of the world's supply of iodine. The nitrate-bearing ores known in Chile as caliche are variable in composition and may contain from 5 to 30 pct each of nitrate, chloride and sulphate. While the deposits are present chiefly in the form of the sodium salt, potassium, magnesium and calcium also occur in percent- ages from 0.1 to 5; usually as double salts with sulphate, which are but slightly soluble in nitrate leach solutions. These double salts are bloedite(Na2S04.MgS04.4H,0), glauberite (Na2S04.CaS04), polyhalite (K2SO4.- MgS04.2CaS04.2H20). Some deposits contain up to30 pct of their ni-

Jan 1, 1949

By Jack L. Taylor

WITH the exception of the work of Vogel,&apos; and Rolla and Iandelli, very little information has appeared in the literature on titanium binary systems with the rare earth elements. Rare-earth additions to titanium alloys may possibly parallel the beneficial effects on the physical properties of certain steels. Having this in mind, some knowledge of solubility limits and intermediate phases, if any, would be useful. An investigation of the titanium-rich Ti-Ce system was started. Alloy Preparation The iodide titanium from the New Jersey Zinc Co. and the cerium metal from the Institute for Atomic Research Ames Laboratory used in this work were supplied with the typical analysis shown —iodide titanium: 0.0065 pct Mn, 0.0022 pct Fe, 0.0015 pct Cu, and 0.0042 pct Pb; cerium metal: <0.01 pct Fe, <0.03 pct Si, <0.05 pct Ta, <0.02 pct Pr, <0.03 pct Ca, <0.02 pct Mg, with no trace of Nd, La, or Th. The cerium metal, stored in oil, was washed and scraped just before weighing into capped cups machined from iodide titanium. The cold hearth helium-arc furnace described by Schramm et al3 was used for melting. The alloy buttons from the arc-melted cup were cut in two, mounted, and examined. Homogeneous alloys were demounted and rolled to approximately 1/4-in.sq bars. Sections l/8 in. thick were cut from the bar to provide samples. The Ti-Ce alloy buttons analyzed for cerium were of the following composition: 0.19, 0.36, 0.48, 0.61, 1.15, 2.52, 3.06, 3.70, 4.30, 9.20, 14.26, and 18.50 wt pct. Nominal

Jan 1, 1958

By W. I. Duvall, L. D. Sadwin

Three explosives with different detonation characteristics were tested by studying their cratering ability in a granite-gneiss. The strain wave generating characteristics of these explosives were also studied in the same rock medium. Correlations between the relative performance of three explosives as evaluated by crater studies and other methods of evaluation are indicated. Numerous test methods have been employed to evaluate the output performance of explosives; for example, the underwater explosion method, the airblast method and the ballistic pendulum method.&apos;*&apos; For blasting applications, the study of explosion produced craters and explosion generated strain waves are the most meaningful. This laboratory has employed these techniques extensively for many years and has shown that the detonation properties of explosives and their ability to generate strain waves in rock are related and that the amplitude and shape of the strain wave is related to some of the crater parameters such as slab thickness and fly rock velocity.3&apos;11 However, a good comparison between the relative performance of explosives as determined by the crater and strain wave methods had not been made. The purpose of this investigation was to determine if the relative performance of three explosives as determined by the crater method shows a correlation with the relative performance as determined by the strain wave method. If a good correlation exists between these two sets of relative performance, it should then be possible to relate the detonation properties of an explosive to its ability to break rock in a crater test. In most commercial blasting operations, the diameter of the blast hole remains constant even though the type of explosive may change. In general, it is the explosive volume rather than the weight which remains constant when two or more explosives of different density are compared. Therefore all tests in this investigation were conducted on a constant volume basis rather than on a constant weight basis. TEST SITE AND ROCK PROPERTIES The tests described in this paper were conducted at a granite quarry owned and operated by the Consolidated Quarries Div. of the Georgia Marble Co. at Lithonia, Ga. The tests were performed in an area where the exposed rock surface was nearly horizontal and where the general rock mass had few joints or faults. The rock has an apparent sp gr of 2.6 and a longitudinal propagation velocity of 18,000 fps. The characteristic impedance of Lithonia granite gneiss is 53(lb - sec/in3). EXPERIMENTAL PROCEDURE There are many parameters which must be considered in the study of explosion-produced craters. The role played by each variable in the explosive-rock-crater system can be determined by experimental techniques in which one parameter is varied while others are maintained constant. In this investigation, the crater geometry was studied as the depth was varied for each of three explosives. The explosive volume and rock-type were held constant for all crater tests. The experimental arrangement used in performing the crater tests is illustrated schematically in Fig. 1.

Jan 1, 1965

By J. H. Swisher

ALUMINUM deoxidation equilibrium in liquid iron has been the subject of many investigations. Sawamura and Sano1 have written a critical survey of the literature on this subject and consider the data of Gokcen and chipman2 and of d&apos;Entremont, Guernsey, and Chip-man3 to be most reliable. The present study was undertaken to check these data and extend the range of the experiments to lower temperature. The experiments consisted of equilibrating 5-lb Fe-Al melts with recrystallized alumina crucibles at 1580o + 10oC, and analyzing the solidified ingots for aluminum and oxygen. The electrolytic iron stock contained 100 ppm C, 20 ppm 0, and trace amounts of other elements.* The stock was induction-melted in an atmosphere of 5 pet H2 in argon to attain equilibrium between the melt and the crucible. The temperature was measured with a W, 3 pet Re/W, 26 pet Re thermocouple, and the equilibration time was about 4 hr. The results are plotted in Fig. 1 along with curves obtained from the data of d&apos;Entremont et al.,3 for temperatures of 1740o and 1910°C. The present results can be seen to be consistent with the previously reported high-temperature data. The reaction under study is AI2O3 (s) = 2 Al (l) +3O [1] for which the deoxidation product is Kl =[% Al]2 [%O]3 [2] (Under the experimental conditions, Fe A12O4 is not expected to form.4) In Fig. 2, values of log Ki evaluated at 0.01 pet A1 are plotted against 1/T, using data obtained from all the investigations under consideration. The deoxidation product is plotted in Fig. 2 in lieu of the equilibrium constant (normally obtained by evaluating Ki as pet A1 — 0) because of the uncertainty involved in extrapolating to zero concentration. The difficulty in extrapolating the present data for 1580°C is apparent curvature in the log Ki vs pet Al plot. This curvature is perhaps due to the uncertainty in oxygen analysis for concentrations of 5 ppm and below. For the data of Gokeen and chipman,&apos; the extrapolation is also difficult because of experimental scatter. The line drawn through the points plotted in Fig. 2 may be represented by the equation:

Jan 1, 1968

By David B. Reger

Extensive drilling for gas and increased pipe-line building were the major petroleum activities in West Virginia during 1937. According to the West Virginia Department of Mines, 1034 permits to drill were issued. A running account of operations from trade journals and other reports shows that 1041 wells were drilled, resulting in 193 oil wells with 1238 bbl. of daily production; 680 gas wells with 1,048,057,000 cu. ft. of daily open flow; and 168 dry holes. The new oil-well average is 6.4 bbl. per well per day; the gas-well average is 1,541,260 cu. ft. per well per day; the ratio of dry holes to completions is 16.13 per cent. Very little attempt was made to develop new supplies of oil. Because of the continued low price, operators evidently considered it good business to leave oil in the ground rather than to produce it at a loss or on a small profit basis. The principal oil wells completed, by counties, are: Calhoun, 16; Clay, 10; Pleasants, 17; Ritchie, 42; Roane, 16; Tyler, 13; Wetzel, 11; Wirt, 14; Wood, 13. The leading counties in gas, with the number of successful wells in each, are: Boone, 54; Braxton, 31; Cabell, 48; Calhoun, 46; Gilmer, 82; Kanawha, 134; Lincoln, 44; Ritchie, 56; and Wayne, 26. General State of the Industry In Table 1 will be found an approximate summary of oil and gas territory and reserves, oil and gas production and number of oil and gas wells. The amount of land under lease is an approximation, because the exact figures are not available through any public or private agency. The proved land and reserves represent the opinion of the writer. The oil production for 1937 is subject to revision, and the gas production for the same year is only an estimate, based on demand and supply. The number of oil and gas wells now active is also an approximation, based on previous studies, and revised for completions and abandonments. Principal, Areas of Activity In Boone County, 62 wells were drilled in various localities, resulting in 4 oil wells and 54 gas wells with 18,170,000 cu. ft. of new production.

Jan 1, 1938

By AIME AIME

A THOROUGHLY satisfactory crowd turned out at the fall meeting of the Industrial Minerals Division and took an active part in the entire program. On Thursday afternoon, Sept. 24, a limestone plant was inspected, technical sessions occupying the attention of the visitors all day Friday and Saturday morning. Headquarters were at the Nittany Lion Inn, an attractive hostel on the Penn State campus, at State College, right in the center of Pennsylvania. We are still in the dark, despite inquiries, as to just what breed of lions Nittany lions are. As nearly as we could find out, Nittany is not a Biblical name, as it sounded to us, but a corruption of the name of an Indian princess, or maiden, or maybe just girl that haunted those parts in bygone times and after whom a near-by mountain was named. Penn State athletes are "lions" and there you are. The meeting was supposed to be a joint one with the American Ceramic Society&apos;s Materials and Equipment Division; but it was quite evident that the Institute had a much better publicity agent than the Society, which bothered Ross. Purdy, the aggressive secretary of the ceramic people, no end. However, Secretary Purdy saw to it that everyone present fully understood that the Ceramic Society was present, so that that contingent all but stole the show, its representatives presiding at every meeting. The Pittsburgh Section of the American Ceramic Society was also supposed to be holding its fall meeting there at the same time, but made no trouble at all for anybody, as one of the speakers remarked.

Jan 1, 1936

By Kenneth S. Ritchie

TOO often, many foremen; superintendents, managers, and executives, "The Bosses" of the oil and mining industries, do not fully realize: (1) How much personal actions &apos;.on the job" may reduce their effectiveness in getting work done; and, (2) The importance of harmonious relations with their fellow men. Today. these qualities of personality in the people entrusted with the positions of responsibility are more important than ever with the shortages of labor so critical in vital war production. Likewise, many engineers do not fully realize that their work is essentially executive in character; i.e., other people do the actual labor. Without their help. the engineer&apos;s work would not be done. A clearer appreciation of this fact would increase their interest: (1) in the nontechnical aspects of their work. and, (2)in their relations with others, particularly the individuals in their own organization. Consequently, these engineers would be more successful in equipping themselves for greater responsibilities and increased remuneration.

Jan 1, 1944

By G. Sandoz, D. A. Meyn

The fracture surfaces of specimens of titanium a1loys which exhibited susceptibility to subcritical crack growth in a wide variety of environments, including aqueous solutions, alcohols, hydrocarbon gases, carbm tetrachloride, and dry air, were examined. The dominant and characteristic fracture mode was cleavage. which became mixed with an increasing porportion of ductile fracture modes (dimples. and so forth) as the applied KI was increased. The cleavage plane in all the alloys was oriented at 15 deg from (0001) of the a phase. No indices could be assigned to the 15 deg cleavage Plane because of uncertainty as to which zone it belonged to. SLOW crack growth and delayed fracture take place in certain titanium alloys at stress intensity (KI) lower than the critical values for complete fracture (KIc) found in short-time tests for plane strain fracture toughness.&apos; Such crack growth may take place in very dry air on sustained loading if the alloy contains a sufficient amount of hydrogen and if the stress intensity factor is higher than a threshold value designated KIH.2 Similarly, a number of environments such as water, alcohols, and hydrocarbons may cause slow crack growth provided the stress intensity factor exceeds the threshold value KISCC. In this paper it is intended to examine some fracto-graphic and crystallographic details of this subcritical crack propagation process as related to alloy composition, environment, and stress intensity. It has been previously reported that subcritical crack growth takes place in titanium alloys in aqueous environments by cleavage.2"6 The observations to be described here indicate that in the alloys investigated the mode of subcritical crack propagation is more dependent on the stress intensity during cracking than on the environment. The fracture mode is illustrated with photographs of the fracture surfaces at a wide range of magnifications. The crystallographic character of the cleavage mode is also presented and the results discussed. EXPERIMENTAL APPROACH The studies were made on four titanium alloys— Ti-8A1-1Mo-lV, Ti-5A1-2.5Sn, Ti-7Al-1Mo-lV, and Ti-0.350. Of these four alloys the first two were mill annealed and fine grained. The latter two were noncommercial and coarse grained, having been prepared for other experimental purposes. The crystallographic studies required a large-grain size. Consequently the fine-grained alloys were an- nealed in a vacuum at 1950°F and furnace cooled to produce samples for these studies. This treatment did not alter the microstructure significantly except for grain size. All the aluminum-containing alloys showed primary a with a network of ß-phase particles within the a grains; Figs. 1 and 2 show this microstructure for the specific case of fine-grained Ti-8A1-1Mo-1V. The cracks in the figures will be discussed later. Fractographic studies were made on all the alloys, but the electron fractographs displayed herein are from the Ti-8A1-1Mo-1V alloy in the fine-grained condition. Emphasis was placed on this commercial alloy because considerable information was available on the stress-corrosion cracking characteristics in a variety of environments. Sufficient supplementary studies of the alloy after the anneal to produce large grains were conducted to establish that the stress-corrosion cracking susceptibility and fractographic characteristics were not changed significantly. Thus it could be inferred that the crystallographic data obtained exclusively on large-grained specimens would apply also to fine-grained specimens. Fracture surfaces for study were obtained using precracked cantilever beam specimens loaded as described by Brown. The precracked section of a specimen was immersed in the environment of interest. Values of initial stress intensity factor Kli were chosen slightly higher than KISCC in order to obtain a fairly extensive region of slow crack growth. Fracture surfaces representative of a variety of stress intensity levels could then be examined because in the cantilever beam test KI increases as the crack propagates.

Jan 1, 1970

By J. R. O’Connor

Stimulated emission from Nd+3 in yttrium uanadate fYVOJ is reported. Single crystals of YVO4:Nd, obtained from Linde Col-p., have improved substantially in the last several months. Pulsed thresholds of YVO, laser rods are now approximately 2 to 3 5, cowparable to tliose for YAG:Nd. Yttrium uanadate crystalli~es irz a space group similar to zircon. All rare-earth vanadates have this structure. Rare-earth ions sucll as Nd+3 which substitutes for Y+3, aye situated irz a strong tetragonal crystal field which lacks inversion symmetry. This condition increases the p&apos;robability of the parity-forbidden f — f transitions. Yttrium anadate has strong absorption bands beyond -1000A. These are clue to Y-O, V-O charge transfer and molecular transitions. Under 2537 and 3660A irradiation pure YVO, fluroresces u bright yel-LOLO. This fli&orescence is corrzpletely quenched in YV04:Ncl crystals. This and other evidence of energy trut~sjer from the lattice is repovted. Optzcul atz 1user pvope 1-ties o! YI&apos;U4:E[t are brieJy described. THIS paper describes some of the optical and laser properties of Nd+3- and Eu+3-doped yttrium orthovana-date (YVO4). It reports laser action for the first time in this low-symmetry host. For some time we have pursued a research program concerning laser hosts&apos; wherein the rare-earth (RE) ion is situated at a site of low crystal symmetry so as to increase the probability of radiative transitions. Single crystals of doped and undoped YV04 are grown from iridium crucibles in an oxyhydrogen gas-fired furnace by a modified Czochralski technique.&apos; This material crystallizes in a D4li tetragonal space group of the zircon (ZrSiO,) type.3 All RE vanadates have the same structure and form solid solutions with YVO4. Therefore, it will be possible to investigate a variety of cross-pumped laser systems, as in the case of yttrium aluminum garnet (YAG).4 At present, ~d&apos;~-doped YAG is one of the most efficient solid-state lasers.5 Accordingly, most of the material to follow will compare the properties of YV04 to those of YAG. Fig. 1 shows the relative transmission of YAG and two types of YVO4. "Pure" YVO4 has a normal absorption edge and is colorless. A second type has a broad absorption peaking near 4200A and is yellow. Rubin and Van uitert6 suggest the yellow material is slightly reduced. Samples of each type are being investigated by electron spin resonance,7 but these studies are so far inconclusive. The pulsed laser threshold is much lower in the yellow material than in the colorless. Therefore, the absorption at 3500 to 5000.4 transfers energy to the Ndi3 ions. Photons of wave length between 2000 and 4500A cause undoped YVO4 to fluoresce at 4800, 5250, 5460, 5540, and 5750A. This emission, previously reported by Brixner and Abramsom,8 is partially quenched by EU&apos;~ and completely quenched by Ndt3 at room temperature due to energy transfer from the lattice to the RE ions. At low temperatures, some lattice fluorescence is present. This implies that the energy-transfer process is in part phonon-assisted. Although the YVO, single crystals used in this work were prepared from Y2O3 containing less than 0.01 pct rare-earth impurities, there is aopossibility that emission lines between 4800 and 5750A are due to dysprosium, terbium, and so forth. However, these lines are not observed in other compounds, prepared from Y2O3, such as YP04, Y2MoO6, and so forth. Furthermore, extensive absorption measurements on our "pure" YV04 single crystals between 0.4 and 5.0 failed to reveal any characteristic rare-earth lines. Fig. 2 compares the absorption spectra of Ndt3-doped YAG and YVO4from 0.6 to 1.0 . The Ndt3 absorptions are labeled according to free ion, R-S coupling. These term designationsQ are appropriate for YAG:Nd. They appear to be inappropriate for YV04:Nd. In YVO, neodymium must substitute for yttrium. The yttrium site is situated In a strong tetragonal field, where point symmetry is (42m) or possibly lower.1° However, the reduced splitting of the Stark components of the YV0,:Nd spectrum implies that the NdT3 ion is in a cubic site. The only plausible explanation for this discrepancy is that the Ndt3 ion is in a low-symmetry site, lacking inversion symmetry, so that a substantial admixture of 4f and 5d wave functions occurs. In this case, R-S coupling is not valid and J is no longer a good quantum number." Consistent with this view, the 4~ metastable level of YV04:Nd has an oscillator strength larger and a

Jan 1, 1968

By G. Bhat, J. F. Libsch

A STUDY of the kinetics of embrittlement in engineering alloy steels during tempering has indicated that the presence of alloying elements may define two distinct regions of embrittlement: 1) at 800° to 1000 °F, termed low temperature embrittle-ment, and 2) in the temperature range 1150 ° to 1250°F, termed high temperature embrittlement.13 It has been suggested that embrittlement in each region may be due to a different mechanism. At intermediate temperatures and extended times the course of embrittlement may be influenced by the superposition of the embrittlement occurring in the two regions. Furthermore, low temperature embrittlement has been known to decrease as the temperature is raised slightly above the maximum embrittlement range.&apos; Jaffe and BuffumV ave presented data for a Ni-Cr steel illustrating the removal of the em-brittlement occurring at 932°F by reheating to 1250°F for an hour. Their data further shows that embrittlement proceeds continuously with increased time at 1250°F, becoming pronounced at long times. They interpreted this behavior as a retrogression phenomenon involving the solution of the small nuclei of precipitate formed at 932°F as the temperature was increased, and reprecipitation of larger nuclei stable at 1250°F, with the reoccurrence of embrittlement. It appears desirable to reconsider this explanation in the light of the two regions of embrittlement proposed by the authors1 for some alloy steels. In addition, it appears desirable to determine any influence of a preconditioning treatment in each temperature range upon subsequent development of low and high temperature embrittlement. It is thus the object of this investigation to study the characteristics of the two modes of embrittlement proposed in a commercial Ni-Cr alloy steel (AISI 3140). Experimental Details Material—The material used in this investigation was commercial AISI 3140 steel bar stock, received as % in. hot-rolled rounds. The steel analysis was as follows (in percentages): C, 0.39; Mn, 0.79; Si, 0.30; S, 0.028; P, 0.015; Ni, 1.26; and Cr, 0.77. Material Processing and Heat Treatment—The bar stock was first ground to 0.430 in. squares and cut into specimens 23/4 in. long. These specimens were austenitized at 1650°F for 1 hr and oil

Jan 1, 1958

By R. W. Armstrong, D. H. Feisel

Self-diffusion in pure crystalline solids has been described through extension of the Cohen and Tum-hull volume -fluctuation model originally proposed for diffusion in simple liquids. It is shown, for a number of crystalline solids, that the self-diffusion coefficient, D, obeys the relationship where a is the lattice spacing, v the Debye frequency, Z&apos; the lattice-volume fluctuation per atom required for a diffusion jump, and (?V/Vo) the relative increase in the lattice volume resulting from thermal expansion between O°K and the temperature under consideration. The calculated value of Z&apos; is dependent upon the difiusion mechanism and the lattice geometry. ThE need for an increased understanding of mass-transport processes in crystalline solids has resulted in much research to determine rates of self-diffusion.&apos; For several metals (e.g., copper, silver, and iron), the experimental values of the self-diffusion coefficient, D, have been determined over a large interval of temperature and the accuracy of D has been investigated through repeated experiments. Also, a number of empirical and theoretical diffusion studies have established a rational basis for understanding the D values for the different elements.2"6 The empirical diffusion analysis by Sherby and simnad6 supplied the main stimulus for the present study. Sherby and Simnad, reviewing the self-diffusion data for a substantial number of pure crystalline solids, suggested that sufficient data were available to establish with some certainty the apparent intrinsic material properties which influence D. Without explicit regard for any mechanism of diffusion, these investigators obtained an empirical relationship for D which correlated the self- diffusion coefficient for each element with the melting temperature, crystal structure, and valence of the particular element. Their analysis is only unsatisfactory in that the effect on D of crystal structure is not very clear and the valence to be assigned to an element is not always straightforward. The present study is an attempt, from a very different viewpoint from that of Sherby and Simnad, to establish a basis for understanding the self-diffusion coefficients for crystalline solids. This analysis was undertaken for the purpose of developing a general expression for D which would explicitly depend on the mechanism of diffusion. The main result of the study is that diffusion in crystalline solids may be described in terms of a volume-fluctuation model which was originally proposed by Cohen and Turnbull7 to describe diffusion in simple liquids. The model appears to be useful for predicting self-diffusion coefficients in crystals. The following sections describe the volume-fluctuation model for diffusion, the application of this model to crystals, and the resultant agreement with experimental data. 1) THE VOLUME-FLUCTUATION MODEL FOR DIFFUSION Cohen and Turnbull7&apos;8 developed their model for liquid self-diffusivity for the purpose of describing certain properties of liquids, glasses, and the liquid-glass transition. A hard-sphere model for the liquid structure is used. In this model, the size of a spherical molecule or atom is fixed for all temperatures by the interatomic spacing at the absolute zero of temperature. At any temperature above O°K, the atom is viewed as being contained within a larger spherical cage defined by the interatomic spacing of the atoms at that temperature. A random distribution of varying cage sizes is assumed to exist in the liquid. An individual diffusion jump occurs when the free volume of an atom (the volume of the cage containing the atom minus the volume of the atom) is large enough for the atom to jump out of its cage. With this physical picture of diffusion in liquids, Cohen and Turnbull derive the following equation for self-diffusivity: D=Doe-yv*/vf [1] where Do is the product of three factors which are the diffusion-path geometry, the diffusion-jump distance, and the velocity of the diffusing atom, v*

Jan 1, 1964

By P. Bandopadhyay, T. C. Rao

Geologically the Indian coals belong to Gondwana formations. Being of drift origin, these coals contain high percentage of mineral matter distributed in finely disseminated form. Indian coal-preparation plants process prime coking and medium coking coals for use in steel plants. Limited resources of good quality coking coals (Table 1) could not keep pace with the rapid developments of the iron and steel industry in India. This resulted in the introduction of coal-preparation technology and the establishment of washeries in India in the last 30 years or so. The first four washeries were set up during the early fifties at West-Bokaro, Jamadoba, Lodna and Kargali. Next came the first non-coking coal washery at Nowrozabad set up by the Associated Cement Company. In 1961, following the recommendation of Central Coal Washeries Committee (1953-54), Hindustan Steel Ltd. had set up five central washeries at appropriate locations, viz Durgapur, Dugda (2 washeries), Patherdih and Bhojudih, so that the raw coal feed having similar washability characteristics can conveniently come from a number of collieries to a particular washery. Subsequently, to meet the increasing demand of metallurgical coal by steel plants, two more central washeries (at Durgapur and Chasnala) and three pit-head washeries (at Kathara, Swang and Gidi) were installed by 1970. The prime objective of washing Indian coking coal is essentially to reduce the ash content. All the washeries in India, taken together have an installed capacity of about 26 million tons of raw coal input per annum. Details of these washeries in respect of their annual capacity, main washing systems adopted and the nature and size of the products are given in Table 2. It can be observed from this table that (1) bulk of the coal is processed in units like jigs HM baths and HM cyclones; (2) only two of the washeries have cleaning circuits for treatment of fines.

Jan 1, 1980

By Alfred H. Brooks

LESS than a decade ago the consumption of coal in Alaska was practically limited to the salmon canneries and the few lode-mines and settlements along the Pacific coast of the Ter¬ritory. The sparse population of the interior depended on the forests, that of the shores of Bering Sea and the Arctic Ocean on driftwood for fuel. All this has changed. The thousands who have sought and mined gold on the Seward peninsula since 1898 have much impoverished the long-accumulated supply of driftwood, and at the same time the constantly increasing demand for fuel, on the part of the placer-camps and steamers, has resulted in heavy inroads being made on the accessible timber of the Yukon and its tributaries. While on the one hand the immediately available store of wood has decreased, on the other the consumption of fuel because of the rapid expansion of the mining and fishery industries and the attendant growth of population has much increased. Alaska, therefore, offers a constantly growing market for coal and other fuels. As the local coal-production has been insignificant, the demand has been met by importations from Washington, British Columbia, and even from Pennsylvania and Australia. Fuel-Consumption Mr. D. H. Jarvis, Collector for Alaska, has kept systematic records of the trade of the Territory since 1903. The statistics of the coal-importations of the past two years are shown in Table I. If data were available for a longer period of years, the increase of coal-importations would be much more striking.

Jul 1, 1905

J. J. MCLELLAN, Webb City, Mo.-The Media mill, at the time it was built, was the largest mill that had been designed in the Joplin district. It was put up in a hurry, to take advantage of the high prices for zinc ore in 1915, by the owners of an adjacent plant, which had been very profitable. They owned a compound Corliss engine, and to take advantage of a single-unit drive it was necessary to build the mill in the form chosen, which involved making the hopper feed directly through the breakers and rolls, the undersize from the screen passing at once to the jigs, the oversize going through the rolls and returning to the original trommels. The mill was built in fairly good proportion; crushing was done by jaw breakers, Webb City pattern,&apos; and three sets of 42-in. (106.7-cm.) Cornish rolls for reducing the oversize. The jigs were larger than the usual practice. The roughers were two six-cell jigs, with 42 by 48-in. cells. The cleaner jig was the largest ever constructed in the district up to that time, having seven 36 by 48-in. cells, for treating the rougher jigs. There was also a chat rougher. "Smittem," as used in our district, is the partly concentrated product from the rougher, which is finished on the cleaner jigs. "Chats" are the middlings proper, that is, they are the grains of chert with included particles of sulphide; the very low-grade smittem is sometimes included among the chats. When drawing chats from a jig, we also draw about ten times greater quantity of barren chert in order to insure complete recovery of mineral. This mixture of middlings and tailings is taken to a set of 30-in. rolls, the crushed product then going to a chat rougher, a comparatively small jig, with 26 by 36-in. cells. The principal departure of the Media mill from the usual practice was to build a hopper sufficiently high to give gravity feed to the jigs, without using elevators. The sludge plant, for table treatment of sand and slime, also contained several innovations in the manner of distributing the feed. The tables were arranged in two rows and the feed ran around the outside in a launder having two or three cone classifiers

Jan 1, 1918

Bailey, Lewis Newton, Master Engineer, Senior Grade, 4th Regiment, U. S. Engineers, Headquarters Company, died of pneumonia at Camp Merritt, N. J., on April 30, 1.918. Baird, Louis, Lieut., Royal Field Artillery, British Army, died on the battlefield in 1915. Cobeldick, William Morley, Royal Engineers, died from gas poisoning on October 7, 1915. Dougall, Ralph, killed in action Evans, Alfred Winter, Lieut.-Col., New Zealand_ Rifle Brigade, D. S. 0., D. C. M., killed in action on October 12, 1917. Hague, William, 1st Lieut., Engineer Officers&apos; Reserve Corps, died in active service.

Jan 8, 1918

By AIME AIME

EVEN the weather man joined in a friendly conspiracy to make the fall meeting of the Industrial Minerals Division at Rolla, Mo., Oct. 23-25. the splendid surges that it was. Following weeks of rain, the foliage of the Ozarks was still green, merely enlivened here and there by splashes of autumn coloring. In contrast to the tranquil beauty of the School of Mines campus under smiling Indian summer skies, the pace of the meeting was lively. Registration was larger than at any previous meeting and included an unusual number of prominent names and delegates from all over the country. From 125 to 150 were present throughout the three technical sessions, at the Thursday evening smoker, and also at the banquet on Friday; when students trooped in to the technical sessions the audience was augmented occasionally to over 200.

Jan 1, 1941

While the production of this state has not realized the early hopes that this coal would replace eastern coal on the Pacific Coast, it has been steady though small. Nearly all of the tonnages given are from Goodyear&apos;s, The Coal Mines of the Western Coast of the U. s., a carefully com- piled and accurate account of the development of the industry along the Pacific. [ ]

Jan 1, 1942

By Donald Barton

THE theory of gravitation is based on Newton&apos;s law that any two bodies exert a mutual attraction which is proportional to the product of their masses and inversely proportional to the square of the distance between them; i. e., A =KRM/R2 (1) where K is a constant, M and m are the respective masses of the two bodies, and R the distance between them. In the earth&apos;s gravitational system, the earth is one of the bodies; the other may be any body within or without the earth. In theoretical dis¬cussions and calculations in regard to gravity, that other body usually is taken as a unit of mass: in the C. G. S. system, a body of one gram in mass. GRAVITY AND LEVEL SURFACES Gravity is defined in geophysics as the force of attraction exerted by the earth, towards itself, on a body of unit mass. The intensity of gravity is usually expressed in dynes of force or in centimeters of acceleration. In geophysical work in America, most commonly it is expressed in dynes (per gram) with the "per gram" understood and not directly expressed. In geophysical work in Europe, most commonly it is expressed in centimeters per second per second (cm./sec.2) and less commonly merely as centimeter-gram-second units (C. G. S.). At sea level, the intensity of gravity amounts very nearly to 980 dynes. The vertical is the direction along which the attraction of gravity is exerted at any point. . In most cases, it is very nearly, but not quite, per¬pendicular to the earth&apos;s surface. The path that would be taken by a body falling freely through space toward the earth is vertical at each point and may be spoken of also as "the vertical," or as the line of the vertical, or as a line of force of gravity. At the earth&apos;s surface it com¬monly is very nearly, but not quite, a straight line.

Jan 1, 1928

By C. C. Herrick

The vapor pressure of indium has been measured by the torque-effusion technique, as a function of temperature between 1102o and 1422oK. For liquid indium, the vapor pressure (in atmospheres) can be represented by the equation -R In P = 5.782 x104/T - 25.29from 1000o to 1422oK. Extrapolation yields a calculated normal boiling point of 2329°K and a heat of vaporization at 298 oK of 58.09 kcal per mole by the third-law method and of 58.39 kcal per mole by the second-law method. Calculations indicate that the free-energy functions of Hultgren are to be preferred to those of Guruich. BECAUSE of the potential uses of liquid metals, it is important that convenient experimental methods be developed which will lead to a sufficient body of thermodynamic data so that reasonable estimates of properties of liquid metals can be made. Indium is particularly well-suited to investigation, since it remains liquid over a long temperature interval, it alloys readily, suitable containers for it are easily procured, and relatively few investigations of its thermodynamic properties in the region above 1000°K have been made. PREVIOUS RESEARCH The first determination of the vapor pressure of indium was made by Anderson,&apos; using the Knudsen method and silica-lines stainless-steel cells. Kohlmeyer and spandau2 determined the normal boiling point, and a mass-spectroscopic investigation has been made by Lyubimov and Lyubitov.3 (Unfortunately, only an equation representing the data of the latter investigators has been available to us.) Hultgren et al.4 and Gurvich5 have published discordant tables of the free-energy functions for indium. EXPERIMENTAL METHOD The torsion-effusion principle has been described amply in the literature.8,7 With this method, one observes the angular deflection induced by effusion of vapor from a multihole effusion cell which is suspended from a filament producing a small rotational restoring force. The pressure within the effusion cell can be computed from the relation ziaifiai where k is the torsion constant of the filament, 6 is the observed angular deflection, and ai, fi, and qi are the area, force factor, and moment arm of the ith effusion orifice. The force factor f is analogous to the Clausing factor,&apos; and corrects for the reduction in effusive force attributable to the finite geometry of the effusion orifice. Schultz and Searcy&apos; have tabulated the force factors for various tube geometries. EXPERIMENTAL APPARATUS The physical arrangement employed in this study is shown in Fig. 1. The furnace elements are six Globar heat rods with 15-in. hot zones. Temperature is maintained to * 1°K by a Beck mechanism driving two 26-amp Powerstats in parallel. A Pt (Pt, Rh 10 pct) thermocouple serves as the sensing element. Four inner tubes act as vibration isolators; the air pressure required for maximum isolation was determined empirically, and is maintained by a solenoid valve. The tungsten fiber, 9 by 0.002 in., is joined to an 0.008-in. tungsten wire or graphite rod via a machined lightweight chuck.

Jan 1, 1964

By C. C. Nitchie, G. S. Brooks

With the gradual depletion of the natural-gas pools of the Kansas district, together with the uncertainty of further cheap fuel developments, some of the western zinc companies turned to the coal fields, attracted by their permanency and the success of the Matthiessen & Hegeler Co. and the lllinois Zinc Co. Being then confronted with the problem of using a relatively high-priced fuel, although the ultimate supply was very great, the fuel economies of the kilns and furnaces became of far more importance, and the more modern equipments, as a result, embodied distinct gaias in this phase of the business. In addition, there have been some pronounced advances in the actual making of gas from these coals. Increased efficiency in gas making has contributed its hare to lowering costs and those plants located in the higher priced fuel districts have probably been obliged to study these economies somewhat more closely. Naturally, many beneficial changes have resulted in both practice and apparatus in these sections. On certain western coals, for instance, the actual saving in fuel consumption has been 50 per cent. By this is meant that, where about 1.75 tons were burned to smelt 1 ton of oxidized ore, 0.7 to 0.9 ton is now required. While comparisons by T. R. Ingalls1 of fuel economies in smelting in this country and Germany before the war may, in general, be correct, they do not appear to do justice to the more progressive American practice. It is doubtful whether German plants were substantially bettering these fuel ratios. Data furnished by Bender and Frams do not afford records averaging less than 0.9 ton coal per ton ore on materials from 40 per cent. to 50 per cent. zinc. Fuels As producer fuel, Illinois, Indiana, and Kansas coah offer a wide range of material, although varying much in their amenability to gasscation. The proper fuel for each plant can only be determined after com-

Jan 1, 1920