Search Documents

By Marcos Paulo da Silveira, Carolina Conter Elgert, Messias Prado de Almeida, Rafael Stella Galdino

Microalloyed steels have been intensely studied as an alternative to increase strength by grain refinement and/or precipitation hardening. Long steel products have a wide range of opportunities to apply well-defined principles of controlled rolling (CR) in order to increase strength and toughness with reduced costs. To evaluate the effect of microalloying elements as Nb and Ti with thermomechanical treatment, three conditions were tested: DIN 16MnCrS5 with hot rolling (HR), DIN 16MnCrS5 with Nb and CR and DIN 16MnCrS5 with Nb+Ti and CR. Austenitic grain size, obtained by direct quenching after rolling, has shown a decrease 32% with Nb addition, and 29% when Nb and Ti was added. Controlled rolling generated higher grain refinement and pancacked grains near the surface. When comparing ferritic grain size, controlled rolling plus niobium and titanium additions resulted in significant reduction of 35%. Yield strength increased 15% with microalloying and CR and more than 270% in impact toughness, even at -40°C.

Oct 1, 2019

By Johan Richaud

Achieving high surface quality steel in the continuous casting process requires optimal mould level control. The design of the casting channel from the tundish to the mould is crucial to prevent formation of undesired instabilities or biased flows that can cause level fluctuation. With the aid of CFD and with physical water models, the geometry of the stopper nose and the nozzle seat have been studied and optimized to improve the overall mould flow stability. A special stopper nose; Ripple Stopper (RST), has been developed that reduces the formation of large and unwanted eddies in the liquid steel that destabilize the port exiting jets. Instead, the RST produces a fast release of turbulence in the form of a large number of small eddies. The large sudden fluctuations in the mould level are reduced, which in turn reduces the occurrence of surface defects. An additional benefit is derived from the local pressure around the stopper nose region being greater which reduces the refractory erosion. For a tundish gate type flow regulation, a new design encompasses an offset in the Tundish Well Nozzle (TWN) that realigns the flow and reduces the bias flow that is common to tundish gate regulation. The steel recirculation regions below the throttling gate are decreased reducing the risk of oxide depositions. The RST and the Offset bore casting channel have been applied successfully leading to a superior flow control performance between the tundish and the mould.

Jul 30, 2018

By José Adilson de Castro

In this paper a new technology for a compact iron ore sintering machine is analyzed. The compact sintering process is based on the massive injection of gaseous fuels and the solid fuel is only agglomerated fine charcoal obtained by biomass. The solid fuel used in this study is obtained by agglomeration of fine charcoal produced from elephant glass which has very short period for production and CO2 capture(less than 6 months in tropical climate). To overcome the lower heat supply into the combustion front of the sintering process the simultaneous injection of oxygen and gaseous fuel is proposed. The proposed methodology is to combine the solid fuel (agglomerated fines charcoal) and steelworks gases in a compact machine to enhance heat and mass transfer with high productivity (about 5 times the conventional large machine). A multiphase mathematical model based on transport equations of momentum, energy and chemical species coupled with chemical reaction rates and phase transformations is used to analyze the inner process parameters. A base case representing a possible actual industrial operation of the sintering machine is used in order to compare different scenarios of practicable operations which represents advanced operations techniques. The model was used to predict six cases of combined operation with biomass and fuel gas utilization with oxygen support.

Aug 2, 2018

By Rodrigo Fina Ferreira, Jacek Kolacz, Luciana Gois, Neymayer Pereira Lima

The recent developments on the sensor detectors together with the higher capacity of the machines, due the high-speed computing recent advances, have made possible extending the application in the mining industry. The use of x-ray fluorescence, x-ray transmission and radiometric sensor based sorting can selectively remove gangue minerals in different size fractions for different minerals. This paper summarizes the potential application of SBS for an iron ore in three size fractions aiming to increase the %Fe after the removal of particles with main gangue minerals associated. Pilot plant tests were carried out with samples of iron ore in different size fractions and different content of hematite and gangues. The use of x-ray transmission sensor showed the possibility to increase the %Fe from about 63% to above 68% for particles below 80mm and 45mm, after the removal of low density particles. The presence of fines on the feed affected the performance of the SBS X-rays transmission machine, especially for the fine fraction feed. The mineralogical determination, carried out to know the association between hematite and gangue minerals, and the density of the particles on the feed, can be used to preview the quality of products of the x-transmission sorting process.

Oct 3, 2019

By Nelson SOUTO, Nicolas LEGRAND, Christian COUNHAYE, Don EARLEY

The work is motivated by the automotive customer requirements for a roughness with high peak density (RPc > 75 peaks/cm) on steel sheet surfaces to maintain a good strip surface finish after painting. For that purpose, a new approach is utilized to compute roughness transfer and predict final roughness on uncoated steel sheets (average roughness, skewness, peak density) as a function of temper rolling conditions. The approach is based on the Monte Carlo method combined with the Abott curves and an auto-correlation function to numerically generate roughness profiles for roll and strip respectively. To compute the roughness transfer due to the interaction between roll and strip surfaces during rolling, a composite Abott curve that combines roll and strip Abott curves is used with an asperity crushing model integrated with a rolling model. This enables simulating two roughness transfer mechanisms in the roll bite: the strip asperity crushing mechanism by roll roughness and the strip asperity ploughing mechanism due to roll-strip interfacial sliding speed. The model shows the importance of considering the two mechanisms to predict roughness transfer correctly when strip elongation is high, typically a few percent, and roll bite friction is low. In these conditions, the forward slip at the exit of the roll bite tends to erode strip roughness significantly and decrease considerably the peak density on the strip. For lower elongation levels (~1%) and high roll bite friction, the ploughing mechanism becomes negligible and roughness transfer is controlled by the crushing mechanism only. With these two mechanisms, the model reasonably predicts the evolution of average roughness and peak density over a wide range of temper rolling conditions (new/worn work rolls, hard/soft grades, various elongations), but skewness is more difficult to predict for some trials.

Oct 1, 2019

By Sander Mul, Michael Brandner, Armin Paar

Graphitic HSS roll grades such as ESW’s brand VANIMO can be considered as the latest developments for the last finishing stands in hot strip mills. These roll grades are developed on the basis of the alloying concept of (Carbide Enhanced) Indefinite Chill work roll materials. During the development of VANIMO, the amounts and types of carbide forming elements were increased and adjusted into the direction of cast HSS roll grades. The microstructure of graphitic HSS roll grades therefore consists of tempered martensite, cementite and several different carbide types as well as a well-defined amount of free graphite. The main purpose of graphitic HSS roll grades is to combine the high surface quality of Indefinite Chill alloys as well as the high wear resistance of HSS roll grades. Several systematic steps were taken to increase the wear performance from Carbide-Enhanced Indefinite Chill grades to the more advanced VANIC grade and further on to the highest alloyed roll grade VANIMO. In every development step, the surface quality of the roll grades was carefully monitored. The decision to invest in new testing equipment at ESW’s plant was driven by the wish to see microstructural effects of different alloys in a macroscopic dimension. Usually samples are taken from cast rolls and investigation is done in comparably small areas compared to the total surface of a roll. Rolling of strip is done with the entire barrel, so effects of alloy and microstructure can appear anywhere on the barrel surface. To ensure better understanding and deeper knowledge about influences of alloying trials we decided to install the last version of LRI (Lismar Roll Inspection). LRI includes the latest technology of Eddy Current with an enormous resolution. Depending on the formation of carbide precipitations, carbide network as well as matrix and free graphite, the EC test can detect smallest differences. The possibility to analyze the different results of EC and UT surface wave inspection will be discussed. A few examples of surface effects in the mill application will be discussed and improvement strategies explained.

Oct 1, 2019

By Carolina Arriel Pedroso Dias

Neste trabalho, tiras de aço inoxidável duplex UNS S32205 foram laminadas a morno a 600°C com 60% e 80% de redução e, em seguida, foram recozidas a 1050°C durante 300 s. A tira como fornecida (laminada a quente industrialmente e recozida) também foi recozida para efeito de comparação. Avaliou-se o comportamento mecânico das amostras como fornecida, 60% e 80% por meio de ensaios de tração e microdureza Vickers, obtendo-se 779 MPa, 730 MPa e 807 MPa de limite de resistência a tração e 265 HV, 244 HV e 256 HV de microdureza Vickers para as três condições descritas, respectivamente. Outros ensaios de microdureza foram realizados ao longo da superfície do corpo de prova fraturado em tração, indicando um aumento da dureza nas regiões mais próximas da fratura. O aumento da dureza na região de estricção indicou o aparecimento da martensita induzida por deformação para as amostras laminadas a morno. Usando a derivada da curva tensão verdadeira em função da deformação verdadeira, (ds/de), avaliou-se o comportamento de encruamento do aço para as três condições. Juntamente com os exames por microscopia eletrônica de alta resolução e difração de raios X, buscou-se uma interpretação dos mecanismos de deformação plástica envolvidos no processo de encruamento. Em determinados estágios, observou-se uma mudança da inclinação para um regime estável, indicando a ocorrência de outros mecanismos de deformação plástica, diferentes do escorregamento de deslocações. A martensita induzida por deformação foi considerada responsável pelo aumento da taxa de encruamento do aço, i.e., por ser obstáculo à movimentação das deslocações e por postergar a formação da estricção.

Oct 30, 2017

By Ernst Lindemann

Steel suppliers are required to deliver sheets with particular qualities and with lightweight-potential to the automotive industry. New types of steel call for new production processes. SMS group has developed a new micro-mill-concept, the core of which is the belt caster. This was first built on an industrial scale and has been put into operation and developed together with Salzgitter Flachstahl GmbH. The robustness in industrial-scale operation could be verified. The full use of the belt casting technology, mainly related to energy efficiency and CO2 reduction, is realized with the micro-mill-concept. This is an in-line-process, casting and rolling in one line.

Aug 17, 2017

By Pierre Montmitonnet, Yukio Shigaki, Jonatas Mezêncio Silva

A precise roll stack deformation model of a flat rolling mill is crucial for strip profile assessment as it depends strongly on the roll’s deformation. The need for more and more advanced products with stringent both geometrical and mechanical tolerances (e.g., Advanced High Strength Steels – AHSS), with thinner and harder steel strips, demands more advanced simulation models. The present paper addresses assumptions made in Finite Element Method (FEM)-based roll stack models on some important, yet barely discussed features: What is the impact on precision of the simplifications such as symmetry and anti-symmetry? Should roll neck boundary conditions in bearings be considered as fixed or simply supported? In this paper a hybrid model developed by the authors for a general flat rolling mill is used to assess those questions. This model runs much faster (100x in some cases) than a whole-FEM-modeled 6-high rolling mill with the elastoplastic strip deformation, thanks to its simplifications adopted. This model assumes a steady state rolling condition, and the roll stack is modeled with tridimensional finite elements, and the loads are calculated via a slab method adopting a plane strain state for the strip deformation (especially true for thin strips). An industrial 6-high cold rolling mill is modeled and results on the application of symmetries and different boundary conditions on the roll’s necks are presented. It is concluded that the application of symmetries and anti-symmetries for the 6-high rolling mill is possible for thin strips. And the way the necks are modeled does not impact on the final strip shape, though it influences the magnitude of the roll’s displacement. The coupling of the strip with the work roll applied assuming a symmetry plane of the arc of contact has little influence on the strip shape.

Oct 1, 2019

By Božidar Šarler, Umut Hanoglu

A rolling simulation system has been developed to calculate the macroscopic rate of deformation, stress, strain, and temperature fields by using a novel meshless method. The model is based on two-dimensional traveling slice assumption. The slices are aligned towards the rolling direction. The initial size of the billet, bloom or slab and the geometry of the grooves at each rolling stand, the distances between the rolling stands, and continuous or reverse rolling can be arbitrarily considered. The purpose of this paper is to complement these development by predicting and visualizing also the grain size of steel over the strand cross-section for each position in the rolling mill. The grain size models have been in one-way coupled to the macroscopic calculations. First the critical strain for dynamic recrystallization is being checked. If the calculated strain is higher than that, considering also the time for meta-dynamic recrystallization, dynamic or meta-dynamic grain size calculations are carried out. If the strain is too low then only the static recrystallization is considered together with its required time. Finally, austenite grain size and ferrite grain size are calculated respectively as the steel cools down. The listed physical models are based on collection of empirical relations found in literature. The user of the system is free to choose or create the model he wants with his own parameters. The simulation system has been coded as a user friendly computer application for an industrial use based on C# and .NET framework and runs on regular PCs. The computational time for a rolling simulation is usually less than one hour and can thus be straightforwardly used for optimization of the rolling mill design in a reasonable time.

Oct 1, 2019

By Michelle Lacerda Sales Marques

A busca de novas rotas de beneficiamento que possam maximizar a recuperação metalúrgica e mássica é uma constante na Vale. O trabalho foi desenvolvido em três fases, onde foram estudadas quatro rotas de beneficiamento que buscaram reduzir a geração de ultrafinos e, assim, aumentar a recuperação mássica. Foram avaliadas rotas com pré-concentração do minério em concentração magnética (rota denominada PCM) e flotação (rota denominada MFMF), e uma rota onde a moagem mais grossa (P80 0,15mm) permite uma menor geração de ultrafinos (rota denominada MDMF). Esta última apresentou um CAPEX 6,5% menor quando comparado a rota PCM.

Aug 1, 2018

By Roberto Parreiras Tavares, Leonardo José Silva de Oliveira, Marcelo Moreira Furst Goncalves, Rodrigo Seara Martins

Os pós fluxantes estão continuamente sendo desenvolvidos para permitir que o processo de lingotamento contínuo possa gerar produtos de melhor qualidade superficial. Entretanto, a seleção e a avaliação do desempenho industrial desse insumo não são simples por envolver o conhecimento simultâneo de várias propriedades físico-químicas. Nesse sentido, desde que medido de forma adequada, o consumo do pó fluxante no molde é uma ferramenta útil para avaliar a estabilidade operacional. Assim, foi desenvolvido um sistema para quantificar o consumo específico dos pós fluxantes no molde para posteriormente correlacioná-lo com eventos que possam levar a desvios de qualidade superficial do produto lingotado.

Oct 1, 2019

By Fabio Da Costa Garcia Filho

O uso de resíduos de vidro como aditivo mineral finamente moído, em substituição parcial de cimento e agregados é uma direção promissora para a reciclagem. Este trabalho teve como objetivo analisar a influência de resíduos do processo de corte de vidro em argamassa adesiva, como substituição parcial de cimento e agregado miúdo. O vidro em pó foi utilizado em percentuais de 10, 15 e 20% em peso em substituição ao cimento Portland e, em outro momento, em substituição ao miúdo agregado. Verificou-se que a substituição refletiu positivamente sobre a resistência à adesão da argamassa, com o aumento da temperatura de cura.

Oct 30, 2017

By Saulo Rossini Meira

A complexidade e o elevado tempo de manutenção para a troca do rolamento da grelha móvel do forno da usina de pelotização IV, localizada no Complexo de Tubarão em Vitória - Espírito Santo, viabilizou estudar, desenvolver e implementar, via PDCA, uma solução tecnológica que reduziu riscos de acidentes, tempo de manutenção, desgaste físico e mental, como também eliminou a utilização de equipamentos móveis e o risco de quebra de componentes periféricos. Conclui-se que com a modificação implementada, foram viabilizados procedimentos de manutenção mais seguros, redução de custos e aumento da disponibilidade do equipamento para o processo produtivo.

Aug 1, 2018

By Jorge Luis Braz Medeiros

As ligas de Alumínio ASTM 2014, caracterizam-se por apresentarem elevada resistência mecânica, quando comparadas a demais ligas de Alumínio. Este comportamento está associado ao tratamento térmico de Solubilização e envelhecimento, sendo que no envelhecimento artificial existem diferentes curvas de avaliação do limite de resistência, limite de escoamento, alongamento etc. Neste trabalho serão apresentados os efeitos da cura de revestimento de Politetrafluoretileno, realizado a 230ºC, nas propriedades mecânicas e na dureza, destas ligas, após a condição preliminar de solubilização. O Politetrafluoretileno confere baixo coeficiente de atrito e acabamento diferenciado, sendo comparado seu efeito com processos de anodização.

Aug 7, 2018

By Wallace Ernesto Sant Anna Ramos

Um dos grandes desafios na área Utilidades e Energia da Indústria Siderúrgica é a manutenção da qualidade da água dos sistemas de Lavagem de Gases da Aciaria e Altos Fornos, em função das diversas impurezas existentes neste processo o que pode gerar altos custos de manutenção ao longo do ano. Este trabalho visa mostrar as vantagens e benefícios de se utilizar um Tratamento Químico adequado na água dos sistemas de Lavagem de Gases da Aciaria e Alto Fornos com foco redução de horas paradas de manutenção preventiva e corretiva, aumento da performance dos equipamentos, otimização de mão-de-obra dentre outros.

Oct 30, 2017

By Camila Simon Christ

A crescente demanda de aços com composições e propriedades controladas aumenta as exigências do controle de qualidade dos produtos acabados e dos constituintes deletérios, como as inclusões, que são agregados durante os processos de fabricação e acabamento. No presente trabalho foi realizada uma análise qualitativa e quantitativa das inclusões presentes em um aço microligado de partida de máquina, através da observação de imagens obtidas por microscópio ótico. A observação das imagens permitiu verificar uma falta de homogeneidade ou padrão na ocorrência das inclusões nas amostras e que as inclusões presentes eram do tipo óxidos glogulares e alumina.

Oct 30, 2017

By Leandro Moraes da Silva Graciotti, Lorenzo Bortolon Scandian

Este artigo tem como premissa apresentar o quadro evolutivo referente a Segurança do Trabalho no Terminal de Produtos Siderúrgicos (TPS) do porto de Praia Mole bem como mostrar as novas ferramentas e tecnologias aplicadas ao processo portuário para garantir a perenidade das operações. Neste documento apresentaremos o Terminal de Produtos Siderúrgicos, sua estrutura de funcionamento, e as operações executadas. Em seguida, explicitaremos as ferramentas de gestão de segurança utilizadas e suas tecnologias. Por fim, exibir-se-á os impactos provenientes dos recursos e ações de segurança executadas, enfatizando a importância da tecnologia em conjunto com a segurança do trabalho no TPS.

Oct 1, 2019

By Rudolf Lesch

Till date, coke has been produced mainly from coals with a content of volatile matters in the range of 20% to 28% and good coking properties. If such so-called "selfcoking" coals are available, blast furnace coke or foundry coke with the required quality characteristics can be produced in top-charged horizontal ovens. In this case, the possibility of using high-volatile coals and in particular coals with low-caking properties is very restricted. Even if high-volatile coking coals have good coking properties, coke produced from such coal alone will not meet the requirements in terms of coke strength. The mechanical coke properties are influenced by the charge coal blend and the coking conditions. In this context, the bulk density of the oven charge is a decisive factor. Research and development in the field of coke production in horizontal chamber ovens aims at improving the specific oven throughput, increasing the raw material basis and introducing environmental protection technologies. The key factor, however, is to guarantee and further improve the rentability of the coke production. It is very important to reduce the cost of the charge coal to a minimum at the same time maintaining or even improving the coke quality.

Aug 17, 2017

By André De Araujo Abilio

Geopolímero é um material inorgânico formado por ativação alcalina durante a qual processos de polimerização de alumino-silicatos formam a cadeia polimérica que consiste em tetraedros de Si-O e Al-O. Com o intuito de encontrar subprodutos para serem usados como uma alternativa de aglomerante na formulação do geopolímero, um subproduto oriundo do processamento de rochas ornamentais foi utilizado. O presente estudo consiste na caracterização da capacidade de flexão do material geopolimérico resultante da adição do granito como aglomerante alternativo. Estudos foram elaborados de modo a avaliar ambos o efeito e a viabilidade de seu uso em formulações futuras do geopolímero.

Aug 16, 2017