Search Documents

By J. C. Bokros, A. S. Schwartz

The irradiation-induced densification of pyrolytic carbon has been shown to take place by a simple first-order rate process. The values of the densification constant, kd, for isotropic carbons are 1.0 x 10-22, 1.4 X 10-22 and 2.8 X 10-22 (nut)-1 at irradiation temperatures of 520o, 670°, and 1000oC, respectively. The apparent activation energy obtained from the temperature dependence of kd for isotropic carbons is about 0.2 ev. Estimates of the maximum stresses that develop in isotropic carbons owing to shrinkage onto an unyielding support show that stresses in excess of 15,000 psi may be avoided during irradiatian at 600" and 1000°C if the initial coating density is kept above 1.5 and 1.9 g per cu cw, respectively. If a carbon coating on an unyielding support is not completely isotropic, stresses may continue to build up at high neutron exposures after densification is complete because of continued anisotropic distortion. Stresses in excess of 15,000 psi from this source may be avoided during irradiation at 1000°C if' the Bacon anisotropy factor is kept below 1.3. A variety of applications of carbon and graphite in nuclear technology has stimulated numerous studies of the effect of neutron irradiation on these materials One of the most interesting problems associated with the use of carbons and graphites in the high fast neutron fluxes of nuclear reactors arises as a consequence of the neutron-induced dimensional changes that occur during irradiation. Energetic neutrons displace car- bon atoms from their lattice positions; and, depending on the temperature, the interstitials and vacancies produced migrate to form clusters, recombine, or are annihilated at dislocations or crystallite boundaries. The competition of various sinks for the point defects results in structure-sensitive bulk-dimensional changes that vary with temperature in a complicated way. This paper deals with the neutron-induced dimensional changes in turbostratic carbons that are being used as coatings on nuclear fuel particles. Details of the structure of these carbons and the variations of their structure with deposition conditions have been reported.'-3 It has been shown in previous work that the neutron-

Jan 1, 1968

By R. L. Whiting, H. J. Ramey

The basic study from which this paper was prepared was started as the result of the growing need throughout the world for increasing quantities of energy in all forms. Quite obviously, natural forms of energy that are readily available at low development cost are those in greatest demand. The underdeveloped countries — and particularly those having little or no petroleum resources — are the countries in which the most interest is being shown in the newer energy sources. One of the least expensive energy sources is natural geothermal steam.'-* Although this form of energy has been recognized for centuries, it has been only during the past 20 years that serious efforts have been made to harness it. Natural geothermal steam energy in Italy, New Zealand, Mexico, Japan, and California is now being produced through wells to drive turbines and generate electricity. Further, active exploration for natural geothermal steam is being conducted in Hawaii, Fiji, Taiwan, Chile, Russia, Greece, and Katanga. It is surprising to find that most geothermal steam exploration is in the "steam seep" stage. That is, surface studies are made and exploratory wells are drilled in the general area of steam seeps. However, in the larger geothermal steam areas, there have been efforts to apply the most modern geological and reservoir engineering principles in order to define the reservoir parameters, particularly those relating to estimates of reserves and future productivity. This paper is concerned with the development of appropriate equations and techniques to facilitate these estimates. Production of natural steam or hot water presents problems different from those experienced in the production of oil and gas. For example, steam or hot water systems may be essentially single-component systems, while hydrocarbon systems are most frequently multicomponent fluid systems. Heat effects are much larger for water than for hydrocarbon systems; and the natural steam production may or may not be isothermal, while production of petroleum reservoirs is considered normally to be isothermal. Petroleum reservoir engineering principles may be applied to natural steam or hot water reservoirs if the inherent differences in the systems are considered. The basic considerations involved in geothermal steam reservoir engineering are: thermodynamics, physical and thermal properties of water, materials and energy balances, fluid influx, and performance matching and predicting. Thermodynamics Fig. 1 is a pressure-temperature diagram for the liquid-vapor region for pure water, showing the critical point and five other points representing possible initial conditions for a geothermal steam reservoir. To generate a physical appreciation for the mechanics of natural steam production, it is helpful to consider

Jan 1, 1970

By Nelson Severinghaus

Mineral fillers have been defined as inert materials that are included in a composition for some useful purpose. Because this definition and the scope of this review are not specific- indeed, exceptions abound-accurate total statistics are unavailable. One source estimates the total production in the United States in 1971 at 5 million tons valued at $200 million, averaging $40.00 per ton. Included are a broad group of minerals-asbestos, barite, bentonite, calcium carbonate, clays, diatomite, feldspar, micas, silica, talc. Additional references will be made to synthetic mineral-derived fillers such as aluminum hydrate, precipitated calcium carbonate, and pyrogenic and precipitated silicas and silicates. A section on related uses at the end of this chapter covers absorbents and filters. Mineral fillers can be included in compounds to accomplish a variety of final results. Hardness, brittleness, impact strength, compressive strength, softening point, fire resistance, surface smoothness, electrical conductivity, and a host of other physical characteristics may be modified by the inclusion of fillers. These effects are the result of properties of the fillers, including chemical activity, hardness, particle size, shape and distribution, surface structure, color, density, and refractive index. To facilitate an overview of the mineral filler industry, this chapter will review the general usage of fillers, the inherent characteristics that intensify their utilization, and similarly their manufactured characteristics. Major using industries will then be examined in detail. Specific information on deposits and processing for industrial minerals will be found in the appropriate commodity chapter. The chart in Table 1, updated from the 3rd edition of Industrial Rocks and Minerals, illustrates the major mineral fillers (both natural and manufactured) and their more important end uses.

Jan 1, 1975

By Thomas Leonard Watson

Jan 1, 1906

By M. F. Trice

PYROPHYLLITE is a hydrous aluminum silicate (A12Si4010(OH)2)1 that occurs in both the foliated and the massive forms. The foliated variety resembles talc in that it has a greasy feel, a pearly luster, perfect basal cleavage, and usually is white, although in some deposits apple green, gray, brown, russet, and nearly black specimens may be found. The massive deposits of pyrophyllite yield pearl gray to light tan aggregates, some of which are so friable that they may be crushed with the hands into a fine gritty powder. Frequently specimens of the massive variety are studded with crystals of radial structure. The mineral has a specific gravity of about 2.7 and a hardness of 1 on Mobs' scale.1 The chemical composition of commercial pyrophyllite reflects the mineralogy of the deposits, which, according to Stuckey,2 contain pyro-phyllite and quartz, together with chloritoid, sericite, and a few other minerals of negligible importance. The latter, he says, "are noticed in but small quantities to the extent they might occur as accessory constitu-ents of an igneous rock or as products of regional metamorphism or weathering. . . . Quartz is abundant everywhere except in the very best grades of pyrophyllite." Analyses of specimens from several deposits are listed in Table 1, showing that the silica content varies from 57 to 73 percent and the alumina from 22 to 33 percent. Oxides of iron and the alkaline metals are collectively present, with one exception, to an extent of about 1 to 1.5 per cent.

Jan 1, 1940

By B. S. Gottfried

This paper is concerned with possible transport mechanisms which occur during segregated burning (i.e., burning in an oil reservoir in which the oil-bearing formation is overlain by a "clean" porous zone containing only gas). ,Two analytical models are presented. In the first, burning is assumed to occur at the gas-oil interface, and the dominant mechanism is taken to be the rate at which oxygen diffuses to the interface. The second model assumes that combustion occurs within the clean zone, with the dominant mechanism being the mechanism of fuel deposition from the oil-bearing formation to the clean zone. ,Comparison of the results of the analyses with limited experimental data indicates that the latter mechanism is much more plausible. Both models are idealized representations of the actual process and are somewhat conjectural, however, owing to the lack of more definitive laboratory or field data. INTRODUCTION In recent years there has been considerable theoretical and experimental research directed toward understanding the recovery of crude oil by underground combustion. Although two different recovery schemes have been proposed, known as forward and reverse combustion, it is only forward combustion that shows promise of becoming a practical recovery technique.17 Most of the analyses of the forward combustion process have considered it to be pistonlike; i.e., oil is displaced by a vertical combustion zone which, with its ensuing gases, pushes die oil forward as the flame front is propagated through the reservoir.l-8,ll,l2,14-16 However, information gained in field pilot studies indicates that, at least to a certain extent, forward combustion proceeds in a segregated manner in oil reservoirs.10 An ideal segregated system is one in which the oil-bearing formation is overlain by a "clean" porous zone containing only gas. The location of the combustion zone in such a system is not immediately evident, although combustion is believed to occur either at the gas-oil interface or within the clean zone. In either case, the combustion zone may be horizontal and it moves in parallel rather than in series with the produced oil. The purpose of this paper is to explore the likely mechanisms by which segregated burning can occur, and to determine the sensitivity of the resulting models to changes in various physical parameters. Two governing mechanisms are considered: the case of a horizontal combustion zone at the gas-oil interface with the rate of combustion governed by the rate at which oxygen diffuses to the interface, and the case of combustion within the clean zone with the combustion process controlled by the transport of fuel from the oil-bearing formation to the clean zone. Both models are somewhat hypothetical and involve considerable simplification of the actual process. However, the results allow some preliminary understanding of segregated burning which is useful in the absence of more definitive laboratory or field pilot data.

Jan 1, 1967

By W. C. Phalen

The production of salt in the United States divides itself at the outset into two distinct classes…

Jan 1, 1915

R. W. Raymond, New York, N. Y,:—Since the presentation of my note on this subject at the New York Meeting, Professor Louis has pointed out an error in my statement of his conception of " pitch "—namely, he understands the pitch, in the restricted sense which he proposes, to be the angle of inclination of the axis of an ore-body, measured on the vertical plane drawn through the body; whereas, I represented him as proposing to define " pitch " as the angle of inclination of an oblique body, measured on the plane of the dip, in the direction of the strike. The difference will appear upon consideration of the accompanying isometric projection, Fig. 1, in which ABCD represents the plane of the inclosing ore-deposit (vein or bed), and AC the axis of the oblique ore-shoot. ABE is the angle of the dip, as universally understood; and ACE

Jan 1, 1909

By V. N. Cox, C. H. Grant

Both the underwater method and the rock cratering method contribute useful information in evaluating and comparing new explosive compositions. Results indicate that metallized explosive systems which contain no high explosives can be formulated to offer more energy and to do potentially more work than other slurry explosive systems. Commercial field trials are presently being conducted with a metallized explosive that does not contain any high explosive. Although there have been only a few commercial blasts to date, the results are encouraging. The Dow Chemical Co. has been engaged in explosives research since 1953. The incentive for this research was based on the desire to find additional markets and uses for magnesium metal of which DOW is a heavy producer. The thermodynamic calculations for explosives incorporating light metals indicate energies approximately twice that of nonmetallized explosives currently being used. Early in 1960, additional patent rights were acquired from independent inventors and a development station at Virginia, Minn., was set up to conduct a commercial testing and market evaluation program with this new product. The actual manufacturing of the explosive was to take place in the boreholes. Due to the complexities involved in controlling the manufacture of the explosive in the borehole, performance was sometimes in doubt. Furthermore, experience indicated that the metallized explosive systems could not be evaluated by the standard laboratory methods then being used, and it was necessary for us to look for more suitable research methods. Tests were conducted on several known methods for explosive evaluation. The most promising were the Navy underwater method for energy evaluation and a modified Livingston crater method intended to compare explosive performance in rock. After shooting over 2000 charges of 8 to 60 lb under water and in taconites and granites with many types of explosives, a metallized explosive was developed which is now being manufactured at a pilot plant in Virginia, Minn. and is being evaluated commercially. UNDERWATER METHOD An underwater method of evaluating explosives has a number of advantages. A permanent site can be established and operated indefinitely. A large number of charges may be fired in a short length of time. The medium in which the explosive is shot is exactly the same for successive shots. Data are recorded electronically minimizing human judgment. A disadvantage of the underwater method is the lack of confinement provided by the water medium. Many explosive compositions require a greater degree of confinement to develop good energy release. Although the relative significance of the two components of energy release that are usually measured, the shock energy and the bubble energy, and their relationship to breaking rock are not clearly understood, the underwater method is a valuable research tool for screening explosive compositions and gaining an insight into the manner in which explosives release their energy. Fig. 1 shows schematically the underwater apparatus. The piezoelectric gages are calibrated tourmaline crystals which convert the shock wave to an electrical impulse which is transmitted to an oscilloscope and recorded on Polaroid film. The shock traces are picked up by scopes 1 and 2. Scope 1 is timed to pick up the full trace whereas scope 2 is timed to cover the first increment of the shock trace expanded, and therefore allows full inspection of the propagation and peak pressures. Scope 3 records the bubble trace. When the explosion occurs, a bubble of gaseous detonation products is formed. The outward momentum of the water keeps expanding the bubble even after

Jan 1, 1963

By C. S. Samis, D. P. Seraphim

In the presence of oxygen, galena is oxidized in an aqueous medium containing ammonium acetate in accordance with the following reaction: PbS + 1/2 0, + 2 NH~Ac -» PbAc, + So + 2 NH: + H2O. This reaction was studied in an autoclave under oxygen pressure by polarographic measurement of the concentration of lead ion in solution. Oxidation rate is parabolic. The reaction products are lead acetote and elemental sulfur, the latter forming a film on the galena crystal. Reaction kinetics appear to be determined by the diffusion of lead from the galena phase to the solution interface through the film of sulfur. RECENT applications of pressure leaching on a commercial scale have emphasized the metallurgical importance of the oxidation of sulfide minerals in aqueous media by oxygen under pressure. Research experience has shown that sulfates, thio-nates, and metal oxides are the products of humid oxidation of sulfide minerals in basic solutions. The metal oxides may be solubilized in the presence of a complexing ion.' Certain oxide minerals are also amenable to treatment by this type of oxidation.' Several kinetic studies have been made of reactions of this type. Stenhouse' found that pyrite (FeS?) oxidized in a sodium hydroxide solution to produce a soluble sulfate and an insoluble layer of iron oxide and that the kinetics of the reaction were controlled by oxygen diffusion through the oxide layer. Andersen' studied the oxidation of galena (PbS) in a sodium hydroxide solution under oxygen pressure. He found the lead and sulfur to be simultaneously oxidized to produce plum bite ions and sulfate ions, and that the reaction rate was proportional to the surface area of the galena. The kinetics appeared to be determined by the reaction of oxygen and water with the galena surface. In each of the above reactions the metal and sulfur components of the mineral were oxidized simultaneously and at equal rates. In the present study the alkaline medium has been replaced by an approximately neutral solution of ammonium acetate in which lead sulfate is soluble. Under the conditions no sulfate was produced and no sulfur could be detected in the solution. The metal component of the mineral was solubilized and the liberated sulfur remained as a film of elemental sulfur on the surface of the galena crystal. A kinetic study of this reaction was undertaken to establish the kinetic mechanism and to determine the rate controlling step. Specific reaction rates were determined by oxidizing crystals of galena of measured surface areas in an autoclave maintained at the desired temperature and oxygen pressure. The rate of reaction was followed by measuring the concentration of lead in the ammonium acetate solution with a cathode ray polarograph, employing stationary platinum electrodes incorporated in the autoclave. Experimental Materials and Equipment Crystals of galena obtained from Violamac Mines, Retallack, B. C., were selected for oxidation because

Jan 1, 1957

By J. J. Gilman

The dependence of ortho kink-band formation on crystal orientation, on temperature, and on the conditions at the ends of a specimen is described. Load-compression curves for crystals that kink are presented. The reversibility of ortho kinking is demonstrated, and motion of kink planes through crystals is shown. Finally, a phenomenological explanation of ortho kink-band formation is given. ORTHO compressive kink bands (Fig. la) were discovered for the case of metals by Orowan,1 and they have been discussed by Jillson2 and in some detail by Hess and Barrett." However, their history in nonmetallic crystals is considerably older. It is not known when they were first observed in mineral crystals, but descriptions of them may be found as early as 1885.* They were sometimes mistaken for twins.6 Mügge seems to have been first to realize their true nature and importance. He reviewed the knowledge of them for a wide variety of crystals: anhydrite, antimonite, kyanite, vivianite, gypsum, mica, graphite, molybdenite, barium bromide, cal-cite, sodium nitrate, and barite. Also, the "twins" observed by Bridgman7 in sapphire crystals resemble kink bands more than twins. The terms ortho and para kink bands have been coined in order to distinguish between two types of kink bands which seem to represent the same geometrical configurations, but which have different origins and sizes. Ortho kink bands are the usual type that form at low loads when zinc crystals are compressed parallel to the basal plane. Para kink bands form at much higher loads in highly deformed crystals. These terms refer to compression phenomena and are not to be confused with analogous tension phenomena such as tensile kink bands and deformation bands. Mügge described the geometry of ortho kink bands quite completely for kyanite crystals, Fig. lc. The geometry observed for cadmium by Orowan1 and for zinc by Hess and Barrett3 is very similar to that described by Mügge. (See Hess and Barrett for a complete discussion.) Mügge associated kinking with bending combined with basal slip. He pointed out that the kink angles

Jan 1, 1955

By W. L. Connell, O&apos

The properties of some heavy liquids which can be used in sink-float separations are discussed with major emphasis being given to the halogenated hydrocarbons. Data are presented on density, viscosity, thermal characteristics and the effects of moisture and temperature on the corrosiveness of the liquids towards various materials of construction. The toxicity of these materials, the hazards involved in handling them, and the procedures for handling them safely are also discussed. True liquids have certain advantages over colloidal suspensions for sink-float separation of minerals which makes their use especially advantageous when close separations, fine particle sizes or water-soluble minerals are to be treated. For best separating results, the medium should have an easily controlled, uniform, stable density. Here, true liquids have the advantages of allowing closer control of density and of not requiring agitation to maintain a uniform den- sity in the equipment. Low viscosities are desired in a separating liquid so that rapid separations of fine material can be made. Many liquids have lower viscosities than the colloidal suspensions at operating gravities of 1.4 to 5.0. For economic reasons and to prevent contamination of the product, the separating medium must be easily and completely removed from the ore. Normally, true liquids must be more completely removed than the cheaper suspensions and thus cause more problems in this area. The fact that the medium should not react with the minerals, air, water or the common materials of construction limits the choice of liquids which can be used, but many are available which are sufficiently stable. A more serious objection to the use of true liquids is that many of them present a toxic hazard to operating personnel and users of the product. Most true liquids are toxic to some extent, but modem knowledge of toxicity allows us to recognize the hazards inherent in handling them and enables us to design around them. Three types of true liquids are available for this use: 1) Halogenated hydrocarbons cover the gravity range from 1.2 to 3.3. They are generally more volatile and less viscous than the other liquids.

Jan 1, 1963

By Robert Leach

THIS paper gives a brief summary of the process of manufacture of sterling silver, and some of its more important physical properties, as observed in commercial production of rolled sheet and wire. Although papers have been published by Turner and Smith,1 Rose,2 Sperry3 and Jordan,4 there are few technical data available, and unfortunately the time allowed for the preparation of this paper has not been sufficient to make it as comprehensive as the title might indicate. ANALYSIS OF STERLING SILVER Fine or pure silver is too soft for coinage and the manufacture of articles in which strength and resistance to wear are desired. From the earliest times of which we have record, copper has been the metal generally used to harden silver. Analyses of coins and silver articles from ancient tombs show varying amounts of copper, and old Roman silver objects in the British Museum have approximately the same analysis as our sterling. The first authentic record of the establishment of a standard alloy is during the reign of Henry II in England. During the twelfth and thirteenth centuries, the people in the Eastern Provinces of Germany had a reputation for the standard and purity of their silver coinage, and it is said that Henry II employed some of these Easterlings, as they were called, to improve and standardize the English coinage, which had become debased. The peculiar standard adopted is probably accounted for by the system of weights used. A troy pound contains

Jan 1, 1928

By A. M. Khan, I. Fatt

A new type of steady-state thermal conductivity apparatus is presented and described. Results of measurements on Berea sandstone, Solehofen limestone, Bandera sandstone and Bakelite are presented. The measurements were made in a two-hour period at temperatures up to 80C and axial stress to 125 bars. Results show that the thermoelectric heat pump and tbermistor-controlled electric heater can be used in a steady-state apparatus for measuring thermal conductivity of mck. Steady-state is reached within two hours. With Urethane foam insulation, not more than 3 per cent of heat is lost by radial flaw. The apparatus can be used as a comparator or for absolute thermal conductivity determinations. INTRODUCTION Calculations of heat flow through the earth, both for scientific purposes and engineering design, require thermal-conductivity data on rock. However, the high variability of rock often makes handbook thermal-conductivity data of little value. For engineering purposes in particular, it is desirable to have measured data on samples of the rock mass under study. Laboratory methods for measuring thermal conductivity of rock use either time-dependent1-3 or steady - state temperatures .4,5 The time -dependent (transient) techniques give thermal diffusivity from which thermal conductivity can be calculated if the specific heat and density of the sample is known. Most transient techniques require lengthy and involved sample preparation. Also, the accuracy tends to be low. Steady-state techniques are more exact and are the most commonly used. The steady-state methods, however, also have their difficulties. A long time is often required to reach steady state, troubles have been encountered in establishing good thermal contact between the heating and cooling elements and the rock sample, and unaccounted-for heat losses are difficult to prevent. In this paper we present a description of a new type of steady-state thermal conductivity apparatus. With it, measurements have been made in two hours at temperatures up to 80C and axial stress to 125 bars. Sample preparation is simple and no thermal conductivity standard is needed.6 APPARATUS Our steady-state apparatus is an improvement . over the conduction pile used by Zierfuss and van der vliet4 and Somerton.5 A linear heat flux is established through a conduction pile consisting of the rock sample and a standard material of known thermal conductivity in series. The thermal conductivity of the sample is calculated from the ratio of the temperature drop across the sample

Jan 1, 1966

By Herbert Clark Hoover, Lou Henry Hoover

SINCE the Sixth Book has described the iron tools, the vessels and the machines used in mink, this Book will describe the methods of assaying1 ores; because it is desirable to first test them in order that the material mined may be advantageously smelted, or that the dross may be purged away and the metal made pure. Although writers have mentioned such tests, yet none of them have set down the directions for performing them, wherefore it is no wonder that those who come later have written nothing on the subject. By tests of this kind miners can determine with certainty whether ores contain any metal in them or not ; or if it has already been indicated that the ore contains one or more metals, the tests show whether it is much or little ; the miners also ascertain by such tests the method by which the metal can be separated from that part of the ore devoid of it ; and further, by these tests, they determine that part in which there is much metal from that part in which there is little. Unless these tests have been carefully applied before the metals are melted out, the ore cannot be smelted without great loss to the owners, for the parts which do not easily melt in the fire carry the metals off with them or consume them. In the last case, they pass off with the fumes ; in the other case they are mixed with the slag and furnace accretions, and in such event the owners lose the labour which they have spent in preparing the furnaces and the crucibles, and further, it is necessary for them to incur fresh expenditure for fluxes and other things. Metals, when they have been melted out, are usually assayed in order that we may ascertain what pro- portion of silver is in a centumpondium of copper or lead, or what quantity of gold is in one libra of silver ; and, on the other hand, what proportion of copper or lead is contained in a centumpondium of silver, or what quantity of silver is contained in one libra of gold. And from this we can calculate whether it will be worth while to separate the precious metals from the base metals, or not. Further, a test of this kind shows whether coins are good or are debased ; and readily detects silver, if the coiners have mixed more than is lawful with the gold ; or copper, if the coiners have alloyed with the gold or silver more of it than is allowable. I will explain all these methods with the utmost care that I can.

Jan 1, 1950

By E. H. T. Whitten

Fundamental principles of trend surface analysis are briefly reviewed. Recent analyses of several granite masses illustrate the method of estimating the quantitative regional composition and also variation trends. Mineralogi-cal, bulk chemical, and other quantitative variates can be employed. Such results should improve gravimetric surveys (etc.) relying on correction terms based upon estimated rock composition. For the first time realistic estimates of the mean composition of rock bodies can be made with the aid of trend components. Deviation maps hold promise for delimitation of disseminated mineralized areas. Deviations comprise residual "anomalies" after removal of trend components. In petrogenetic work such deviations have been shown to reflect local influences (e.g., contamination of magma by assimilation of xenoliths or country rocks of the envelope). Similarly, mineralization should be reflected as deviations standing out from background trends. Actual examples are given. Present results largely involved projection of data onto a horizontal plane, but if sufficient data are available use of three spatial coordinates increases accuracy for prediction in "unexposed" areas. Regression analysis shows that statistical correlations between variates for regionally distributed specimens are often strong (particularly with percentage data). Hence, in preliminary surveys more easily determined variates may sometimes be employed to gain first estimates of the distribution of components more economically significant. The sampling plan is of paramount importance. Unless a suitable sampling plan is devised and adhered to rigorously during collection of the samples, all subsequent analysis is liable to strong bias and to yield spurious estimates of the truth. For a wide variety of purposes it is becoming necessary to assess the quantitative composition and variability of rock masses and mineralized zones of various types. In petrology and petrography this is something of a break with tradition, because virtually all descriptions heretofore have been qualitative. Although vast amounts of qualitative data have been compiled, little is known about the quantitative behavior of rock components. However, if variability of rocks could be understood and expressed with sufficient accuracy, there would be considerable advantage to both economic and petrogenetic problems. For example, if, on the basis of a limited series of observations, the three-dimensional geometry of a disseminated orebody (or ore-bearing formation) could be predicted accurately, it would be possible to extrapolate with confidence the structure into unexposed areas. The following example based upon the geometry of an igneous cone sheet illustrates the point. The significant rock-unit gives outcrops at a number of points on the exposed surface ABCD (Fig. 1A). Study of n exposures may enable a geologist to predict that the rock-unit is circular in form and thus indicate where the unit can be expected in unexposed terrain. Such observations are made at sites with u, v coordinates, but, if subsurface information is available at sites with uvw coordinates, it will eventually become possible to predict accurately the three-dimensional form of the rock mass. Geologic rock masses or mineral deposits are not generally as regular and symmetrical in geometric form as the body illustrated in Fig. 1A. However, even where the broad limits of a major rock mass are known, a more acute problem arises in attempting to obtain detailed quantitative estimates of its internal variability; it is difficult to predict the variability of a mass from a limited number of observa-

Jan 1, 1961

By J. S. UNGER

A LARGE proportion of the coke used is made in the by-product oven from the high-volatile coals mined in the adjacent district. At the beginning it was feared good by-product blast-furnace coke could not be made with our coals. By experimenting with various mixtures of coals, coking time, oven design, and coking temperatures, much has already been accomplished. The results show that a hard, dense coke, not easily broken by handling, can be produced. In its present state it is not all that could be desired, but it is being constantly improved. Such coke has been used alone as the fuel on several of the blast furnaces producing the highest daily production in the Pittsburgh district. Many of the coals in the Pittsburgh district when coked in the by-product oven yield a gas which contains a high percentage of sulfur, which is objection- able for many metallurgical operations. As this fuel is gradually replacing the ideal fuel, natural gas, which is becoming less plentiful, studies are being made of the best methods for purification. Some metallurgists believe sulfur to be a very injurious element in steel. Recent investigations by Government bureaus, scientific bodies and private firms, seem to indicate that a reasonable amount of sulfur may exist in steel without detriment. Without wishing to provoke any metallurgical controversy on the subject of sulfur, the fact remains that the daily purification

Jan 1, 1926

By Henry Rawdon

THE following note describing the behavior of copper under rather unusual conditions is offered here for its suggestiveness rather than as a complete study of the question. The examinations described were made because of a request for information concerning the embrittlement of copper when heated in a molten salt bath (sodium chloride) for the purpose of cleaning it, as well as for softening it. It is well known that metals may be rendered very brittle by electrolytic action, in aqueous solutions, in all probability by the action of nascent hydrogen, and it was suspected that perhaps the embrittlement of the copper by means of the molten salt was produced in a somewhat similar manner. It was found that the copper was in contact with iron (or steel) while immersed in the molten salt, through the occasional use of an iron stirring rod, iron forceps for handling the pieces, and an iron pot for containing the fused salt. In the electrochemical potential series iron and copper stand some distance apart, copper being electronegative to the iron. Assuming that the two metals bear a similar relation to each other, when immersed in a bath of molten salt, as they do in an aqueous solution, they would be expected to form a galvanic couple, the copper being the cathode. By this means the copper might be embrittled, as often happens in aqueous solutions, by the action of the liberated hydrogen. In this case, however, the embrittlement must be attributed to some other agent than hydrogen. To demonstrate how copper may be embrittled under these conditions, two small rods, one of copper and the other of mild steel, approximately 3/8 in. (9.5 mm.) in diameter, were immersed in a bath of sodium chloride that had been heated somewhat above its fusion point (melting point of sodium chloride is 819° C.) and an electromotive force of approximately 6 volts from a storage battery was impressed upon the system. The copper was made the cathode and the action was continued for

Jan 2, 1920

By E. T. Turkdogan

Jan 1, 1962

By C. E. Sims

THE following presentation is more a summation of observations made and conclusions drawn over a period of three to four years than a report of experiments made with a definite objective. Tests were made, of course, to verify hypotheses, but the large mass of data was collected incidental to other work. Lack of space forbids the presentation of more than a few of those data. On the other hand, it is unfortunate that some of the most illustrative examples are not available. The work is admit¬tedly incomplete but is presented in the hope that it will stimulate further work along a similar line. The answers to many of the questions left unanswered by this paper will be found only after long and painstaking study, such as is scarcely possible in a commercial laboratory where problems of immediate importance consume most of the time. It is also hoped that this study will in some measure throw light on some of the dark spots of steelmaking, and help to clarify some of the annoyingly vague references to "good practice." Only cast steel was studied and the conclusions apply to cast steel, but it is the authors' opinion that the quality of rolled or forged steel is largely dependent on the quality of the ingot, which is a casting. Although this discussion deals almost entirely with inclusions, it is important that the reader understand that only those natural inclusions which owe their origin to the solubility of certain materials in steel and to the chemical reactions of steelmaking are considered. Accidental inclusions, such as entrapped particles of slag, nozzle, runner, or mold are outside its province and are not considered. Such accidental inclusions are always dangerous and should be carefully avoided.

Jan 1, 1932